TI LP2985-33DBVR 150-ma low-noise low-dropout regulator with shutdown Datasheet

LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
FEATURES
PORTABLE APPLICATIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Output Tolerance of
– 1% (A Grade)
– 1.5% (Standard Grade)
Ultra-Low Dropout, Typically
– 280 mV at Full Load of 150 mA
– 7 mV at 1 mA
Wide VIN Range…16 V Max
Low IQ . . . 850 µA at Full Load at 150 mA
Shutdown Current . . . 0.01 µA Typ
Low Noise . . . 30 µVRMS With 10-nF Bypass
Capacitor
Stable With Low-ESR Capacitors, Including
Ceramic
Overcurrent and Thermal Protection
High Peak-Current Capability
Cellular Phones
Palmtop and Laptop Computers
Personal Digital Assistants (PDAs)
Digital Cameras and Camcorders
CD Players
MP3 Players
DBV (SOT-23) PACKAGE
(TOP VIEW)
VIN
GND
ON/OFF
1
5
VOUT
4
BYPASS
2
3
DESCRIPTION/ORDERING INFORMATION
The LP2985 family of fixed-output, low-dropout regulators offers exceptional, cost-effective performance for both
portable and nonportable applications. Available in voltages of 1.8 V, 2.5 V, 2.8 V, 2.9 V, 3 V, 3.3 V and 5 V, the
family has an output tolerance of 1% for the A version (1.5% for the non-A version) and is capable of delivering
150-mA continuous load current. Standard regulator features, such as overcurrent and overtemperature
protection, are included.
The LP2985 has a host of features that makes the regulator an ideal candidate for a variety of portable
applications:
• Low dropout: A PNP pass element allows a typical dropout of 280 mV at 150-mA load current and 7 mV at
1-mA load.
• Low quiescent current: The use of a vertical PNP process allows for quiescent currents that are considerably
lower than those associated with traditional lateral PNP regulators.
• Shutdown: A shutdown feature is available, allowing the regulator to consume only 0.01 µA when the
ON/OFF pin is pulled low.
• Low-ESR-capacitor friendly: The regulator is stable with low-ESR capacitors, allowing the use of small,
inexpensive, ceramic capacitors in cost-sensitive applications.
• Low noise: A BYPASS pin allows for low-noise operation, with a typical output noise of 30 µVRMS, with the
use of a 10-nF bypass capacitor.
• Small packaging: For the most space-constrained needs, the regulator is available in the SOT-23 package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2006, Texas Instruments Incorporated
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
ORDERING INFORMATION
TJ
PART
GRADE
VOUT
(NOM)
PACKAGE (1)
1.8 V
2.5 V
2.8 V
A grade:
1% tolerance
2.9 V
3.0 V
3.3 V
5.0 V
–40°C to 125°C
SOT-23-5 – DBV
1.8 V
2.5 V
2.8 V
Standard grade:
1.5% tolerance
2.9 V
3.0 V
3.3 V
5.0 V
(1)
(2)
2
ORDERABLE
PART NUMBER
Reel of 3000
LP2985A-18DBVR
Reel of 250
LP2985A-18DBVT
Reel of 3000
LP2985A-25DBVR
Reel of 250
LP2985A-25DBVT
Reel of 3000
LP2985A-28DBVR
Reel of 250
LP2985A-28DBVT
Reel of 3000
LP2985A-29DBVR
Reel of 250
LP2985A-29DBVT
Reel of 3000
LP2985A-30DBVR
Reel of 250
LP2985A-30DBVT
Reel of 3000
LP2985A-33DBVR
Reel of 250
LP2985A-33DBVT
Reel of 3000
LP2985A-50DBVR
Reel of 250
LP2985A-50DBVT
Reel of 3000
LP2985-18DBVR
Reel of 250
LP2985-18DBVT
Reel of 3000
LP2985-25DBVR
Reel of 250
LP2985-25DBVT
Reel of 3000
LP2985-28DBVR
Reel of 250
LP2985-28DBVT
Reel of 3000
LP2985-29DBVR
Reel of 250
LP2985-29DBVT
Reel of 3000
LP2985-30DBVR
Reel of 250
LP2985-30DBVT
Reel of 3000
LP2985-33DBVR
Reel of 250
LP2985-33DBVT
Reel of 3000
LP2985-50DBVR
Reel of 250
LP2985-50DBVT
TOP-SIDE
MARKING (2)
LPT_
LPU_
LPJ_
LPZ_
LRA_
LPK_
LRI_
LPH_
LPL_
LPG_
LPM_
LPN_
LPF_
LPS_
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
The actual top-side marking has one additional character that designates the assembly/test site.
