Fujitsu MB90573 16-bit proprietary microcontroller Datasheet

FUJITSU SEMICONDUCTOR
DATA SHEET
DS07-13701-8E
16-bit Proprietary Microcontroller
CMOS
F2MC-16LX MB90570 Series
MB90573/574/574C/F574/F574A/V570/V570A
■ DESCRIPTION
The MB90570 series is a general-purpose 16-bit microcontroller developed and designed by Fujitsu for process
control applications in consumer products that require high-speed real time processing. It contains an I2C*2 bus
interface that allows inter-equipment communication to be implemented readily. This product is well adapted to
car audio equipment, VTR systems, and other equipment and systems.
The instruction set of F2MC-16LX CPU core inherits AT architecture of F2MC*1 family with additional instruction
sets for high-level languages, extended addressing mode, enhanced multiplication/division instructions, and enhanced bit manipulation instructions. The microcontroller has a 32-bit accumulator for processing long word data.
The MB90570 series has peripheral resources of an 8/10-bit A/D converter, an 8-bit D/A converter, UART (SCI),
an extended I/O serial interface, an 8/16-bit up/down counter/timer, an 8/16-bit PPG timer, I/O timer (a 16-bit free
run timer, an input capture (ICU), an output compare (OCU)).
*1: F2MC stands for FUJITSU Flexible Microcontroller.
*2: Purchase of Fujitsu I2C components conveys a license under the Philips I2C Patent Rights to use these
components in an I2C system, provided that the system conforms to the I2C Standard Specification as
defined by Philips.
■ PACKAGE
120-pin plastic LQFP
(FPT-120P-M05)
120-pin plastic QFP
120-pin plastic LQFP
(FPT-120P-M13)
(FPT-120P-M21)
MB90570 Series
■ FEATURES
• Clock
Embedded PLL clock multiplication circuit
Operating clock (PLL clock) can be selected from 1/2 to 4× oscillation (at oscillation of 4 MHz, 4 MHz to 16 MHz).
Minimum instruction execution time: 62.5 ns (at oscillation of 4 MHz, 4× PLL clock, operation at VCC of 5.0 V)
• Maximum memory space
16 Mbytes
• Instruction set optimized for controller applications
Rich data types (bit, byte, word, long word)
Rich addressing mode (23 types)
Enhanced signed multiplication/division instruction and RETI instruction functions
Enhanced precision calculation realized by the 32-bit accumulator
• Instruction set designed for high level language (C) and multi-task operations
Adoption of system stack pointer
Enhanced pointer indirect instructions
Barrel shift instructions
• Program patch function (for two address pointers)
• Enhanced execution speed
4-byte instruction queue
• Enhanced interrupt function
8 levels, 34 factors
• Automatic data transmission function independent of CPU operation
Extended intelligent I/O service function (EI2OS): Up to 16 channels
• Embedded ROM size and types
Mask ROM: 128 kbytes/256 kbytes
Flash ROM: 256 kbytes
Embedded RAM size:6 kbytes/10 kbytes (mask ROM)
10 kbytes (flash memory)
10 kbytes (evaluation device)
• Low-power consumption (standby) mode
Sleep mode (mode in which CPU operating clock is stopped)
Stop mode (mode in which oscillation is stopped)
CPU intermittent operation mode
Hardware standby mode
• Process
CMOS technology
• I/O port
General-purpose I/O ports (CMOS): 63 ports
General-purpose I/O ports (with pull-up resistors): 24 ports
General-purpose I/O ports (open-drain): 10 ports
Total: 97 ports
• Timer
Timebase timer/watchdog timer: 1 channel
8/16-bit PPG timer: 8-bit × 2 channels or 16-bit × 1 channel
• 8/16-bit up/down counter/timer: 1 channel (8-bit × 2 channels)
(Continued)
2
MB90570 Series
(Continued)
• 16-bit I/O timer
16-bit free run timer:
Input capture (ICU):
•
•
•
•
•
•
•
•
•
•
1 channel
Generates an interrupt request by latching a 16-bit free run timer counter value upon
detection of an edge input to the pin.
Output compare (OCU): Generates an interrupt request and reverse the output level upon detection of a match
between the 16-bit free run timer counter value and the compare setting value.
Extended I/O serial interface: 3 channels
I2C interface (1 channel)
Serial I/O port for supporting Inter IC BUS
UART0 (SCI), UART1 (SCI)
With full-duplex double buffer
Clock asynchronized or clock synchronized transmission can be selectively used.
DTP/external interrupt circuit (8 channels)
A module for starting extended intelligent I/O service (EI2OS) and generating an external interrupt triggered
by an external input.
Delayed interrupt generation module
Generates an interrupt request for switching tasks.
8/10-bit A/D converter (8 channels)
8/10-bit resolution
Starting by an external trigger input.
Conversion time: 26.3 µs
8-bit D/A converter (based on the R-2R system)
8-bit resolution: 2 channels (independent)
Setup time: 12.5 µs
Clock timer: 1 channel
Chip select output (8 channels)
An active level can be set.
Clock output function
3
MB90570 Series
■ PRODUCT LINEUP
Part number
Item
Classification
MB90573
MB90574/C
Mask ROM products
ROM size
128 kbytes
RAM size
6 kbytes
MB90F574/A
MB90V570/A
Flash ROM products Evaluation product
256 kbytes
None
10 kbytes
The number of instructions: 340
Instruction bit length: 8 bits, 16 bits
Instruction length: 1 byte to 7 bytes
Data bit length: 1 bit, 8 bits, 16 bits
Minimum execution time: 62.5 ns (at machine clock of 16 MHz)
Interrupt processing time: 1.5 µs (at machine clock of 16 MHz, minimum value)
CPU functions
General-purpose I/O ports (CMOS output): 63
General-purpose I/O ports (with pull-up resistor): 24
General-purpose I/O ports (N-ch open-drain output): 10
Total: 97
Ports
UART0 (SCI), UART1 (SCI)
Clock synchronized transmission (62.5 kbps to 1 Mbps)
Clock asynchronized transmission (1202 bps to 9615 bps)
Transmission can be performed by bi-directional serial transmission or by
master/slave connection.
8/10-bit A/D converter
Resolution: 8/10-bit
Number of inputs: 8
One-shot conversion mode (converts selected channel only once)
Scan conversion mode (converts two or more successive channels and can
program up to 8 channels.)
Continuous conversion mode (converts selected channel continuously)
Stop conversion mode (converts selected channel and stop operation repeatedly)
8/16-bit PPG timer
Number of channels: 1 (or 8-bit × 2 channels)
PPG operation of 8-bit or 16-bit
A pulse wave of given intervals and given duty ratios can be output.
Pulse interval: 62.5 ns to 1 µs (at oscillation of 4 MHz, machine clock of 16 MHz)
8/16-bit up/down counter/
timer
16-bit
free run timer
16-bit
I/O timer
Number of channels: 1 (or 8-bit × 2 channels)
Event input: 6 channels
8-bit up/down counter/timer used: 2 channels
8-bit re-load/compare function supported: 1 channel
Number of channel: 1
Overflow interrupts
Output
compare
(OCU)
Number of channels: 4
Pin input factor: A match signal of compare register
Input
capture
(ICU)
Number of channels: 2
Rewriting a register value upon a pin input (rising, falling, or both edges)
(Continued)
4
MB90570 Series
(Continued)
Part number
MB90573
Item
DTP/external interrupt
circuit
Delayed interrupt
generation module
MB90574/C
MB90F574/A
MB90V570/A
Number of inputs: 8
Started by a rising edge, a falling edge, an “H” level input, or an “L” level input.
External interrupt circuit or extended intelligent I/O service (EI2OS) can be used.
An interrupt generation module for switching tasks used in real time operating
systems.
Clock synchronized transmission (3125 bps to 1 Mbps)
LSB first/MSB first
Extended I/O serial interface
I2C interface
Timebase timer
Serial I/O port for supporting Inter IC BUS
18-bit counter
Interrupt interval: 1.024 ms, 4.096 ms, 16.384 ms, 131.072 ms
(at oscillation of 4 MHz)
8-bit resolution
Number of channels: 2 channels
Based on the R-2R system
8-bit D/A converter
Watchdog timer
Reset generation interval: 3.58 ms, 14.33 ms, 57.23 ms, 458.75 ms
(at oscillation of 4 MHz, minimum value)
Low-power consumption
(standby) mode
Sleep/stop/CPU intermittent operation/clock timer/hardware standby
Process
CMOS
Power supply voltage for
operation*
4.5 V to 5.5 V
* : Varies with conditions such as the operating frequency. (See section “■ ELECTRICAL CHARACTERISTICS.”)
Assurance for the MB90V570/A is given only for operation with a tool at a power voltage of 4.5 V to 5.5 V, an
operating temperature of 0 °C to +25 °C, and an operating frequency of 1 MHz to 16 MHz.
■ PACKAGE AND CORRESPONDING PRODUCTS
Package
MB90573
MB90574
MB90F574/A
MB90574C
×
FPT-120P-M05
FPT-120P-M13
FPT-120P-M21
×
×
: Available ×: Not available
Note : For more information about each package, see section “■ PACKAGE DIMENSIONS.”
5
MB90570 Series
■ DIFFERENCES AMONG PRODUCTS
Memory Size
In evaluation with an evaluation product, note the difference between the evaluation product and the product
actually used. The following items must be taken into consideration.
• The MB90V570/A does not have an internal ROM, however, operations equivalent to chips with an internal
ROM can be evaluated by using a dedicated development tool, enabling selection of ROM size by settings of
the development tool.
• In the MB90V570/A, images from FF4000H to FFFFFFH are mapped to bank 00, and FE0000H to FF3FFFH to
mapped to bank FE and FF only. (This setting can be changed by configuring the development tool.)
• In the MB90F574/574/573/F574A/574C, images from FF4000H to FFFFFFH are mapped to bank 00, and
FF0000H to FF3FFFH to bank FF only.
• The products designated with /A or /C are different from those without /A or /C in that they are DTP/externallyinterrupted types which return from standby mode at the ch.0 to ch.1 edge request.
6
MB90570 Series
■ PIN ASSIGNMENT
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
P30/ALE
VSS
P27/A23
P26/A22
P25/A21
P24/A20
P23/A19
P22/A18
P21/A17
P20/A16
P17/AD15
P16/AD14
P15/AD13
P14/AD12
P13/AD11
P12/AD10
P11/AD09
P10/AD08
P07/AD07
P06/AD06
P05/AD05
P04/AD04
P03/AD03
P02/AD02
P01/AD01
P00/AD00
VCC
X1
X0
VSS
(Top view)
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
RST
MD0
MD1
MD2
HST
PC3
PC2
PC1
PC0
PB7
PB6/ADTG
PB5/IRQ5
PB4/IRQ4
PB3/IRQ3
PB2/IRQ2
PB1/IRQ1
X0A
X1A
PB0/IRQ0
PA7/SCL
PA6/SDA
PA5/ZIN1
PA4/BIN1
PA3/AIN1/IRQ7
PA2/ZIN0
PA1/BIN0
PA0/AIN0/IRQ6
VSS
P97/CS7
P96/CS6
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P66/OUT2
P67/OUT3
VSS
C
P70
P71
P72
DVCC
DVSS
P73/DA0
P74/DA1
AVCC
AVRH
AVRL
AVSS
P80/AN0
P81/AN1
P82/AN2
P83/AN3
P84/AN4
P85/AN5
P86/AN6
P87/AN7
VCC
P90/CS0
P91/CS1
P92/CS2
P93/CS3
P94/CS4
P95/CS5
P31/RD
P32/WRL
P33/WRH
P34/HRQ
P35/HAK
P36/RDY
P37/CLK
VCC
P40/SIN0
P41/SOT0
P42/SCK0
P43/SIN1
P44/SOT1
P45/SCK1
P46/PPG0
P47/PPG1
P50/SIN2
P51/SOT2
P52/SCK2
P53/SIN3
P54/SOT3
P55/SCK3
P56/IN0
P57/IN1
P60/SIN4
P61/SOT4
P62/SCK4
P63/CKOT
P64/OUT0
P65/OUT1
(FPT-120P-M05)
(FPT-120P-M13)
(FPT-120P-M21)
7
MB90570 Series
■ PIN DESCRIPTION
Pin no.
LQFP-120 *1
QFP-120 *2
Pin name
Circuit
type
Function
92,93
X0,X1
A
High speed oscillator pins
74,73
X0A,X1A
B
Low speed oscillator pins
MD0 to MD2
C
These are input pins used to designate the operating mode. They
should be connected directly to Vcc or Vss.
90
RST
C
Reset input pin
86
HST
C
Hardware standby input pin
D
In single chip mode, these are general purpose I/O pins. When set for
input, they can be set by the pull-up resistance setting register
(RDR0). When set for output, this setting will be invalid.
89 to 87
P00 to P07
95 to 102
AD00 toAD07
In external bus mode, these pins function as address low output/data
low I/O pins.
P10 to P17
In single chip mode, these are general purpose I/O pins. When set for
input, they can be set by the pull-up resistance setting register
(RDR1). When set for output, the setting will be invalid.
103 to 110
D
In external bus mode, these pins function as address middle output/
data high I/O pins.
AD08 toAD15
P20 to P27
111 to 118
A16 to A23
In single chip mode this is a general-purpose I/O port.
E
P30
120
ALE
In single chip mode this is a general-purpose I/O port.
E
P31
1
RD
WRL
WRH
HRQ
6
HAK
P36
RDY
In external bus mode, this pin functions as the data bus upper 8-bit
write strobe signal output pin.
In single chip mode this is a general-purpose I/O port.
E
P35
5
In external bus mode, this pin functions as the data bus lower 8-bit
write strobe signal output pin.
In single chip mode this is a general-purpose I/O port.
E
P34
4
In external bus mode, this pin functions as the read strobe signal output pin.
In single chip mode this is a general-purpose I/O port.
E
P33
3
In external bus mode, this pin functions as the address latch enable
signal output pin.
In single chip mode this is a general-purpose I/O port.
E
P32
2
In external bus mode, these pins function as address high output
pins.
In external bus mode, this pin functions as the hold request signal input pin.
In single chip mode this is a general-purpose I/O port.
E
E
In external bus mode, this pin functions as the hold acknowledge signal output pin.
In single chip mode this is a general-purpose I/O port.
In external bus mode, this pin functions as the ready signal input pin.
(Continued)
*1 : FPT-120P-M05
*2 : FPT-120P-M13, FPT-120P-M21
8
MB90570 Series
Pin no.
LQFP-120 *1
QFP-120 *2
Pin name
Circuit
type
P37
7
CLK
In single chip mode this is a general-purpose I/O port.
E
In external bus mode, this pin functions as the clock (CLK) signal output pin.
In single chip mode this is a general-purpose I/O port. It can be set to
open drain by the ODR4 register.
P40
SIN0
This is also the UART ch.0 serial data input pin. While UART ch.0 is
in input operation, this input signal is in continuous use, and therefore
the output function should only be used when needed. If shared by
output from other functions, this pin should be output disabled during
SIN operation.
P41
In single chip mode this is a general-purpose I/O port. It can be set to
open drain by the ODR4 register.
9
F
10
F
SOT0
This is also the UART ch.0 serial data output pin. This function is valid
when UART ch.0 is enabled for data output.
P42
In single chip mode this is a general-purpose I/O port. It can be set to
open drain by the ODR4 register.
11
F
SCK0
This is also the UART ch.0 serial clock I/O pin. This function is valid
when UART ch.0 is enabled for clock output.
P43
In single chip mode this is a general-purpose I/O port. It can be set to
open-drain by the ODR4 register.
SIN1
This is also the UART ch.1 serial data input pin. While UART ch.1 is
in input operation, this input signal is in continuous use, and therefore
the output function should only be used when needed. If shared by
output from other functions, this pin should be output disabled during
SIN operation.
P44
In single chip mode this is a general-purpose I/O port. It can be set to
opendrain by the ODR4 register.
12
F
13
F
SOT1
This is also the UART ch.1 serial data output pin. This function is valid
when UART ch.1 is enabled for data output.
P45
In single chip mode this is a general-purpose I/O port. It can be set to
open drain by the ODR4 register.
14
F
SCK1
This is also the UART ch.1 serial clock I/O pin. This function is valid
when UART ch.1 is enabled for clock output.
P46,P47
In single chip mode this is a general-purpose I/O port. It can be set to
open drain by the ODR4 register.
15,16
17
Function
F
PPG0,PPG1
These are also the PPG0, 1 output pins. This function is valid when
PPG0, 1 output is enabled.
P50
In single chip mode this is a general-purpose I/O port.
SIN2
E
This is also the I/O serial ch.0 data input pin. During serial data input,
this input signal is in continuous use, and therefore the output function
should only be used when needed.
(Continued)
*1 : FPT-120P-M05
*2 : FPT-120P-M13, FPT-120P-M21
9
MB90570 Series
Pin no.
LQFP-120 *1
QFP-120 *2
Pin name
Circuit
type
P51
18
SOT2
In single chip mode this is a general-purpose I/O port.
E
P52
19
SCK2
SIN3
SOT3
E
SCK3
IN0,IN1
E
E
F
These are also the input capture ch.0/1 trigger input pins. During input
capture signal input on ch.0/1 this function is in continuous use, and
therefore the output function should only be used when needed.
In single chip mode this is a general-purpose I/O port. When set for
input it can be set by the pull-up resistance register (RDR6). When set
for output this setting will be invalid.
SIN4
This is also the I/O serial ch.2 data input pin. During serial data input
this function is in continuous use, and therefore the output function
should only be used when needed.
P61
In single chip mode this is a general-purpose I/O port. When set for
input it can be set by the pull-up resistance register (RDR6). When set
for output this setting will be invalid.
26
F
SOT4
This is also the I/O serial ch.2 data output pin. This function is valid
when serial ch.2 is enabled for serial data output.
P62
In single chip mode this is a general-purpose I/O port. When set for
input it can be set by the pull-up resistance register (RDR6). When set
for output this setting will be invalid.
27
F
SCK4
This is also the I/O serial ch.2 serial clock I/O pin. This function is valid
when serial ch.2 is enabled for serial data output.
P63
In single chip mode this is a general-purpose I/O port. When set for
input it can be set by the pull-up resistance register (RDR6). When set
for output this setting will be invalid.
28
F
CKOT
*1 : FPT-120P-M05
*2 : FPT-120P-M13, FPT-120P-M21
10
This is also the I/O serial ch.1 clock I/O pin. This function is valid when
serial ch.1 is enabled for serial data output.
In single chip mode this is a general-purpose I/O port.
P60
25
This is also the I/O serial ch.1 data output pin. This function is valid
when serial ch.1 is enabled for serial data output.
In single chip mode this is a general-purpose I/O port.
P56,P57
23,24
This is also the I/O serial ch.1 data input pin. During serial data input,
this input signal is in continuous use, and therefore the output function
should only be used when needed.
In single chip mode this is a general-purpose I/O port.
E
P55
22
This is also the I/O serial ch.0 clock I/O pin. This function is valid when
serial ch.0 is enabled for serial data output.
In single chip mode this is a general-purpose I/O port.
P54
21
This is also the I/O serial ch.0 data output pin. This function is valid
when serial ch.0 is enabled for serial data output.
In single chip mode this is a general-purpose I/O port.
E
P53
20
Function
This is also the clock monitor output pin. This function is valid when
clock monitor output is enabled.
(Continued)
MB90570 Series
Pin no.
Pin name
LQFP-120 *1
QFP-120 *2
Circuit
type
P64 to P67
29 to 32
F
OUT0 to
OUT3
35 to 37
40,41
P70 to P72
P73,P74
DA0,DA1
E
I
P80 to P87
46 to 53
AN0 to AN7
34
CS0 to CS7
C
AIN0
G
E
ZIN0
AIN1
E
ZIN1
This pin is also used as count clock A input for 8/16-bit up-down
counter ch.0.
This pin is also used as count clock B input for 8/16-bit up-down
counter ch.0.
This pin is also used as count clock Z input for 8/16-bit up-down
counter ch.0.
This pin is also used as count clock A input for 8/16-bit up-down
counter ch.1.
This is a general purpose I/O port.
E
PA5
69
This is the power supply stabilization capacitor pin. It should be
connected externally to an 0.1 µF ceramic capacitor. Note that this is
not required on the FLASH model (MB90F574/A) and MB90574C.
This pin can also be used as interrupt request input ch.7.
PA4
BIN1
These are also chip select signal output pins. This function is valid
when chip select signal output is enabled.
This is a general purpose I/O port.
IRQ7
68
These are also A/D converter analog input pins. This function is valid
when analog input is enabled.
This is a general purpose I/O port.
E
PA3
67
These are also the D/A converter ch.0,1 analog signal output pins.
This is a general purpose I/O port.
E
PA2
66
These are general purpose I/O ports.
This pin can also be used as interrupt request input ch. 6.
PA1
BIN0
These are general purpose I/O ports.
This is a general purpose I/O port.
IRQ6
65
These are also the output compare ch.0 to ch.3 event output pins.
This function is valid when the respective channel(s) are enabled for
output.
These are general purpose I/O ports.
E
PA0
64
In single chip mode these are general-purpose I/O ports. When set for
input they can be set by the pull-up resistance register (RDR6). When
set for output this setting will be invalid.
