AD AD8340 400 mhz to 6 ghz broadband quadrature modulator Datasheet

400 MHz to 6 GHz
Broadband Quadrature Modulator
ADL5375
Output frequency range: 400 MHz to 6 GHz
1 dB output compression: ≥9.4 dBm from 450 MHz to 4 GHz
Output return loss ≤ 14 dB from 450 MHz to 5.5 GHz
Noise floor: −160 dBm/Hz @ 900 MHz
Sideband suppression: <−50 dBc @ 900 MHz
Carrier feedthrough: <−46 dBm @ 900 MHz
Baseband input bias level
ADL5375-05: 500 mV
ADL5375-15: 1500 mV
Single supply: 4.75 V to 5.25 V
24-lead LFCSP_VQ package
FUNCTIONAL BLOCK DIAGRAM
IBBP
ADL5375
IBBN
LOIP
LOIN
QUADRATURE
PHASE
SPLITTER
RFOUT
DSOP
QBBN
07052-001
FEATURES
QBBP
Figure 1.
APPLICATIONS
Cellular communication systems
GSM/EDGE, CDMA2000, W-CDMA, TD-SCDMA
WiMAX/broadband wireless access systems
Satellite modems
GENERAL DESCRIPTION
The ADL5375 is a broadband quadrature modulator designed for
operation from 400 MHz to 6 GHz. Its excellent phase accuracy
and amplitude balance enable high performance intermediate
frequency or direct radio frequency modulation for communication systems.
The ADL5375 features a broad baseband bandwidth, along
with an output gain flatness that varies no more than 1 dB
from 450 MHz to 3.8 GHz. These features, coupled with a broadband output return loss of ≤−14 dB, make the ADL5375 ideally
suited for broadband zero IF or low IF-to-RF applications,
broadband digital predistortion transmitters, and multiband
radio designs.
The ADL5375 accepts two differential baseband inputs and
a single-ended LO. It generates a single-ended 50 Ω output.
The two versions offer input baseband bias levels of 500 mV
(ADL5375-05) and 1500 mV (ADL5375-15).
The ADL5375 is fabricated using an advanced silicon-germanium
bipolar process. It is available in a 24-lead, exposed paddle, Pb-free,
LFCSP_VQ package. Performance is specified over a −40°C to
+85°C temperature range. A Pb-free evaluation board is also
available.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
ADL5375
TABLE OF CONTENTS
Features .............................................................................................. 1
RF Output .................................................................................... 20
Applications ....................................................................................... 1
Output Disable ............................................................................ 21
Functional Block Diagram .............................................................. 1
Optimization ................................................................................... 22
General Description ......................................................................... 1
Applications Information .............................................................. 23
Revision History ............................................................................... 2
DAC Modulator Interfacing ..................................................... 23
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 7
Using the AD9779 Auxiliary DAC for Carrier Feedthrough
Nulling ......................................................................................... 24
ESD Caution .................................................................................. 7
GSM/EDGE Operation ............................................................. 25
Pin Configuration and Function Descriptions ............................. 8
W-CDMA Operation................................................................. 25
Typical Performance Characteristics ............................................. 9
LO Generation Using PLLs ....................................................... 26
ADL5375-05 .................................................................................. 9
Transmit DAC Options ............................................................. 26
ADL5375-15 ................................................................................ 14
Modulator/Demodulator Options ........................................... 26
Theory of Operation ...................................................................... 19
Evaluation Board ............................................................................ 27
Circuit Description..................................................................... 19
Thermal Grounding and Evaluation Board Layout............... 28
Basic Connections .......................................................................... 20
Characterization Setup .................................................................. 29
Power Supply and Grounding ................................................... 20
Outline Dimensions ....................................................................... 31
Baseband Inputs.......................................................................... 20
Ordering Guide .......................................................................... 31
LO Input ...................................................................................... 20
REVISION HISTORY
12/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 32
ADL5375
SPECIFICATIONS
VS = 5 V; TA = 25°C; LO = 0 dBm single-ended drive; baseband I/Q amplitude = 1 V p-p differential sine waves in quadrature with a
500 mV (ADL5375-05) or 1500 mV (ADL5375-15) dc bias; baseband I/Q frequency (fBB) = 1 MHz, unless otherwise noted.
Table 1.
Parameter
OPERATING FREQUENCY RANGE
Low frequency
High frequency
LO = 450 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
LO = 900 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
ADL5375-05
Min Typ
Max
Conditions
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 0.87 dBm
POUT = 0.46 dBm
POUT − (fLO + (3 × fBB))
POUT = 0.87 dBm
POUT = 0.46 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 0.87 dBm
POUT = 0.47 dBm
POUT − (fLO + (3 × fBB))
POUT = 0.87 dBm
POUT = 0.47 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
Rev. 0 | Page 3 of 32
ADL5375-15
Min Typ
Max
Unit
400
6000
400
6000
MHz
MHz
0.87
−3.1
9.4
−14.7
−48.0
−33.1
2.52
−0.05
−74.5
0.46
−3.5
9.9
−14.7
−52.2
−35.5
1.64
−0.07
−74.5
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−51.3
−77.1
dBc
65.0
67.9
dBm
28.1
23.0
dBm
−160.5
−157.0
dBm/Hz
0.87
−3.1
9.4
−14.1
−46.2
−52.1
−0.29
−0.05
−73.3
0.47
−3.5
9.9
−14.1
−46.2
−50.4
−0.37
−0.07
−73
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−51.5
−71
dBc
68.3
66.2
dBm
26.8
22.9
dBm
−160.0
−157.1
dBm/Hz
ADL5375
Parameter
LO = 1900 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
LO = 2150 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
ADL5375-05
Min Typ
Max
Conditions
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 1.01 dBm
POUT = 0.63 dBm
POUT − (fLO + (3 × fBB))
POUT = 1.01 dBm
POUT = 0.63 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 1.05 dBm
POUT = 0.67 dBm
POUT − (fLO + (3 × fBB))
POUT = 1.05 dBm
POUT = 0.67 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
Rev. 0 | Page 4 of 32
ADL5375-15
Min Typ
Max
Unit
1.01
−3.0
9.8
−14.1
−40.5
−54.2
−0.24
−0.05
−67
0.63
−3.4
10.4
−13.6
−39.0
−51.3
−0.15
−0.08
−73
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−52
−62
dBc
62.7
63.8
dBm
24.6
22.1
dBm
−160.0
−158.2
dBm/Hz
1.05
−2.9
10.0
−14.2
−40.6
−45.0
−0.72
−0.04
−68
0.67
−3.3
10.4
−13.9
−37.9
−44.7
−0.58
−0.06
−62
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−53
−63
dBc
58.7
55.8
dBm
25.7
22.1
dBm
−159.5
−157.9
dBm/Hz
ADL5375
Parameter
LO = 2600 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
LO = 3500 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
ADL5375-05
Min Typ
Max
Conditions
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 1.18 dBm
POUT = 0.78 dBm
POUT − (fLO + (3 × fBB))
POUT = 1.18 dBm
POUT = 0.78 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 1.71 dBm
POUT = 1.14 dBm
POUT − (fLO + (3 × fBB))
POUT = 1.71 dBm
POUT = 1.14 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
Rev. 0 | Page 5 of 32
ADL5375-15
Min Typ
Max
Unit
1.18
−2.8
10.3
−15.1
−41.0
−44.3
−0.72
−0.04
−57
0.78
−3.2
10.6
−14.5
−42.3
−45.6
−0.60
−0.07
−55
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−52
−52
dBc
49.0
48.5
dBm
21.8
19.4
dBm
−159.0
−157.6
dBm/Hz
1.71
−2.3
10.4
−21.6
−30.5
−49.3
−0.20
−0.07
−54
1.14
−2.8
10.1
−20.4
−29.0
−44.9
−0.54
−0.08
−61
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−53
−51
dBc
50.0
57.9
dBm
23.8
19.5
dBm
−157.6
−156.3
dBm/Hz
ADL5375
Parameter
LO = 5800 MHz
Output Power, POUT
Modulator Voltage Gain
Output P1dB
Output Return Loss
Carrier Feedthrough
Sideband Suppression
Quadrature Error
I/Q Amplitude Balance
Second Harmonic
ADL5375-05
ADL5375-15
Third Harmonic
ADL5375-05
ADL5375-15
Output IP2
Output IP3
Noise Floor
LO INPUTS
LO Drive Level
Input Return Loss
BASEBAND INPUTS
I/Q Input Bias Level
Input Bias Current
Input Offset Current
Differential Input
Impedance
Bandwidth (0.1 dB)
OUTPUT DISABLE
Off Isolation
Turn-On Settling Time
Turn-Off Settling Time
DSOP High Level (Logic 1)
DSOP Low Level (Logic 0)
POWER SUPPLIES
Voltage
Supply Current
ADL5375-05
Min Typ
Max
Conditions
VIQ = 1 V p-p differential
RF output divided by baseband input voltage
POUT − (fLO + (2 × fBB))
POUT = 2.40 dBm
POUT = 0.82 dBm
POUT − (fLO + (3 × fBB))
POUT = 2.40 dBm
POUT = 0.82 dBm
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
f1BB = 3.5 MHz, f2BB = 4.5 MHz,
POUT ≈ −5 dBm @ fLO = 900 MHz
I/Q inputs = 0 V differential with a dc bias
only, 20 MHz carrier offset
Characterization performed at typical level
500 MHz < fLO < 3.3 GHz
See Figure 7 and Figure 32 for return loss vs.
