Document 560 Flyback Transformers For Silicon Laboratories Si3402 PD Controller • Designed for Power over Ethernet PD controllers for applications up to 10 Watts. • Operates in continuous conduction mode with 36 – 72 V input • 1500 Vrms, one minute isolation between primary and secondary Core material Ferrite Terminations RoHS tin-silver over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 3.8 – 3.9 g Ambient temperature –40°C to +85°C Storage temperature Component: –40°C to +85°C. Tape and reel packaging: –40°C to +80°C Maximum part temperature +125°C (ambient + temp rise) Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 200 per 13″ reel Plastic tape: 32 mm wide, 0.5 mm thick, 24 mm pocket spacing, 11.2 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf. Inductance Part Power at 0 A2 number1 (W) ±10% (µH) FA2671-AL_ FA2672-AL_ FA2732-AL_ 10 10 10 Inductance DCR max (Ohms)4 at Ipk3 min (µH) pri sec 40.0 40.0 40.0 36.0 36.0 36.0 0.098 0.098 0.098 0.062 0.045 0.156 Leakage inductance max (µH)5 Turns ratio6 pri : sec Ipk3 (A) Output 0.395 0.340 0.370 1 : 0.3 1 : 0.4 1:1 1.3 1.3 1.3 3.3 V, 3.0 A 5.0 V, 2.0 A 12.0 V, 0.83 A 1. When ordering, please specify packaging code: 3 5 6 Pri Sec 2 FA267x-AL CCI xxxx FA2672-ALD D = 13″ machine-ready reel. EIA-481 embossed plastic tape (200 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 400 kHz, 0.4 Vrms, 0 Adc. 3. Ipk is peak primary current drawn at minimum input voltage. 4. DCR for the secondary is per winding. 5. Leakage inductance measured between pins 2 and 3 with all secondary pins shorted. 6. Turns ratio is with the secondary windings connected in parallel. 7. Output is with the secondary windings connected in parallel. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Packaging: 0.433 max 11,00 0.004 /0,10 0.041 1,05 Dot above pin1 0.600 max 15,24 0.413 10,50 8 1 0.024 0,60 0.080 2,03 0.460 11,68 0.050 1,27 0.50 max 12,7 4 Dimensions are in 5 1 0.098 2,50 Recommended 0.098 2,50 Land Pattern inches mm 8 7 Secondary windings to be connected in parallel on PC board Document 560 Revised 06/18/15