These are general purpose I/O ports.
K
P90 to P97
55 to 62
Function
This pin is also used as count clock B input for 8/16-bit up-down
counter ch.1.
This is a general purpose I/O port.
E
This pin is also used as count clock Z input for 8/16-bit up-down
counter ch.1.
(Continued)
*1 : FPT-120P-M05
*2 : FPT-120P-M13, FPT-120P-M21
11
MB90570 Series
(Continued)
Pin no.
LQFP-120 *1
QFP-120 *2
Pin name
Circuit
type
PA6
70
This is a general purpose I/O port.
L
SDA
PA7
71
L
SCL
This pin is also used as the clock I/O pin for the I2C interface. This
function is valid when the I2C interface is enabled for operation. While
the I2C interface is operating, this port should be set to the input level
(DDRA: bit7 = 0).
These are general-purpose I/O ports.
E
IRQ0,
IRQ1 to IRQ5
PB6
These pins are also the external interrupt input pins. IRQ0, 1 are enabled for both rising and falling edge detection, and therefore cannot
be used for recovery from STOP status for MB90V570, MB90F574,
MB90573 and MB90574. However, IRQ0, 1 can be used for recovery
from STOP status for MB90V570A, MB90F574A and MB90574C.
This is a general purpose I/O port.
E
This is also the A/D converter external trigger input pin. While the A/D
converter is in input operation, this input signal is in continuous use,
and therefore the output function should only be used when needed.
PB7
E
This is a general purpose I/O port.
82 to 85
PC0 to PC3
E
These are general purpose I/O ports.
8,54,94
VCC
Power
supply
These are power supply (5V) input pins.
33,63,
91,119
VSS
Power
supply
These are power supply (0V) input pins.
80
81
ADTG
42
AVCC
H
This is the analog macro (D/A, A/D etc.) Vcc power supply input pin.
43
AVRH
J
This is the A/D converter Vref+ input pin. The input voltage should not
exceed Vcc.
44
AVRL
H
This is the A/D converter Vref- input pin. The input voltage should not
less than Vss.
45
AVSS
H
This is the analog macro (D/A, A/D etc.) Vss power supply input pin.
38
DVCC
H
This is the D/A converter Vref input pin. The input voltage should not
exceed Vcc.
39
DVSS
H
This is the D/A converter GND power supply pin. It should be set to
Vss equivalent potential.
*1 : FPT-120P-M05
*2 : FPT-120P-M13, FPT-120P-M21
12
This pin is also used as the data I/O pin for the I2C interface. This
function is valid when the I2C interface is enabled for operation. While
the I2C interface is operating, this port should be set to the input level
(DDRA: bit6 = 0).
This is a general purpose I/O port.
PB0,
PB1 to PB5
72,
75 to 79
Function
MB90570 Series
■ I/O CIRCUIT TYPE
Type
Circuit
Remarks
• Oscillator circuit
Oscillator recovery resistance for high
speed = approx. 1 MΩ
X1
X0
A
Standby control signal
• Oscillator circuit
Oscillator recovery resistance for low
speed = approx. 10 MΩ
X1A
X0A
B
Standby control signal
• Hysteresis input pin
Resistance value = approx. 50 kΩ (typ.)
R
Hysteresis input
C
VCC
VCC
P-ch
D
Selective signal either
with a pull-up resistor or
without it.
P-ch
N-ch
R
Hysteresis input
• CMOS hysteresis input pin with input
pull-up control
• CMOS level output.
• CMOS hysteresis input
(Includes input shut down standby
control function)
• Pull-up resistance value =
approx. 50 kΩ(typ.)
IOL = 4mA
Standby control for input interruption
IOL = 4 mA
(Continued)
13
MB90570 Series
Type
Circuit
Remarks
• CMOS hysteresis input/output pin.
• CMOS level output
• CMOS hysteresis input
(Includes input shut down standby
control function)
IOL = 4 mA
VCC
P-ch
E
N-ch
R
Hysteresis input
Standby control for input interruption
IOL = 4 mA
• CMOS hysteresis input/output pin.
• CMOS level output
• CMOS hysteresis input
(Includes input shut down standby
control function)
IOL = 10 mA (Large current port)
VCC
P-ch
F
N-ch
R
IOL = 10 mA
Hysteresis input
Standby control for input interruption
• C pin output
(capacitance connector pin).
VCC
P-ch
G
On the MB90F574 this pin is not
connected (NC).
N-ch
• Analog power supply protector
circuit.
VCC
P-ch
H
AVP
N-ch
VCC
P-ch
N-ch
I
R
Hysteresis input
• CMOS hysteresis input/output
• Analog output/CMOS output
dual-function pin (CMOS output is not
available during analog output.)
(Analog output priority: DAE = 1)
• Includes input shut down standby
control function.
IOL = 4mA
Standby control for input interruption
DAO
IOL = 4 mA
(Continued)
14
MB90570 Series
(Continued)
Type
Circuit
Remarks
• A/D converter ref+ power supply input
pin(AVRH), with power supply
protector circuit.
VCC
P-ch
J
P-ch
N-ch
ANE
AVR
N-ch
ANE
• CMOS hysteresis input /analog input
dual-function pin.
• CMOS output
• Includes input shut down function at
input shut down standby.
VCC
P-ch
N-ch
K
R
Hysteresis input
Standby control for input interruption
Analog input
IOL = 4 mA
• Hysteresis input
• N-ch open-drain output
• Includes input shut down standby
control function.
IOL= 4mA
VCC
N-ch
N-ch
L
R
Hysteresis input
IOL = 4 mA
Standby control for input interruption
15
MB90570 Series
■ HANDLING DEVICES
1. Preventing Latchup
CMOS ICs may cause latchup in the following situations:
• When a voltage higher than Vcc or lower than Vss is applied to input or output pins.
• When a voltage exceeding the rating is applied between Vcc and Vss.
• When AVcc power is supplied prior to the Vcc voltage.
In turning on/turning off the analog power supply, make sure the analog power voltage (AVCC, AVRH, DVCC)and
analog input voltages not exceed the digital voltage (VCC).
2. Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefor they must be tied to VCC or Ground through resistors. In this case those resistors should be
more than 2 kΩ.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
3. Notes on Using External Clock
In using the external clock, drive X0 pin only and leave X1 pin unconnected.
• Using external clock
MB90570 series
X0
Open
X1
4. Unused Sub Clock Mode
If sub clock modes are not used, the oscillator should be connected to the X01A pin and X1A pin
5. Power Supply Pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, connect the pins external power and ground lines to
lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals caused by the rise
in the ground level, and to conform to the total current rating.
Make sure to connect VCC and VSS pins via lowest impedance to power lines.
16
MB90570 Series
It is recommended to provide a bypass capacitor of around 0.1 µF between VCC and VSS pin near the device.
• Using power supply pins
VCC
VSS
VCC
VSS
VSS
MB90570 series
VCC
VCC
VSS
VSS
VCC
6. Crystal Oscillator Circuit
Noises around X0 or X1 pins may be possible causes of abnormal operations. Make sure to provide bypass
capacitors via shortest distance from X0, X1 pins, crystal oscillator (or ceramic resonator) and ground lines, and
make sure, to the utmost effort, that lines of oscillation circuit do not cross the lines of other circuits.
It is highly recommended to provide a printed circuit board art work surrounding X0 and X1 pins with an grand
area for stabilizing the operation.
7. Turning-on Sequence of Power Supply to A/D Converter and Analog Inputs
Make sure to turn on the A/D converter power supply, D/A converter power supply (AVCC, AVRH, AVRL, DVCC,DVSS)
and analog inputs (AN0 to AN7) after turning-on the digital power supply (VCC).
Turn-off the digital power after turning off the A/D converter supply and analog inputs. In this case, make sure
that the voltage does not exceed AVRH or AVCC (turning on/off the analog and digital power supplies simultaneously is acceptable).
8. Connection of Unused Pins of A/D Converter
Connect unused pins of A/D converter to AVCC = VCC, AVSS = AVRH = DVCC = VSS.
9. N.C. Pins
The N.C. (internally connected) pins must be opened for use.
10. Notes on Energization
To prevent the internal regulator circuit from malfunctioning, set the voltage rise time during energization at 50
or more µs (0.2 V to 2.7 V).
11. Indeterminate outputs from ports 0 and 1
The outputs from ports 0 and 1 become indeterminate during oscillation setting time of step-down circuit (during
a power-on reset) after the power is turned on. (MB90573, MB90574, MB90V570, MB90V570A)
17
MB90570 Series
The series without built-in step-down circuit have no oscillation setting time of step-down circuit, so outputs
should not become indeterminate. (MB90F574,MB90F574A,MB90574C)
Timing chart of indeterminate outputs from ports 0 and 1
Oscillation setting time *2
Step-down circuit setting time *1
VCC (power-supply pin)
PONR (power-on reset) signal
RST (external asynchronous reset) signal
RST (internal reset) signal
Oscillation clock signal
KA (internal operating clock A) signal
KB (internal operating clock B) signal
PORT (port output) signal
Period of indeterminate
*1: Step-down circuit setting time 217/oscillation clock frequency (oscillation clock frequency of 16 MHz: 8.19 ms)
*2: Oscillation setting time
218/oscillation clock frequency (oscillation clock frequency of 16 MHz: 16.38 ms)
12. Initialization
In the device, there are internal registers which are initialized only by a power-on reset. Turn on the power again
to initialize these registers.
13. Return from standby state
If the power-supply voltage goes below the standby RAM holding voltage in the standby state, the device may
fail to return from the standby state. In this case, reset the device via the external reset pin to return to the normal
state.
14. Precautions for Use of ’DIV A, Ri,’ and ’DIVW A, Ri’ Instructions
The signed multiplication-division instructions ’DIV A, Ri,’ and ’DIVW A, RWi’ should be used when the corresponding bank registers (DTB, ADB, USB, SSB) are set to value ’00h.’ If the corresponding bank registers (DTB,
ADB, USB, SSB) are set to a value other than ’00h,’ then the remainder obtained after the execution of the
instruction will not be placed in the instruction operand register.
15. Precautions for Use of REALOS
Extended intelligent I/O service (EI2OS) cannot be used, when REALOS is used.
16. Caution on PLL Clock Mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
18
MB90570 Series
■ BLOCK DIAGRAM
Interrupt controller
F2MC–16LX
CPU
X0, X1
X0A, X1A
Main clock
HST
P10/AD08 to P17/AD15
P20/A16 to P27/A23
2
8
8
Port 0, 1, 2
P70 to P72
P73/DA0
P74/DA1
8-bit
D/A
converter
× 2 ch.
Clock control
block
(including timebase
timer)
Sub clock
RST
P00/AD00 to P07/AD07
3
Port 7
DVCC
DVSS
Port 9
16
8
Chip select
output
8
P30/ALE
8
8
P90/CS0 to P97/CS7
Port A
2 External bus
interface
6
P31/RD
P32/WRL
P33/WRH
P34/HRQ
PA1/BIN0
PA2/ZIN0
P35/HAK
P36/RDY
P37/CLK
Port 3
P40/SIN0
Port 4
P41/SOT0
2
P42/SCK0
P43/SIN1
2
P44/SOT1
2
UART0
(SCI),
UART1
(SCI)
P45/SCK1
P46/PPG0
8/16-bit
PPG timer
ch.0
P47/PPG1
P50/SIN2
Port 5
P51/SOT2
P52/SCK2
2
P53/SIN3
2
P54/SOT3
2
PA4/BIN1
PA5/ZIN1
I2C bus
2
PA6/SDA
PA7/SCL
DTP/
external
interrupt
circuit
× 8 ch.
PA0/AIN0/IRQ6
6
6
PB0/IRQ0 to
PB5/IRQ5
PB7
Port B
PB6/ADTG
8/10-bit
A/D converter
× 8 ch.
8
8
AVRL
AVRH
AVCC
AVSS
P80/AN0 to
P87/AN7
Port 8
2
P57/IN1
PA3/AIN1/IRQ7
6
SIO × 2 ch
P55/SCK3
P56/IN0
Internal data bus
8/16-bit up/down
counter/timer
Input capture
(ICU)
Port C
4
PC0 to PC3
16-bit free run timer
P64/OUT0 to P67/OUT3
4
4
Output
compare
(OCU)
P60/SIN4
P61/SOT4
SIO × 1 ch.
RAM
ROM
P62/SCK4
Port 6
P63/CKOT
Other pins
MD0 to MD2,
C, VCC, VSS
Clock output
P00 to P07 (8 ports): Provided with a register optional input pull-up resistor
P10 to P17 (8 ports): Provided with a register optional input pull-up resistor
P40 to P47 (8 ports): Heavy-current (IOL = 10 mA) port
P60 to P67 (8 ports): Provided with a register optional input pull-up resistor
19
MB90570 Series
■ MEMORY MAP
Single chip mode
A mirror function is
supported.
Internal ROM
external bus mode
A mirror function
is supported.
External ROM
external bus mode
FFFFFFH
ROM area
ROM area
ROM area
(image of
Address #2 bank FF)
ROM area
(image of
bank FF)
Address #1
FC0000H
010000H
004000H
Address #3
RAM Register
RAM Register
Peripheral
Peripheral
000100H
0000C0H
000000H
Part number
RAM Register
Peripheral
Address #1*
Address #2 *
Address #3 *
MB90573
FE0000H
004000H
001800H
MB90574/C
FC0000H
004000H
002900H
MB90F574/A
FC0000H
004000H
002900H
: Internal access memory
: External access memory
: Inhibited area
*: Addresses #1, #2 and #3 are unique to the product type.
Note : The ROM data of bank FF is reflected in the upper address of bank 00, realizing effective use of the C
compiler small model. The lower 16-bit of bank FF and the lower 16-bit of bank 00 is assigned to the same
address, enabling reference of the table on the ROM without stating “far”.
For example, if an attempt has been made to access 00C000H, the contents of the ROM at FFC000H are
accessed actually. Since the ROM area of the FF bank exceeds 48 kbytes, the whole area cannot be reflected
in the image for the 00 bank. The ROM data at FF4000H to FFFFFFH looks, therefore, as if it were the image
for 00400H to 00FFFFH. Thus, it is recommended that the ROM data table be stored in the area of FF4000H
to FFFFFFH.
20
MB90570 Series
■ F2MC-16LX CPU PROGRAMMING MODEL
• Dedicated registers
AH
:Accumulator (A)
Dual 16-bit register used for storing results of calculation etc. The two
16-bit registers can be combined to be used as a 32-bit register.
AL
USP
:User stack pointer (USP)
The 16-bit pointer indicating a user stack address.
SSP
:System stack pointer (SSP)
The 16-bit pointer indicating the status of the system stack address.
PS
:Processor status (PS)
The 16-bit register indicating the system status.
PC
:Program counter (PC)
The 16-bit register indicating storing location of the current instruction
code.
DPR
:Direct page register (DPR)
The 8-bit register indicating bit 8 through 15 of the operand address
in the short direct addressing mode.
PCB
:Program bank register (PCB)
The 8-bit register indicating the program space.
DTB
:Data bank register (DTB)
The 8-bit register indicating the data space.
USB
:User stack bank register (USB)
The 8-bit register indicating the user stack space.
SSB
:System stack bank register (SSB)
The 8-bit register indicating the system stack space.
ADB
:Additional data bank register (ADB)
The 8-bit register indicating the additional data space.