frequency
Pin IBBP, Pin IBBN, Pin QBBP, Pin QBBN
−6
Current sourcing from each baseband input
LO = 1900 MHz, baseband input =
500 mV p-p sine wave
Pin DSOP
POUT (DSOP high) – POUT (DSOP low)
DSOP low, LO leakage, LO = 2150 MHz
DSOP high to low (90% of envelope)
DSOP low to high (10% of envelope)
ADL5375-15
Min Typ
Max
Unit
2.40
−1.6
5.7
−11.4
−23.0
−36.0
−1.42
0.20
−57
0.82
−3.2
6.6
−10.5
−16.3
−33.0
+1.17
0.50
−58
dBm
dB
dBm
dB
dBm
dBc
Degrees
dB
dBc
−43
−52
dBc
38.7
35.7
dBm
13.5
12.1
dBm
−153.0
−153.4
dBm/Hz
0
≤−10
+7
−6
0
≤−10
+7
dBm
dB
500
41
0.1
60
1500
32
0.1
100
mV
μA
μA
kΩ
95
80
MHz
86
−53
200
100
85
−53
200
100
dB
dBm
ns
ns
V
V
2.0
2.0
0.8
0.8
Pin VPS1 and Pin VPS2
4.75
DSOP = high
DSOP = low
5.25
200
131
Rev. 0 | Page 6 of 32
4.75
5.25
200
131
V
mA
mA
ADL5375
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
Supply Voltage, VPOS
IBBP, IBBN, QBBP, QBBN
LOIP and LOIN
Internal Power Dissipation
ADL5375-05
ADL5375-15
θJA (Exposed Paddle Soldered Down)1
Maximum Junction Temperature
Operating Temperature Range
Storage Temperature Range
Rating
5.5 V
0 V to 2 V
13 dBm
1500 mW
1200 mW
54°C/W
150°C
−40°C to +85°C
−65°C to +150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
1
Per JDEC standard JESD 51-2. For information on optimizing thermal
impedance, see the Thermal Grounding and Evaluation Board Layout section.
Rev. 0 | Page 7 of 32
ADL5375
24
23
22
21
20
19
VPS2
COMM
IBBN
IBBP
COMM
COMM
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
TOP VIEW
(Not to Scale)
18
17
16
15
14
13
VPS1
COMM
RFOUT
NC
COMM
NC
07052-003
ADL5375
NC 7
COMM 8
QBBN 9
QBBP 10
COMM 11
COMM 12
DSOP 1
COMM 2
LOIP 3
LOIN 4
COMM 5
NC 6
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No.
1
Mnemonic
DSOP
2, 5, 8, 11, 12,
14, 17, 19, 20, 23
3, 4
COMM
LOIP, LOIN
6, 7, 13, 15,
9, 10, 21, 22
NC
QBBN, QBBP,
IBBP, IBBN
16
18, 24
RFOUT
VPS1, VPS2
EP
Description
Output Disable. A logic high on this pin disables the RF output. Connect this pin to ground or leave it
floating to enable the output.
Input Common Pins. Connect to the ground plane via a low impedance path.
Local Oscillator Inputs.
Single-ended operation: The LOIP pin is driven from the LO source through an ac-coupling capacitor
while the LOIN pin is ac-coupled to ground through a capacitor.
Differential operation: The LOIP and LOIN pins must be driven differentially through ac-coupling
capacitors in this mode of operation.
No Connect. These pins can be left open or tied to ground.
Differential In-Phase and Quadrature Baseband Inputs. These high impedance inputs should be
dc-biased to the recommended level depending on the version.
ADL5375-05: 500 mV
ADL5375-15: 1500 mV
These inputs should be driven from a low impedance source. Nominal characterized ac signal swing is
500 mV p-p on each pin. This results in a differential drive of 1 V p-p. These inputs are not self-biased
and have to be externally biased.
RF Output. Single-ended, 50 Ω internally biased RF output. RFOUT must be ac-coupled to the load.
Positive Supply Voltage Pins. All pins should be connected to the same supply (VS). To ensure adequate
external bypassing, connect 0.1 μF and 1000 pF capacitors between each pin and ground.
Exposed Paddle. Connect to the ground plan via a low impedance path.
Rev. 0 | Page 8 of 32
ADL5375
TYPICAL PERFORMANCE CHARACTERISTICS
ADL5375-05
VS = 5 V; TA = 25°C; LO = 0 dBm single-ended drive; baseband I/Q amplitude = 1 V p-p differential sine waves in quadrature with a
500 mV dc bias; baseband I/Q frequency (fBB) = 1 MHz, unless otherwise noted.
12
5
VS = 5.25V
1dB OUTPUT COMPRESSION (dBm)
SSB OUTPUT POWER (dBm)
4
3
TA = –40°C
2
TA = +25°C
1
0
TA = +85°C
–1
–2
–3
VS = 5.0V
10
8
VS = 4.75V
6
4
2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
0
07052-052
–5
0
0.5
1.0
1.5
2.0
2.5
5
SSB OUTPUT POWER (dBm)
3.5
4.0
4.5
5.0
5.5
6.0
Figure 6. SSB Output 1dB Compression Point (OP1dB) vs. LO Frequency (fLO)
and Supply
Figure 3. Single-Sideband (SSB) Output Power (POUT) vs.
LO Frequency (fLO) and Temperature
90
VS = 5.0V
4
3.0
LO FREQUENCY (GHz)
07052-055
–4
VS = 5.25V
60
120
3
VS = 4.75V
2
6G
150
1
30
0
450M
180
–1
–2
0
450M
–3
6G
210
330
–4
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
240
07052-097
S11 OF LO
S22 OF OUTPUT
0
07052-053
–5
300
270
Figure 4. Single-Sideband (SSB) Output Power (POUT) vs.
