Filters for Communication Lines Analog Systems and Control Lines Series/Type: B84312 Date: January 2004 EPCOS AG 2004. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed. Filters for communication lines B84312 Analog systems and control lines Passband up to 300 kHz Stopband attenuation up to 40 GHz Features Use of coaxial feed-through capacitors on input and output Single or current-balanced chokes depending on requirement Insertion loss to CISPR 17 Also available with integrated EMP protection Installation Single filters are attached directly to the shielding wall. Larger numbers can be housed in filter cabinets or boxes. Various models and the matching flexible connector fittings are available. Mechanical design The electrical components are incorporated in an RF-tight case of tin-plated sheet steel. Filters are available for 2 or 20 lines and for upright or flat installation on shielding wall. Model Installation Filter selection B84312C Upright Space-saving solution for installing a number of different filters. B84312C*B (2-line) B84312C*H (20-line) B84312F Low profile and thus advantage especially for just one or a few filters. B84312F*B (2-line) Flat 2 Filters for communication lines B84312 Analog systems and control lines Filter applications The following standard filters are designed for the most common applications; customized models can be produced for differing requirements. Passband ZL IR Application Circuit No. Series diagram of lines B84312 kHz Ω A DC ... 3.4 600 0.1 Standard filters for telephone systems 1 2 20 +0020B*** C0020H*** DC ... 3.4 600 0.1 Telephone systems for enhanced requirements (stopband attenuation of 100 dB above 10 kHz ) 3 2 20 +0090B*** C0090H*** DC ... 50 600 0.1 Filters for telephone systems and modem cables, conditionally for control lines with critical signal rise times 1 2 20 +0040B*** C0040H*** DC ...120 150 0.1 2 2 20 +0050B*** C0050H*** DC ... 300 150 0.1 Data signals with balanced signal transmission mode as used by modems or interfaces RS 485 up to 9600 Baud and/or RS 422 up to 19200 Baud 2 2 20 +0060B*** C0060H*** DC ... 120 100 2 Smoke detectors with serial data transmission in bus systems and remote power feeding, temperature switches, 24 V emergency lighting, DC motors 2 2 20 +0050B*** C0050H*** 3 24-V emergency lighting, DC motors, signal and control lines 2 2 20 +0050B*** C0050H*** 1 Universal filters for signal and control lines with up to 1 A 1 2 20 +0030B*** C0030H*** 1 Control lines with up to 1 A and enhanced attenuation requirements 3 2 20 +0100B*** C0100H*** +: C = upright installation, F = flat installation 3 Filters for communication lines B84312 Analog systems and control lines Circuit diagrams The diagrams each show a circuit of a 2-line filter. In the series of 20-line filters there are 10 of them in each case. Circuit diagram 1 Circuit diagram 2 Circuit diagram 3 Note on circuit diagrams 2 and 3: These filters are mounted with current-compensated chokes. Make sure that the forward and return line are routed paired through one filter. 4 Filters for communication lines B84312 Analog systems and control lines General technical data Rated voltage VR,AC 100 V Rated voltage VR,DC 100 V Rated frequency fR Rated current IR See characteristics Line impedance ZL See characteristics Test voltage Vtest 250 VDC, 2 s 250 VDC, 2 s Maximum DC resistance Rmax See characteristics Pass bandwidth at Z L TA = 40 °C Line/line Line/case Per line Permissible ambient temperature TA 25/+40 Climatic category (EN 60068-1) 25/085/56 Weight 560 4.5 Mechanical version C Upright for 2- and 20-line filters F Flat for 2-line filters °C 25 °C/+85 °C/56 days damp heat test g 2-line filters kg 20-line filters Filters with EMP