8-bit
16-bit
32-bit
21
MB90570 Series
• General-purpose registers
Maximum of 32 banks
R7
R6
RW7
R5
R4
RW6
R3
R2
RW5
R1
R0
RW4
RL3
RL2
RW3
RL1
RW2
RW1
RL0
RW0
000180H + (RP × 10H)
16-bit
• Processor status (PS)
ILM
RP
CCR
bit 15 bit 14 bit 13 bit 12 bit 11 bit 10 bit 9 bit 8 bit 7 bit 6
PS
Initial value
—: Reserved
X: Undefined
22
ILM2 ILM1 ILM0
0
0
0
bit 5 bit 4
bit 3 bit 2
bit 1
bit 0
B4
B3
B2
B1
B0
—
I
S
T
N
Z
V
C
0
0
0
0
0
—
0
1
X
X
X
X
X
MB90570 Series
■ I/O MAP
Address
Abbreviated
register
name
000000H
PDR0
000001H
Read/
write
Resource name
Initial value
Port 0 data register
R/W
Port 0
X X X X X X X XB
PDR1
Port 1 data register
R/W
Port 1
X X X X X X X XB
000002H
PDR2
Port 2 data register
R/W
Port 2
X X X X X X X XB
000003H
PDR3
Port 3 data register
R/W
Port 3
X X X X X X X XB
000004H
PDR4
Port 4 data register
R/W
Port 4
X X X X X X X XB
000005H
PDR5
Port 5 data register
R/W
Port 5
X X X X X X X XB
000006H
PDR6
Port 6 data register
R/W
Port 6
X X X X X X X XB
000007H
PDR7
Port 7 data register
R/W
Port 7
X X X X X X X XB
000008H
PDR8
Port 8 data register
R/W
Port 8
X X X X X X X XB
000009H
PDR9
Port 9 data register
R/W
Port 9
X X X X X X X XB
00000AH
PDRA
Port A data register
R/W
Port A
X X X X X X X XB
00000BH
PDRB
Port B data register
R/W
Port B
X X X X X X X XB
00000CH
PDRC
Port C data register
R/W
Port C
X X X X X X X XB
Register name
00000DH
to
00000FH
(Disabled)
000010H
DDR0
Port 0 direction register
R/W
Port 0
0 0 0 0 0 0 0 0B
000011H
DDR1
Port 1 direction register
R/W
Port 1
0 0 0 0 0 0 0 0B
000012H
DDR2
Port 2 direction register
R/W
Port 2
0 0 0 0 0 0 0 0B
000013H
DDR3
Port 3 direction register
R/W
Port 3
0 0 0 0 0 0 0 0B
000014H
DDR4
Port 4 direction register
R/W
Port 4
0 0 0 0 0 0 0 0B
000015H
DDR5
Port 5 direction register
R/W
Port 5
0 0 0 0 0 0 0 0B
000016H
DDR6
Port 6 direction register
R/W
Port 6
0 0 0 0 0 0 0 0B
000017H
DDR7
Port 7 direction register
R/W
Port 7
– – – 0 0 0 0 0B
000018H
DDR8
Port 8 direction register
R/W
Port 8
0 0 0 0 0 0 0 0B
000019H
DDR9
Port 9 direction register
R/W
Port 9
0 0 0 0 0 0 0 0B
00001AH
DDRA
Port A direction register
R/W
Port A
0 0 0 0 0 0 0 0B
00001BH
DDRB
Port B direction register
R/W
Port B
0 0 0 0 0 0 0 0B
00001CH
DDRC
Port C direction register
R/W
Port C
0 0 0 0 0 0 0 0B
00001DH
ODR4
Port 4 output pin register
R/W
Port 4
0 0 0 0 0 0 0 0B
00001EH
ADER
Analog input enable register
R/W
Port 8,
8/10-bit
A/D converter
1 1 1 1 1 1 1 1B
00001FH
(Disabled)
000020H
SMR0
Serial mode register 0
R/W
000021H
SCR0
Serial control register 0
R/W
UART0
(SCI)
0 0 0 0 0 0 0 0B
0 0 0 0 0 1 0 0B
(Continued)
23
MB90570 Series
Address
Abbreviated
register
name
000022H
SIDR0/
SODR0
000023H
Read/
write
Resource
name
Serial input data register 0/
serial output data register 0
R/W
SSR0
Serial status register 0
R/W
UART0
(SCI)
000024H
SMR1
Serial mode register 1
R/W
0 0 0 0 0 0 0 0B
000025H
SCR1
Serial control register 1
R/W
0 0 0 0 0 1 0 0B
000026H
SIDR1/
SODR1
Serial input data register 1/
serial output data register 1
R/W
000027H
SSR1
Serial status register 1
R/W
000028H
CDCR0
Register name
Communications prescaler control
register 0
000029H
00002AH
CDCR1
Communications prescaler control
register 1
X X X X X X X XB
0 0 0 0 1 – 0 0B
R/W
0 – – – 1 1 1 1B
R/W
Communications
prescaler
register 0
0 – – – 1 1 1 1B
(Disabled)
000030H
ENIR
DTP/interrupt enable register
R/W
EIRR
DTP/interrupt factor register
R/W
ELVR
Request level setting register
R/W
000034H
0 0 0 0 0 0 0 0B
DTP/external
interrupt circuit
X X X X X X X XB
0 0 0 0 0 0 0 0B
0 0 0 0 0 0 0 0B
(Disabled)
000035H
000036H
ADCS1
A/D control status register lower
digits
R/W
000037H
ADCS2
A/D control status register upper
digits
R/W or W
000038H
ADCR1
A/D data register lower digits
R
X X X X X X X XB
000039H
ADCR2
A/D data register upper digits
W
0 0 0 0 1 – X XB
00003AH
DADR0
D/A converter data register ch.0
R/W
X X X X X X X XB
00003BH
DADR1
D/A converter data register ch.1
R/W
00003CH
DACR0
D/A control register 0
R/W
00003DH
DACR1
D/A control register 1
R/W
00003EH
CLKR
Clock output enable register
R/W
00003FH
24
0 0 0 0 1 – 0 0B
Communications
prescaler
register 0
000031H
000033H
X X X X X X X XB
(Disabled)
00002BH
to
00002FH
000032H
UART1
(SCI)
Initial value
0 0 0 0 0 0 0 0B
8/10-bit A/D
converter
8-bit D/A
converter
0 0 0 0 0 0 0 0B
X X X X X X X XB
– – – – – – – 0B
– – – – – – – 0B
Clock monitor
function
– – – – 0 0 0 0B
(Disabled)
000040H
PRLL0
PPG0 reload register L ch.0
R/W
000041H
PRLH0
PPG0 reload register H ch.0
R/W
8/16-bit PPG
timer 0
X X X X X X X XB
X X X X X X X XB
(Continued)
MB90570 Series
Address
Abbreviated
register
name
000042H
PRLL1
PPG1 reload register L ch.1
R/W
000043H
PRLH1
PPG1 reload register H ch.1
R/W
000044H
PPGC0
PPG0 operating mode control
register ch.0
R/W
8/16-bit PPG
timer 0
0 X 0 0 0 X X 1B
000045H
PPGC1
PPG1 operating mode control
register ch.1
R/W
8/16-bit PPG
timer 1
0 X 0 0 0 0 0 1B
000046H
PPGOE
PPG0 and 1 output control registers
ch.0 and ch.1
R/W
8/16-bit PPG
timer 0, 1
0 0 0 0 0 0 X XB
Read/
write
Register name
000047H
Resource name
Initial value
8/16-bit PPG
timer 1
X X X X X X X XB
X X X X X X X XB
(Disabled)
000048H
SMCSL0
Serial mode control lower status
register 0
R/W
000049H
SMCSH0
Serial mode control upper status
register 0
R/W
00004AH
SDR0
Serial data register 0
R/W
X X X X X X X XB
– – – – 0 0 0 0B
00004BH
SMCSL1
Serial mode control lower status
register 1
R/W
00004DH
SMCSH1
Serial mode control upper status
register 1
R/W
00004EH
SDR1
Serial data register 1
R/W
00004FH
000051H
000052H
000053H
000054H
000057H
000058H
IPCP0
ICU data register ch.0
IPCP1
ICU data register ch.1
ICS01
ICU control status register
00005BH
00005CH
00005DH
00005EH
00005FH
Extended I/O
serial interface 1
0 0 0 0 0 0 1 0B
X X X X X X X XB
X X X X X X X XB
R
R
16-bit I/O timer
(input capture
(ICU) section)
R/W
X X X X X X X XB
X X X X X X X XB
X X X X X X X XB
0 0 0 0 0 0 0 0B
(Disabled)
TCDT
Free run timer data register
R/W
TCCS
Free run timer control status register
R/W
000059H
00005AH
0 0 0 0 0 0 1 0B
(Disabled)
000055H
000056H
Extended I/O
serial interface 0
(Disabled)
00004CH
000050H
– – – – 0 0 0 0B
16-bit I/O timer
(16-bit free run
timer section)
0 0 0 0 0 0 0 0B
0 0 0 0 0 0 0 0B
0 0 0 0 0 0 0 0B
(Disabled)
OCCP0
OCU compare register ch.0
X X X X X X X XB
R/W
OCCP1
OCU compare register ch.1
R/W
OCCP2
OCU compare register ch.2
R/W
X X X X X X X XB
16-bit I/O timer
(output compare
(OCU) section)
X X X X X X X XB
X X X X X X X XB
X X X X X X X XB
X X X X X X X XB
(Continued)
25
MB90570 Series
Address
000060H
000061H
Abbreviated
register
name
OCCP3
Read/
write
Register name
OCU compare register ch.3
Resource name
Initial value
X X X X X X X XB
R/W
X X X X X X X XB
16-bit I/O timer
(output compare
(OCU) section)
000062H
OCS0
OCU control status register ch.0
R/W
000063H
OCS1
OCU control status register ch.1
R/W
000064H
OCS2
OCU control status register ch.2
R/W
0 0 0 0 – – 0 0B
000065H
OCS3
OCU control status register ch.3
R/W
– – – 0 0 0 0 0B
R
0 0 0 0 0 0 0 0B
000066H
000069H
00006AH
00006BH
00006CH
– – – 0 0 0 0 0B
(Disabled)
000067H
000068H
0 0 0 0 – – 0 0B
IBSR
IBCR
ICCR
IADR
IDAR
I2C bus status register
2
I C bus control register
R/W
0 0 0 0 0 0 0 0B
2
R/W
2
R/W
– X X X X X X XB
2
R/W
X X X X X X X XB
I C bus clock control register
I C bus address register
I C bus data register
00006DH
2
I C interface
– – 0 X X X X XB
(Disabled)
00006EH
00006FH
ROMM
ROM mirroring function selection
register
W
000070H
UDCR0
Up/down count register 0
R
000071H
UDCR1
Up/down count register 1
R
ROM mirroring
function
selection module
– – – – – – – 1B
0 0 0 0 0 0 0 0B
0 0 0 0 0 0 0 0B
8/16-bit up/down
counter/timer
000072H
RCR0
Reload compare register 0
W
000073H
RCR1
Reload compare register 1
W
0 0 0 0 0 0 0 0B
000074H
CSR0
Counter status register 0
R/W
0 0 0 0 0 0 0 0B
(Reserved area)*3
000075H
000076H
CCRL0
000077H
CCRH0
000078H
CSR1
Counter control register 0
R/W
Counter status register 1
R/W
000079H
(Reserved area)*
00007AH
CCRL1
00007BH
CCRH1
00007CH
– 0 0 0 0 0 0 0B
8/16-bit up/down
counter/timer
0 0 0 0 0 0 0 0B
0 0 0 0 0 0 0 0B
3
Counter control register 1
R/W
SMCSL2
Serial mode control lower status
register 2
R/W
00007DH
SMCSH2
Serial mode control higher status
register 2
R/W
00007EH
SDR2
Serial data register 2
R/W
00007FH
0 0 0 0 0 0 0 0B
8/16-bit up/down
counter/timer
– 0 0 0 0 0 0 0B
– 0 0 0 0 0 0 0B
– – – – 0 0 0 0B
Extended I/O
serial interface 2
0 0 0 0 0 0 1 0B
X X X X X X X XB
(Disabled)
(Continued)
26
MB90570 Series
Address
Abbreviated
register
name
000080H
CSCR0
Chip selection control register 0
R/W
– – – – 0 0 0 0B
000081H
CSCR1
Chip selection control register 1
R/W
– – – – 0 0 0 0B
000082H
CSCR2
Chip selection control register 2
R/W
Read/
write
Register name
Resource name
Initial value
– – – – 0 0 0 0B
Chip select
output
000083H
CSCR3
Chip selection control register 3
R/W
000084H
CSCR4
Chip selection control register 4
R/W
– – – – 0 0 0 0B
000085H
CSCR5
Chip selection control register 5
R/W
– – – – 0 0 0 0B
000086H
CSCR6
Chip selection control register 6
R/W
– – – – 0 0 0 0B
000087H
to
00008BH
– – – – 0 0 0 0B
(Disabled)
00008CH
RDR0
Port 0 input pull-up resistor setup
register
R/W
Port 0
0 0 0 0 0 0 0 0B
00008DH
RDR1
Port 1 input pull-up resistor setup
register
R/W
Port 1
0 0 0 0 0 0 0 0B
00008EH
RDR6
Port 6 input pull-up resistor setup
register
R/W
Port 6
0 0 0 0 0 0 0 0B
R/W
Address match
detection
function
0 0 0 0 0 0 0 0B
Delayed
interrupt
generation
module
– – – – – – – 0B
00008FH
to
00009DH
(Disabled)
PACSR
Program address detection control
status register
00009FH
DIRR
Delayed interrupt factor generation/
cancellation register
R/W
0000A0H
LPMCR
Low-power consumption mode
control register
R/W
0000A1H
CKSCR
Clock select register
R/W
00009EH
0000A2H
to
0000A4H
Low-power
consumption
(standby) mode
0 0 0 1 1 0 0 0B
1 1 1 1 1 1 0 0B
(Disabled)
0000A5H
ARSR
Automatic ready function select
register
W
0000A6H
HACR
Upper address control register
W
0000A7H
ECSR
Bus control signal select register
W
0000A8H
WDTC
Watchdog timer control register
R/W
Watchdog timer
X X X X X X X XB
0000A9H
TBTC
Timebase timer control register
R/W
Timebase timer
1 – – 0 0 1 0 0B
0000AAH
WTC
Clock timer control register
R/W
Clock timer
1 X 0 0 0 0 0 0B
0 0 1 1 – – 0 0B
External bus pin
0 0 0 0 0 0 0 0B
0 0 0 0 0 0 0 0B
(Continued)
27
MB90570 Series
(Continued)
Address
Abbreviated
register
name
Read/
write
Register name
0000ABH
to
0000ADH
0000AEH
Initial value
Flash interface
0 0 0 X 0 X X 0B
(Disabled)
FMCS
Flash control register
R/W
0000AFH
(Disabled)
0000B0H
ICR00
Interrupt control register 00
R/W
0 0 0 0 0 1 1 1B
0000B1H
ICR01
Interrupt control register 01
R/W
0 0 0 0 0 1 1 1B
0000B2H
ICR02
Interrupt control register 02
R/W
0 0 0 0 0 1 1 1B
0000B3H
ICR03
Interrupt control register 03
R/W
0 0 0 0 0 1 1 1B
0000B4H
ICR04
Interrupt control register 04
R/W
0 0 0 0 0 1 1 1B
0000B5H
ICR05
Interrupt control register 05
R/W
0 0 0 0 0 1 1 1B
0000B6H
ICR06
Interrupt control register 06
R/W
0 0 0 0 0 1 1 1B
0000B7H
ICR07
Interrupt control register 07
R/W
0000B8H
ICR08
Interrupt control register 08
R/W
0000B9H
ICR09
Interrupt control register 09
R/W
0 0 0 0 0 1 1 1B
0000BAH
ICR10
Interrupt control register 10
R/W
0 0 0 0 0 1 1 1B
0000BBH
ICR11
Interrupt control register 11
R/W
0 0 0 0 0 1 1 1B
0000BCH
ICR12
Interrupt control register 12
R/W
0 0 0 0 0 1 1 1B
0000BDH
ICR13
Interrupt control register 13
R/W
0 0 0 0 0 1 1 1B
0000BEH
ICR14
Interrupt control register 14
R/W
0 0 0 0 0 1 1 1B
0000BFH
ICR15
Interrupt control register 15
R/W
0 0 0 0 0 1 1 1B
0000C0H
to
0000FFH
(External area)*1
000100H
to
000###H
(RAM area)*2
000###H
to
001FEFH
(Reserved area)*3
001FF0H
001FF1H
PADR0
Program address detection register 0
R/W
Program address detection register 1
R/W
Interrupt
controller
0 0 0 0 0 1 1 1B
0 0 0 0 0 1 1 1B
X X X X X X X XB
X X X X X X X XB
Address match
detection
function
001FF2H
Program address detection register 2
R/W
001FF3H
Program address detection register 3
R/W
Program address detection register 4
R/W
X X X X X X X XB
Program address detection register 5
R/W
X X X X X X X XB
001FF4H
001FF5H
001FF6H
to
001FFFH
28
Resource name
PADR1
(Reserved area)
X X X X X X X XB
X X X X X X X XB
MB90570 Series
Descriptions for read/write
R/W : Readable and writable
R
: Read only
W : Write only
Descriptions for initial value
0
1
X
–
: The initial value of this bit is “0”.
: The initial value of this bit is “1”.
: The initial value of this bit is undefined.
: This bit is unused. The initial value is undefined.
*1 : This area is the only external access area having an address of 0000FFH or lower. An access operation to this
area is handled as that to external I/O area.
*2 : For details of the RAM area, see “■ MEMORY MAP”.
*3 : The reserved area is disabled because it is used in the system.
Notes : • For bits that is initialized by an reset operation, the initial value set by the reset operation is listed as an
initial value. Note that the values are different from reading results.
For LPMCR/CKSCR/WDTC, there are cases where initialization is performed or not performed, depending
on the types of the reset. However initial value for resets that initializes the value are listed.
• The addresses following 0000FFH are reserved. No external bus access signal is generated.
• Boundary ####H between the RAM area and the reserved area varies with the product model.
29
MB90570 Series
■ INTERRUPT FACTORS, INTERRUPT VECTORS, INTERRUPT CONTROL REGISTER
Interrupt vector
Interrupt control register
EI2OS
support
Number
Address
ICR
Address
Reset
×
# 08
FFFFDCH
—
—
INT9 instruction
×
# 09
FFFFD8H
—
—
Exception
×
# 10
FFFFD4H
—
—
8/10-bit A/D converter
# 11
FFFFD0H
Input capture 0 (ICU) include
# 12
FFFFCCH
ICR00
0000B0H
DTP0 (external interrupt 0)
# 13
FFFFC8H
Input capture 1 (ICU) include
# 14
FFFFC4H
ICR01
0000B1H
Output compare 0 (OCU) match
# 15
FFFFC0H
Output compare 1 (OCU) match
# 16
FFFFBCH
ICR02
0000B2H
Output compare 2 (OCU) match
# 17
FFFFB8H
Output compare 3 (OCU) match
# 18
FFFFB4H
ICR03
0000B3H
Extended I/O serial interface 0
# 19
FFFFB0H
# 20
FFFFACH
ICR04
0000B4H
# 21
FFFFA8H
# 22
FFFFA4H
ICR05
0000B5H
Extended I/O serial interface 2
# 23
FFFFA0H
DTP1 (external interrupt 1)
# 24
FFFF9CH
ICR06
0000B6H
DTP2/DTP3 (external interrupt 2/
external interrupt 3)
# 25
FFFF98H
ICR07
0000B7H
# 26
FFFF94H
# 27
FFFF90H
ICR08
0000B8H
# 28
FFFF8CH
8/16-bit up/down counter/timer 0
borrow/overflow/inversion
# 29
FFFF88H
8/16-bit up/down counter/timer 0
compare match
ICR09
0000B9H
# 30
FFFF84H
8/16-bit up/down counter/timer 1
borrow/overflow/inversion
# 31
FFFF80H
8/16-bit up/down counter/timer 1
compare match
# 32
FFFF7CH
DTP6 (external interrupt 6)
# 33
FFFF78H
# 34
FFFF74H
Interrupt source
16-bit free run timer
×
Extended I/O serial interface 1
Clock timer
8/16-bit PPG timer 0 counter borrow
×
×
DTP4/DTP5 (external interrupt 4/
external interrupt 5)
8/16-bit PPG timer 1 counter borrow
Timebase timer
×
Priority
High
0000BAH
ICR10
×
0000BAH
ICR11
0000BBH
Low
(Continued)
30
MB90570 Series
(Continued)
Interrupt source
EI2OS
support
Interrupt vector
Number
Address
# 35
FFFF70H
# 36
FFFF6CH
UART1 (SCI) reception complete
# 37
FFFF68H
UART1 (SCI) transmission
complete
# 38
FFFF64H
UART0 (SCI) reception complete
# 39
FFFF60H
UART0 (SCI) transmission
complete
# 40
FFFF5CH
DTP7 (external interrupt 7)
I2C interface
×
Flash memory
×
# 41
FFFF58H
Delayed interrupt generation
module
×
# 42
FFFF54H
Interrupt control register
ICR
Address
ICR12
0000BCH
ICR13
0000BDH
ICR14
0000BEH
ICR15
0000BFH
Priority
High
Low
:Can be used
× :Can not be used
:Can be used. With EI2OS stop function.
31
MB90570 Series
■ PERIPHERALS
1. I/O Port
(1) Input/output Port
Port 0 through 4, 6, 8, A and B are general-purpose I/O ports having a combined function as an external bus
pin and a resource input. Port 0 to Port 3 have a general-purpose I/O ports function only in the single-chip mode.
• Operation as output port
The pin is configured as an output port by setting the corresponding bit of the DDR register to “1”.
Writing data to PDR register when the port is configured as output, the data is retained in the output latch in
the PDR and directly output to the pin.
The value of the pin (the same value retained in the output latch of PDR) can be read out by reading the PDR
register.
Note : When a read-modify-write instruction (e.g. bit set instruction) is performed to the port data register, the
destination bit of the operation is set to the specified value, not affecting the bits configured by the DDR
register for output, however, values of bits configured by the DDR register as inputs are changed because
input values to the pins are written into the output latch. To avoid this situation, configure the pins by the DDR
register as output after writing output data to the PDR register when configuring the bit used as input as
outputs.
• Operation as input port
The pin is configured as an input by setting the corresponding bit of the DDR register to “0”.
When the pin is configured as an input, the output buffer is turned-off and the pin is put into a high-impedance
status.
When a data is written into the PDR register, the data is retained in the output latch of the PDR, but pin outputs
are unaffected.
Reading the PDR register reads out the pin level (“0” or “1”).
32
MB90570 Series
(2) Register Configuration
• Port 0 data register (PDR0)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000000H
(PDR1)
P07
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
P06
P05
P04
P03
P02
P01
P00
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 1 data register (PDR1)
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
Address bit 15
000001H
P17
bit 14
P16
P15
P14
P13
P12
P11
P10
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
(PDR0)
• Port 2 data register (PDR2)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000002H
(PDR3)
P27
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
P26
P25
P24
P23
P22
P21
P20
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 3 data register (PDR3)
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
Address bit 15
000003H
P37
bit 14
P36
P35
P34
P33
P32
P31
P30
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
(PDR2)
• Port 4 data register (PDR4)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000004H
(PDR5)
P47
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
P46
P45
P44
P43
P42
P41
P40
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 5 data register (PDR5)
Address bit 15
000005H
P57
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
P56
P55
P54
P53
P52
P51
P50
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
(PDR4)
• Port 6 data register (PDR6)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000006H
(PDR7)
P67
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
P66
P65
P64
P63
P62
P61
P60
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 7 data register (PDR7)
Address bit 15
000007H
—
—
bit 14
—
—
bit 13
—
—
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
P74
P73
P72
P71
P70
R/W
R/W
R/W
R/W
R/W
Initial value
- - - XXXXX B
(PDR6)
• Port 8 data register (PDR8)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000008H
(PDR9)
P87
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
P86
P85
P84
P83
P82
P81
P80
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(Continued)
33
MB90570 Series
• Port 9 data register (PDR9)
Address
000009H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
P97
P96
P95
P94
P93
P92
P91
P90
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
(PDR8)
• Port A data register (PDRA)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00000AH
(PDRB)
PA7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
PA6
PA5
PA4
PA3
PA2
PA1
PA0
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00000BH
(PDRA)
PB7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
PB6
PB5
PB4
PB3
PB2
PB1
PB0
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00000CH
(Disabled)
—
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
—
—
—
PC3
PC2
PC1
PC0
XXXXXXXX B
—
—
—
—
R/W
R/W
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000010H
(DDR1)
D07
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D06
D05
D04
D03
D02
D01
D00
00000000 B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port B data register (PDRB)
• Port C data register (PDRC)
• Port 0 direction register (DDR0)
• Port 1 direction register (DDR1)
Address
000011H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
D17
D16
D15
D14
D13
D12
D11
D10
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
(DDR0)
• Port 2 direction register (DDR2)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000012H
(DDR3)
D27
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D26
D25
D24
D23
D22
D21
D20
00000000 B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 3 direction register (DDR3)
Address
000013H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
D37
D36
D35
D34
D33
D32
D31
D30
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
(DDR2)
• Port 4 direction register (DDR4)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000014H
(DDR5)
D47
bit 6
D46
D45
D44
D43
D42
R/W
R/W
R/W
R/W
R/W
R/W
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D41
D40
00000000 B
R/W
R/W
(Continued)
34
MB90570 Series
• Port 5 direction register (DDR5)
Address
000015H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
D57
D56
D55
D54
D53
D52
D51
D50
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
(DDR4)
• Port 6 direction register (DDR6)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000016H
(DDR7)
D67
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D66
D65
D64
D63
D62
D61
D60
00000000 B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 7 direction register (DDR7)
Address
000017H
bit 15
bit 14
—
—
—
—
bit 13
—
—
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
D74
D73
D72
D71
D70
R/W
R/W
R/W
R/W
R/W
Initial value
- - - 00000 B
(DDR6)
• Port 8 direction register (DDR8)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000018H
(DDR9)
D87
bit 6
D86
D85
D84
D83
D82
R/W
R/W
R/W
R/W
R/W
R/W
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D81
D80
00000000 B
R/W
R/W
• Port 9 direction register (DDR9)
Address bit 15
000019H
D97
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
D96
D95
D94
D93
D92
D91
D90
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
(DDR8)
• Port A direction register (DDRA)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00001AH
(DDRB)
DA7
bit 6
DA6
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00001BH
(DDRA)
DB7
bit 6
bit 5
DB6
DB5
R/W
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00001CH
(ODR4)
—
bit 6
bit 5
—
—
—
bit 5
bit 4
bit 3
DA5
DA4
DA3
R/W
R/W
R/W
bit 4
bit 3
DB4
R/W
bit 4
—
—
bit 2
bit 1
bit 0
Initial value
DA2
DA1
DA0
00000000 B
R/W
R/W
R/W
bit 2
bit 1
bit 0
Initial value
DB3
DB2
DB1
DB0
00000000 B
R/W
R/W
R/W
R/W
bit 3
bit 2
bit 1
bit 0
Initial value
—
DC3
DC2
DC1
DC0
00000000 B
—
R/W
R/W
R/W
R/W
• Port B direction register (DDRB)
• Port C direction register (DDRC)
• Port 4 output pin register (ODR4)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
00001DH
(DDRC)
OD47 OD46
R/W
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
OD45
OD44
OD43
OD42
OD41
OD40
00000000 B
R/W
R/W
R/W
R/W
R/W
R/W
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
RD06
RD05
RD04
RD03
RD02
RD01
RD00
00000000 B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• Port 0 input pull-up resistor setup register (RDR0)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00008CH
(RDR1)
RD07
R/W
(Continued)
35
MB90570 Series
(Continued)
• Port 1 input pull-up resistor setup register (RDR1)
Address
00008DH
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
RD17
RD16
RD15
RD14
RD13
RD12
RD11
RD10
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
(RDR0)
• Port 6 input pull-up resistor setup register (RDR6)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00008EH
(Disabled)
RD67
R/W
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
RD66
RD65
RD64
RD63
RD62
RD61
RD60
00000000 B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
11111111 B
• Analog input enable register (ADER)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00001EH
(Disabled)
ADE7
R/W
R/W:Readable and writable
—:Reserved
X:Undefined
36
ADE6 ADE5
ADE4 ADE3
ADE2
ADE1
ADE0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MB90570 Series
(3) Block Diagram
• Input/output port
PDR (port data register)
Internal data bus
PDR read
Output latch
P-ch
PDR write
Pin
DDR (port direction register)
N-ch
Direction latch
DDR write
Standby control (SPL=1)
DDR read
Standby control: Stop, timebase timer mode and SPL=1, or hardware standby mode
• Output pin register (ODR)
To resource input
PDR (port data register)
From resource output
Resource output enable
PDR read
P-ch
Output latch
PDR write
Pin
Internal data bus
DDR (port direction register)
N-ch
Direction latch
DDR write
Standby control
(SPL=1)
DDR read
ODR (output pin register)
ODR latch
ODR write
ODR read
Standby control: Stop, timebase timer mode and SPL=1, or hardware standby mode
37
MB90570 Series
• Input pull-up resistor setup register (RDR)
To resource input
PDR (port data register)
Pull-up resistor
About 5.0 kΩ
(5.0 V)
PDR read
Output latch
P-ch
P-ch
PDR write
Pin
Internal data bus
DDR (port direction register)
N-ch
Direction latch
DDR write
Standby control
(SPL=1)
DDR read
RDR latch
RDR write
RDR
(input pull-up resistor setup register)
RDR read
Standby control: Stop, timebase timer mode and SPL=1
• Analog input enable register (ADER)
ADER (analog input enable register)
ADER read
ADER latch
To analog input
ADER write
Internal data bus
PDR (port data register)
PDR read
RMW
(read-modify-write
type instruction)
Output latch
P-ch
PDR write
Pin
DDR (port direction register)
Direction latch
N-ch
DDR write
DDR read
Standby control: Stop, timebase timer mode and SPL=1
38
Standby control
(SPL=1)
MB90570 Series
2. Timebase Timer
The timebase timer is a 18-bit free run counter (timebase counter) for counting up in synchronization to the
internal count clock (divided-by-2 of oscillation) with an interval timer function for selecting an interval time from
four types of 212/HCLK, 214/HCLK, 216/HCLK, and 219/HCLK.