LO Frequency (fLO) and Supply
Figure 7. Smith Chart of LOIP (LOIN AC-Coupled to Ground) S11 and RFOUT
S22 from 450 MHz to 6000 MHz
12
0
LOIP
10
TA = +85°C
8
–10
RETURN LOSS (dB)
TA = +25°C
6
4
RFOUT
–20
–30
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
LO FREQUENCY (GHz)
4.5
5.0
5.5
6.0
–40
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
FREQUENCY (GHz)
Figure 5. SSB Output 1dB Compression Point (OP1dB) vs. LO Frequency (fLO)
and Temperature
4.5
5.0
5.5
6.0
07052-056
2
07052-054
1dB OUTPUT COMPRESSION (dBm)
TA = –40°C
Figure 8. Return Loss of LOIP (LOIN AC-Coupled to Ground) S11 and RFOUT
S22 from 450 MHz to 6000 MHz
Rev. 0 | Page 9 of 32
ADL5375
ADL5375-05
0
0
–10
–10
–15
TA = +85°C
SIDEBAND SUPPRESSION (dBc)
TA = +25°C
–20
–25
TA = –40°C
–30
–35
–40
–45
–50
–50
–60
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
Figure 12. Sideband Suppression vs. LO Frequency (fLO) and Temperature After
Nulling at 25°C; Multiple Devices Shown
0
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
–20
TA = +85°C
–30
–40
TA = –40°C
–50
TA = +25°C
–60
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
Figure 10. Carrier Feedthrough vs. LO Frequency (fLO) and Temperature After
Nulling at 25°C; Multiple Devices Shown
10
SSB OUTPUT
POWER (dBm)
–10
–20
–30
–40
5
CARRIER
FEEDTHROUGH (dBm)
0
–50
–60
–5
–70
SIDEBAND
SUPPRESSION (dBc)
–80
–10
THIRD-ORDER
DISTORTION (dBc)
–90
–100
0.06
07052-058
–70
SECOND-ORDER
DISTORTION (dBc)
0.1
1
2
BASEBAND INPUT VOLTAGE (V rms)
10
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
0
–20
TA = +85°C
–30
–40
TA = +25°C
–50
–60
TA = –40°C
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
LO FREQUENCY (GHz)
4.5
5.0
5.5
6.0
Figure 11. Sideband Suppression vs. LO Frequency (fLO) and Temperature;
Multiple Devices Shown
–10
SSB OUTPUT
POWER (dBm)
–20
–30
5
CARRIER
FEEDTHROUGH (dBm)
–40
0
–50
–60
–5
SIDEBAND
SUPPRESSION (dBc)
–70
–80
THIRD-ORDER
DISTORTION (dBc)
–90
–100
0.06
07052-059
–70
–15
Figure 13. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. Baseband Differential Input Level
(fLO = 900 MHz)
0
–10
07052-060
2.0
SSB OUTPUT POWER (dBm)
1.5
07052-061
1.0
–10
CARRIER FEEDTHROUGH (dBm)
TA = +85°C
–10
SECOND-ORDER
DISTORTION (dBc)
0.1
1
2
SSB OUTPUT POWER (dBm)
0.5
0
SIDEBAND SUPPRESSION (dBc)
–40
–80
07052-057
0
Figure 9. Carrier Feedthrough vs. LO Frequency (fLO) and Temperature;
Multiple Devices Shown
–80
TA = –40°C
TA = +25°C
LO FREQUENCY (GHz)
–80
–30
–70
–55
–60
–20
–15
BASEBAND INPUT VOLTAGE (V rms)
Figure 14. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. Baseband Differential Input Level
(fLO = 2150 MHz)
Rev. 0 | Page 10 of 32
07052-062
CARRIER FEEDTHROUGH (dBm)
–5
ADL5375
ADL5375-05
5
–30
–40
0
–50
–60
–5
SIDEBAND
SUPPRESSION (dBc)
SECOND-ORDER
DISTORTION (dBc)
–10
–70
–80
–90
THIRD-ORDER
DISTORTION (dBc)
–100
0.06
0.1
2
1
–15
BASEBAND INPUT VOLTAGE (V rms)
Figure 15. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. Baseband Differential Input Level
(fLO = 3500 MHz)
TA = +85°C
16
14
TA = +25°C
12
TA = +85°C
10
8
6
4
2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
TA = –40°C
–50
–60
SECOND-ORDER
–70
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
–40
–0.5
–1.5
SIDEBAND
SUPPRESSION (dBc)
–60
–2.5
SECOND-ORDER
DISTORTION (dBc)
–3.5
100
20
10
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2
BASEBAND FREQUENCY (MHz)
Figure 17. Second-Order Distortion, Carrier Feedthrough, Sideband
Suppression, and SSB POUT vs. Baseband Frequency (fBB); fLO = 2140 MHz
SSB OUTPUT
POWER (dBm)
–30
1
CARRIER
FEEDTHROUGH (dBm)
–40
0
–50
–1
THIRD-ORDER
DISTORTION (dBc)
SIDEBAND
SUPPRESSION (dBc)
–60
–2
SECOND-ORDER
DISTORTION (dBc)
–70
–80
07052-098
10
TA = +85°C
–20
1.5
0.5
30
Figure 19. OIP2 vs. LO Frequency (fLO) and Temperature (POUT ≈ −5 dBm @
fLO = 900 MHz)
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
CARRIER
FEEDTHROUGH (dBm)
TA = +25°C
40
LO FREQUENCY (GHz)
SSB OUTPUT POWER (dBm)
–30
TA = –40°C
50
0
Figure 16. Second- and Third-Order Distortion vs. LO Frequency (fLO) and
Temperature (Baseband I/Q Amplitude = 1 V p-p Differential)
SSB OUTPUT POWER (dBm)
60
–6
–4
–2
0
2
SSB OUTPUT POWER (dBm)
THIRD-ORDER
70
–3
4
6
–4
LO AMPLITUDE (dBm)
Figure 20. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. LO Amplitude (fLO = 900 MHz)
Rev. 0 | Page 11 of 32
07052-065
–40
LO FREQUENCY (GHz)
SECOND-ORDER DISTORTION,
CARRIER FEEDTHROUGH,
SIDEBAND SUPPRESSION
TA = –40°C
18
07052-088
OUTPUT SECOND-ORDER INTERCEPT (dBm)
–30
1
20
LO FREQUENCY (GHz)
07052-064
SECOND-ORDER DISTORTION AND
THIRD-ORDER DISTORTION (dBc)
TA = +25°C
–70
22
80
–20
–50
24
Figure 18. OIP3 vs. LO Frequency (fLO) and Temperature (POUT ≈ −5 dBm @
fLO = 900 MHz)
–10
–20
26
0
0
–80
28
07052-087
CARRIER
FEEDTHROUGH (dBm)
–20
OUTPUT THIRD-ORDER INTERCEPT (dBm)
–10
SSB OUTPUT POWER (dBm)
SSB OUTPUT
POWER (dBm)
07052-063
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
30
10
0
ADL5375
ADL5375-05
230
2
SSB OUTPUT
POWER (dBm)
225
1
0
–50
–1
SIDEBAND
SUPPRESSION (dBc)
–2
THIRD-ORDER
DISTORTION (dBc)
–70
–6
–4
–2
0
205
195
2
4
6
–4
180
–1
–50
–2
–60
–70
–4
–2
12
2
4
8
4
SECOND-ORDER
DISTORTION (dBc)
0
10
6
–3
THIRD-ORDER
DISTORTION (dBc)
–6
14
QUANTITY
SIDEBAND
SUPPRESSION (dBc)
SSB OUTPUT POWER (dBm)
0
85
16
1
–30
25
18
2
6
–4
07052-067
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
SSB OUTPUT
POWER (dBm)
–40
Figure 23. Power Supply Current vs. Temperature
2
–10
–40
VS = 4.75V
TEMPERATURE (°C)
Figure 21. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. LO Amplitude (fLO = 2150 MHz)
CARRIER
FEEDTHROUGH (dBm)
VS = 5.0V
200
185
LO AMPLITUDE (dBm)
–20
VS = 5.25V
210
190
–3
SECOND-ORDER
DISTORTION (dBc)
–80
215
LO AMPLITUDE (dBm)
Figure 22. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. LO Amplitude (fLO = 3500 MHz)
Rev. 0 | Page 12 of 32
0
–160.5 –160.3 –160.1 –159.9 –159.7 –159.5 –159.3 –159.1
NOISE (dBm/Hz)
07052-089
–60
SUPPLY CURRENT (mA)
–40
220
SSB OUTPUT POWER (dBm)
CARRIER
FEEDTHROUGH (dBm)
07052-068
–30
07052-066
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
–20
Figure 24. 20 MHz Offset Noise Floor Distribution at fLO = 900 MHz
(I/Q Amplitude = 0 mV p-p with 500 mV DC Bias)
ADL5375
ADL5375-05
88
QUANTITY
6
5
4
3
2
0
–160.5
–160.1
–159.7
–159.3
–158.9
–158.5
NOISE (dBm/Hz)
9
8
QUANTITY
7
6
5
4
3
2
–158.1
–157.7
–157.3
NOISE (dBm/Hz)
–156.9
–156.5
07052-099
1
–158.5
84
–30
82
–40
–50
80
CARRIER FEEDTHROUGH (dBm)
78
–60
76
–70
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
–80
6.0
LO FREQUENCY (GHz)
10
–158.9
–20
Figure 27. SSB POUT Isolation and Carrier Feedthrough with DSOP High
Figure 25. 20 MHz Offset Noise Floor Distribution at fLO = 2140 MHz
(I/Q Amplitude = 0 mV p-p with 500 mV DC Bias)
0
86
74
07052-090
1
–10
SSB OUTPUT POWER ISOLATION (dB)
CARRIER FEEDTHROUGH (dBm)
7
0
Figure 26. 20 MHz Offset Noise Floor Distribution at fLO = 3500 MHz
(I/Q Amplitude = 0 mV p-p with 500 mV DC Bias)
Rev. 0 | Page 13 of 32
07052-091
90
SSB OUTPUT POWER ISOLATION (dB)
8
ADL5375
ADL5375-15
VS = 5 V; TA = 25°C; LO = 0 dBm single-ended drive; baseband I/Q amplitude = 1 V p-p differential sine waves in quadrature with a
1500 mV dc bias; baseband I/Q frequency (fBB) = 1 MHz, unless otherwise noted.