Submit Documentation Feedback
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
FUNCTIONAL BLOCK DIAGRAM
VIN
ON/OFF
1.23 V
VREF
−
+
BYPASS
VOUT
Overcurrent/
Overtemperature
Protection
BASIC APPLICATION CIRCUIT
LP2985
VIN
1
VOUT
5
2.2 µF
(see Note A)
1 µF
(see Note A)
GND
2
ON/OFF
(see Note B)
3
4
BYPASS
10 nF
(see Note C)
A.
Minimum COUT value for stability (can be increased without limit for improved stability and transient response)
B.
ON/OFF must be actively terminated. Connect to VIN if shutdown feature is not used.
C.
Optional BYPASS capacitor for low-noise operation
Submit Documentation Feedback
3
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
Absolute Maximum Ratings (1)
over virtual junction temperature range (unless otherwise noted)
MIN
MAX
VIN
Continuous input voltage range
–0.3
16
V
VON/OFF
ON/OFF input voltage range
–0.3
16
V
range (2)
–0.3
9
V
Input/output voltage differential range (3)
–0.3
16
V
Output voltage
VIN – VOUT
UNIT
Internally limited
(short-circuit protected)
IO
Output current (4)
θJA
Package thermal impedance (4) (5)
206
°C/W
TJ
Operating virtual junction temperature
150
°C
Tstg
Storage temperature range
150
°C
(1)
(2)
(3)
(4)
(5)
–65
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If load is returned to a negative power supply in a dual-supply system, the output must be diode clamped to GND.
The PNP pass transistor has a parasitic diode connected between the input and output. This diode normally is reverse biased
(VIN > VOUT), but will be forward biased if the output voltage exceeds the input voltage by a diode drop (see Application Information for
more details).
Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions
VIN
Supply input voltage
VON/OFF
ON/OFF input voltage
IOUT
Output current
TJ
Virtual junction temperature
(1)
4
MIN
MAX
2.2 (1)
16
0
VIN
V
150
mA
125
°C
–40
Recommended minimum VIN is the greater of 2.5 V or VOUT(max) + rated dropout voltage (max) for operating IL.
Submit Documentation Feedback
UNIT
V
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
Electrical Characteristics
at specified virtual junction temperature range, VIN = VOUT(NOM) + 1 V, VON/OFF = 2 V, CIN = 1 µF, IL = 1 mA, COUT = 4.7 µF
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
IL = 1 mA
∆VOUT
Output
voltage
tolerance
1 mA ≤ IL ≤ 50 mA
1 mA ≤ IL ≤ 150 mA
Line
regulation
VIN = [VOUT(NOM) + 1 V] to 16 V
Ground
pin
current
ON/OFF
input
current
–2.5
2.5
–3.5
3.5 %VNOM
25°C
–2.5
2.5
–3
3
–40°C to 125°C
–3.5
3.5
–4
4
25°C
0.007
–40°C to 125°C
1
3
7
10
0.007
1
3
7
10
15
60
40
90
120
150
120
350
280
65
120
–40°C to 125°C
75
350
–40°C to 125°C
120
25°C
850
110
220
400
600
350
1000
–40°C to 125°C
95
170
220
400
25°C
350
125
110
170
25°C
150
575
95
125
75
600
1500
850
1500
2500
25°C
0.01
0.8
0.01
0.8
–40°C to 105°C
0.05
2
0.05
2
5
25°C
–40°C to 125°C
5
1.4
1.4
1.6
25°C
1.6
0.55
–40°C to 125°C
25°C
25°C
0.15
0.15
0.01
–2
5
–40°C to 125°C
V
0.55
0.01
–40°C to 125°C
µA
1000
2500
–40°C to 125°C
mV
225
575
65
60
90
225
280
%/V
5
15
40
0.014
0.032
5
–40°C to 125°C
VON/OFF = LOW → O/P OFF
0.014
0.032
25°C
VON/OFF = HIGH → O/P ON
VON/OFF = 5 V
–40°C to 125°C
–40°C to 125°C
IL = 50 mA
VON/OFF = 0
2.5
25°C
VON/OFF < 0.15 V (OFF)
ION/OFF
1.5
–2.5
25°C
VON/OFF < 0.3 V (OFF)
ON/OFF
input
voltage (2)
–1.5
–40°C to 125°C
IL = 150 mA
VON/OFF
1
25°C
IL = 10 mA
UNIT
1.5
–40°C to 125°C
IL = 1 mA
MAX
–1
–40°C to 125°C
IL = 0
TYP
–1.5
25°C
IL = 150 mA
MIN
25°C
–40°C to 125°C
IL = 10 mA
LP2985-xx
MAX
25°C
25°C
IL = 50 mA
IGND
TYP
–40°C to 125°C
IL = 1 mA
Dropout
voltage (1)
LP2985A-xx
MIN
25°C
IL = 0
VIN – VOUT
TJ
–2
5
15
µA
15
Vn
Output
noise
(RMS)
BW = 300 Hz to 50 kHz,
COUT = 10 µF,
CBYPASS = 10 nF
25°C
30
30
µV
∆VOUT/∆VIN
Ripple
rejection
f = 1kHz, COUT = 10 µF,
CBYPASS = 10 nF
25°C
45
45
dB
(1)
(2)
Dropout voltage is defined as the input-to-output differential at which the output voltage drops 100 mV below the value measured with a
1-V differential.