The timebase timer also has a function for supplying operating clocks for the timer output for the oscillation
stabilization time or the watchdog timer etc.
(1) Register Configuration
• Timebase timer control register (TBTC)
Address
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
0000A9H
RESV
—
—
TBIE
TBOF
—
—
—
R/W
R/W
bit 9
bit 8
TBR
TBC1
TBC0
W
R/W
R/W
bit 7 . . . . . . . . . . . .bit 0
(WDTC)
Initial value
1--00100B
R/W:Readable and writable
W:Write only
—:Unused
RESV: Reserved bit
(2) Block Diagram
To watchdog timer
To 8/16-bit PPG timer
Timebase timer counter
Divided-by-2
of HCLK
× 21 × 22 × 2 3
...
...
× 28 × 29 × 210 × 211 × 212 × 213 × 214 × 215 × 216 × 217 × 218
OF
OF
OF
OF
To oscillation stabilization
time selector of clock control block
Power-on reset
Start stop mode
CKSCR: MCS = 1→0*1
Counter
clear circuit
Interval
timer selector
Set TBOF
Clear TBOF
Timebase timer control register
(TBTC)
RESV
—
—
TBIE TBOF TBR
TBC1 TBC0
Timebase timer
interrupt signal
#34*2
OF: Overflow
HCLK: Oscillation clock
*1: Switch machine clock from oscillation clock to PLL clock
*2: Interrupt signal
39
MB90570 Series
3. Watchdog Timer
The watchdog timer is a 2-bit counter operating with an output of the timebase timer and resets the CPU when
the counter is not cleared for a preset period of time.
(1) Register Configuration
• Watchdog timer control register (WDTC)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
bit 5
bit 4
0000A8H
(TBTC)
PONR STBR WRST ERST
R
R
R
bit 3
bit 2
bit 1
bit 0
SRST
WTE
WT1
WT0
R
W
W
W
R
Initial value
XXXXXXXX B
R:Read only
W:Write only
X:Indeterminate
(2) Block Diagram
Watchdog timer control register (WDTC)
PONR STBR WRST ERST SRST WTE WT1
WT0
2
Watchdog timer
CLR and start
Overflow
Start sleep mode
Start hold status
Start stop mode
Counter clear
control circuit
Count clock
selector
2-bit
counter
CLR
Watchdog timer
reset generation
circuit
CLR
4
Clear
(Timebase timer counter)
Divided-by-2
of HCLK
× 21 × 22
HCLK: Oscillation clock
40
...
× 28 × 29 × 210 × 211 × 212 × 213 × 214 × 215 × 216 × 217 × 218
To internal reset
generation circuit
MB90570 Series
4. 8/16-bit PPG Timer
The 8/16-bit PPG timer is a 2-CH reload timer module for outputting pulse having given frequencies/duty ratios.
The two modules performs the following operation by combining functions.
• 8-bit PPG output 2-CH independent operation mode
This is a mode for operating independent 2-CH 8-bit PPG timer, in which PPG0 and PPG1 pins correspond
to outputs from PPG0 and PPG1 respectively.
• 16-bit PPG timer output operation mode
In this mode, PPG0 and PPG1 are combined to be operated as a 1-CH 8/16-bit PPG timer operating as a 16bit timer. Because PPG0 and PPG1 outputs are reversed by an underflow from PPG1 outputting the same
output pulses from PPG0 and PPG1 pins.
• 8 + 8-bit PPG timer output operation mode
In this mode, PPG0 is operated as an 8-bit communications prescaler, in which an underflow output of PPG0
is used as a clock source for PPG1. A toggle output of PPG0 and PPG output of PPG1 are output from PPG0
and PPG1 respectively.
• PPG output operation
A pulse wave with any period/duty ratio is output. The module can also be used as a D/A converter with an
external add-on circuit.
41
MB90570 Series
(1) Register Configuration
• PPG0 operating mode control register ch.0 (PPGC0)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000044H
(PPGC1)
PEN0
R/W
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
—
PE00
PIE0
PUF0
—
—
RESV
0X0 0 0XX1 B
—
R/W
R/W
R/W
—
—
—
• PPG1 operating mode control register ch.1 (PPGC1)
Address bit 15 bit 14
000045H
PEN1
—
R/W
R/W
bit 13
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
bit 12
bit 11
PEI0
PIE1
PUF1
MD1
MD0
RESV
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
0X0 0 0 0 0 1 B
(PPGC0)
• PPG0, 1 output control register ch.0, ch.1(PPGOE)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
000046H
(Disabled)
PCS2 PCS1
R/W
R/W
bit 5
bit 4
PCS0
PCM2 PCM1 PCM0
R/W
R/W
bit 3
R/W
bit 2
R/W
bit 1
bit 0
Initial value
—
—
0 0 0 0 0 0XX B
—
—
• PPG0 reload register H ch.0 (PRLH0)
Address bit 15
000041H
bit 14
R/W
R/W
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
(PRLL0)
R/W
R/W
R/W
R/W
bit 12
bit 11
bit 10
R/W
R/W
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
Initial value
XXXXXXXX B
• PPG1 reload register H ch.1 (PRLH1)
Address bit 15
000043H
bit 14
R/W
R/W
bit 13
(PRLL1)
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
R/W
• PPG0 reload register L ch.0 (PRLL0)
Address
bit 15 . . . . . . . . . . . . bit 8 bit 7
000040H
(PRLH0)
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000042H
(PRLH1)
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
• PPG1 reload register L ch.1 (PRLL1)
R/W:Readable and writable
—:Reserved
X:Undefined
RESV: Reserved bit
42
Initial value
XXXXXXXX B
MB90570 Series
(2) Block Diagram
• Block diagram of 8/16-bit PPG timer (ch.0)
Data bus for “H” digits
Data bus for “L” digits
PPG0 reload
register
PRLH0
PPG0 output
control register
ch.0 (PPGOE0)
PPG0 operating mode
control register ch.0 (PPGC0)
PEN0
PRLL0
—
PE00 PIE0 PUF0
—
—
RESV
PCM2 PCM1 PCM0
R
Temporary buffer
(PRLBH0)
S
Interrupt request
#26*
Q
2
Reload register
(L/H selector)
Mode control signal
Select signal
PPG1 underflow
PPG0 underflow
(to PPG1)
Count value
Re-load
Clear
Pulse selector
Down counter
(PCNT0)
Underflow
CLK
Reverse
PPG0
output latch
Pin
P46/PPG0
Timebase timer output (512/HCLK)
Peripheral clock (16/φ)
Peripheral clock (8/φ)
Peripheral clock (4/φ)
Peripheral clock (2/φ)
Peripheral clock (1/φ)
PPG output
control circuit
Count
clock
selector
3
Select signal
*:Interrupt number
HCLK:Oscillation clock
φ:Machine clock frequency
43
MB90570 Series
• Block diagram of 8/16-bit PPG timer (ch.1)
Data bus for “H” digits
Data bus for “L” digits
PPG1 reload
register
PRLL1
PRLH1
PEI0 PIE1 PUF1 MD1 MD0 RESV PCS2 PCS1 PCS0
PEN1 —
Operating mode
control signal
2
R
Temporary buffer
(PRLBH1)
Count value
Select signal
Re-load
Down counter
(PCNT1)
PPG1 underflow
(to PPG0)
Interrupt request
#28*
S Q
Reload selector
(L/H selector)
Clear
Underflow
Reverse
PPG1
output latch
CLK
MD0
PPG output control circuit
Timebase timer output (512/HCLK)
Peripheral clock (16/φ)
Peripheral clock (8/φ)
Peripheral clock (4/φ)
Peripheral clock (2/φ)
Peripheral clock (1/φ)
Count clock selector
Select signal
*:Interrupt number
HCLK:Oscillation clock
φ:Machine clock frequency
Pin
P47/PPG1
PPG0 underflow
44
PPG1 output control
register ch.1 (PPGOE1)
PPG1 operating mode
control register ch.1 (PPGC1)
MB90570 Series
5. 16-bit I/O timer
The 16-bit I/O timer module consists of one 16-bit free run timer, two input capture circuits, and four output
comparators. This module allows two independent waveforms to be output on the basis of the 16-bit free run
timer. Input pulse width and external clock periods can, therefore, be measured.
• Block Diagram
Internal data bus
Input capture
Dedicated
bus
16-bit
free run timer
Dedicated
bus
Output compare
45
MB90570 Series
(1) 16-bit free run Timer
The 16-bit free run timer consists of a 16-bit up counter, a control register, and a communications prescaler
register. The value output from the timer counter is used as basic timer (base timer) for input capture (ICU) and
output compare (OCU).
• A counter operation clock can be selected from four internal clocks (φ/4, φ/16, φ/32 and φ/64).
• An interrupt can be generated by overflow of counter value or compare match with OCU compare register 0.
(Compare match requires mode setup.)
• The counter value can be initialized to “0000H” by a reset, software clear or compare match with OCU compare
register 0.
• Register Configuration
• free run timer data register (TCDT)
Address
000056H
000057H
bit 15 bit 14bit 13bit 12bit 11bit 10 bit 9 bit 8 bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
T15 T14 T13 T12 T11 T10
T9
T8
T7
T6
T5
T4
T3
T2
T1
T0
Initial value
00000000B
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
• free run timer control status register (TCCS)
bit 15. . . . . . . . . . . . .bit 8 bit 7
Address
000058H
(Disabled)
bit 6
bit 5
bit 4
RESV
IVF
IVFE
STOP MODE
R/W
R/W
R/W
R/W
bit 3
R/W
bit 2
bit 1
bit 0
Initial value
CLR
CLK1
CLK0
00000000B
R/W
R/W
R/W
R/W: Readable and writable
RESV: Reserved bit
• Block Diagram
Count value output
to ICO and OCU
free run timer data register (TCDT)
OF
16-bit counter
φ
STOP
CLR
Communications
prescaler register
OCU compare register
ch.0 match signal
2
free run timer
control status register
(TCCS)
RESV
IVF
IVFE STOP MODE CLR CLK1 CLK0
16-bit free run timer
interrupt request
#20*
*:Interrupt number
φ:Machine clock frequency
OF:Overflow
46
Internal data bus
CLK
MB90570 Series
(2) Input Capture (ICU)
The input capture (ICU) generates an interrupt request to the CPU simultaneously with a storing operation of
current counter value of the 16-bit free run timer to the ICU data register (IPCP) upon an input of a trigger edge
to the external pin.
There are four sets (four channels) of the input capture external pins and ICU data registers, enabling measurements of maximum of four events.
• The input capture has two sets of external input pins (IN0, IN1) and ICU registers (IPCP), enabling measurements of maximum of four events.
• A trigger edge direction can be selected from rising/falling/both edges.
• The input capture can be set to generate an interrupt request at the storage timing of the counter value of the
16-bit free run timer to the ICU data register (IPCP).
• The input compare conforms to the extended intelligent I/O service (EI2OS).
• The input capture (ICU) function is suited for measurements of intervals (frequencies) and pulse widths.
• Register Configuration
• ICU data register ch.0, ch.1 (IPCP0, IPCP1)
Address
IPCP0(high): 000051H
IPCP1(high): 000053H
Address
IPCP0(low): 000050H
IPCP1(low): 000052H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . . bit 0
CP15
CP14
CP13
CP12
CP11
CP10
CP09
CP08
R
R
R
R
R
R
R
R
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
CP06
CP05
CP04
CP03
CP02
CP01
CP00
R
R
R
R
R
R
R
bit 15. . . . . . . . . . . . bit 8
(IPCP0 high, IPCP1 high) CP07
R
(IPCP0 low, IPCP1 low)
Initial value
XXXXXXXXB
Initial value
XXXXXXXXB
Note: This register holds a 16-bit free run timer value when the valid edge of the corresponding external pin input waveform is
detected. (You can word-access this register, but you cannot program it.)
• ICU control status register (ICS01)
Address
000054H
bit 15. . . . . . . . . . . . bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
(Disabled)
ICP1
ICP0
ICE1
ICE0
EG11
EG10
EG01 EG00
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 0
Initial value
00000000B
R/W
R/W:Readable and writable
R:Read only
X:Undefined
47
MB90570 Series
• Block Diagram
Internal data bus
Latch
signal
Output latch
ICU data register (IPCP)
Edge detection circuit
P56/IN0
Pin
P57/IN1
Data latch signal
IPCP0H
IPCP0L
2
Pin
16-bit free run
IPCP1H
IPCP1L
2
ICU control status register (ICS01)
ICP1 ICP0 ICE1 ICE0 EG11 EG10 EG01 EG00
Interrupt request
#12*
Interrupt request
#14*
*: Interrupt number
48
16
16
MB90570 Series
(3) Output Compare (OCU)
The output compare (OCU) is two sets of compare units consisting of four-channel OCU compare registers, a
comparator and a control register.
An interrupt request can be generated for each channel upon a match detection by performing time-division
comparison between the OCU compare data register setting value and the counter value of the 16-bit free run
timer.
The OUT pin can be used as a waveform output pin for reversing output upon a match detection or a generalpurpose output port for directly outputting the setting value of the CMOD bit.
• Register Configuration
• OCU control status register ch.1, ch.3 (OCS1, OCS3)
Address
bit 15
bit 14
bit 13
000063H
000065H
—
—
—
—
—
—
bit 12
bit 11
bit 10
CMOD OTE1
R/W
bit 9
OTE0 OTD1
R/W
R/W
R/W
bit 8 bit 7 . . . . . . . . . . . . . bit 0
OTD0
(OCS0, OCS2)
Initial value
- - - 00000 B
R/W
• OCU control status register ch.0, ch.2 (OCS0, OCS2)
Address
000062H
000064H
bit 15. . . . . . . . . . . . bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
(OCS1, OCS3)
ICP1
ICP0
ICE1
ICE0
—
—
CST1
CST0
0000 - - 00 B
R/W
R/W
R/W
R/W
—
—
R/W
R/W
bit 10
bit 9
• OCU compare register ch.0 to ch.3 (OCCP0 to OCCP3)
Address
OCCP0 (high order address): 00005BH
OCCP1 (high order address): 00005DH
OCCP2 (high order address): 00005FH
OCCP3 (high order address): 000061H
Address
OCCP0 (low order address): 00005AH
OCCP1 (low order address): 00005CH
OCCP2 (low order address): 00005EH
OCCP3 (low order address): 000060H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 8
Initial value
XXXXXXXXB
C15
C14
C13
C12
C11
C10
C09
C08
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
XXXXXXXXB
C07
C06
C05
C04
C03
C02
C01
C00
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W:Readable and writable
—:Reserved
X:Undefined
49
MB90570 Series
• Block diagram
#16*
OCU control
status register ch.0, ch.1 (OCS0, OCS1)
—
—
—
Output compare
interrupt request
#15*
CMOD OTE1 OTE0 OTD1 OTD0 ICP1 ICP0
ICE1
ICE0
—
—
CST1 CST0
2
2
16-bit free run timer
Compare control circuit 3
OCCP3
OCU compare register ch.3
Internal data bus
Compare control circuit 2
P67/OUT3
Output
control circuit 3
OCCP2
Pin
OCU compare register ch.2
P66/OUT2
Output
control circuit 2
Pin
Compare control circuit 1
P65/OUT1
OCCP1
Output
control circuit 1
Pin
OCU compare register ch.1
P64/OUT0
Output
control circuit 0
Compare control circuit 0
Pin
OCCP0
OCU compare register ch.0
2
2
OCU control status register
ch.2, ch.3 (OCS2, OCS3)
—
—
—
CMOD OTE1 OTE0 OTD1 OTD0 ICP1
ICP0
ICE1
ICE0
—
—
CST1 CST0
#18*
#17*
*: Interrupt number
50
Output compare
interrupt request
MB90570 Series
6. 8/16-bit up/down counter/timer
The 8/16-bit up/down counter/timer consists of six event input pins, two 8-bit up/down counters, two 8-bit
reload compare registers, and their controllers.