12
5
VS = 5.25V
1dB OUTPUT COMPRESSION (dBm)
SSB OUTPUT POWER (dBm)
4
3
2
TA = –40°C
TA = +25°C
1
0
TA = +85°C
–1
–2
–3
VS = 5.0V
10
VS = 4.75V
8
6
4
2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
0
07052-069
–5
Figure 28. Single-Sideband (SSB) Output Power (POUT) vs. LO Frequency (fLO)
and Temperature
0
0.5
1.0
1.5
2.0
2.5
4.0
4.5
5.0
5.5
6.0
90
4
60
120
VS = 5.25V
3
2
6G
150
VS = 5.0V
0
450M
180
–1
0
450M
–2
6G
210
–3
–4
330
S11 OF LO
S22 OF OUTPUT
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
240
07052-070
–5
30
VS = 4.75V
1
Figure 29. Single-Sideband (SSB) Output Power (POUT) vs. LO Frequency
(fLO) and Supply
300
07052-102
270
Figure 32. Smith Chart of LOIP (LOIN AC-Coupled to Ground) S11 and RFOUT
S22 from 450 MHz to 6000 MHz
0
12
TA = –40°C
10
–10
RETURN LOSS (dB)
TA = +25°C
8
TA = +85°C
6
4
LOIP
–20
RFOUT
–30
2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
LO FREQUENCY (GHz)
4.5
5.0
5.5
6.0
–40
07052-071
0
Figure 30. SSB Output 1dB Compression Point (OP1dB) vs. LO Frequency (fLO)
and Temperature
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
FREQUENCY (GHz)
4.5
5.0
5.5
6.0
07052-073
SSB OUTPUT POWER (dBm)
3.5
Figure 31. SSB Output 1dB Compression Point (OP1dB) vs. LO Frequency (fLO)
and Supply
5
1dB OUTPUT COMPRESSION (dBm)
3.0
LO FREQUENCY (GHz)
07052-072
–4
Figure 33. Return Loss of LOIP (LOIN AC-Coupled to Ground) S11 and RFOUT
S22 from 450 MHz to 6000 MHz
Rev. 0 | Page 14 of 32
ADL5375
ADL5375-15
0
0
–10
–10
SIDEBAND SUPPRESSION (dBc)
TA = +85°C
–15
–20
–25
TA = –40°C
–30
–35
TA = +25°C
–40
–45
–50
–50
–60
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
–80
TA = +25°C
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
Figure 37. Sideband Suppression vs. LO Frequency (fLO) and Temperature After
Nulling at 25°C; Multiple Devices Shown
0
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
0
–10
–20
–30
TA = +85°C
–40
–50
TA = +25°C
–60
TA = –40°C
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
Figure 35. Carrier Feedthrough vs. LO Frequency (fLO) and Temperature After
Nulling at 25°C; Multiple Devices Shown
10
SSB OUTPUT
POWER (dBm)
–10
–20
–30
–40
5
CARRIER
FEEDTHROUGH (dBm)
SIDEBAND
SUPPRESSION (dBc)
0
–50
–60
–5
–70
SECOND-ORDER
DISTORTION (dBc)
–80
–10
THIRD-ORDER
DISTORTION (dBc)
–90
–100
0.06
07052-075
–70
07052-077
1.0
Figure 34. Carrier Feedthrough vs. LO Frequency (fLO) and Temperature;
Multiple Devices Shown
CARRIER FEEDTHROUGH (dBm)
TA = +85°C
–40
SSB OUTPUT POWER (dBm)
0.5
07052-074
0
LO FREQUENCY (GHz)
–80
–30
–70
–55
–60
TA = –40°C
–20
0.1
1
2
–15
07052-078
CARRIER FEEDTHROUGH (dBm)
–5
BASEBAND INPUT VOLTAGE (V rms)
Figure 38. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. Baseband Differential Input Level
(fLO = 900 MHz)
0
–30
TA = –40°C
TA = +25°C
–40
–50
–60
–80
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
LO FREQUENCY (GHz)
4.5
5.0
5.5
6.0
07052-076
–70
Figure 36. Sideband Suppression vs. LO Frequency (fLO) and Temperature;
Multiple Devices Shown
–10
CARRIER
FEEDTHROUGH (dBm)
–20
–30
5
SIDEBAND
SUPPRESSION (dBc)
–40
0
–50
–60
–5
SECOND-ORDER
DISTORTION (dBc)
–70
THIRD-ORDER
DISTORTION (dBc)
–80
–10
SSB OUTPUT POWER (dBm)
TA = +85°C
10
SSB OUTPUT
POWER (dBm)
–90
–100
0.06
0.1
1
2
–15
BASEBAND INPUT VOLTAGE (V rms)
Figure 39. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. Baseband Differential Input Level
(fLO = 2150 MHz)
Rev. 0 | Page 15 of 32
07052-079
SIDEBAND SUPPRESSION (dBc)
–20
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
0
–10
ADL5375
ADL5375-15
–50
–60
–5
SECOND-ORDER
DISTORTION (dBc)
–70
THIRD-ORDER
DISTORTION (dBc)
–80
–10
–90
–100
0.06
0.1
1
2
–15
BASEBAND INPUT VOLTAGE (V rms)
–20
–30
THIRD-ORDER
–60
–80
TA = +85°C
TA = –40°C
–70
SECOND-ORDER
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
LO FREQUENCY (GHz)
–0.5
–50
–1.5
CARRIER
FEEDTHROUGH (dBm)
–60
–2.5
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
–40
SECOND-ORDER
DISTORTION (dBc)
1
10
–3.5
100
6
4
2
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
80
70
60
TA = –40°C
50
40
TA = +25°C
30
TA = +85°C
20
10
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
2
BASEBAND FREQUENCY (MHz)
Figure 42. Second-Order Distortion, Carrier Feedthrough, Sideband
Suppression, and SSB POUT vs. Baseband Frequency (fBB); fLO = 2140 MHz
SSB OUTPUT
POWER (dBm)
–30
1
CARRIER
FEEDTHROUGH (dBm)
–40
0
–50
–60
–1
SIDEBAND
SUPPRESSION (dBc)
SECOND-ORDER
DISTORTION (dBc)
–2
THIRD-ORDER
DISTORTION (dBc)
–70
–80
07052-103
–70
TA = +85°C
8
–20
SSB OUTPUT POWER (dBm)
SECOND-ORDER DISTORTION,
CARRIER FEEDTHROUGH,
SIDEBAND SUPPRESSION
SIDEBAND
SUPPRESSION (dBc)
10
Figure 44. OIP3 vs. LO Frequency (fLO) and Temperature (POUT ≈ −5 dBm @
fLO = 900 MHz)
1.5
0.5
TA = +25°C
12
LO FREQUENCY (GHz)
SSB OUTPUT POWER (dBm)
–30
14
0
Figure 41. Second- and Third-Order Distortion vs. LO Frequency (fLO) and
Temperature (Baseband I/Q Amplitude = 1 V p-p Differential)
–20
16
LO FREQUENCY (GHz)
07052-081
SECOND-ORDER DISTORTION AND
THIRD-ORDER DISTORTION (dBc)
–10
–50
TA = –40°C
18
0
OUTPUT SECOND-ORDER INTERCEPT (dBm)
0
TA = +25°C
20
Figure 43. OIP3 vs. LO Frequency (fLO) and Temperature (POUT ≈ −5 dBm @
fLO = 900 MHz)
Figure 40. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. Baseband Differential Input Level
(fLO = 3500 MHz)
–40
22
07052-092
0
24
07052-093
SIDEBAND
SUPPRESSION (dBc)
26
SSB OUTPUT POWER (dBm)
–40
5
28
–3
–6
–4
–2
0
2
4
6
–4
LO AMPLITUDE (dBm)
Figure 45. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. LO Amplitude (fLO = 900 MHz)
Rev. 0 | Page 16 of 32
07052-082
–20
OUTPUT THIRD-ORDER INTERCEPT (dBm)
CARRIER
FEEDTHROUGH (dBm)
SSB OUTPUT POWER (dBm)
–10
–30
30
10
SSB OUTPUT
POWER (dBm)
07052-080
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
0
ADL5375
ADL5375-15
2
225
–40
0
–50
–1
SECOND-ORDER
DISTORTION (dBc)
SIDEBAND
SUPPRESSION (dBc)
–60
–2
THIRD-ORDER
DISTORTION (dBc)
–70
–6
–4
–2
0
2
4
220
SUPPLY CURRENT (mA)
1
SSB OUTPUT POWER (dBm)
–30
210
200
185
6
–4
180
25
85
TEMPERATURE (°C)
18
2
SSB OUTPUT
POWER (dBm)
–40
Figure 48. Power Supply Current vs. Temperature
16
1
–30
0
SIDEBAND
SUPPRESSION (dBc)
–40
–1
–50
–2
THIRD-ORDER
DISTORTION (dBc)
–60
14
12
QUANTITY
CARRIER
FEEDTHROUGH (dBm)
SSB OUTPUT POWER (dBm)
–20
10
8
6
4
–3
2
SECOND-ORDER
DISTORTION (dBc)
–6
–4
–2
0
2
4
6
–4
07052-084
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
VS = 4.75V
195
Figure 46. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. LO Amplitude (fLO = 2150 MHz)
–70
VS = 5.0V
205
190
–3
LO AMPLITUDE (dBm)
–10
VS = 5.25V
215
LO AMPLITUDE (dBm)
Figure 47. Second- and Third-Order Distortion, Carrier Feedthrough,
Sideband Suppression, and SSB POUT vs. LO Amplitude (fLO = 3500 MHz)
Rev. 0 | Page 17 of 32
0
–158.0 –157.8 –157.6 –157.4 –157.2 –157.0 –156.8 –156.6
NOISE (dBm/Hz)
07052-094
–80
230
SSB OUTPUT
POWER (dBm)
07052-085
CARRIER
FEEDTHROUGH (dBm)
07052-083
SECOND-ORDER DISTORTION, THIRD-ORDER
DISTORTION, CARRIER FEEDTHROUGH,
AND SIDEBAND SUPPRESSION (dBc)
–20
Figure 49. 20 MHz Offset Noise Floor Distribution at fLO = 900 MHz
(I/Q Amplitude = 0 mV p-p with 1500 mV DC Bias)
ADL5375
ADL5375-15
QUANTITY
8
6
4
2
NOISE (dBm/Hz)
8
7
QUANTITY
6
5
4
3
2
–156.3
NOISE (dBm/Hz)
–155.9
–155.5
07052-104
1
–156.7
–20
84
–30
82
–40
–50
80
CARRIER FEEDTHROUGH (dBm)
78
–60
76
–70
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
–80
6.0
Figure 52. SSB POUT Isolation and Carrier Feedthrough with DSOP High
9
–157.1
86
LO FREQUENCY (GHz)
Figure 50. 20 MHz Offset Noise Floor Distribution at fLO = 2140 MHz
(I/Q Amplitude = 0 mV p-p with 1500 mV DC Bias)
–157.5
SSB OUTPUT POWER ISOLATION (dB)
74
07052-095
0
–158.5 –158.3 –158.1 –157.9 –157.7 –157.5 –157.3 –157.1
–10
88
CARRIER FEEDTHROUGH (dBm)
SSB OUTPUT POWER ISOLATION (dB)
10
0
0
90
Figure 51. 20 MHz Offset Noise Floor Distribution at fLO = 3500 MHz
(I/Q Amplitude = 0 mV p-p with 500 mV DC Bias)
Rev. 0 | Page 18 of 32
07052-096
12
ADL5375
THEORY OF OPERATION
CIRCUIT DESCRIPTION
V-to-I Converter
The ADL5375 can be divided into five circuit blocks: the LO
interface, the baseband voltage-to-current (V-to-I) converter,
the mixers, the differential-to-single-ended (D-to-S) stage,
and the bias circuit. A block diagram of the device is shown in
Figure 53.
