IS/ISO 9002 Lic# QSC/L- 000019.2 Continental Device India Limited An IS/ISO 9002 and IECQ Certified Manufacturer NPN SILICON PLANAR EPITAXIAL TRANSISTOR CSC458 TO-92 Plastic Package Low Frequency Amplifier. Complementary CSA 1029 ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL VCEO Collector Emitter Voltage VALUE 30 UNIT V Collector Base Voltage VCBO 30 V Emitter Base Voltage VEBO 5.0 V Collector Current IC 100 mA Emitter Current IE 100 mA Collector Power Dissipation PC 200 mW Tj, Tstg -55 to +150 Operating And Storage Junction Temperature Range ºC ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION MIN TYP MAX UNIT Collector Emitter Voltage VCEO IC=1mA,IE=0 30 V Collector Base Voltage VCBO IC=10µA,IE=0 30 V Emitter Base Voltage VEBO 5.0 Collector Cut off Current ICBO IE=10µA, IC=0 VCB=18V, IE = 0 500 V nΑ Emitter Cut off Current IEBO VBE=2V, IC = 0 500 nA 500 0.75 0.20 V V DC Current Gain Base Emitter On Voltage Collector Emitter Saturation Voltage Continental Device India Limited hFE VBE(on) VCE(sat)* VCE=12V,IC=2mA IC=2mA,VCE=12V IC=10mA,IB=1mA Data Sheet 100 <0.4 Page 1 of 4 NPN SILICON PLANAR EPITAXIAL TRANSISTOR CSC458 TO-92 Plastic Package ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION MIN DYNAMIC CHARACTERISTICS Transition Frequency Output Capacitance Input Impedance fT Cob TYP MAX UNIT IC=2mA, VCE=12V 230 MHz IE=0, VCB=10V f=1MHz 3.5 pF KΩ hie 16.5 IC=0.1mA, VCE=5V f=270Hz Output Admittance hoe 11 µs Voltage Feedback Ratio hre 70 x10-6 Small Signal Current Gain Noise Figure hFE CLASSIFICATION : Continental Device India Limited | hfe | NF B: 100-200 130 VCE =6V,IC=0.1mA Rg=5001KΩ , f=1KHZ C: 160-320 Data Sheet 10 dΒ D: 250-500 Page 2 of 4 CSC458 TO-92 Plastic Package TO-92 Plastic Package TO-92 Transistors on Tape and Ammo Pack Ammo Pack Style MECHANICAL DATA Uncontrolled h P T D FEE Adhesive Tape on Top Side h (p) A1 LABEL A H1 Carrier Strip FLAT SIDE 183 A Dimension With 'L' B W2 H0 L Wo W1 L W F1 t 1 F2 F 42 Do P2 Po K 2 3 D A A C 3 2 1 H F F ITEM 3 2 1 SEC AA G PIN CONFIGURATION 1. BASE 2. COLLECTOR 3. EMITTER 331 Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions in mm unless specified otherwise D E Beyond 'L' Solderability Ensured t1 DIM MIN. MAX. A B C D 4.32 4.45 3.18 0.41 5.33 5.20 4.19 0.55 E F G H 0.35 0.50 5 DEG 1.14 1.40 1.14 1.53 K L 12.70 1.982 All diminsions in mm. — 2.082 SYMBOL BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH A1 A T P Po FEED HOLE CENTRE TO COMPONENT CENTRE P2 DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION F h W Wo W1 HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, W2 Ho H1 L Do t F2 CLINCH HEIGHT PULL - OUT FORCE H2 (P) SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 5.2 4.8 4.2 3.9 12.7 ±1 12.7 ±0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 ±0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 0 1 AT TOP OF BODY 18 ±0.5 6 ±0.2 9 +0.7 -0.5 0.5 ±0.2 16 ±0.5 23.25 11.0 4 ±0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES. Packing Detail PACKAGE TO-92 Bulk TO-92 T&A STANDARD PACK Details Net Weight/Qty 1K/polybag 200 gm/1K pcs 2K/ammo box 645 gm/2K pcs Continental Device India Limited INNER CARTON BOX Size Qty 3" x 7.5" x 7.5" 5K 12.5" x 8" x 1.8" 2K Data Sheet OUTER CARTON BOX Size Qty Gr Wt 17" x 15" x 13.5" 80K 23 kgs 17" x 15" x 13.5" 32K 12.5 kgs Page 3 of 4 Notes CSC458 TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and on the CDIL Web Site/CD is believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-579 6150 Fax + 91-11-579 9569, 579 5290 e-mail [email protected] www.cdil.com MPS2222/ARev200701 Continental Device India Limited Data Sheet Page 4 of 4