The ON/OFF input must be driven properly for reliable operation (see Application Information).
Submit Documentation Feedback
5
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
Electrical Characteristics (continued)
at specified virtual junction temperature range, VIN = VOUT(NOM) + 1 V, VON/OFF = 2 V, CIN = 1 µF, IL = 1 mA, COUT = 4.7 µF
(unless otherwise noted)
PARAMETER
TJ
LP2985A-xx
MIN
TYP
LP2985-xx
MAX
MIN
TYP
MAX
UNIT
IOUT(PK)
Peak output
VOUT ≥ VO(NOM) – 5%
current
25°C
350
350
mA
IOUT(SC)
Short-circuit
RL = 0 (steady state) (3)
current
25°C
400
400
mA
(3)
6
TEST CONDITIONS
See Figure 5 in Typical Performance Characteristics.
Submit Documentation Feedback
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
OUTPUT VOLTAGE
vs
TEMPERATURE
DROPOUT VOLTAGE
vs
TEMPERATURE
0.45
3.345
VI = 4.3 V
VO = 3.3 V
Ci = 1 µF
Co = 4.7 µF
IO = 1 mA
150 mA
VO = 3.3 V
Cbyp = 10 nF
0.35
0.3
Dropout − V
Output Voltage − V
3.335
0.4
3.325
3.315
0.25
0.2
50 mA
0.15
0.1
3.305
10 mA
0.05
1 mA
3.295
−50
−25
0
25
50
75
100
125
0
−50
150
−25
0
Temperature − °C
0.45
Short-Circuit Current − A
0.4
Figure 2.
SHORT-CIRCUIT CURRENT
vs
TIME
SHORT-CIRCUIT CURRENT
vs
TIME
0.5
VI = 6 V
VO = 3.3 V
Ci = 1 µF
Cbyp = 0.01 µF
0.3
0.25
0.2
0.15
0.4
0.3
0.25
0.2
0.15
0.1
0.05
0.05
500
1000
Time − ms
1500
2000
150
0.35
0.1
0
125
VI = 16 V
VO = 3.3 V
Ci = 1 µF
Cbyp = 0.01 µF
0.45
0.35
0
−500
100
Figure 1.
Short-Circuit Current − A
0.5
25
50
75
Temperature − °C
0
−100
Figure 3.
100
300
Time − ms
500
700
Figure 4.
Submit Documentation Feedback
7
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
SHORT-CIRCUIT CURRENT
vs
OUTPUT VOLTAGE
GROUND-PIN CURRENT
vs
LOAD CURRENT
1200
320
VO = 3.3 V
300
1000
900
Ground Pin Current − µA
280
ISC − mA
VO = 3.3 V
Cbyp = 10 nF
1100
260
240
800
700
600
500
400
300
200
220
100
200
0
0
0.5
1
1.5
2
2.5
Output Voltage − V
3
3.5
60
80
100
Load Current − mA
Figure 6.