The differential baseband inputs (QBBP, QBBN, IBBN, and
IBBP) present a high impedance. The voltages applied to these
pins drive the V-to-I stage that converts baseband voltages into
currents. The differential output currents of the V-to-I stages
feed each of their respective mixers. The dc common-mode
voltage at the baseband inputs sets the currents in the two
mixer cores. Varying the baseband common-mode voltage
influences the current in the mixer and affects overall modulator performance. The recommended dc voltage for the baseband
common-mode voltage is 500 mV dc for the ADL5375-05 and
1500 mV for the ADL5375-15.
LOIP
LOIN
PHASE
SPLITTER
IBBP
IBBN
QBBP
Mixers
RFOUT
DSOP
QBBN
07052-028
Σ
Figure 53. Block Diagram
The LO interface generates two LO signals in quadrature.
These signals are used to drive the mixers. The I/Q baseband
input signals are converted to currents by the V-to-I stages,
which then drive the two mixers. The outputs of these mixers
combine to feed the output balun, which provides a singleended output. The bias cell generates reference currents for
the V-to-I stage.
LO Interface
The ADL5375 has two double-balanced mixers: one for the
in-phase channel (I channel) and one for the quadrature channel (Q-channel). The output currents from the two mixers sum
together into an internal load. The signal developed across this
load is used to drive the D-to-S stage.
D-to-S Stage
The output D-to-S stage consists of an on-chip active balun
that converts the differential signal to a single-ended signal.
The balun presents 50 Ω impedance to the output (VOUT).
Therefore, no matching network is needed at the RF output
for optimal power transfer in a 50 Ω environment.
Bias Circuit
The LO interface consists of a polyphase quadrature splitter
and a limiting amplifier. The LO input impedance is set by
the polyphase splitter. Each quadrature LO signal then passes
through a limiting amplifier that provides the mixer with a
limited drive signal.
The LO input can be driven single-ended or differentially.
For applications above 3 GHz, improved OIP2 and LO leakage
may result from driving the LO input differentially.
An on-chip band gap reference circuit is used to generate a
proportional-to-absolute temperature (PTAT) reference current
for the V-to-I stage.
DSOP
The DSOP pin can be used to disable the output stage of the
modulator. If the DSOP pin is connected to ground or left
unconnected, the part operates normally. If the DSOP pin is
connected to the positive voltage supply, the output stage is
disabled and the LO leakage is also reduced.
Rev. 0 | Page 19 of 32
ADL5375
BASIC CONNECTIONS
COMM
19
IBBP
IBBN
COMM
COMM
20
21
24
B
C7
1000pF
COMM
16
4
15
5
14
EXPOSED PADDLE
QBBN
8
6
NC 7
COMM
NC
3
17
13
VPS1
C4
0.1µF
VPOS
COMM
RFOUT
NC
COMM
RFOUT
C1
1000pF
NC
12
LOIN
18
Z1
ADL5375
2
C2
1000pF
COMM
LOIP
1
11
LOIP
COMM
10
C6
1000pF
COMM
DSOP
QBBP
S1
9
A
C3
1000pF
22
C5
0.1µF
VPOS
23
VPOS
IBBP
VPS2
IBBN
QBBN
QBBP
07052-029
GND
Figure 54. Basic Connections for the ADL5375
Figure 54 shows the basic connections for the ADL5375.
POWER SUPPLY AND GROUNDING
Pin VPS1 and Pin VPS2 should be connected to the same 5 V
source. Each pin should be decoupled with a 100 pF and
0.1 μF capacitor. These capacitors should be located as close
as possible to the device. The power supply can range between
4.75 V and 5.25 V.
The ten COMM pins should be tied to the same ground plane
through low impedance paths.
The exposed paddle on the underside of the package should also
be soldered to a ground plane with low thermal and electrical
impedance. If the ground plane spans multiple layers on the
circuit board, they should be stitched together with nine vias
under the exposed paddle as illustrated in the Evaluation Board
section. The AN-772 application note discusses the thermal and
electrical grounding of the LFCSP (QFN) package in detail.
All the baseband inputs must be externally dc biased. The
recommended common-mode level is dependent on the
version of the ADL5375.
•
ADL5375-05: 500 mV
•
ADL5375-15: 1500 mV
LO INPUT
The LO input is designed to be driven from a single-ended
source. The LO source is ac-coupled through a series capacitor
to the LOIP pin while the LOIN pin is ac-coupled to ground
through a second capacitor.
The typical LO drive level, which was used for the
characterization of the ADL5375, is 0 dBm.
Differential operation is also possible, in which case both sides
of the differential LO source should be ac-coupled through a
pair of series capacitors to the LOIP and LOIN pins.
BASEBAND INPUTS
RF OUTPUT
The baseband inputs (IBBP, IBBN, QBBP, and QBBN) should be
driven from a differential source. The nominal drive level used
in the characterization of the ADL5375 is 1 V p-p differential
(or 500 mV p-p on each pin).
The RF output is available at the RFOUT pin (Pin 16), which can
drive a 50 Ω load. The internal balun provides a low dc path to
ground. In most situations, the RFOUT pin must be ac-coupled
to the load.
Rev. 0 | Page 20 of 32
ADL5375
OUTPUT DISABLE
The ADL5375 incorporates an output disable pin feature that
shuts down the output amplifier stage to isolate the modulator
from the load. This feature is enabled (output is disabled) when
the voltage on the DSOP exceeds 2 V. The feature is disabled
(output not enabled) when the DSOP pin is either tied to
ground or left unconnected.
to just above the KT (thermal) noise level. Asserting DSOP also
reduces the supply current of the ADL5375 from 200 mA to
131 mA.
The time delay between when the DSOP pin is forced to ground
and the output power is restored is approximately 200 ns. The
time delay between when the DSOP pin is forced to the positive
supply voltage and the output shuts off is under 100 ns.
Asserting DSOP further reduces LO leakage (see Figure 27 and
Figure 52) and drives the broadband noise of the device down
Rev. 0 | Page 21 of 32
ADL5375
OPTIMIZATION
The carrier feedthrough and sideband suppression performance of
the ADL5375 can be improved by using optimization techniques.
The same applies to the Q-channel. For the ADL5375-15, the
same theory applies except that
Carrier Feedthrough Nulling
VIBBP = VIBBN = 1500 mV.
Carrier feedthrough results from minute dc offsets that occur
between each of the differential baseband inputs. In an ideal
modulator, the quantities (VIBBP − VIBBN) and (VQBBP − VQBBN)
are equal to zero, which results in no carrier feedthrough. In a real
modulator, those two quantities are nonzero and, when mixed
with the LO, result in a finite amount of carrier feedthrough. The
ADL5375 is designed to provide a minimal amount of carrier
feedthrough. Should even lower carrier feedthrough levels be
required, minor adjustments can be made to the (VIBBP − VIBBN)
and (VQBBP − V QBBN) offsets. The I-channel offset is held constant,
while the Q-channel offset is varied until a minimum carrier
feedthrough level is obtained. The Q-channel offset required to
achieve this minimum is held constant, while the offset on the
I-channel is adjusted until a new minimum is reached. Through
two iterations of this process, the carrier feedthrough can be
reduced to as low as the output noise. The ability to null is
sometimes limited by the resolution of the offset adjustment.