(1) Register configuration
• Up/down count register 0 (UDCR0)
Address
bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D07
D06
D05
D04
D03
D02
D01
D00
00000000 B
R
R
R
R
R
R
R
R
000070H
(UDCR1)
• Up/down count register 1 (UDCR1)
Address
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . . bit 0
Initial value
000071H
D17
D16
D15
D14
D13
D12
D11
D10
(UDCR0)
00000000 B
R
R
R
R
R
R
R
R
• Reload compare register 0 (RCR0)
Address
bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D07
D06
D05
D04
D03
D02
D01
D00
00000000 B
W
W
W
W
W
W
W
W
(RCR1)
000072H
• Reload compare register 1 (RCR1)
Address
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . . bit 0
Initial value
000073H
D17
D16
D15
D14
D13
D12
D11
D10
(RCR0)
00000000 B
W
W
W
W
W
W
W
W
• Counter status register 0, 1 (CSR0, CSR1)
Address
000074H
000078H
bit 15 . . . . . . . . . . . . bit 8 bit 7
(Reserved area)
bit 6
bit 5
bit 4
CSTR
CITE
UDIE
CMPF
R/W
R/W
R/W
bit 3
bit 2
bit 1
OVFF UDFF UDF1
bit 0
Initial value
UDF0
00000000 B
R/W
R/W
R/W
R
R
bit 4
bit 3
bit 2
bit 1
bit 0
• Counter control register 0, 1 (CCRL0, CCRL1)
Address
000076H
00007AH
bit 15 . . . . . . . . . . . . bit 8 bit 7
(CCRH0, CCRH1)
—
—
bit 6
bit 5
CTUT UCRE RLDE UDCC CGSC CGE1 CGE0
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
- 0000000 B
R/W
• Counter control register 0 (CCRH0)
Address
bit 15
000077H
bit 14
bit 13
bit 12
M16E CDCF
CFIE
CLKS CMS1 CMS0 CES1 CES0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 11
bit 10
bit 9
bit 8
R/W
bit 11
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . . bit 0
Initial value
(CCRL0)
00000000 B
bit 7 . . . . . . . . . . . . . bit 0
Initial value
(CCRL1)
- 0000000 B
• Counter control register 1 (CCRH1)
Address
bit 15
bit 14
bit 13
bit 12
00007BH
—
CDCF
CFIE
CLKS CMS1 CMS0 CES1 CES0
—
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W:Readable and writable
R:Read only
W:Write only
—:Undefined
51
MB90570 Series
(2) Block Diagram
• Block diagram of 8/16-bit up/down counter/timer 0
Internal data bus
RCR0
Reload compare register 0
Re-load
control
circuit
UDCR0
CARRY/
BORRW
Up/down count register 0
(to channel 1)
Counter control
register 0 (CCRL0)
Counter clear
circuit
PA2/ZIN0
Pin
Edge/level
detection circuit
φ
Prescaler
PA0/AIN0/IRQ6
Pin
Underflow
CTUT UCRE RLDE UDCC CGSC CGE1 CGE0
Overflow
—
Compare
control circuit
Count clock
Counter status
register 0 (CSR0)
UP/down count
clock selector
CSTR CITE UDIE CMPF OVFF UDFF UDF1 UDF0
Pin
PA1/BIN0
Interrupt request
#29*
Interrupt request
#30*
M16E CDCF CFIE CLKS CMS1 CMS0 CES1 CES0
Counter control register 0 (CCRH0)
*:Interrupt number
φ:Machine clock frequency
52
M16E
(to channel 1)
MB90570 Series
• Block diagram of 8/16-bit up/down counter/timer 1
Internal data bus
RCR1
Reload compare register 1
Re-load
control
circuit
UDCR1
Up/down count register 1
Counter control
register 1 (CCRL1)
PA5/ZIN1
Counter clear
circuit
Edge/level
detection circuit
Pin
CARRY/BORRW
(from channel 0)
Prescaler
Pin
Compare
control circuit
Count clock
Counter status
register 1 (CSR1)
φ
PA3/AIN1/IRQ7
Underflow
CTUT UCRE RLDE UDCC CGSC CGE1 CGE0
Overflow
—
UP/down count
clock selector
CSTR CITE UDIE CMPF OVFF UDFF UDF1 UDF0
Pin
PA4/BIN1
M16E
(from channel 1)
Interrupt request
#31*
Interrupt request
#32*
—
CDCF CFIE CLKS CMS1 CMS0 CES1 CES0
Counter control register 1 (CCRH1)
*:Interrupt number
φ:Machine clock frequency
53
MB90570 Series
7. Extended I/O serial interface
The extended I/O serial interface transfers data using a clock synchronization system having an 8-bit x 1 channel
configuration.
For data transfer, you can select LSB first/MSB first.
(1) Register Configuration
• Serial mode control upper status register 0 to 2 (SMCSH0 to SMCSH2)
Address
SMCSH0: 000049H
SMCSH1: 00004DH
SMCSH2: 00007DH
bit 15
bit 14
bit 13
SMD2 SMD1 SMD0
R/W
R/W
R/W
bit 12
bit 11
SIE
SIR
R/W
R/W
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . . bit 0
Initial value
(SMCSL)
00000010 B
BUSY STOP STRT
R
R/W
R/W
• Serial mode control lower status register 0 to 2 (SMCSL0 to SMCSL2)
Address
SMCSL0: 000048H
SMCSL1: 00004CH
SMCSL2: 00007CH
bit 15 . . . . . . . . . . . . bit 8 bit 7
Address
SDR0: 00004AH
SDR1: 00004EH
SDR2: 00007EH
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
—
—
—
—
• Serial data register 0 to 2 (SDR0 to SDR2)
—
—
—
—
MODE
BDS
SOE
SCOE
- - - - 0000 B
R/W
R/W
R/W
R/W
bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
D7
D6
D5
D4
D3
D2
D1
D0
XXXXXXXX B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(SMCSH)
(Disabled)
R/W:Readable and writable
R:Read only
—:Reserved
X:Undefined
54
MB90570 Series
(2) Block Diagram
Internal data bus
(MSB first) D0 to D7
D7 to D0 (LSB first)
Pin
P40/SIN0
Transfer direction selection
Pin
Read
Write
Serial data register
(SDR)
P43/SIN1
Pin
P41/SOT0
Pin
Pin
P50/SIN2
P44/SOT1
Pin
P51/SOT2
Pin
P45/SCK1
Shift clock counter
Control circuit
Pin
P52/SCK2
Pin
P42/SCK0
Internal clock
2
1
0
SMD2 SMD1 SMD0
Serial mode control
status register (SMCS)
*: Interrupt number
SIE SIR BUSY STOP STRT
—
—
—
—
MODE
BDS SOE SCOE
Interrupt request
#19 (SMCS0)*
#21 (SMCS1)*
#23 (SMCS2)*
55
MB90570 Series
8. I2C Interface
The I2C interface is a serial I/O port supporting Inter IC BUS operating as master/slave devices on I2C bus.
The MB90570/A series contains one channel of an I2C interface, having the following features.
• Master/slave transmission/reception
• Arbitration function
• Clock synchronization function
• Slave address/general call address detection function
• Transmission direction detection function
• Repeated generation function start condition and detection function
• Bus error detection function
(1) Register Configuration
• I2C bus status register (IBSR)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
(IBCR)
000068H
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
BB
RSC
AL
LRB
TRX
AAS
GCA
FBT
00000000B
R
R
R
R
R
R
R
R
• I2C bus control register (IBCR)
Address
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . bit 0
Initial value
000069H
BER
BEIE
SCC
MSS
ACK
GCAA
INTE
INT
(IBSR)
00000000B
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
• I2C bus clock control register (ICCR)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00006AH
(IADR)
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
—
—
EN
CS4
CS3
CS2
CS1
CS0
--0XXXXXB
—
—
R/W
R/W
R/W
R/W
R/W
R/W
bit 12
bit 11
• I2C bus address register (IADR)
Address
bit 15
00006B
—
A6
A5
A4
A3
A2
—
R/W
R/W
R/W
R/W
R/W
H
bit 14
bit 13
bit 10
bit 8
bit 7 . . . . . . . . . . . . bit 0
Initial value
A1
A0
(ICCR)
-XXXXXXXB
R/W
R/W
bit 9
• I2C bus data register (IDAR)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Initial value
00006CH
D7
D6
D5
D4
D3
D2
D1
D0
XXXXXXXXB
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(Disabled)
R/W: Readable and writable
R: Read only
—: Reserved
X: Indeterminate
56
MB90570 Series
(2) Block Diagram
Internal data bus
I2C bus status register
(IBSR)
Start stop condition
generation circuit
General call
Slave
Transmit/receive
Last bit
Transmission
complete flag
Interrupt enable
GC-ACK enable
ACK enable
BB RSC AL LRB TRX AAS GCA FBT
Detection of first byte
Number of
interrupt
request
generated
Master
Start
Error
BER BEIE SCC MSS ACK GCAA INTE INT
Repeat start
I C bus control register
(IBCR)
Bus busy
2
Start stop condition
detection circuit
Interrupt request signal
#36*
SDA line
SCL line
Pin
PA6/SDA
I2C enable
Pin
IDAR register
PA7/SCL
Arbitration lost
detection circuit
Slave address
comparison circuit
IADR register
Clock control block
Sync
Clock
4
divider 1
(1/5 to
1/8)
φ
Count
clock
selector 1
Clock
divider 2
8
Count
clock
selector 2
Shift clock
generation
circuit
I2C enable
—
—
EN CS4 CS3 CS2 CS1 CS0
I2C bus clock control register
(ICCR)
φ:Machine clock frequency
*:Interrupt number
57
MB90570 Series
9. UART0 (SCI), UART1 (SCI)
UART0 (SCI) and UART1 (SCI) are general-purpose serial data communication interfaces for performing synchronous or asynchronous communication (start-stop synchronization system).
• Data buffer: Full-duplex double buffer
• Transfer mode: Clock synchronized (with start and stop bit)
Clock asynchronized (start-stop synchronization system)
• Baud rate: Embedded dedicated baud rate generator
External clock input possible
Internal clock (a clock supplied from 8-bit PPG timer ch1 or 16-bit PPG timer can be used.)
Internal machine clock
Asynchronization 9615 bps/31250 bps/4808 bps/2404 bps/1202 bps
For 6 MHz, 8 MHz, 10 MHz
CLK synchronization 1 Mbps/500 kbps/250 kbps/125 kbps/62.5 kbps
12 MHz and 16 MHz
• Data length: 7 bit to 9 bit selective (without a parity bit)
6 bit to 8 bit selective (with a parity bit)
• Signal format: NRZ (Non Return to Zero) system
• Reception error detection:Framing error
Overrun error
Parity error (multi-processor mode is supported, enabling setup of any baud rate
by an external clock.)
• Interrupt request: Receive interrupt (receive complete, receive error detection)
Transmit interrupt (transmission complete)
Transmit/receive conforms to extended intelligent I/O service (EI2OS)
}
58
MB90570 Series
(1) Register Configuration
• Serial control register 0,1 (SCR0, SCR1)
Address
000021H
000025H
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . . bit 0
PEN
P
SBL
CL
A/D
REC
RXE
TXE
(SMR0, SMR1)
R/W
R/W
R/W
R/W
R/W
W
R/W
R/W
Initial value
00000100 B
• Serial mode register 0, 1 (SMR0, SMR1)
Address
000020H
000024H
bit 15. . . . . . . . . . . . bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
(SCR0, SCR1)
MD1
MD0
CS2
CS1
CS0
RESV
SCKE
SOE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
• Serial status register 0,1 (SSR0, SSR1)
Address
000023H
000027H
bit 15
bit 14
bit 13
bit 12
bit 11
PE
ORE
FRE
RDRF TRDE
R
R
R
R
R
bit 10
bit 9
bit 8
bit 7 . . . . . . . . . . . . . bit 0
—
RIE
TIE
(SIDR0, SIDR1/SODR0,SODR1)
—
R/W
R/W
Initial value
00001 - 00 B
• Serial input data register 0,1 (SIDR0, SIDR1)
Address
000022H
000026H
bit 15. . . . . . . . . . . . bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
(SSR0, SSR1)
D7
D6
D5
D4
D3
D2
D1
D0
R
R
R
R
R
R
R
R
Initial value
XXXXXXXX B
• Serial output data register 0,1 (SODR0, SODR1)
Address
000022H
000026H
bit 15. . . . . . . . . . . . bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
(SSR0, SSR1)
D7
D6
D5
D4
D3
D2
D1
D0
W
W
W
W
W
W
W
W
Initial value
XXXXXXXX B
• Communications prescaler control register 0,1 (CDCR0, CDCR1)
Address
000028H
00002AH
bit 15. . . . . . . . . . . . bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
(Disabled)
MD
—
—
—
DIV3
DIV2
DIV1
DIV0
R/W
—
—
—
R/W
R/W
R/W
R/W
Initial value
0 - - - 1111 B
R/W :Readable and writable
R :Read only
W :Write only
— :Reserved
X :Undefined
RESV: Reserved bit
59
MB90570 Series
(2) Block Diagram
• UART0 (SCI)
Control bus
Dedicated baud
rate generator
8/16-bit PPG
timer 1 (upper)
External clock
Receive
interrupt signal
#39*
Transmit
interrupt signal
#40*
Transmit
clock
Clock
selector
Receive
clock
Receive
control circuit
Transmit
control circuit
Pin
P42/SCK0
Start bit
detection circuit
Transmit start
circuit
Receive bit
counter
Transmit bit
counter
Receive parity
counter
Transmit parity
counter
Pin
P41/SOT0
Shift register for
transmission
Shift register for
reception
Pin
P40/SIN0
Reception
complete
SIDR0
Start transmission
SODR0
Receive condition
decision circuit
To I2C reception
error generation
signal (to CPU)
Internal data bus
SMR0
register
MD1
MD0
CS2
CS1
CS0
SCKE
SOE
*: Interrupt number
60
SCR0
register
PEN
P
SBL
CL
A/D
REC
RXE
TXE
SSR0
register
PE
ORE
FRE
RDRF
TDRE
RIE
TIE
MB90570 Series
• UART1 (SCI)
Control bus
Transmit
clock
Dedicated baud
rate generator
8/16-bit PPG
timer 1 (upper)
Receive
interrupt signal
#37*
Transmit
interrupt signal
#38*
Clock
selector
Receive
clock
Pin
P45/SCK1
Receive
control circuit
Transmit
control circuit
Start bit
detection circuit
Transmit start
circuit
Receive bit
counter
Transmit bit
counter
Receive parity
counter
Transmit parity
counter
Pin
P44/SOT1
Shift register for
transmission
Shift register for
reception
Pin
P43/SIN1
Reception
complete
SIDR1
Start transmission
SODR1
Receive condition
decision circuit
To EI2OS reception
error generation
signal (to CPU)
Internal data bus
SMR1
register
MD1
MD0
CS2
CS1
CS0
SCKE
SOE
SCR1
register
PEN
P
SBL
CL
A/D
REC
RXE
TXE
SSR1
register
PE
ORE
FRE
RDRF
TDRE
RIE
TIE
*: Interrupt number
61
MB90570 Series
10. DTP/External Interrupt Circuit
DTP (Data Transfer Peripheral), which is located between the peripheral circuit outside the device and the
F2MC-16LX CPU, receives an interrupt request or DMA request generated by the external peripheral circuit* for
transmission to the F2MC-16LX CPU. DTP is used to activate the intelligent I/O service or interrupt processing.
As request levels for IRQ2 to IRQ7, two types of “H” and “L” can be selected for the intelligent I/O service. Rising
and falling edges as well as “H” and “L” can be selected for an external interrupt request. For IRQ0 and IRQ1,
a request by a level cannot be entered, but both edges can be entered.
* : The external peripheral circuit is connected outside the MB90570/A series device.
Note : IRQ0 and IRQ1 cannot be used for the intelligent I/O service and return from an interrupt.
(1) Register Configuration
• DTP/interrupt factor register (EIRR)
Address bit 15
000031H
ER7
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
ER6
ER5
ER4
ER3
ER2
ER1
ER0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(ENIR)
Initial value
XXXXXXXX B
• DTP/interrupt enable register (ENIR)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000030H
(EIRR)
EN7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
EN6
EN5
EN4
EN3
EN2
EN1
EN0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
Low order address 000032H
(ELVR upper)
LB3
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
LA3
LB2
LA2
LB1
LA1
LB0
LA0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
• Request level setting register (ELVR)
Address bit 15
High order address 000033H
LB7
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
LA7
LB6
LA6
LB5
LA5
LB4
LA4
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W:Readable and writable
X:Undefined
62
(ELVR lower)
Initial value
00000000 B
Initial value
00000000 B
Pin
PB0/IRQ0
Pin
PB1/IRQ1
Pin
PB2/IRQ2
Pin
PB3/IRQ3
*: Interrupt number
Internal data bus
Pin
PB4/IRQ4
Pin
PB5/IRQ5
Pin
PA0/AIN0/IRQ6
Pin
PA3/AIN1/IRQ7
Level edge
selector 6
Level edge
selector 7
2
EN7
ER7
LB7
EN6
ER6
LA7
EN5
ER5
2
LB6
EN4
ER4
LA6
2
LA5
EN3
ER3
EN2
ER2
Level edge
selector 4
EN1
ER1
LB4
Level edge
selector 5
LB5
Request level setting register (ELVR)
2
LB3
2
LA3
LA2
Level edge
selector 2
Level edge
selector 3
LB2
2
LB1
Interrupt request signal
#35*
#33*
#27*
#25*
#24*
#13*
EN0 DTP/interrupt enable register (ENIR)
LB0
Level edge
selector 0
Level edge
selector 1
LA0
DTP/external interrupt
input detection circuit
2
LA1
ER0 DTP/interrupt factor register (EIRR)
LA4
2
MB90570 Series
(2) Block Diagram
63
MB90570 Series
11. Delayed Interrupt Generation Module
The delayed interrupt generation module generates interrupts for switching tasks for development on a real-time
operating system (REALOS series). The module can be used to generate softwarewise generates hardware
interrupt requests to the CPU and cancel the interrupts.
This module does not conform to the extended intelligent I/O service (EI2OS).
(1) Register Configuration
• Delayed interrupt factor generation/cancellation register (DIRR)
Address
00009FH
bit 8 bit 7 . . . . . . . . . . . . bit 0
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
—
—
—
—
—
—
—
R0
—
—
—
—
—
—
—
R/W
(PACSR)
Initial value
- - - - - - -0B
Note: Upon a reset, an interrupt is canceled.
R/W:Readable and writable
—:Reserved
The DIRR is the register used to control delay interrupt request generation/cancellation. Programming this
register with “1” generates a delay interrupt request. Programming this register with “0” cancels a delay interrupt
request. Upon a reset, an interrupt is canceled. The reserved bit area can be programmed with either “0” or “1”.
For future extension, however, it is recommended that bit set and clear instructions be used to access this register.
(2) Block Diagram
Internal data bus
—
—
—
—
—
Delayed interrupt factor generation/
cancellation register (DIRR)
*: Interrupt number
64
—
—
R0
S factor
R latch
Interrupt request signal
#42*
MB90570 Series
12. 8/10-bit A/D Converter
The 8/10-bit A/D converter has a function of converting analog voltage input to the analog input pins (input
voltage) to digital values (A/D conversion) and has the following features.
• Minimum conversion time: 26.3 µs (at machine clock of 16 MHz, including sampling time)
• Minimum sampling time: 4 µs/256 µs (at machine clock of 16 MHz)
• Compare time: 176/352 machine cycles per channel (176 machine cycles are used for a machine clock below
8 MHz.)
• Conversion method: RC successive approximation method with a sample and hold circuit.
• 8-bit or 10-bit resolution
• Analog input pins: Selectable from eight channels by software
Single conversion mode: Selects and converts one channel.
Scan conversion mode:Converts two or more successive channels. Up to eight channels can be programmed.
Continuous conversion mode: Repeatedly converts specified channels.
Stop conversion mode:Stops conversion after completing a conversion for one channel and wait for the next
activation (conversion can be started synchronously.)
• Interrupt requests can be generated and the extended intelligent I/O service (EI2OS) can be started after the
end of A/D conversion. Furthermore, A/D conversion result data can be transferred to the memory, enabling
efficient continuous processing.
• When interrupts are enabled, there is no loss of data even in continuous operations because the conversion
data protection function is in effect.
• Starting factors for conversion: Selected from software activation, and external trigger (falling edge).
65
MB90570 Series
(1) Register Configuration
• A/D control status register upper digits (ADCS2)
Address
000037H
bit 8 bit 7 . . . . . . . . . . . . bit 0
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
BUSY
INT
INTE
PAUS
STS1
STS0
STRT RESV
R/W
R/W
R/W
R/W
R/W
R/W
W
(ADCS1)
Initial value
00000000 B
R/W
• A/D control status register lower digits (ADCS1)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000036H
(ADCS2)
MD1
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
MD0
ANS2
ANS1
ANS0
ANE2
ANE1
ANE0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
00000000 B
• A/D data register upper digits (ADCR2)
Address
000039H
bit 8 bit 7 . . . . . . . . . . . . bit 0
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
DSEL
ST1
ST0
CT1
XCT0
—
D9
D8
W
W
W
W
W
—
—
—
(ADCR1)
Initial value
0 0 0 0 1 - XX B
• A/D data register lower digits (ADCR1)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000038H
(ADCR2)
D7
R
R/W :Readable and writable
R :Read only
W :Write only
— :Reserved
X :Undefined
RESV: Reserved bit
66
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
D6
D5
D4
D3
D2
D1
D0
R
R
R
R
R
R
R
Initial value
XXXXXXXX B
MB90570 Series
(2) Block Diagram
A/D control status
register (ADCS)
Interrupt request #11*
BUSY INT INTE PAUS STS1 STS0 STRT
DA MD1 MD0 ANS2 ANS1 ANS0 ANE2 ANE1 ANE0
6
2
Clock selector
Decoder
Internal data bus
PB6/ADTG
TO
φ
Comparator
P87/AN7
P86/AN6
P85/AN5
P84/AN4
P83/AN3
P82/AN2
P81/AN1
P80/AN0
Sample hold
circuit
Control circuit
Analog
channel
selector
A/D data register RESV
ST1 ST0 CT1 CT0
(ADCR)
AVRH, AVRL
AVCC
AVSS
—
D9
D8
8-bit D/A converter
D7
D6
D5
D4
D3
D2
D1
D0
φ:Machine clock frequency
TO:8/16-bit PPG timer channel 1 output
*:Interrupt number
67
MB90570 Series
13. 8-bit D/A Converter
The 8-bit D/A converter, which is based on the R-2R system, supports 8-bit resolution mode. It contains two
channels each of which can be controlled in terms of output by the D/A control register.