RIPPLE REJECTION
vs
FREQUENCY
RIPPLE REJECTION
vs
FREQUENCY
120
140
160
100
VI = 5 V
VO = 3.3 V
Co = 10 µF
Cbyp = 0 nF
80
70
80
50 mA
1 mA
60
50
40
150 mA
30
70
1 mA
60
50
30
20
10
10
0
100
1k
10k
100k
1M
50 mA
40
20
10
VI = 3.7 V
VO = 3.3 V
Co = 10 µF
Cbyp = 0 nF
90
Ripple Rejection − dB
90
150 mA
0
10
Frequency − Hz
100
1k
10k
Frequency − Hz
Figure 7.
8
40
Figure 5.
100
Ripple Rejection − dB
20
0
Figure 8.
Submit Documentation Feedback
100k
1M
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
RIPPLE REJECTION
vs
FREQUENCY
RIPPLE REJECTION
vs
FREQUENCY
100
100
VI = 5 V
VO = 3.3 V
Co = 4.7 µF
Cbyp = 10 nF
Ripple Rejection − dB
80
80
70
1 mA
60
50
40
50 mA
30
20
VI = 5 V
VO = 3.3 V
Co = 4.7 µF
Cbyp = 10 nF
90
Ripple Rejection − dB
90
70
1 mA
60
10 mA
50
40
100 mA
30
20
150 mA
10
10
0
0
10
100
1k
10k
100k
10
1M
100
Frequency − Hz
1
Figure 9.
Figure 10.
OUTPUT IMPEDANCE
vs
FREQUENCY
OUTPUT IMPEDANCE
vs
FREQUENCY
Ci = 1 µF
Co = 10 µF
VO = 3.3 V
1 mA
Output Impedance − Ω
Output Impedance − Ω
10
10 mA
100 mA
0.1
0.01
0.001
10
100
1k
10k
Frequency − Hz
1k
10k
100k
1M
10
Ci = 1 µF
Co = 4.7 µF
VO = 3.3 V
1
1 mA
100k
1M
100k
1M
10 mA
100 mA
0.1
0.01
0.001
10
100
1k
10k
Frequency − Hz
Frequency − Hz
Figure 11.
Figure 12.
Submit Documentation Feedback
9
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
OUTPUT NOISE DENSITY
vs
FREQUENCY
OUTPUT NOISE DENSITY
vs
FREQUENCY
10
10
ILOAD = 1 mA
Hz
1
Noise Density − µV/
Noise Density − µV/ Hz
ILOAD = 150 mA
Cbyp = 100 pF
Cbyp = 1 nF
0.1
Cbyp = 10 nF
1
Cbyp = 100 pF
Cbyp = 1 nF
0.1
Cbyp = 10 nF
0.01
0.01
100
1k
10k
Frequency − Hz
100
100k
1k
10k
Frequency − Hz
Figure 13.
Figure 14.
INPUT CURRENT
vs
INPUT VOLTAGE
GROUND-PIN CURRENT
vs
TEMPERATURE
1.8
100k
1400
VO = 3.3 V
Cbyp = 10 nF
1.6
RL = 3.3 kΩ
1200
VO = 3.3 V
Cbyp = 10 nF
150 mA
Ground Current − C
Input Current − mA
1.4
1.2
1
0.8
RL = Open
0.6
1000
800
600
1 mA
400
50 mA
0.4
0 mA
200
0.2
0
0
1
2
3
4
5
6
0
−50
Input Voltage − V
−25
0
25
50
75
Temperature − °C
Figure 15.
10
10 mA
Figure 16.
Submit Documentation Feedback
100
125
150
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
200
3.4
200
3.38
150
3.38
150
3.36
100
3.36
100
3.32
3.3
50
IL
VO = 3.3 V
Cbyp = 10 nF
∆IL = 100 mA
0
−50
VO
3.28
−100
3.26
−150
3.24
−200
3.22
−250
IL
3.34
3.32
3.3
VO = 3.3 V
Cbyp = 10 nF
∆IL = 150 mA
0
−50
VO
3.28
−100
3.26
−150
3.24
−200
3.22
−250
20 µs/div"
20 µs/div"
Figure 17.
Figure 18.