Figure 55 illustrates the typical relationship between carrier
feedthrough and dc offset around the null.
It is often desirable to perform a one-time carrier null calibration. This is usually performed at a given frequency and the
radio allowed to operate over a frequency range on each side
of that frequency. The nulled carrier feedthrough level degrades
somewhat as the LO frequency is moved away from the
frequency at which the null was performed. This variation is
very small across a 30 MHz or 60 MHz cellular band, however.
This small variation is due to the effects of LO-to-RF output
leakage around the package and on the board as the frequency
changes. Despite the degradation, the LO leakage can be
expected to be better than when no nulling is performed.
Sideband Suppression Optimization
Sideband suppression results from relative gain and relative
phase offsets between the I-channel and Q-channel and can
be suppressed through adjustments to those two parameters.
Figure 56 illustrates how sideband suppression is affected by
the gain and phase imbalances.
0
–10
SIDEBAND SUPPRESSION (dBc)
–60
–68
–72
–76
–80
2.5dB
–20 1.25dB
–30 0.5dB
0.25dB
–40 0.125dB
–50 0.05dB
0.025dB
–60 0.0125dB
–70
0dB
–80
–84
–90
0.01
–60
0
60
120
180
240
300
VP – VN OFFSET (µV)
0.1
1
10
100
PHASE ERROR (Degrees)
07052-030
–88
–300 –240 –180 –120
07052-032
CARRIER FEEDTHROUGH (dBm)
–64
Figure 56. Sideband Suppression vs. Quadrature Phase Error for
Various Quadrature Amplitude Offsets
Figure 55. Example of Typical Carrier Feedthrough vs. DC Offset Voltage
Using the ADL5375-05 version as an example, note that
throughout the nulling process, the dc bias for the baseband inputs remains at 500 mV. When no offset is applied,
VIBBP = VIBBN = 500 mV, or
VIBBP − VIBBN = VIOS = 0 V
When an offset of +VIOS is applied to the I-channel inputs,
VIBBP = 500 mV + VIOS/2, and
VIBBN = 500 mV − VIOS/2, such that
VIBBP − VIBBN = VIOS
Figure 56 underlines the fact that adjusting only one parameter
improves the sideband suppression only to a point, unless the
other parameter is also adjusted. For example, if the amplitude
offset is 0.25 dB, improving the phase imbalance by better than
1° does not yield any improvement in the sideband suppression.
For optimum sideband suppression, an iterative adjustment
between phase and amplitude is required.
The sideband suppression nulling can be performed either
through adjusting the gain for each channel or through the
modification of the phase and gain of the digital data coming
from the baseband signal processor.
Rev. 0 | Page 22 of 32
ADL5375
APPLICATIONS INFORMATION
AD9779
Driving the ADL5375-05 with a TXDAC®
OUT1_P
OUT1_N
OUT2_N
An example of an interface using the AD9779 TxDAC is shown
in Figure 57. The baseband inputs of the ADL5375-05 require
a dc bias of 500 mV. The average output current on each of the
outputs of the AD9779 is 10 mA. Therefore, a single 50 Ω resistor to ground from each of the DAC outputs results in an average
current of 10 mA flowing through each of the resistors, thus
producing the desired 500 mV dc bias for the inputs to the
ADL5375-05.
21
IBBP
OUT2_P
OUT2_P
84
RBQN
50Ω
RBQP
50Ω
83
84
9
RBQN
50Ω
RBQP
50Ω
83
IBBN
QBBN
RSLQ
100Ω
10
QBBP
The value of this ac voltage swing limiting resistor is chosen
based on the desired ac voltage swing. Figure 59 shows the
relationship between the swing-limiting resistor and the peakto-peak ac swing that it produces when 50 Ω bias-setting
resistors are used.
1.8
22
9
10
IBBN
QBBN
QBBP
DIFFERENTIAL SWING (V p-p)
OUT2_N
22
2.0
07052-033
OUT1_N
RBIN
50Ω
RSLI
100Ω
RBIN
50Ω
Figure 58. AC Voltage Swing Reduction Through the Introduction
of a Shunt Resistor Between Differential Pair
RBIP
50Ω
92
92
IBBP
Figure 57. Interface Between the AD9779 and ADL5375-05 with 50 Ω
Resistors to Ground to Establish the 500 mV DC Bias for the ADL5375-05
Baseband Inputs
The AD9779 output currents have a swing that ranges from 0 mA
to 20 mA. With the 50 Ω resistors in place, the ac voltage swing
going into the ADL5375-05 baseband inputs ranges from 0 V to
1 V. A full-scale sine wave out of the AD9779 can be described
as a 1 V p-p single-ended (or 2 V p-p differential) sine wave
with a 500 mV dc bias.
Limiting the AC Swing
There are situations in which it is desirable to reduce the ac
voltage swing for a given DAC output current. This can be
achieved through the addition of another resistor to the interface.
This resistor is placed in the shunt between each side of the
differential pair, as shown in Figure 58. It has the effect of
reducing the ac swing without changing the dc bias already
established by the 50 Ω resistors.
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
10
100
1000
RL (Ω)
10000
07052-035
OUT1_P
ADL5375-05
93
21
RBIP
50Ω
The ADL5375-05 is designed to interface with minimal
components to members of the Analog Devices, Inc. TxDAC
families. These dual-channel differential current output DACs
feature an output current swing from 0 mA to 20 mA. The
interface described in this section can be used with any DAC
that has a similar output.
AD9779
ADL5375-05
93
07052-034
DAC MODULATOR INTERFACING
Figure 59. Relationship Between the AC Swing-Limiting Resistor and the
Peak-to-Peak Voltage Swing with 50 Ω Bias-Setting Resistors
Filtering
It is necessary to place an antialiasing filter between the DAC
and modulator to filter out Nyquist images and broadband
DAC noise. The interface for setting up the biasing and ac
swing discussed in the Limiting the AC Swing section lends
itself well to the introduction of such a filter. The filter can be
inserted between the dc bias setting resistors and the ac swinglimiting resistor. Doing so establishes the input and output
impedances for the filter.
Figure 60 shows a third-order, Bessel low-pass filter with a 3 dB
frequency of 10 MHz. Matching input and output impedances
make the filter design easier, so the shunt resistor chosen is
100 Ω, producing an ac swing of 1 V p-p differential. The
frequency response of this filter is shown in Figure 61.
Rev. 0 | Page 23 of 32
ADL5375
OUT1_N
OUT2_N
RBIN
92 50Ω
RBIP
45.3Ω
350.1pF
C2I
22
LNQ
771.1nH
84
RBQP
83 50Ω
53.62nF
C1Q
350.1pF
C2Q
OUT1_P
IBBP
9
IBBN
OUT1_N
QBBN
OUT2_N
10
LPQ
771.1nH
0
QBBP
OUT2_P
–20
24
GROUP DELAY
–30
18
–40
12
–50
6
GROUP DELAY (ns)
30
22
9
RLQN
3480Ω
RSQP
1kΩ
IBBN
QBBN
5V
RLQP
3480Ω
10
QBBP
0
100
USING THE AD9779 AUXILIARY DAC FOR CARRIER
FEEDTHROUGH NULLING
07052-037
MAGNITUDE (dB)
5V
RLIN
3480Ω
The active level shifting circuit involves the use of the ADA4938
dual-differential amplifier. This device has a VOCM pin that
sets the output dc bias. Through this pin, the output commonmode of the amplifier can be easily set to the requisite 1.5 V for
biasing the ADL5375-15 baseband inputs.
MAGNITUDE
–10
10
RBQP
45.3Ω
IBBP
Figure 62. Passive Level-Shifting Network For Biasing ADL5375-15
from TxDAC
36
1
RSIP
1kΩ
RSQN
1kΩ
84
83
21
RLIP
3480Ω
RBQN
45.3Ω
Figure 60. DAC Modulator Interface with
10 MHz Third-Order, Bessel Filter
–60
RBIN
45.3Ω
92
RSLQ
100Ω
ADL5375-15
RSIN
1kΩ
93
RSLI
100Ω
LNI
771.1nH
RBQN
50Ω
OUT2_P
53.62nF
C1I
AD9779
07052-086
RBIP
50Ω
21
FREQUENCY (MHz)
Figure 61. Frequency Response for DAC Modulator Interface with
10 MHz Third-Orde,r Bessel Filter
The AD9779 features an auxiliary DAC that can be used to
inject small currents into the differential outputs for each
main DAC channel. This feature can be used to produce the
small offset voltages necessary to null out the carrier feedthrough from the modulator. Figure 63 shows the interface
required to use the auxiliary DACs, which adds four resistors
to the interface.