(1) Register Configuration
• D/A converter data register ch.0 (DADR0)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00003AH
(DADR1)
DA07
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
DA06
DA05
DA04
DA03
DA02
DA01
DA00
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Initial value
XXXXXXXX B
• D/A converter data register ch.1 (DADR1)
Address
00003BH
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
DA17
DA16
DA15
DA14
DA13
DA12
DA11
DA10
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
(DADR0)
Initial value
XXXXXXXX B
• D/A control register 0 (DACR0)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
00003CH
(DACR1)
—
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
—
—
—
—
—
—
DAE0
—
—
—
—
—
—
—
R/W
Initial value
- - - - - - -0B
• D/A control register 1 (DACR1)
Address
00003DH
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
—
—
—
—
—
—
—
DAE1
—
—
—
—
—
—
—
R/W
R/W:Readable and writable
—:Reserved
X:Undefined
68
bit 8 bit 7 . . . . . . . . . . . . bit 0
bit 15
(DACR0)
Initial value
- - - - - - -0B
MB90570 Series
(2) Block Diagram
Internal data bus
D/A converter data register ch.1 (DADR1)
D/A converter data register ch.0 (DADR0)
DA17 DA16 DA15 DA14 DA13 DA12 DA11 DA10
DA07 DA06 DA05 DA04 DA03 DA02 DA01 DA00
D/A converter 1
D/A converter 0
DVRH
DVRL
DA07
DA17
Pin
2R
R
DA16
2R
DA15
2R
DA14
2R
DA13
2R
DA12
2R
DA11
2R
DA10
2R
P74/DA1
Pin
2R
DA06
2R
R
DA05
R
DA04
R
DA03
R
DA02
R
DA01
R
DA00
2R
2R
2R
2R
2R
2R
2R
DVSS
—
—
R
R
R
R
R
R
2R
Standby control
D/A control register 1 (DACR1)
—
R
DVSS
Standby control
—
P73/DA0
—
D/A control register 0 (DACR0)
—
— DAE1
—
—
—
—
—
—
— DAE0
Internal data bus
69
MB90570 Series
14. Clock Timer
The clock timer control register (WTC) controls operation of the clock timer, and time for an interval interrupt.
(1) Register Configuration
• Clock timer control register (WTC)
. . . . . . . . . . . . bit 8 bit 7
Address bit 15
0000AAH
(Disabled)
WDCS
bit 6
bit 5
SCE
WTIE WTOF
R/W
R
R/W
bit 4
R/W
bit 3
WTR
R/W
bit 2
bit 1
bit 0
WTC2 WTC1 WTC0
R
R/W
Initial value
1X0 0 0 0 0 0 B
R/W
R/W:Readable and writable
R:Read only
X:Undefined
(2) Block Diagram
To watchdog timer
Clock counter
LCLK
× 21 × 22 × 23 × 24 × 25 × 26 × 27 × 28 × 29 × 210 × 211 × 212 × 213 × 214 × 215
OF
OF
OF
OF
OF
OF
OF
Power-on reset
Shift to a hardware standby
Counter
clear circuit
To sub-clock oscillation stabilization
time controller
Shift to stop mode
Interval
timer selector
Clock timer interrupt request
#22*
WDCS SCE
WTIE WTOF WTR WTC2 WTC1 WTC0
Clock timer control register (WTC)
*:Interrupt number
OF:Overflow
LCLK:Oscillation sub-clock frequency
70
MB90570 Series
15. Chip Select Output
This module generates a chip select signal for facilitating a memory and I/O unit, and is provided with eight chip
select output pins. When access to an address is detected with a hardware-set area set for each pin register, a
select signal is output from the pin.
(1) Register Configuration
• Chip selection control register 1, 3, 5, 7 (CSCR1, CSCR3, CSCR5, CSCR7)
Address
CSCR1: 000081H
CSCR3: 000083H
CSCR5: 000085H
CSCR7: 000087H
bit 8 bit 7 . . . . . . . . . . . . bit 0
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
—
—
—
—
ACTL
OPEL
CSA1
CSA0
—
—
—
—
R/W
R/W
R/W
R/W
(CSCR0, CSCR2, CSCR4, CSCR6)
Initial value
- - - - 0000 B
• Chip selection control register 0, 2, 4, 6 (CSCR0, CSCR2, CSCR4, CSCR6)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
CSCR0: 000080H
CSCR2: 000082H (CSCR1, CSCR3, CSCR5, CSCR7) —
CSCR4: 000084H
—
CSCR6: 000086H
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
—
—
—
ACTL
OPEL
CSA1
CSA0
—
—
—
R/W
R/W
R/W
R/W
Initial value
- - - - 0000 B
R/W:Readable and writable
—:Reserved
71
MB90570 Series
(2) Block Diagram
From address (CPU)
A23
A22
⋅⋅⋅⋅⋅
A17
A16
A15
Address decoder
A14
⋅⋅⋅⋅⋅
A01
A00
Address decoder
Decode signal
Program area
Decode
P90/CS0
(Program ROM area application)
2
Select and set
Selector
Chip selection control register 0 (CSCR0)
Select and set
Chip selection control register 1 (CSCR1)
Selector
P91/CS1
Select and set
Chip selection control register 2 (CSCR2)
Selector
P92/CS2
Select and set
Chip selection control register 3 (CSCR3)
Selector
P93/CS3
Select and set
Chip selection control register 4 (CSCR4)
Selector
P94/CS4
Select and set
Selector
Chip selection control register 5 (CSCR5)
P95/CS5
Select and set
Chip selection control register 6 (CSCR6)
Selector
P96/CS6
Chip selection control register 7 (CSCR7)
Select and set
Selector
P97/CS7
72
MB90570 Series
(3) Decode Address Spaces
CSA
Pin
Decode space
name
1
0
CS0
CS1
CS2
CS3
CS4
CS5
CS6
CS7
Number of
area bytes
0
0
F00000H to FFFFFFH
1 Mbyte
0
1
F80000H to FFFFFFH
512 kbyte
1
0
FE0000H to FFFFFFH
128 kbyte
1
1
0
0
E00000H to EFFFFFH
1 Mbyte
0
1
F00000H to F7FFFFH
512 kbyte
1
0
FC0000H to FDFFFFH
128 kbyte
1
1
68FF80H to 68FFFFH
128 byte
0
0
003000H to 003FFFH
4 kbyte
0
1
FA0000H to FBFFFFH
128 kbyte
1
0
68FF80H to 68FFFFH
128 byte
1
1
68FF00H to 68FF7FH
128 byte
0
0
F80000H to F9FFFFH
128 kbyte
0
1
68FF00H to 68FF7FH
128 byte
1
0
68FE80H to 68FEFFH
128 byte
1
1
0
0
002800H to 002FFFH
2 kbyte
0
1
68FE80H to 68FEFFH
128 byte
1
0
—
Disabled
1
1
—
Disabled
0
0
0
1
—
Disabled
1
0
—
Disabled
1
1
—
Disabled
0
0
0
1
—
Disabled
1
0
—
Disabled
1
1
—
Disabled
—
—
—
Disabled
—
—
68FF80H to 68FFFFH
68FF00H to 68FF7FH
Remarks
Becomes active when the program ROM
area or the program vector is fetched.
Disabled
Adapted to the data ROM and RAM areas,
and external circuit connection applications.
Adapted to the data ROM and RAM areas,
and external circuit connection applications.
Adapted to the data ROM and RAM areas,
and external circuit connection applications.
Disabled
Adapted to the data ROM and RAM areas,
and external circuit connection applications.
128 byte
Adapted to the data ROM and RAM areas,
and external circuit connection applications.
128 byte
Adapted to the data ROM and RAM areas,
and external circuit connection applications.
Disabled
73
MB90570 Series
16. Communications Prescaler Register
This register controls machine clock division.
Output from the communications prescaler register is used for UART0 (SCI), UART1 (SCI), and extended I/O
serial interface.
The communications prescaler register is so designed that a constant baud rate may be acquired for various
machine clocks.
(1) Register Configuration
• Communications prescaler control register 0,1 (CDCR0, CDCR1)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
000028H
00002AH
(Disabled)
R/W:Readable and writable
—:Reserved
74
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
MD
—
—
—
DIV3
DIV2
DIV1
DIV0
R/W
—
—
—
R/W
R/W
R/W
R/W
Initial value
0 - - - 1111 B
MB90570 Series
17. Address Match Detection Function
When the address is equal to a value set in the address detection register, the instruction code loaded into the
CPU is replaced forcibly with the INT9 instruction code (01H). As a result, when the CPU executes a set
instruction, the INT9 instruction is executed. Processing by the INT#9 interrupt routine allows the program
patching function to be implemented.
Two address detection registers are supported. An interrupt enable bit is prepared for each register. If the value
set in the address detection register matches an address and if the interrupt enable bit is set at “1”, the instruction
code loaded into the CPU is replaced forcibly with the INT9 instruction code.
(1) Register Configuration
• Program address detection register 0 to 2 (PADR0)
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
PADR0 (Low order address): 001FF0H
Address
PADR0 (Middle order address): 001FF1H
Address
PADR0 (High order address): 001FF2H
Initial value
XXXXXXXX B
Initial value
XXXXXXXX B
Initial value
XXXXXXXX B
• Program address detection register 3 to 5 (PADR1)
Address
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
bit 3
bit 2
bit 1
bit 0
AD0E
RESV
R/W
R/W
PADR1 (Low order address): 001FF3H
Address
PADR1 (Middle order address): 001FF4H
Address
PADR1 (High order address): 001FF5H
Initial value
XXXXXXXX B
Initial value
XXXXXXXX B
Initial value
XXXXXXXX B
• Program address detection control status register (PACSR)
Address
bit 7
00009EH
RESV
R/W
bit 6
bit 5
RESV RESV
R/W
R/W
bit 4
RESV AD1E RESV
R/W
R/W
R/W
Initial value
00000000 B
R/W :Readable and writable
X :Undefined
RESV:Reserved bit
75
MB90570 Series
Internal data bus
Address latch
76
Address detection
register
Enable bit
Compare
(2) Block Diagram
INT9
instruction
F2MC-16LX
CPU core
MB90570 Series
18. ROM Mirroring Function Selection Module
The ROM mirroring function selection module can select what the FF bank allocated the ROM sees through the
00 bank according to register settings.
(1) Register Configuration
• ROM mirroring function selection register (ROMM)
Address
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
00006FH
—
—
—
—
—
—
—
MI
—
—
—
—
—
—
—
W
(Disabled)
Initial value
- - - - - - -1B
W:Write only
—:Reserved
Note : Do not access this register during operation at addresses 004000H to 00FFFFH.
(2) Block Diagram
Internal data bus
ROM mirroring function selection
register (ROMM)
Address area
Address
FF bank
00 bank
Data
ROM
77
MB90570 Series
19. Low-power Consumption (Standby) Mode
The F2MC-16LX has the following CPU operating mode configured by selection of an operating clock and clock
operation control.
• Clock mode
PLL clock mode: A mode in which the CPU and peripheral equipment are driven by PLL-multiplied oscillation
clock (HCLK).
Main clock mode:A mode in which the CPU and peripheral equipment are driven by divided-by-2 of the oscil
lation clock (HCLK).
The PLL multiplication circuits stops in the main clock mode.
• CPU intermittent operation mode
The CPU intermittent operation mode is a mode for reducing power consumption by operating the CPU
intermittently while external bus and peripheral functions are operated at a high-speed.
• Hardware standby mode
The hardware standby mode is a mode for reducing power consumption by stopping clock supply to the CPU
by the low-power consumption control circuit, stopping clock supplies to the CPU and peripheral functions
(timebase timer mode), and stopping oscillation clock (stop mode, hardware standby mode). Of these modes,
modes other than the PLL clock mode are power consumption modes.
(1) Register Configuration
• Clock select register (CKSCR)
Address
bit 15
bit 14
bit 13
bit 12
bit 11
bit 10
bit 9
bit 8 bit 7 . . . . . . . . . . . . bit 0
0000A1H
SCM
MCM
WS1
WS0
SCS
MCS
CS1
CS0
R
R
R/W
R/W
R/W
R/W
R/W
R/W
(LPMCR)
Initial value
11111100 B
• Low-power consumption mode control register (LPMCR)
Address bit 15 . . . . . . . . . . . . bit 8 bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
0000A0H
STP
SLP
SPL
RST
TMD
CG1
CG0
SSR
W
W
R/W
W
R/W
W
R/W
R/W
(CKSCR)
R/W:Readable and writable
R:Read only
W:Write only
78
Initial value
00011000 B
MB90570 Series
(2) Block Diagram
Standby control circuit
Low-power consumption mode control register
(LPMCR)
STP SLP SPL RST TMD CG1 CG0 SSR
2
CPU intermittent
operation cycle
selector
CPU clock
control circuit
CPU operation
clock
Clock mode
Sleep signal
Stop signal
Peripheral clock
control circuit
Hardware
standby
S
Q
S
R
Reset
Interrupt
Q
R
S
Q
S
R
Peripheral function
operation clock
Machine clock
Q
R
Clock selector
Oscillation
stabilization
time selector
2
2
PLL multiplication
circuit
SCM MCM WS1 WS0 SCS MCS CS1 CS0
Clock select register (CKSCR)
X0
Pin
X1
Pin
Oscillation
clock
1/2
Clock oscillator
Main
clock
1/2048
1/4
1/4
1/8
Timebase timer
To watchdog timer
X0A Pin
X1A Pin
Oscillation
sub-clock
Sub-clock oscillator
1/1024
1/8
1/2
1/2
Clock timer
S: Set
R: Reset
Q: Output
79
MB90570 Series
■ ELECTRICAL CHARACTERISTICS
1. Absolute Maximum Ratings
(AVSS = VSS = 0.0 V)
Parameter
Symbol
Value
Unit
Remarks
Min
Max
VCC
VSS – 0.3
VSS + 6.0
V
AVCC
VSS – 0.3
VSS + 6.0
V
*1
AVRH,
AVRL
VSS – 0.3
VSS + 6.0
V
*1
DVRH
VSS – 0.3
VSS + 6.0
V
*1
Input voltage
VI
VSS – 0.3
VSS + 6.0
V
*2
Output voltage
VO
VSS – 0.3
VSS + 6.0
V
*2
“L” level maximum output current
IOL

15
mA
*3
“L” level average output current
IOLAV

4
mA
*4
“L” level total maximum output current
ΣIOL

100
mA
ΣIOLAV

50
mA
*5
IOH

–15
mA
*3
“H” level average output current
IOHAV

–4
mA
*4
“H” level total maximum output current
ΣIOH

–100
mA
ΣIOHAV

–50
mA
*5

300
mW
MB90573/4
MB90V570/A

500
mW
MB90574C

800
mW
MB90F574/A
TA
–40
+85
°C
Tstg
–55
+150
°C
Power supply voltage
“L” level total average output current
“H” level maximum output current
“H” level total average output current
Power consumption
PD
Operating temperature
Storage temperature
*1 : Care must be taken that AVCC, AVRH, AVRL, and DVRH do not exceed VCC. Also, care must be taken that
AVRH and AVRL do not exceed AVCC, and AVRL does not exceed AVRH.
*2 : VI and VO shall never exceed VCC + 0.3 V.
*3 : The maximum output current is a peak value for a corresponding pin.
*4 : Average output current is an average current value observed for a 100 ms period for a corresponding pin.
*5 : Total average current is an average current value observed for a 100 ms period for all corresponding pins.
Note : Average output current = operating × operating efficiency
WARNING: Semiconductor devices can be permanently damaged by application of stress (voltage, current,
temperature, etc.) in excess of absolute maximum ratings. Do not exceed these ratings.
80
MB90570 Series
2. Recommended Operating Conditions
(AVSS = VSS = 0.0 V)
Parameter
Symbol
Value
Unit
Remarks
Min
Max
VCC
3.0
5.5
V
Normal operation (MB90574/C)
VCC
4.5
5.5
V
Normal operation (MB90F574/A)
VCC
3.0
5.5
V
Retains status at the time of operation
stop
Smoothing capacitor
CS
0.1
1.0
µF
*
Operating temperature
TA
–40
+85
°C
Power supply voltage
* : Use a ceramic capacitor or a capacitor with equivalent frequency characteristics. The smoothing capacitor to be
connected to the VCC pin must have a capacitance value higher than CS.
WARNING: The recommended operating conditions are required in order to ensure the normal operation of the
semiconductor device. All of the device’s electrical characteristics are warranted when the device is
operated within these ranges.
Always use semiconductor devices within their recommended operating condition ranges. Operation
outside these ranges may adversely affect reliability and could result in device failure.
No warranty is made with respect to uses, operating conditions, or combinations not represented on
the data sheet. Users considering application outside the listed conditions are advised to contact their
FUJITSU representatives beforehand.
• C pin connection circuit
C
CS
81
MB90570 Series
3. DC Characteristics
Parameter
“H” level input
voltage
Symbol
VIHS
VIHM
“L” level input
voltage
VILS
Pin name
(AVCC = VCC = 5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Condition
Unit
Remarks
Min
Typ
Max
CMOS
hysteresis
input pin
0.8 VCC
—
VCC + 0.3
V
—
VCC + 0.3
V
—
0.2 VCC
V
VSS – 0.3
—
VSS + 0.3
V
VCC – 0.5
—
—
V
—
—
0.4
V
—
0.1
5
µA
–5
—
5
µA
VCC = 3.0 V to 5.5 V
MD pin input (MB90573)
VCC – 0.3
(MB90574)
CMOS
VCC = 4.5 V to 5.5 V
hysteresis
VSS – 0.3
(MB90F574)
input pin
VILM
MD pin input
“H” level output
voltage
VOH
Other than
PA6 and
PA7
VCC = 4.5 V
IOH = –2.0 mA
“L” level output
voltage
VOL
All output
pins
VCC = 4.5 V
IOL = 2.0 mA
Open-drain
output leakage
current
Ileak
PA6, PA7
Input leakage
current
IIL
Other than
PA6 and
PA7
Pull-up
resistance
RUP
P00 to P07,
P10 to P17,
P60 to P67,
RST, MD0,
MD1
—
15
30
100
kΩ
Pull-down
resistance
RDOWN
MD0 to MD2
—
15
30
100
kΩ
—
30
40
mA MB90574
—
85
130
mA MB90F574/A
—
50
80
mA MB90574C
—
35
45
mA MB90574
—
90
140
mA MB90F574/A
—
55
85
mA MB90574C
—
40
50
mA MB90574
—
95
145
mA MB90F574/A
—
65
85
mA MB90574C
Power supply
current
ICC
VCC
ICC
VCC
ICC
VCC
ICC
VCC
ICC
VCC
ICC
VCC
ICC
VCC
ICC
VCC
ICC
VCC
—
VCC = 5.5 V
VSS < VI < VCC
Internal operation
at 16 MHz
VCC at 5.0 V
Normal operation
Internal operation
at 16 MHz
VCC at 5.0 V
A/D converter
operation
Internal operation
at 16 MHz
VCC at 5.0 V
D/A converter
operation
(Continued)
82
MB90570 Series
(Continued)
Parameter
Power supply
current
Input
capacitance
Symbol
Pin name
ICC
VCC
ICCS
VCC
ICCS
VCC
ICCS
VCC
ICCL
VCC
ICCL
VCC
ICCL
VCC
ICCLS
VCC
ICCLS
VCC
ICCLS
VCC
ICCT
VCC
ICCT
VCC
ICCT
VCC
ICCH
VCC
ICCH
VCC
CIN
Other than
AVCC,
AVSS, VCC,
VSS
(AVCC = VCC = 5.0 V ± 10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Condition
Unit
Remarks
Min
Typ
Max
When data written
in flash mode
programming of
erasing
Internal operation
at 16 MHz
VCC = 5.0 V
In sleep mode
Internal operation
at 8 kHz
VCC = 5.0 V
TA = +25°C
Subsystem
operation
Internal operation
at 8 kHz
VCC = 5.0 V
TA = +25°C
In subsleep mode
Internal operation
at 8 kHz
VCC = 5.0 V
TA = +25°C
In clock mode
TA = +25°C
In stop mode
—
—
95
140
mA MB90F574/A
—
7
12
mA MB90574
—
5
10
mA MB90F574/A
—
15
20
mA MB90574C
—
0.1
1.0
mA MB90574
—
4
7
mA MB90F574/A
—
0.03
1
mA MB90574C
—
30
50
µA
—
0.1
1
mA MB90F574/A
—
10
50
µA
MB90574C
—
15
30
µA
MB90574
—
30
50
µA
MB90F574/A
—
1.0
30
µA
MB90574C
—
5
20
µA
MB90574
—
0.1
10
µA
MB90F574/A
MB90574C
—
10
80
pF
MB90574
83
MB90570 Series
4. AC Characteristics
(1) Reset, Hardware Standby Input Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin
Symbol
Condition
Unit
Remarks
Parameter
name
Min
Max
Reset input time
RST
tRSTL
Hardware standby input time
tHSTL
—
HST
4 tCP
—
ns
Under normal
operation
Oscillation time of
oscillator * + 4 tCP
—
ms
In stop mode
4 tCP
—
ns
* : Oscillation time of oscillator is time that the amplitude reached the 90 %.
In the crystal oscillator, the oscillation time is between several ms to tens ms. In FAR/ceramic oscillator, the
oscillation time is between hundreds of µs to several ms. In the external clock, the oscillation time is 0 ms.