LOAD TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
3.4
200
3.38
150
3.36
100
3.41
5.5
3.39
5
VI
3.3
0
−50
VO
3.28
−100
3.26
−150
3.24
−200
3.22
−250
Output Voltage − V
3.32
VO = 3.3 V
Cbyp = 0 nF
∆IL = 150 mA
50
Load Current − mA
Output Voltage − V
3.37
IL
3.34
50
3.35
VO = 3.3 V
Cbyp = 0 nF
IO = 150 mA
4.5
4
3.5
3.33
3.31
VO
3
3.29
2.5
3.27
2
20 µs/div"
Input Voltage − V
3.34
Output Voltage − V
3.4
Load Current − mA
LOAD TRANSIENT RESPONSE
Load Current − mA
Output Voltage − V
LOAD TRANSIENT RESPONSE
20 µs/div"
Figure 19.
Figure 20.
Submit Documentation Feedback
11
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
LINE TRANSIENT RESPONSE
5.5
3.41
5.5
3.39
5
3.39
5
4.5
3.37
3.35
VO = 3.3 V
Cbyp = 10 nF
IO = 150 mA
4
3
3.31
3
2.5
3.29
3.31
3.27
4
3.5
3.5
VO
VO = 3.3 V
Cbyp = 0 nF
IO = 1 mA
4.5
3.33
3.33
3.29
3.35
VI
Input Voltage − V
VI
3.37
Output Voltage − V
3.41
Input Voltage − V
Output Voltage − V
LINE TRANSIENT RESPONSE
2.5
VO
3.27
2
2
20 µs/div"
20 µs/div"
Figure 21.
Figure 22.
LINE TRANSIENT RESPONSE
TURN-ON TIME
5.5
3.41
4
10
VO
3.39
5
3
4.5
2
3.33
VO = 3.3 V
Cbyp = 10 nF
IO = 1 mA
3.5
3.31
VO
3.27
6
0
−1
3
VO = 3.3 V
Cbyp = 0
IO = 150 mA
2
VON/OFF
2
−3
−4
100 µs/div"
0
100 µs/div"
Figure 23.
12
4
−2
2.5
3.29
1
Figure 24.
Submit Documentation Feedback
VON/OFF − V
4
3.35
Output Voltage − V
Output Voltage − V
3.37
Input Voltage − V
8
VIN
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
CIN = 1 µF, COUT = 4.7 µF, VIN = VOUT(NOM) + 1 V, TA = 25°C, ON/OFF pin tied to VIN (unless otherwise specified)
TURN-ON TIME
TURN-ON TIME
10
4
10
4
VO
VO
3
3
8
8
VO = 3.3 V
Cbyp = 100 pF
ILOAD = 150 mA
4
−2
VON/OFF
1
6
0
−1
VO = 3.3 V
Cbyp = 1 nF
ILOAD = 150 mA
4
VON/OFF
−2
2
2
−3
−3
0
−4
0
−4
2 ms/div"
200 µs/div"
Figure 25.
Figure 26.
TURN-ON TIME
4
Input
10
3
8
2
1
6
0
−1
4
VO = 3.3 V
Cbyp = 10 nF
ILOAD = 150 mA
VON/OFF − V
−1
Output Voltage − V
0
VON/OFF − V
6
Output Voltage − V
Output Voltage − V
1
VON/OFF − V
2
2
Output
−2
2
−3
0
−4
20 ms/div"
Figure 27.
Submit Documentation Feedback
13
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
APPLICATION INFORMATION
Capacitors
Input Capacitor (CIN)
A minimum value of 1 µF (over the entire operating temperature range) is required at the input of the LP2985. In
addition, this input capacitor should be located within 1 cm of the input pin and connected to a clean analog
ground. There are no equivalent series resistance (ESR) requirements for this capacitor, and the capacitance
can be increased without limit.
Output Capacitor (COUT)
As an advantage over other regulators, the LP2985 permits the use of low-ESR capacitors at the output,
including ceramic capacitors that can have an ESR as low as 5 mΩ. Tantalum and film capacitors also can be
used if size and cost are not issues. The output capacitor also should be located within 1 cm of the output pin
and be returned to a clean analog ground.
As with other PNP LDOs, stability conditions require the output capacitor to have a minimum capacitance and an
ESR that falls within a certain range.
• Minimum COUT: 2.2 µF (can be increased without limit to improve transient response stability margin)
• ESR range: see Figure 28 through Figure 30
Figure 29. 4.7-µF Stable ESR Range
for Output Voltage ≤2.3 V
ESR (Ω)
Figure 28. 2.2-µF Stable ESR Range
for Output Voltage ≤2.3 V
Figure 30. 2.2-µF/3.3-µF Stable ESR Range
for Output Voltage ≥2.5 V
It is critical that both the minimum capacitance and ESR requirement be met over the entire operating
temperature range. Depending on the type of capacitors used, both these parameters can vary significantly with
temperature (see capacitor characteristics).