90
AUX1_P
Driving the ADL5375-15 with a TXDAC
AD9779
The ADL5375-15 requires a 1500 mV dc bias and therefore
requires a slightly more complex interface that performs a dc
level shift on the baseband signals. It is necessary to level-shift
the DAC output from a 500 mV dc bias to the 1500 mV dc bias
that the ADL5375-15 requires.
Level-shifting can be achieved with either a passive network
or an active circuit. A passive network of resistors is shown
in Figure 62. In this network, the dc bias of the DAC remains
at 500 mV while the input to the ADL5375-15 is 1500 mV.
It should be noted that this passive level-shifting network
introduces approximately 2 dB of loss in the ac signal.
OUT1_P
OUT1_N
AUX1_N
500Ω
250Ω
93
RBIP
50Ω
RBIN
92 50Ω
ADL5375-05
LPI
771.1nH
53.62nF
C1I
350.1pF
C2I
250Ω
LNI
771.1nH
21
IBBP
RSLI
100Ω
22
IBBN
89
500Ω
AUX2_N
87
500Ω
OUT2_N
RBQN
50Ω
OUT2_P
AUX2_P
250Ω
84
RBQP
83 50Ω
86
LNQ
771.1nH
53.62nF
C1Q
350.1pF
C2Q
250Ω
LPQ
771.1nH
9
QBBN
RSLQ
100Ω
10
QBBP
500Ω
Figure 63. DAC Modulator Interface with Auxiliary DAC Resistors
Rev. 0 | Page 24 of 32
07052-038
OUT1_P
ADL5375-05
LPI
771.1nH
93
07052-036
AD9779
ADL5375
–60
Figure 64 illustrates the 6 MHz offset noise of the ADL5375-05
and the ADL5375-15 vs. output power at 940 MHz. Figure 65
demonstrates how the 6 MHz offset noise is affected by variations in LO drive level for both versions of the ADL5375 at
940 MHz.
–100
–66
–68
ADJACENT CPR
–70
–72
–74
–76
–78
ALTERNATE CPR
–80
–82
–16
–14
–10
–12
–8
–6
–4
OUTPUT POWER (dBm)
–102
Figure 66. ADL5375-05 Single-Carrier W-CDMA Adjacent and Alternate
Channel Power vs. Output Power at 2140 MHz; LO Power = 0 dBm
–103
–58
–105
ADL5375-05
–106
–5
–4
–3
–2
–1
0
OUTPUT POWER (dBm)
Figure 64. GSM/Edge (8-PSK) 6 MHz Offset Noise at 940 MHz vs. Output
Power,
LO Drive = 0 dBm
–101
ADJACENT AND ALTERNATE CHANNEL
POWER RATIOS (dB)
ADL5375-15
–102
–60
–62
–64
–66
–70
–72
–74
–76
–78
ALTERNATE CPR
–80
–82
–20
–103
ADJACENT CPR
–68
–18
–16
–14
–12
–10
–8
–6
–4
OUTPUT POWER (dBm)
–104
07052-110
–104
–107
Figure 67. ADL5375-15 Single-Carrier W-CDMA Adjacent and Alternate
Channel Power vs. Output Power at 2140 MHz; LO Power = 0 dBm
–105
Figure 66 and Figure 67 show that both versions of the ADL5375
are able to deliver about or better than −72 dB ACPR at an
output power of −10 dBm.
–107
ADL5375-05
–108
0
1
2
3
4
LO DRIVE (dBm)
5
6
7
Figure 65. GSM/Edge (8-PSK) 6 MHz Offset Noise at 940 MHz vs. LO Drive,
Output Power = 0 dBm
W-CDMA OPERATION
The ADL5375 is suitable for W-CDMA operation. Figure 66
and Figure 67 show the adjacent and alternate channel power
ratios for the ADL5375-05 and ADL5375-15, respectively, at an
LO frequency of 2140 MHz.
6.0
5.5
COMPOSITE EVM
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
SYMBOL EVM
1.0
0.5
0
–6
–4
–2
0
LO DRIVE (dBm)
2
4
6
07052-100
–109
Figure 68 and Figure 69 illustrate the sensitivity of the EVM to
variations in LO drive at 2140 MHz for the ADL5375-05 and
ADL5375-15 respectively.
COMPOSITE AND SYMBOL EVM (%)
ADL5375-15
–106
07052-105
6MHz OFFSET NOISE FLOOR (dBc/100kHz)
–64
–84
–18
–101
07052-107
6MHz OFFSET NOISE FLOOR (dBc/100kHz)
–99
–62
07052-109
The performance of the ADL5375 in a GSM/EDGE environment is shown in this section.
ADJACENT AND ALTERNATE CHANNEL
POWER RATIOS (dB)
GSM/EDGE OPERATION
Figure 68. ADL5375-05 Single Carrier W-CDMA Composite and Symbol EVM
vs. LO Drive at 2140 MHz; Output Power = −10 dBm
Rev. 0 | Page 25 of 32
ADL5375
6.0
Table 5. ADF4360-x Family Operating Frequencies
COMPOSITE AND SYMBOL EVM (%)
5.5
5.0
Part
ADF4360-0
ADF4360-1
ADF4360-2
ADF4360-3
ADF4360-4
ADF4360-5
ADF4360-6
ADF4360-7
ADF4360-8
COMPOSITE EVM
4.5
4.0
3.5
3.0
2.5
2.0
1.5
SYMBOL EVM
1.0
0.5
–4
–2
0
2
LO DRIVE (dBm)
4
6
TRANSMIT DAC OPTIONS
07052-101
0
–6
Output Frequency Range (MHz)
2400 to 2725
2050 to 2450
1850 to 2150
1600 to 1950
1450 to 1750
1200 to 1400
1050 to 1250
350 to 1800
65 to 400
The EVM exhibits moderate improvements with an increase in
the LO drive.
The AD9779 recommended in the previous sections of this data
sheet is by no means the only DAC that can be used to drive the
ADL5375. There are other appropriate DACs, depending on the
level of performance required. Table 6 lists the dual TxDAC
offered by Analog Devices.
LO GENERATION USING PLLS
Table 6. Dual TxDAC Selection
Analog Devices has a line of PLLs that can be used for generating
the LO signal. Table 4 lists the PLLs together with their maximum
frequency and phase noise performance.
Part
AD9709
AD9761
AD9763
AD9765
AD9767
AD9773
AD9775
AD9777
AD9776
AD9778
AD9779
Figure 69. ADL5375-15 Single Carrier W-CDMA Composite and Symbol EVM
vs. LO Drive at 2140 MHz; Output Power = −10 dBm
Table 4. Analog Devices PLL Selection
Part
ADF4110
ADF4111
ADF4112
ADF4113
ADF4116
ADF4117
ADF4118
Frequency, fIN (MHz)
550
1200
3000
4000
550
1200
3000
Phase Noise @ 1 kHz Offset
and 200 kHz PFD (dBc/Hz)
−91 @ 540 MHz
−87 @ 900 MHz
−90 @ 900 MHz
−91 @ 900 MHz
−89 @ 540 MHz
−87 @ 900 MHz
−90 @ 900 MHz
The ADF4360-x comes as a family of chips with nine operating
frequency ranges. Choose chips depending on the local
oscillator frequency required. While the use of the integrated
synthesizer may come at the expense of slightly degraded noise
performance from the ADL5375, it can be a cheaper alternative
to a separate PLL and VCO solution. Table 5 shows the options
available.
Resolution (Bits)
8
10
10
12
14
12
14
16
12
14
16
Update Rate (MSPS Minimum)
125
40
125
125
125
160
160
160
1000
1000
1000
All DACs listed have nominal bias levels of 0.5 V and use the
same simple DAC modulator interface that is shown in Figure 60.
MODULATOR/DEMODULATOR OPTIONS
Table 7 lists other Analog Devices modulators and demodulators.
Table 7. Modulator/Demodulator Options
Part No.
AD8345
AD8346
AD8349
ADL5390
Modulator/
Demodulator
Modulator
Modulator
Modulator
Modulator
Frequency
Range (MHz)
140 to 1000
800 to 2500
700 to 2700
20 to 2400
ADL5385
ADL5370
ADL5371
ADL5372
ADL5373
ADL5374
AD8347
AD8348
ADL5387
AD8340
AD8341
Modulator
Modulator
Modulator
Modulator
Modulator
Modulator
Demodulator
Demodulator
Demodulator
Vector modulator
Vector modulator
50 to 2200
300 to 1000
500 to 1500
1500 to 2500
2300 to 3000
3000 to 4000
800 to 2700
50 to 1000
50 to 2000
700 to 1000
1500 to 2400
Rev. 0 | Page 26 of 32
Comments
External
quadrature
ADL5375
EVALUATION BOARD
underside for easy removal and replacement of the ADL5375
should it be necessary.