Note : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
Under Normal operation
tRSTL, tHSTL
RST
HST
0.2 VCC
In Stop Mode
0.2 VCC
tRSTL
RST
0.2 VCC
0.2 VCC
90 % of
amplitude
X0
Internal operation clock
4 tCP
Oscillation time
of oscillator
Oscillation setting time
Instruction execution
Internal reset
• Measurement conditions for AC characteristics
Pin
CL
CL is a load capacitance connected to a pin under test.
Capacitors of CL = 30 pF must be connected to CLK and ALE pins, while CL of 80 pF must
be connected to address data bus (AD15 to AD00), RD, WRL, and WRH pins.
84
MB90570 Series
(2) Specification for Power-on Reset
Parameter
Symbol Pin name
Power supply rising time
tR
VCC
Power supply cut-off time
tOFF
VCC
Condition
—
(AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Unit
Remarks
Min
Max
0.05
30
ms
*
4
—
ms
Due to repeated
operations
* : VCC must be kept lower than 0.2 V before power-on.
Note : • The above ratings are values for causing a power-on reset.
• There are internal registers which can be initialized only by a power-on reset.
Apply power according to this rating to ensure initialization of the registers.
tR
VCC
2.7 V
0.2 V
0.2 V
0.2 V
tOFF
Sudden changes in the power supply voltage may cause a power-on reset.
To change the power supply voltage while the device is in operation, it is recommended to raise the voltage
smoothly to suppress fluctuations as shown below.
In this case, change the supply voltage with the PLL clock not used. If the voltage drop is 1 V/s or fewer per second, however, you can use the PLL clock.
VCC
3.0 V
VSS
It is recommended to keep the rising
speed of the supply voltage at 50 mV/ms
or slower.
85
MB90570 Series
(3) Clock Timings
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
CondiSymbol Pin name
Unit
Remarks
tion
Min
Typ
Max
Parameter
Clock frequency
Clock cycle time
Input clock pulse width
Input clock rising/falling time
Internal operating clock frequency
Internal operating clock cycle
time
Frequency fluctuation rate
locked
FC
X0, X1
3
—
16
MHz
FCL
X0A, X1A
—
32.768
—
kHz
tHCYL
X0, X1
62.5
—
333
ns
tLCYL
X0A, X1A
—
30.5
—
µs
PWH,
PWL
X0
10
—
—
ns
PWLH,
PWLL
X0A
—
15.2
—
µs
—
—
5
ns
External clock
operation
tCR,
tCF
X0, X0A
—
Recommend
duty ratio of
30% to 70%
fCP
—
1.5
—
16
MHz
Main clock operation
fLCP
—
—
8.192
—
kHz
Subclock operation
tCP
—
62.5
—
333
ns
External clock
operation
tLCP
—
—
122.1
—
µs
Subclock operation
∆f
—
—
—
5
%
*
* : The frequency fluctuation rate is the maximum deviation rate of the preset center frequency when the multiplied
PLL signal is locked.
+
+α
∆f = | α |
fO
× 100 (%)
Center frequency
fO
–α
–
The PLL frequency deviation changes periodically from the preset frequency “(about CLK × (1CYC to 50 CYC)”,
thus minimizing the chance of worst values to be repeated (errors are minimal and negligible for pulses with
long intervals).
86
MB90570 Series
• X0, X1 clock timing
tHCYL
0.8 VCC
0.8 VCC
0.8 VCC
0.2 VCC
X0
PWH
0.2 VCC
PWL
tCF
tCR
• X0A, X1A clock timing
tLCYL
0.8 VCC
0.8 VCC
0.8 VCC
0.2 VCC
X0A
PWLH
0.2 VCC
PWLL
tCF
tCR
• PLL operation guarantee range
Relationship between internal operating clock
frequency and power supply voltage
Operation guarantee range (MB90F574/A)
(V)
Power supply voltage VCC
Operation guarantee range MB90574C
5.5
4.5
PLL operation
guarantee range
Operation guarantee range
MB90V570/A
3.3
3.0
1.5
(MHz)
3
8
12
Internal clock fCP
16
(MHz)
Operation guarantee range
MB90573/4
Relationship between oscillating frequency, internal
operating clock frequency, and power supply voltage
Multipliedby-4
16
MultipliedMultiplied-by-2
by-3
Multiplied-by-1
Internal clock fCP
12
9
8
Not multiplied
6
4
3
2
1.5
3
4
6
8
12
16
(MHz)
Oscillation clock FC
87
MB90570 Series
The AC ratings are measured for the following measurement reference voltages.
• Input signal waveform
• Output signal waveform
Hystheresis input pin
Hystheresis input pin
0.8 VCC
2.4 VCC
0.2 VCC
0.8 VCC
Pins other than hystheresis input/MD input
0.7 VCC
0.3 VCC
(4) Recommended Resonator Manufacturers
•Sample application of ceramic resonator
X0
X1
R
*
C1
C2
• Mask ROM product (MB90574)
Resonator
Resonator
manufacturer*
Murata Mfg. Co., Ltd.
TDK Corporation
Frequency (MHz)
C1 (pF)
C1 (pF)
R
CSA2.00MG040
2.00
100
100
No required
CSA4.00MG040
4.00
100
100
No required
CSA8.00MTZ
8.00
30
30
No required
CSA16.00MXZ040
16.00
15
15
No required
CSA32.00MXZ040
32.00
5
5
No required
CCR3.52MC3 to
CCR6.96MC3
3.52 to 6.96
Built-in
Built-in
No required
CCR7.0MC5 to
CCR12.0MC5
7.00 to 12.00
Built-in
Built-in
No required
CCR20.0MSC6 to
CCR32.0MSC6
20.00 to 32.00
Built-in
Built-in
No required
(Continued)
88
MB90570 Series
(Continued)
• Flash product (MB90F574)
Resonator
Resonator
manufacturer*
Murata Mfg. Co., Ltd.
TDK Corporation
Frequency (MHz)
C1 (pF)
C2 (pF)
R
CSA2.00MG040
2.00
100
100
No required
CSA4.00MG040
4.00
100
100
No required
CSA8.00MTZ
8.00
30
30
No required
CSA16.00MXZ040
16.00
15
15
No required
CSA32.00MXZ040
32.00
5
5
No required
CCR3.52MC3 to
CCR6.96MC3
3.52 to 6.96
Built-in
Built-in
No required
CCR7.0MC5 to
CCR12.0MC5
7.00 to 12.00
Built-in
Built-in
No required
CCR20.0MSC6 to
CCR32.0MSC6
20.00 to 32.00
Built-in
Built-in
No required
Inquiry: Murata Mfg. Co., Ltd.
•Murata Electronics North America, Inc.: TEL 1-404-436-1300
•Murata Europe Management GmbH: TEL 49-911-66870
•Murata Electronics Singapore (Pte.): TEL 65-758-4233
TDK Corporation
•TDK Corporation of America
Chicago Regional Office: TEL 1-708-803-6100
•TDK Electronics Europe GmbH
Components Division: TEL 49-2102-9450
•TDK Singapore (PTE) Ltd.: TEL 65-273-5022
•TDK Hongkong Co., Ltd.: TEL: 852-736-2238
•Korea Branch, TDK Corporation: TEL 82-2-554-6636
(5) Clock Output Timing
Parameter
Symbol
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
Cycle time
tCYC
CLK
CLK ↑ → CLK ↓
tCHCL
CLK
—
62.5
—
ns
20
—
ns
tCYC
tCHCL
2.4 V
CLK
2.4 V
0.8 V
89
MB90570 Series
(6) Bus Read Timing
Parameter
Symbol
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
ALE pulse width
tLHLL
ALE
1 tCP*/2 – 20
—
ns
Effective address →
ALE ↓ time
tAVLL
ALE,
A23 to A16,
AD15 to AD00
1 tCP*/2 – 20
—
ns
ALE ↓ → address
effective time
tLLAX
ALE,
AD15 to AD00
1 tCP*/2 – 15
—
ns
Effective address →
RD ↓ time
tAVRL
RD,
A23 to A16,
AD15 to AD00
1 tCP* – 15
—
ns
Effective address →
valid data input
tAVDV
A23 to A16,
AD15 to AD00
—
5 tCP*/2 – 60
ns
RD pulse width
tRLRH
RD
3 tCP*/2 – 20
—
ns
—
3 tCP*/2 – 60
ns
0
—
ns
—
RD ↓ → valid data input
tRLDV
RD,
AD15 to AD00
RD ↑ → data hold time
tRHDX
RD,
AD15 to AD00
RD ↑ → ALE ↑ time
tRHLH
ALE, RD
1 tCP*/2 – 15
—
ns
RD ↑ → address
effective time
tRHAX
ALE,
A23 to A16
1 tCP*/2 – 10
—
ns
Effective address →
CLK ↑ time
tAVCH
CLK,
A23 to A16,
AD15 to AD00
1 tCP*/2 – 20
—
ns
RD ↓ → CLK ↑ time
tRLCH
CLK, RD
1 tCP*/2 – 20
—
ns
ALE ↓ → RD ↓ time
tALRL
ALE, RD
1 tCP*/2 – 15
—
ns
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
90
MB90570 Series
tAVCH
tRLCH
2.4 V
2.4 V
CLK
tRHLH
2.4 V
0.8 V
2.4 V
tLHLL
tAVLL
ALE
2.4 V
tLLAX
tRLRH
RD
2.4 V
0.8 V
tAVRL
tRHAX
tRLDV
2.4 V
0.8 V
AD23 to AD16
2.4 V
0.8 V
tAVDV
AD15 to AD00
2.4 V
0.8 V
Address
2.4 V
0.8 V
0.8 VCC
0.2 VCC
Read data
tRHDX
0.8 VCC
0.2 VCC
91
MB90570 Series
(7) Bus Write Timing
Parameter
Symbol
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
Effective address →
WR ↓ time
tAVWL
WRL, WRH,
A23 to A16,
AD15 to AD00
WR pulse width
tWLWH
Write data → WR ↑ time
1 tCP – 15
—
ns
WRL, WRH
3 tCP*/2 – 20
—
ns
tDVWH
WRL, WRH,
AD15 to AD00
3 tCP*/2 – 20
—
ns
WR ↑ → data hold time
tWHDX
WRL, WRH,
AD15 to AD00
20
—
ns
WR ↑ → address
effective time
tWHAX
WRL, WRH,
A23 to A16
1 tCP*/2 – 10
—
ns
WR ↑ → ALE ↑ time
tWHLH
ALE, WRL
1 tCP*/2 – 15
—
ns
WR ↓ → CLK ↑ time
tWLCH
CLK, WRH
1 tCP*/2 – 20
—
ns
—
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
tWLCH
2.4 V
CLK
tWHLH
2.4 V
ALE
tAVWL
tWLWH
WRL, WRH
2.4 V
0.8 V
tWHAX
A23 to A16
2.4 V
2.4 V
0.8 V
0.8 V
tDVWH
AD15 to AD00
2.4 V
0.8 V
92
Address
2.4 V
0.8 V
tWHDX
2.4 V
Write data
0.8 V
MB90570 Series
(8) Ready Input Timing
Parameter
Symbol
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
RDY setup time
tRYHS
RDY
RDY hold time
tRYHH
RDY
—
45
—
ns
0
—
ns
Note : Use the automatic ready function when the setup time for the rising edge of the RDY signal is not sufficient.
2.4 V
2.4 V
CLK
ALE
RD/WRL, RD/WRH
tRYHS
RDY
(wait inserted)
tRYHS
0.2 VCC
RDY
(wait not inserted)
0.8 VCC
0.2 VCC
0.8 VCC
tRYHH
(9) Hold Timing
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
Parameter
Symbol
Pins in floating status →
HAK ↓ time
tXHAL
HAK
HAK ↑ → pin valid time
tHAHV
HAK
—
30
1 tCP*
ns
1 tCP*
2 tCP*
ns
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
Note : More than 1 machine cycle is needed before HAK changes after HRQ pin is fetched.
HAK
2.4 V
0.8 V
tXHAL
Pins
2.4 V
0.8 V
tHAHV
High-Z
2.4 V
0.8 V
93
MB90570 Series
(10) UART0 (SCI), UART1 (SCI) Timing
Parameter
Symbol
Serial clock cycle time
tSCYC
SCK ↓ → SOT delay
time
tSLOV
Valid SIN → SCK ↑
tIVSH
SCK ↑ → valid SIN hold
time
tSHIX
Serial clock “H” pulse
width
tSHSL
Serial clock “L” pulse
width
tSLSH
SCK ↓ → SOT delay
time
tSLOV
Valid SIN → SCK ↑
tIVSH
SCK ↑ → valid SIN hold
time
tSHIX
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
8 tCP*
—
ns
– 80
80
ns
100
—
ns
60
—
ns
SCK0 to SCK4
4 tCP*
—
ns
SCK0 to SCK4
4 tCP*
—
ns
—
150
ns
60
—
ns
60
—
ns
SCK0 to SCK4
SCK0 to SCK4, Internal shift clock
SOT0 to SOT4 mode
SCK0 to SCK4, CL = 80 pF
+ 1 TTL for an
SIN0 to SIN4
output pin
SCK0 to SCK4,
SIN0 to SIN4
External shift
clock mode
SCK0 to SCK4,
CL = 80 pF
SOT0 to SOT4
+ 1 TTL for an
SCK0 to SCK4, output pin
SIN0 to SIN4
SCK0 to SCK4,
SIN0 to SIN4
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
Notes : • These are AC ratings in the CLK synchronous mode.
• CL is the load capacitance value connected to pins while testing.
94
MB90570 Series
• Internal shift clock mode
tSCYC
SCK0 to SCK4
2.4 V
0.8 V
0.8 V
tSLOV
2.4 V
SOT0 to SOT4
0.2 V
tIVSH
SIN0 to SIN4
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
• External shift clock mode
tSLSH
SCK0 to SCK4
0.2 VCC
tSHSL
0.8 VCC
0.8 VCC
0.2 VCC
tSLOV
SOT0 to SOT4
2.4 V
0.8 V
tIVSH
SIN0 to SIN4
tSHIX
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
95
MB90570 Series
(11) Timer Input Timing
Parameter
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
Symbol
tTIWH,
tTIWL
Input pulse width
IN0, IN1
—
4 tCP*
—
ns
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
0.8 VCC
0.8 VCC
0.2 VCC
0.2 VCC
IN0, IN1
tTIWH
(12) Timer Output Timing
Parameter
CLK ↑ → TOUT
transition time
Symbol
tTIWL
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
OUT0 to OUT3,
PPG0, PPG1
tTO
—
2.4 V
CLK
tTO
TOUT
96
2.4 V
0.8 V
30
—
ns
MB90570 Series
(13) Trigger Input Timing
Parameter
Symbol
Input pulse width
tTRGH
tTRGL
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit
Remarks
Min
Max
IRQ0 to IRQ7,
ADTG, IN0, IN1
—
IRQ0 to IRQ5
5 tCP *
—
ns
Under normal
operation
1
—
µs
In stop mode
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
0.8 VCC
0.8 VCC
0.2 VCC
IRQ0 to IRQ7
ADTG, IN0, IN1
tTRGH
0.2 VCC
tTRGL
97
MB90570 Series
(14) Chip Select Output Timing
Parameter
Symbol
(AVCC = VCC = 5.0 V ±10%, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Pin name
Condition
Unit Remarks
Min
Max
Valid chip select output
→ Valid data input time
tSVDV
CS0 to CS7,
AD15 to AD00
RD ↑ → chip select
output effective time
tRHSV
RD,
CS0 to CS7
WR ↑ → chip select
output effective time
tWHSV
CS0 to CS7,
WRL, WRH
Valid chip select output
→ CLK ↑ time
tSVCH
CLK,
CS0 to CS7
—
5 tCP*/2 – 60
ns
1 tCP*/2 – 10
—
ns
1 tCP*/2 – 10
—
ns
1 tCP*/2 – 20
—
ns
—
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
tSVCH
CLK
2.4 V
RD
2.4 V
tRHSV
A23 to A16
CS0 to CS7
2.4 V
0.8 V
tSVDV
AD15 to AD00
2.4 V
0.8 V
Read data
tWHSV
WRL, WRH
2.4 V
AD15 to AD00
98
Write data
MB90570 Series
(15) I2C Timing
Parameter
Symbol
Internal clock cycle time
tCP
Start condition output
tSTAO
Stop condition output
tSTOO
Start condition detection
(AVCC = VCC = 2.7 V to 5.5 V, AVSS = VSS = 0.0 V, TA = –40°C to +85°C)
Value
Unit
Remarks
Pin name Condition
Min
Max
—
62.5
666
tCP×m×n/2-20 tCP×m×n/2+20
ns
ns
Only as master
tCP(m×n/
2+4)-20
tCP(m×n/
2+4)+20
ns
tSTAI
3tCP+40
—
ns
Stop condition detection
tSTOI
3tCP+40
—
ns
SCL output “L” width
tLOWO
SDA,SCL
All products
Only as slave
tCP×m×n/2-20 tCP×m×n/2+20
SCL
SCL output “H” width
SDA output delay time
Setup after SDA output
interrupt period
SCL input “L” width
tHIGHO
—
tDOO
ns
Only as master
tCP(m×n/
2+4)-20
tCP(m×n/
2+4)+20
ns
2tCP-20
2tCP+20
ns
4tCP-20
—
ns
3tCP+40
—
ns
tCP+40
—
ns
40
—
ns
0
—
ns
SDA,SCL
tDOSUO
tLOWI
SCL
SCL input “H” width
SDA input setup time
tHIGHI
tSUI
SDA,SCL
SDA input hold time
tHOI
Notes : • “m” and “n” in the above table represent the values of shift clock frequency setting bits (CS4-CS0) in
the clock control register “ICCR”. For details, refer to the register description in the hardware manual.
• tDOSUO represents the minimum value when the interrupt period is equal to or greater than the SCL “L” width.
• The SDA and SCL output values indicate that rise time is 0 ns.
• For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
99
MB90570 Series
• I2C interface [data transmitter (master/slave)]
tLOWO
tHIGHO
0.8 VCC
SCL
0.8 VCC
0.8 VCC
0.2 VCC
1
tSTAO
0.8 VCC
0.8 VCC
0.2 VCC
8
tDOO
9
tDOO
tSUI
SDA
tHOI
tDOSUO
ACK
• I2C interface [data receiver (master/slave)]
tHIGHI
0.8 VCC
SCL
tLOWI
0.8 VCC
0.8 VCC
0.2 VCC
6
7
tSUI
SDA
100
tHOI
0.2 VCC
8
0.2 VCC
0.2 VCC
9
tSTOI
tDOO
tDOO
ACK
tDOSUO
MB90570 Series
(16) Pulse Width on External Interrupt Pin at Return from STOP Mode
(AVCC = VCC = 2.7 V to 5.5 V, AVSS = VSS = 0.0 V, TA = −40 °C to +85 °C)
Value
Parameter
Symbol
Pin name
Condition
Unit
Remarks
Min
Max
Input pulse width
tIRQWH
tIRQWL
IRQ2 to IRQ7

6tCP *

ns
* : For tCP (internal operating clock cycle time), refer to “(3) Clock Timings.”
0.80.8
VCCVCC
0.80.8
VCCVCC
0.20.2
VCCVCC
IRQ2
IRQ2
∼ IRQ7
∼ IRQ7
tIRQWH
tIRQWH
0.20.2
VCCVCC
tIRQWL
tIRQWL
101
MB90570 Series
5. A/D Converter Electrical Characteristics
Parameter
Resolution
—
—
—
8/10
—
bit
Total error
—
—
—
—
±5.0
LSB
Non-linear error
—
—
—
—
±2.5
LSB
Differential
linearity error
—
—
—
—
±1.9
LSB
Zero transition
voltage
VOT
AN0 to
AN7
–3.5 LSB +0.5 LSB +4.5 LSB
mV
Full-scale
transition voltage
VFST
AN0 to
AN7
AVRH
AVRH
AVRH
–6.5 LSB –1.5 LSB +1.5 LSB
mV
—
A/D conversion
time
—
—
VCC = 5.0 V ±10%
at machine clock of 16 MHz
416tCP
—
—
µs
Sampling period
—
—
VCC = 5.0 V ±10% at machine
clock of 6 MHz
64tCP
—
—
µs
Analog port
input current
IAIN
AN0 to
AN7
—
—
10
µA
Analog input
voltage
VAIN
AN0 to
AN7
AVRL
—
AVRH
V
—
AVRH
AVRL
+3.0
—
AVCC
V
—
AVRL
0
—
AVRH
–3.0
V
IA
AVCC
—
5
—
mA
IAH
AVCC
CPU stopped and 8/10-bit
A/D converter not in operation
(VCC = AVCC = AVRH = 5.0 V)
—
—
5
µA
IR
AVRH
—
—
400
—
µA
IRH
AVRH
CPU stopped and 8/10-bit
A/D converter not in operation
(VCC = AVCC = AVRH = 5.0 V)
—
—
5
µA
—
AN0 to
AN7
—
—
—
4
LSB
Reference
voltage
Power supply
current
Reference
voltage supply
current
Offset between
channels
102
(AVCC = VCC = 2.7 V to 5.5 V, AVSS = VSS = 0.0 V, 2.7 V ≤ AVRH – AVRL, TA = –40°C to +85°C)
Value
Symbol Pin name
Condition
Unit
Min
Typ
Max
—
MB90570 Series
6. A/D Converter Glossary
Resolution: Analog changes that are identifiable with the A/D converter
Linearity error:The deviation of the straight line connecting the zero transition point (“00 0000 0000” ↔ “00 0000
0001”) with the full-scale transition point (“11 1111 1110” ↔ “11 1111 1111”) from actual conversion characteristics
Differential linearity error:The deviation of input voltage needed to change the output code by 1 LSB from the
theoretical value
Total error:The total error is defined as a difference between the actual value and the theoretical value, which
includes zero-transition error/full-scale transition error and linearity error.