14
Submit Documentation Feedback
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
APPLICATION INFORMATION (continued)
Noise Bypass Capacitor (CBYPASS)
The LP2985 allows for low-noise performance with the use of a bypass capacitor that is connected to the
internal bandgap reference via the BYPASS pin. This high-impedance bandgap circuitry is biased in the
microampere range and, thus, cannot be loaded significantly, otherwise, its output – and, correspondingly, the
output of the regulator – changes. Thus, for best output accuracy, dc leakage current through CBYPASS should be
minimized as much as possible and never should exceed 100 nA.
A 10-nF capacitor is recommended for CBYPASS. Ceramic and film capacitors are well suited for this purpose.
Capacitor Characteristics
Ceramics
Ceramic capacitors are ideal choices for use on the output of the LP2985 for several reasons. For capacitances
in the range of 2.2 µF to 4.7 µF, ceramic capacitors have the lowest cost and the lowest ESR, making them
choice candidates for filtering high-frequency noise. For instance, a typical 2.2-µF ceramic capacitor has an ESR
in the range of 10 mΩ to 20 mΩ and, thus, satisfies minimum ESR requirements of the regulator.
Ceramic capacitors have one major disadvantage that must be taken into account – a poor temperature
coefficient, where the capacitance can vary significantly with temperature. For instance, a large-value ceramic
capacitor (≥2.2 µF) can lose more than half of its capacitance as the temperature rises from 25°C to 85°C. Thus,
a 2.2-µF capacitor at 25°C drops well below the minimum COUT required for stability, as ambient temperature
rises. For this reason, select an output capacitor that maintains the minimum 2.2 µF required for stability over
the entire operating temperature range. Note that there are some ceramic capacitors that can maintain a ±15%
capacitance tolerance over temperature.
Tantalum
Tantalum capacitors can be used at the output of the LP2985, but there are significant disadvantages that could
prohibit their use:
• In the 1-µF to 4.7-µF range, tantalum capacitors are more expensive than ceramics of the equivalent
capacitance and voltage ratings.
• Tantalum capacitors have higher ESRs than their equivalent-sized ceramic counterparts. Thus, to meet the
ESR requirements, a higher-capacitance tantalum may be required, at the expense of larger size and higher
cost.
• The ESR of a tantalum capacitor increases as temperature drops, as much as double from 25°C to –40°C.
Thus, ESR margins must be maintained over the temperature range to prevent regulator instability.
ON/OFF Operation
The LP2985 allows for a shutdown mode via the ON/OFF pin. Driving the pin LOW (≤0.3 V) turns the device
OFF; conversely, a HIGH (≥1.6 V) turns the device ON. If the shutdown feature is not used, ON/OFF should be
connected to the input to ensure that the regulator is on at all times. For proper operation, do not leave ON/OFF
unconnected, and apply a signal with a slew rate of ≥40 mV/µs.
Reverse Input-Output Voltage
There is an inherent diode present across the PNP pass element of the LP2985.
VIN
VOUT
Submit Documentation Feedback
15
LP2985
150-mA LOW-NOISE LOW-DROPOUT REGULATOR
WITH SHUTDOWN
www.ti.com
SLVS522J – JULY 2004 – REVISED AUGUST 2006
APPLICATION INFORMATION (continued)
With the anode connected to the output, this diode is reverse biased during normal operation, since the input
voltage is higher than the output. However, if the output is pulled higher than the input for any reason, this diode
is forward biased and can cause a parasitic silicon-controlled rectifier (SCR) to latch, resulting in high current
flowing from the output to the input. Thus, to prevent possible damage to the regulator in any application where
the output may be pulled above the input, an external Schottky diode should be connected between the output
and input. With the anode on output, this Schottky limits the reverse voltage across the output and input pins to
∼0.3 V, preventing the regulator’s internal diode from forward biasing.