Populated RoHS-compliant evaluation boards are available
for evaluation of both versions of the ADL5375. The ADL5375
package has an exposed paddle on the underside. This exposed
paddle should be soldered to the board for good thermal and
electrical grounding. The evaluation board is designed without
any components on the underside, so heat can be applied to the
Both versions of the ADL5375 share the same evaluation board
and schematic. To differentiate the boards from each other,
the silkscreen on the underside of the board has a table that is
marked to indicate which version (-05 or -15) is populated on
the board.
IBBN
IBBP
R1
0Ω
R2
0Ω
B
R15
49.9Ω
C6
1000pF
LOIP
R6
10kΩ
DSOP
COMM
LOIP
LOIN
C7
R16
OPEN 1000pF
LOIN
COMM
NC
COMM
19
COMM
IBBP
R9
OPEN
20
24
S1
A
IBBN
C3
1000pF
21
C5
0.1µF
22
VPOS
VPS2
VPOS
R7
OPEN
23 COMM
R8
OPEN
1
18
Z1
ADL5375
2
3
17
16
VPS1
5
14
EXPOSED PADDLE
6
C4
0.1µF
VPOS
COMM
RFOUT
15 NC
4
C2
1000pF
COMM
RFOUT
C1
1000pF
13 NC
12
COMM
11
COMM
9
8
10
QBBP
VPOS
QBBN
NC
R5
OPEN
COMM
7
R17
0Ω
GND
R12
OPEN
R3
0Ω
R10
OPEN
R4
0Ω
QBBN
QBBP
07052-047
R11
OPEN
Figure 70. ADL5375 Evaluation Board Schematic
Table 8. Evaluation Board Description and Configuration Options
Component
VPOS, GND Test Points
S1 Switch
Description
Power Supply and Ground test points for clip leads
DSOP Output Disable Select
R1 to R4, R7 to R12
Baseband input filtering components
LOIP SMA, R16, R17
LOIN SMA, R16, R17
Single-ended local oscillator input
Optional SMA for differential LO input
Rev. 0 | Page 27 of 32
Default Condition/Option Settings
Red = 5 V, black = GND
Position A = output enabled
Position B = output disabled
R1 to R4 = 0 Ω (0402)
R7 to R12 = open (0402)
R16 = open, R17 = 0 Ω (0402)
R16 = 0 Ω (0402), R17 = open
ADL5375
Ping Toh
THERMAL GROUNDING AND EVALUATION
BOARD LAYOUT
The package for the ADL5375 features an exposed paddle on
the underside that should be well soldered to a low thermal
and electrical impedance ground plane. This paddle is typically
soldered to an exposed opening in the solder mask on the
evaluation board. Figure 73 illustrates the dimensions used
in the layout of the ADL5735 footprint on the ADL5375
evaluation board (1 mil. = 0.0254 mm).
Notice the use of nine via holes on the exposed paddle. These
ground vias should be connected to all other ground layers on
the evaluation board to maximize heat dissipation from the
device package.
12 mil.
07052-048
25 mil.
23 mil.
Figure 71. Evaluation Board Layout, Top Layer
82 mil.
12 mil.
98.4 mil.
133.8 mil.
07052-046
19.7 mil.
Figure 73. Dimensions for Evaluation Board Layout for the ADL5375 Package
07052-051
Under these conditions, the thermal impedance of the ADL5375
was measured to be approximately 30°C/W in still air.
Figure 72. Evaluation Board Layout, Bottom Layer
Rev. 0 | Page 28 of 32
ADL5375
CHARACTERIZATION SETUP
AEROFLEX IFR 3416
250kHz TO 6GHz SIGNAL GENERATOR
ROHDE & SCHWARTZ
SPECTRUM ANALYZER
FSU 20Hz TO 8GHz
RF
OUT
FREQ 4MHz LEVEL 0dBm
BIAS 0.5V GAIN 0.7V
BIAS 0.5V GAIN 0.7V
LO
CONNECT TO BACK OF UNIT
I OUT I/AM Q OUT Q/FM
90°
I
+6dBm
RF
IN
0°
Q
AGILENT 34401A
MULTIMETER
F-MOD TEST SETUP
0.175 ADC
IP
F-MOD
LO
VPOS +5V
IN
QP
AGILENT E3631A
POWER SUPPLY
OUT
OUTPUT
QN
VPOS GND
0.175A
±25V
6V
+
–
+ COM –
07052-049
5.000
Figure 74. Characterization Bench Setup
The primary setup used to characterize the ADL5375 is shown
in Figure 74. This setup was used to evaluate the product as a
single-sideband modulator. The Aeroflex signal generator supplied
the LO and differential I and Q baseband signals to the device
under test (DUT). The typical LO drive was 0 dBm. The I-channel
is driven by a sine wave, and the Q-channel is driven by a cosine
wave. The lower sideband is the single-sideband (SSB) output.
The majority of characterization for the ADL5375 was performed
using a 1 MHz sine wave signal with a 500 mV (ADL5375-05)
or 1500 mV (ADL5375-15) common-mode voltage applied to
the baseband signals of the DUT. The baseband signal path was
calibrated to ensure that the VIOS and VQOS offsets on the
baseband inputs were minimized as close as possible to 0 V
before connecting to the DUT. See the Carrier Feedthrough
Nulling section for the definitions of VIOS and VQOS.
Rev. 0 | Page 29 of 32
ADL5375
CH1 1MHz
AMPL 700mV p-p
PHASE 0°
CH2 1MHz
AMPL 700mV p-p
PHASE 90°
0°
ROHDE & SCHWARTZ SMT 06
SIGNAL GENERATOR
CH2 OUTPUT
CH1 OUTPUT
TEKTRONIX AFG3252
DUAL FUNCTION
ARBITRARY FUNCTION GENERATOR
I Q
RF
OUT
FREQ 4MHz TO 4GHz
LEVEL 0dBm
LO
90°
SINGLE-TO-DIFFERENTIAL
CIRCUIT BOARD
AGILENT E3631A
POWER SUPPLY
F-MOD TEST RACK
5.000
0.350A
Q IN AC
±25V
6V
VPOS ++5V–
+5V
VPOS +5V
F-MOD
CHAR BD
Q IN DCCM
+ COM –
IP
IP
VPOSB VPOSA IN
IN
TSEN
–5V
GND
AGND IN1
IN1
VN1
VP1
I IN DCCM
I IN AC
QP
LO
OUTPUT
OUT
QN
GND
VPOS
QP
QN
AGILENT E3631A
POWER SUPPLY
ROHDE & SCHWARTZ
FSEA 30 SPECTRUM ANALYZER
0.500
0.010A
+
6V
±25V
–
+ COM –
RF
IN
100MHz TO 4GHz
+6dBm
VCM = 0.5V
AGILENT 34401A
MULTIMETER
07052-050
0.200 ADC
Figure 75. Setup for Baseband Frequency Sweep and Undesired Sideband Nulling
The setup used to evaluate baseband frequency sweep and
undesired sideband nulling of the ADL5375 is shown in Figure 75.
The interface board has circuitry that converts the single-ended
I input and Q input from the arbitrary function generator to
differential I and Q baseband signals with a dc bias of 500 mV
(ADL5375-05) or 1500mV (ADL5375-15). Undesired sideband
nulling was achieved through an iterative process of adjusting
amplitude and phase on the Q-channel. See the Sideband
Suppression Optimization section for a detailed description
on sideband nulling.
Rev. 0 | Page 30 of 32
ADL5375
OUTLINE DIMENSIONS
0.60 MAX
4.00
BSC SQ
PIN 1
INDICATOR
0.60 MAX
TOP
VIEW
0.50
BSC
3.75
BSC SQ
0.50
0.40
0.30
1.00
0.85
0.80
12° MAX
SEATING
PLANE
0.80 MAX
0.65 TYP
0.30
0.23
0.18
PIN 1
INDICATOR
19
18
24 1
2.65
2.50 SQ
2.35
EXPOSED
PAD
(BOTTOMVIEW)
13
12
7
6
0.23 MIN
2.50 REF
0.05 MAX
0.02 NOM
0.20 REF
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-8
Figure 76. 24-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad
(CP-24-3)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADL5375-05ACPZ-R7 1
ADL5375-05ACPZ-WP1
ADL5375-05-EVALZ1
ADL5375-15ACPZ-R71
ADL5375-15ACPZ-WP1
ADL5375-15-EVALZ1
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
24-Lead LFCSP_VQ, 7” Tape and Reel
24-Lead LFCSP_VQ, Waffle Pack
Evaluation Board
24-Lead LFCSP_VQ, 7” Tape and Reel
24-Lead LFCSP_VQ, Waffle Pack
Evaluation Board
Z = RoHS Compliant Part/Evaluation Board.
Rev. 0 | Page 31 of 32
Package Option
CP-24-3
CP-24-3
Ordering Quantity
1,500
64
CP-24-3
CP-24-3
1,500
64
ADL5375
NOTES
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07052-0-12/07(0)
Rev. 0 | Page 32 of 32
Similar pages