Total error
3FF
3FE
0.5 LSB
Actual conversion
value
Digital output
3FD
{1 LSB × (N – 1) + 0.5 LSB}
004
VNT
(measured value)
003
Actual conversion
characteristics
002
Theoretical
characteristics
001
0.5 LSB
AVRL
1 LSB = (Theoretical value)
AVRH – AVRL
[V]
1024
VOT (Theoretical value) = AVRL + 0.5 LSB[V]
Analog input
AVRH
Total error for digital output N =
VNT – {1 LSB × (N – 1) + 0.5 LSB}
[LSB]
1 LSB
VNT: Voltage at a transition of digital output from (N – 1) to N
VFST (Theoretical value) = AVRH – 1.5 LSB[V]
(Continued)
103
MB90570 Series
(Continued)
Linearity error
Differential linearity error
Theoretical characteristics
3FF
Actual conversion
value
{1 LSB × (N – 1)+ VOT}
3FE
N+1
Actual conversion value
VFST
(measured value)
VNT
004
Actual conversion
characteristics
003
Digital output
Digital output
3FD
N
N–1
V(N + 1)T
(measured value)
N–2
VNT (measured value)
002
Theoretical
characteristics
001
Actual conversion
value
VOT (measured value)
AVRL
Analog input
AVRH
VNT – {1 LSB × (N – 1) + VOT}
Linearity error of
[LSB]
=
1 LSB
digital output N
Differential linearity error
=
of digital N
1 LSB =
V(N + 1)T – VNT
1 LSB
– 1 LSB [LSB]
VFST – VOT
[V]
1022
VOT:Voltage at transition of digital output from “000H” to “001H”
VFST:Voltage at transition of digital output from “3FEH” to “3FFH”
104
AVRL
Analog input
AVRH
MB90570 Series
7. Notes on Using A/D Converter
Select the output impedance value for the external circuit of analog input according to the following conditions.
Output impedance values of the external circuit MB90V570/V570A/573/574 are 5 kΩ or lower, MB90F574/574A/
574C are 10 kΩ or lower are recommended.
When capacitors are connected to external pins, the capacitance of several thousand times the internal capacitor
value is recommended to minimized the effect of voltage distribution between the external capacitor and internal
capacitor.
When the output impedance of the external circuit is too high, the sampling period for analog voltages may not
be sufficient (sampling period = 4.00 µs @machine clock of 16 MHz).
• Equipment of analog input circuit model
C0
Analog input
Comparator
C1
MB90573/4, MB90V570/A R ≅ 3.2 kΩ, C ≅ 30 pF
MB90F574/A
R ≅ 7.1 kΩ, C ≅ 48.3 pF
MB90574C
R ≅ 2.2 kΩ, C ≅ 45 pF
Note : Listed values must be considered as standards.
• Error
The smaller the | AVRH – AVRL |, the greater the error would become relatively.
105
MB90570 Series
8. D/A Converter Electrical Characteristics
Parameter
(AVCC = VCC = DVCC = 5.0 V ±10%, AVSS = VSS = DVSS = 0.0 V, TA = –40°C to +85°C)
Value
Symbol
Pin name
Unit
Remarks
Min
Typ
Max
Resolution
—
—
—
8
—
bit
Differential linearity
error
—
—
—
—
±0.9
LSB
Absolute accuracy
—
—
—
—
±1.2
%
Linearity error
—
—
—
—
±1.5
LSB
Conversion time
—
—
—
10
20
µs
Analog reference
voltage
—
DVCC
VSS + 3.0
—
AVCC
V
IDVR
DVCC
—
120
300
µA
Conversion under
no load
IDVRS
DVCC
—
—
10
µA
In sleep mode
—
20
—
kΩ
Reference voltage
supply current
Analog output
impedance
—
—
Load capacitance: 20 pF
9. Flash Memory Program/Erase Characteristics
Parameter
Condition
Sector erase time
Chip erase time
TA = + 25°C
VCC = 5.0 V
Word (16bit width)
programming time
106
Value
Unit
Remarks
Min
Typ
Max
—
1.5
30
s
Except for the write time before
internal erase operation
—
13.5
—
s
Except for the write time before
internal erase operation
—
32
1,000
µs
Except for the over head time of
the system
Program/Erase time
—
10,000
—
—
cycle
Data hold time
—
100,000
—
—
h
MB90570 Series
■ EXAMPLE CHARACTERISTICS
(1) Power Supply Current (MB90574)
ICC - VCC
ICC (mA)
35
ICCS - VCC
ICCS (mA)
10
TA = +25°C
TA = +25°C
9
30
Fc = 16 MHz
25
Fc = 12.5 MHz
8
Fc = 16 MHz
7
Fc = 12.5 MHz
6
20
Fc = 10 MHz
15
Fc = 8 MHz
10
Fc = 5 MHz
Fc = 4 MHz
Fc = 2 MHz
5
5
Fc = 10 MHz
4
Fc = 8 MHz
3
Fc = 5 MHz
Fc = 4 MHz
Fc = 2 MHz
2
1
3.0
4.0
5.0
ICC - TA
ICC (mA)
35
3.0
6.0
VCC (V)
5.0
6.0
VCC (V)
ICCS - TA
ICCS (mA)
10
VCC = 5.0 V
4.0
VCC = 5.0 V
9
30
Fc = 16 MHz
8
Fc = 12.5 MHz
7
25
20
Fc = 10 MHz
Fc = 16 MHz
Fc = 12.5 MHz
6
Fc = 10 MHz
5
15
Fc = 8 MHz
10
Fc = 5 MHz
Fc = 4 MHz
Fc = 2 MHz
5
Fc = 8 MHz
4
Fc = 5 MHz
Fc = 4 MHz
Fc = 2 MHz
3
2
1
–20
+10
+40
+70
+100
TA (°C)
ICCLS (mA)
70
ICCL - VCC
ICCL (µA)
160
–20
+10
+40
+70
+100
TA (°C)
ICCLS - VCC
TA = +25°C
TA = +25°C
60
140
Fc = 8 kHz
120
100
50
Fc = 8 kHz
40
80
30
60
20
40
10
20
3.0
4.0
5.0
6.0
VCC (V)
3.0
4.0
5.0
6.0
VCC (V)
(Continued)
107
MB90570 Series
ICC - Fc
ICC (mA)
35
ICCS - Fc
ICCS (mA)
10
TA = +25°C
30
25
20
15
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
9
7
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
6
VCC = 3.0 V
VCC = 2.5 V
5
VCC = 2.5 V
TA = +25°C
8
4
3
10
2
5
1
4.0
6.0
8.0
ICCT - VCC
ICCT (µA)
20
4.0
12.0 16.0
Fc (MHz)
TA = +25°C
9
16
8
14
Fc = 8 kHz
6
10
5
8
4
6
3
4
2
2
1
4.0
5.0
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
8
7
6
5
4
7
6
5
4
3
2
1
1
+70
+100
TA (°C)
6.0
VCC (V)
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
8
2
+40
5.0
9
3
+10
4.0
ICCLH - TA
ICCLH (µA)
10
9
–20
TA = +25°C
3.0
6.0
VCC (V)
ICCT - TA
ICCT (µA)
10
12.0 16.0
Fc (MHz)
7
12
3.0
8.0
ICCH - VCC
ICCH (µA)
10
18
6.0
–20
+10
+40
+70
+100
TA (°C)
(Continued)
108
MB90570 Series
(Continued)
ICCL - TA
ICCL (µA)
20
ICCLS - TA
ICCLS (µA)
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
18
16
14
12
10
14
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
12
10
8
8
6
6
4
4
2
2
–20
+10
+40
+70
+100
TA (°C)
–20
+10
+40
+70
+100
TA (°C)
109
MB90570 Series
(2) Power Supply Current (MB90F574)
ICCS - VCC
ICC - VCC
ICCS (mA)
ICC (mA)
140
40
TA = +25°C
TA = +25°C
Fc = 16 MHz
120
35
Fc = 12.5 MHz
100
Fc = 10 MHz
Fc = 8 MHz
80
60
Fc = 5 MHz
Fc = 4 MHz
40
Fc = 2 MHz
20
30
Fc = 16 MHz
25
Fc = 12.5 MHz
20
Fc = 10 MHz
Fc = 8 MHz
15
Fc = 5 MHz
Fc = 4 MHz
Fc = 2 MHz
10
5
3.0
4.0
5.0
ICC - TA
6.0
VCC (V)
3.0
4.0
5.0
6.0
VCC (V)
ICCS - TA
ICC (mA)
120
ICCS (mA)
40
VCC = 5.0 V
VCC = 5.0 V
35
100
Fc = 16 MHz
30
Fc = 12.5 MHz
25
Fc = 10 MHz
Fc = 8 MHz
20
80
60
Fc = 10 MHz
Fc = 8 MHz
Fc = 5 MHz
Fc = 4 MHz
Fc = 2 MHz
Fc = 5 MHz
Fc = 4 MHz
10
20
Fc = 2 MHz
5
+10
+40
+70
+100
TA (°C)
Fc = 12.5 MHz
15
40
–20
Fc = 16 MHz
–20
+10
+40
+70
+100
TA (°C)
(Continued)
110
MB90570 Series
ICCLS - VCC
ICCLS (µA)
200
TA = +25°C
180
160
FC = 8 kHz
140
120
100
80
60
40
20
3.0
4.0
5.0
6.0
VCC (V)
ICCS - FC
ICC - FC
ICC (mA)
120
VCC = 6.0 V
TA = +25°C
ICCS (mA)
40
TA = +25°C
35
100
VCC = 5.5 V
80
VCC = 5.0 V
30
VCC = 6.0 V
VCC = 4.5 V
25
VCC = 5.5 V
60
VCC = 4.0 V
20
VCC = 5.0 V
40
VCC = 3.5 V
VCC = 3.0 V
15
20
VCC = 2.5 V
4.0
8.0
12.0
10
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
5
VCC = 2.5 V
4.0
16.0
FC (MHZ)
ICCT - VCC
ICCT (µA)
50
8.0
12.0
16.0
FC (MHZ)
ICCH -VCC
ICCH (µA)
10
9
TA = +25°C
40
TA = +25°C
8
FC = 8 kHZ
7
6
30
5
20
4
3
2
10
1
3
4
5
6
VCC (V)
3.0
4.0
5.0
6.0
VCC (V)
(Continued)
111
MB90570 Series
(Continued)
ICCT - TA
ICCT (µA)
10
ICCH - TA
ICCH (µA)
10
9
9
8
8
7
7
6
6
5
5
4
4
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
3
2
1
-20
+10
+40
3
2
1
+70 +100
TA (°C)
+10
-20
+40
ICCLS - TA
ICCLS (µA)
20
18
16
VCC = 6.0 V
14
VCC = 5.5 V
VCC = 5.0 V
12
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
10
8
6
4
2
-20
112
+10
+40
+70
+100
TA (°C)
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
VCC = 2.5 V
+70 +100
TA (°C)
MB90570 Series
(3) Power Supply Current (MB90574C)
ICC (mA)
70
TA = +25 °C
ICC - VCC
60
FC = 16 MHz
50
FC = 12 MHz
40
FC = 10 MHz
FC = 8 MHz
30
FC = 5 MHz
FC = 4 MHz
FC = 2 MHz
20
10
0
3.0
3.5
4.0
4.5
ICC (mA)
70
5.0
ICC - FC
5.5
6.0
VCC (V)
TA = +25 °C
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
60
50
40
30
20
10
0
2
ICCS (mA)
18
16
14
12
10
8
6
4
2
0
−50
4
6
8
10
ICCS - TA
12
14 16
FC (MHz)
VCC = 5 V
FC = 16 MHz
FC = 12 MHz
FC = 10 MHz
FC = 8 MHz
FC = 4 MHz
FC = 2 MHz
−20
10
40
70
100
TA (°C)
ICC (mA)
50
45
40
35
30
25
20
15
10
5
0
−50
ICC - TA
VCC = 5.0 V
FC = 16 MHz
FC = 12 MHz
FC = 10 MHz
FC = 8 MHz
FC = 5 MHz
FC = 4 MHz
FC = 2 MHz
−20
ICCS (mA)
18
16
14
10
40
70
100
TA (°C)
TA = +25 °C
FC = 16 MHz
ICCS - VCC
FC = 12 MHz
FC = 10 MHz
12
10
8
FC = 8 MHz
FC = 5 MHz
6
FC = 4 MHz
4
FC = 2 MHz
2
0
3.000 3.500 4.000 4.500 5.000 5.500 6.000
VCC (V)
ICCS (mA)
18
16
14
12
10
8
6
4
2
0
2
ICCS - FC
TA = +25 °C
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
4
6
8
10
12
14
16
FC (MHz)
(Continued)
113
MB90570 Series
ICCH (µA)
ICCH - VCC
TA = +25 °C
10
9
8
7
6
5
4
3
2
1
0
3.000 3.500 4.000 4.500 5.000 5.500 6.000
VCC (V)
ICCH (µA)
10
9
8
7
6
5
4
3
2
1
0
−50
−20
ICCH - TA
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
10
40
70
ICCT (µA)
ICCT - VCC
TA = +25 °C
10
9
8
7
6
5
4
3
2
1
FC = 8 kHz
0
3.000 3.500 4.000 4.500 5.000 5.500 6.000
VCC (V)
ICCT (µA)
10
9
8
7
6
5
4
3
2
1
0
−50
−20
ICCT - TA
ICCL (µA)
70
ICCL (µA)
70
ICCL - TA
ICCL - VCC
TA = +25 °C
60
60
50
50
40
40
30
FC = 8 kHz
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
10
40
70
20
10
10
0
−50
100
TA (°C)
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
30
20
0
3.000 3.500 4.000 4.500 5.000 5.500 6.000
VCC (V)
100
TA (°C)
−20
10
40
70
100
TA (°C)
(Continued)
114
MB90570 Series
(Continued)
ICCLS (µA)
25
ICCLS - VCC
TA = +25 °C
ICCLS (µA)
25
20
20
15
15
10
FC = 8 kHz
ICCLS - TA
VCC = 6.0 V
VCC = 5.5 V
VCC = 5.0 V
VCC = 4.5 V
VCC = 4.0 V
VCC = 3.5 V
VCC = 3.0 V
10
5
5
0
3.000 3.500 4.000 4.500 5.000 5.500 6.000
VCC (V)
0
−50
−20
10
40
70
100
TA (°C)
115
MB90570 Series
■ ORDERING INFORMATION
Part number
116
Package
MB90573PFF
MB90574PFF
MB90F574PFF
MB90F574APFF
120-pin Plastic LQFP
(FPT-120P-M05)
MB90573PFV
MB90574PFV
MB90574CPFV
MB90F574PFV
MB90F574APFV
120-pin Plastic QFP
(FPT-120P-M13)
MB90574CPMT
MB90F574APMT
120-pin Plastic LQFP
(FPT-120P-M21)
Remarks
MB90570 Series
■ PACKAGE DIMENSIONS
120-pin plastic LQFP
(FPT-120P-M05)
16.00±0.20(.630±.008)SQ
14.00±0.10(.551±.004)SQ
90
61
91
60
0.08(.003)
Details of "A" part
+0.20
1.50 –0.10
+.008
(Mounting height)
.059 –.004
INDEX
120
31
"A"
0~8°
LEAD No.
1
0.40(.016)
30
0.16±0.03
(.006±.001)
0.07(.003)
M
0.145±0.055
(.006±.002)
0.50±0.20
(.020±.008)
0.45/0.75
(.018/.030)
C
0.10±0.10
(.004±.004)
(Stand off)
0.25(.010)
1998 FUJITSU LIMITED F120006S-3C-4
Dimensions in mm (inches)
(Continued)
117
MB90570 Series
120-pin plastic QFP
(FPT-120P-M13)
22.60±0.20(.890±.008)SQ
20.00±0.10(.787±.004)SQ
90
0.145±0.055
(.006±.002)
61
91
60
0.08(.003)
Details of "A" part
+0.32
3.53 –0.20
+.013
.139 –.008
(Mouting height)
+0.10
0.20 –0.15
+.004
0°~8°
INDEX
31
120
"A"
LEAD No.
1
30
0.50(.020)
C
.008 –.006
(Stand off)
0.22±0.05
(.009±.002)
0.08(.003)
0.50±0.20
(.020±.008)
0.60±0.15
(.024±.006)
0.25(.010)
M
2000 FUJITSU LIMITED F120013S-c-3-5
Dimensions in mm (inches)
(Continued)
118
MB90570 Series
(Continued)
120-pin plastic LQFP
(FPT-120P-M21)
18.00±0.20(.709±.008)SQ
16.00±0.10(.630±.004)SQ
90
61
91
60
0.08(.003)
Details of "A" part
+0.20
1.50 –0.10
+.008
(Mounting height)
.059 –.004
INDEX
0~8°
120
LEAD No.
1
30
0.50(.020)
C
"A"
31
0.22±0.05
(.009±.002)
0.08(.003)
M
0.145
.006
+0.05
–0.03
+.002
–.001
0.60±0.15
(.024±.006)
0.10±0.05
(.004±.002)
(Stand off)
0.25(.010)
2001 FUJITSU LIMITED F120033S-c-3-3
Dimensions in mm (inches)
119
MB90570 Series
FUJITSU LIMITED
For further information please contact:
Japan
FUJITSU LIMITED
Marketing Division
Electronic Devices
Shinjuku Dai-Ichi Seimei Bldg. 7-1,
Nishishinjuku 2-chome, Shinjuku-ku,
Tokyo 163-0721, Japan
Tel: +81-3-5322-3353
Fax: +81-3-5322-3386
http://edevice.fujitsu.com/
North and South America
FUJITSU MICROELECTRONICS AMERICA, INC.
3545 North First Street,
San Jose, CA 95134-1804, U.S.A.
Tel: +1-408-922-9000
Fax: +1-408-922-9179
Customer Response Center
Mon. - Fri.: 7 am - 5 pm (PST)
Tel: +1-800-866-8608
Fax: +1-408-922-9179
http://www.fma.fujitsu.com/
Europe
FUJITSU MICROELECTRONICS EUROPE GmbH
Am Siebenstein 6-10,
D-63303 Dreieich-Buchschlag,
Germany
Tel: +49-6103-690-0
Fax: +49-6103-690-122
http://www.fme.fujitsu.com/
Asia Pacific
FUJITSU MICROELECTRONICS ASIA PTE. LTD.
#05-08, 151 Lorong Chuan,
New Tech Park,
Singapore 556741
Tel: +65-281-0770
Fax: +65-281-0220
http://www.fmal.fujitsu.com/
Korea
FUJITSU MICROELECTRONICS KOREA LTD.
1702 KOSMO TOWER, 1002 Daechi-Dong,
Kangnam-Gu,Seoul 135-280
Korea
Tel: +82-2-3484-7100
Fax: +82-2-3484-7111
F0111
 FUJITSU LIMITED Printed in Japan
All Rights Reserved.
The contents of this document are subject to change without notice.
Customers are advised to consult with FUJITSU sales
representatives before ordering.
The information and circuit diagrams in this document are
presented as examples of semiconductor device applications, and
are not intended to be incorporated in devices for actual use. Also,
FUJITSU is unable to assume responsibility for infringement of
any patent rights or other rights of third parties arising from the use
of this information or circuit diagrams.
The products described in this document are designed, developed
and manufactured as contemplated for general use, including
without limitation, ordinary industrial use, general office use,
personal use, and household use, but are not designed, developed
and manufactured as contemplated (1) for use accompanying fatal
risks or dangers that, unless extremely high safety is secured, could
have a serious effect to the public, and could lead directly to death,
personal injury, severe physical damage or other loss (i.e., nuclear
reaction control in nuclear facility, aircraft flight control, air traffic
control, mass transport control, medical life support system, missile
launch control in weapon system), or (2) for use requiring
extremely high reliability (i.e., submersible repeater and artificial
satellite).
Please note that Fujitsu will not be liable against you and/or any
third party for any claims or damages arising in connection with
above-mentioned uses of the products.
Any semiconductor devices have an inherent chance of failure. You
must protect against injury, damage or loss from such failures by
incorporating safety design measures into your facility and
equipment such as redundancy, fire protection, and prevention of
over-current levels and other abnormal operating conditions.
If any products described in this document represent goods or
technologies subject to certain restrictions on export under the
Foreign Exchange and Foreign Trade Law of Japan, the prior
authorization by Japanese government will be required for export
of those products from Japan.