Schottky
VIN
VOUT
LP2985
16
Submit Documentation Feedback
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jan-2007
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LP2985-18DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-18DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-18DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-18DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-25DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-25DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-25DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-25DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-28DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-28DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-28DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-28DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-29DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-29DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-29DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-29DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-30DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-30DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-30DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-30DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-33DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-33DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-33DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-33DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-50DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jan-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LP2985-50DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-50DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985-50DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-18DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-18DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-18DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-18DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-25DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-25DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-25DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-25DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-28DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-28DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-28DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-28DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-29DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-29DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-29DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-29DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-30DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-30DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-30DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-30DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-33DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-33DBVRE4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-33DBVT
ACTIVE
SOT-23
DBV
5
250
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 2
Green (RoHS &
no Sb/Br)
Lead/Ball Finish
MSL Peak Temp (3)
PACKAGE OPTION ADDENDUM
www.ti.com
3-Jan-2007
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
LP2985A-33DBVTE4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-50DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-50DBVRG4
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-50DBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP2985A-50DBVTG4
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jun-2007
TAPE AND REEL INFORMATION
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
Device
9-Jun-2007
Package Pins
Site
Reel
Diameter
(mm)
Reel
Width
(mm)
A0 (mm)
B0 (mm)
K0 (mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LP2985-18DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-18DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-25DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-25DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-28DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-28DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-29DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-29DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-30DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-30DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-33DBVR
DBV
5
HNC
180
9
3.23
3.17
1.37
4
8
Q3
LP2985-33DBVR
DBV
5
NFME
0
0
3.23
3.17
1.37
4
8
Q3
LP2985-33DBVT
DBV
5
HNC
180
9
3.23
3.17
1.37
4
8
Q3
LP2985-33DBVT
DBV
5
NFME
330
16
10.6
15.8
4.9
16
24
Q3
LP2985-50DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985-50DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-18DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-18DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-25DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-25DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-28DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-28DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-29DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-29DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-30DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-30DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-33DBVR
DBV
5
HNC
180
9
3.23
3.17
1.37
4
8
Q3
LP2985A-33DBVR
DBV
5
NFME
0
0
3.23
3.17
1.37
4
8
Q3
LP2985A-33DBVT
DBV
5
HNC
180
9
3.23
3.17
1.37
4
8
Q3
LP2985A-33DBVT
DBV
5
NFME
330
16
10.6
15.8
4.9
16
24
Q3
LP2985A-50DBVR
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
LP2985A-50DBVT
DBV
5
LEN
180
9
3.15
3.2
1.4
4
8
Q3
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jun-2007
TAPE AND REEL BOX INFORMATION
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
LP2985-18DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985-18DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985-25DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985-25DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985-28DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985-28DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985-29DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985-29DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985-30DBVR
DBV
5
LEN
182.0
182.0
20.0
20.0
LP2985-30DBVT
DBV
5
LEN
182.0
182.0
LP2985-33DBVR
DBV
5
HNC
205.0
200.0
33.0
LP2985-33DBVR
DBV
5
NFME
185.0
185.0
220.0
LP2985-33DBVT
DBV
5
HNC
201.0
192.0
26.0
LP2985-33DBVT
DBV
5
NFME
0.0
0.0
0.0
LP2985-50DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985-50DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985A-18DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985A-18DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985A-25DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985A-25DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985A-28DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985A-28DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985A-29DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985A-29DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985A-30DBVR
DBV
5
LEN
182.0
182.0
20.0
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Jun-2007
Device
Package
Pins
Site
Length (mm)
Width (mm)
Height (mm)
LP2985A-30DBVT
DBV
5
LEN
182.0
182.0
20.0
LP2985A-33DBVR
DBV
5
HNC
205.0
200.0
33.0
LP2985A-33DBVR
DBV
5
NFME
185.0
185.0
220.0
LP2985A-33DBVT
DBV
5
HNC
201.0
192.0
26.0
LP2985A-33DBVT
DBV
5
NFME
0.0
0.0
0.0
LP2985A-50DBVR
DBV
5
LEN
182.0
182.0
20.0
LP2985A-50DBVT
DBV
5
LEN
182.0
182.0
20.0
Pack Materials-Page 4
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.
Customers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s
standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this
warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily
performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should
provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask
work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services
are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such
products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under
the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an
unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties
may be subject to additional restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service
voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business
practice. TI is not responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would
reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement
specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications
of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related
requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any
applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its
representatives against any damages arising out of the use of TI products in such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is
solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in
connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products
are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any
non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Telephony
www.ti.com/telephony
Low Power
Wireless
www.ti.com/lpw
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2007, Texas Instruments Incorporated