protection: Nominal DC spark-over voltage <500 V Per line Surge response voltage VsdcN <800 <800 V V At 1 kV/µs At 1 kV/ns Nominal surge current (8/20 µs) 5/10 kA Suppression condition I ≤ IR Maximum voltage on filter output for filters with EMP protection Series B84312 ...0020+1** ...0030+1** ...0040+1** ...0050+1** ...0060+1** ...0090+1** ...0100+1** Pulse shape in symmetrical circuit dv/dt = 0.1 kV/µs 2V 360 V 8V 3V 12 V dv/dt = 1 kV/µs 60 V dv/dt = 1 kV/ns1) 1V 0.5 V 2V 3V 0.5 V 2V 0.5 V 9V 1.2 V 5V 290 V 12 V 10 V 12 V Nominal surge current (8/20 µs) Pulse shape in unsymmetrical circuit dv/dt = 0.1 kV/µs 50 V 700 V 250 V 120 V 280 V dv/dt = 1 kV/µs 35 V 130 V 60 V 25 V 30 V dv/dt = 1 kV/ns1) 1V 5V 3V 1V 1V 20 V 200 V 110 V 25 V 50 V Nominal surge current (8/20 µs) 1) Typical test pulse: rise time 10 ns, time to half value 1500 ns, charge voltage min. 50 kV, source impedance 90 Ω 5 Filters for communication lines B84312 Analog systems and control lines Characteristics and ordering codes IR Pass bandwidth kHz DC ... 3.4 DC ... 3.4 DC ... 3.4 2) 2) 2) DC ... 50 DC ... 50 DC ... 50 DC ... 120 DC ... 120 DC ... 120 DC ... 120 DC ... 120 DC ... 120 2) 2) 2) DC ... 300 DC ... 300 DC ... 3.4 DC ... 3.4 DC ... 3.4 2) 2) 2) ZL Rmax Per line Ω A Ω 0.1 600 11 0.1 600 11 0.1 600 11 3) 0.4 1 3) 0.4 1 3) 0.4 1 0.1 600 1.1 0.1 600 1.1 0.1 600 1.1 0.1 150 4.4 0.1 150 4.4 0.1 150 4.4 100 0.4 2 100 0.4 2 100 0.4 2 3) 0.2 3 3) 0.2 3 3) 0.2 3 0.1 150 1.0 0.1 150 1.0 0.1 600 17 0.1 600 17 0.1 600 17 3) 0.6 1 3) 0.6 1 3) 0.6 1 *: 0 = Standard filters 1 = Filters with EMP protection Circuit diagram Number of lines Ordering code 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 2 2 20 2 2 20 2 2 20 2 2 20 2 2 20 2 2 20 2 2 2 2 20 2 2 20 B84312C0020B*03 B84312F0020B*03 B84312C0020H*03 B84312C0030B*03 B84312F0030B*03 B84312C0030H*03 B84312C0040B*01 B84312F0040B*01 B84312C0040H*01 B84312C0050B*01 B84312F0050B*01 B84312C0050H*01 B84312C0050B*21 B84312F0050B*21 B84312C0050H*21 B84312C0050B*31 B84312F0050B*31 B84312C0050H*31 B84312C0060B*01 B84312F0060B*01 B84312C0090B*04 B84312F0090B*04 B84312C0090H*04 B84312C0100B*03 B84312F0100B*03 B84312C0100H*03 2) Control line filters, not matched 3) Not specified 6 Filters for communication lines B84312 Analog systems and control lines Insertion loss αe in passband (typical) Symmetrical measurement circuit with ZL = 600 Ω Symmetrical measurement circuit with ZL = 150 Ω 7 Filters for communication lines B84312 Analog systems and control lines Unsymmetrical measurement (common-mode-rejection) in passband Filter with ZL = 600 Ω CMR >40 dB in passband 8 Filters for communication lines B84312 Analog systems and control lines Insertion loss αe in stopband (typical) Unsymmetrical measurement circuit Asymmetrical measurement to MIL-STD-220A 9 Filters for communication lines B84312 Analog systems and control lines Dimensional drawings 2-line filters, upright installation ➀ Line connections at both ends: 2 x tab connectors for receptacle 2.8 x 0.5 (in accessory bag) ➁ Strain relief with ground connection for cable diameter 4.5 ... 6 mm Hole for installation in shielding wall 10 Filters for communication lines B84312 Analog systems and control lines 2-line filters, flat installation ➀ Line connections at both ends: 2 x tab connectors for receptacle 2.8 x 0.5 (in accessory bag) ➁ Strain relief with ground connection for cable diameter 4.5 ... 6 mm Hole for installation in shielding wall 11 Filters for communication lines B84312 Analog systems and control lines 20-line filters, upright installation Hole for installation in shielding wall Adapter A bracket adapter is available for flat installation on the shielding wall. Ordering code: B84298M0012C004 12