RoHS MB1505W-1510W SINGLE-PHASE BRIDGE RECTIFIER FEATURES Low cost This series is UL recognized under component index, file number E127707 High overload surge current capability Low thermal resistance. High isolation voltage from case to leads High temperature soldering guaranteed: 260/10 second, at 5 lbs. (2.3kg) tension. MECHANICAL DATA Case: Metal case Terminal: Plated lead 0.04" (1.02mm) diameter. Polarity: Polarity symbols marked on case. Mounting: Thru hole for #10 screw, 20 in,- lbs. Torqute Max. Weight: 0.93 ounce, 26.4gram O MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20% R T C E L SYMBOLS Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Output Current, at TC = 55 (Note 1, 2) Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Rating for Fusing (t<8.3ms) J E E Maximum Instantaneous Forward Voltage Drop per bridge element at 7.5A Maximum DC Reverse Current at rated TA = 25 DC blocking voltage per element TA Isolation Voltage from case to leads Typical Thermal Resistance (Note 1,2) Operating Temperature Range Storage Temperature Range W IC C D T ,. L O N KBPC KBPC KBPC KBPC KBPC KBPC KBPC 15005W 1501W 1502W 1504W 1506W 1508W 1510W VRRM VRMS VDC Volts Volts Volts I(AV) Amps IFSM Amps 2 2 It VF IR VISO R TJ TSTG As Volts 2.0 (-65 to +150) (-65 to +150) A mA VAC /W 1. Unit mounted on 5" X 4" X 3" (12.8cm X 10.2cm X 7.3cm)Al. finned Plate. 2. Bolt down on heat-sink with silicon thermal compound between bridge and mounting sutfae for maximum heat transfer efficiency with # 10 screw. WEJ ELECTRONIC CO. UNIT MB1505W MB151W MB152W MB154W MB156W MB158W MB1510W Http:// www.wej.cn E-mail:[email protected] RoHS MB1505W-1510W FIG.1-DERATING CURVE FOR FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER ELEMENT OUTPUT RECTIFIED CURREN6T AVERAGE FORWARD OUTPUT 15 Heat Sink Mounting Single Phase Half Wave 60Hz 5.0 Inductive or Resistive Load CURRENT, (A) CURRENT,(A) AL.Finned Plate 10 300 PEAK FORWARD SURGE 5" X 4" X 3" Thick (12.8 X 10.2 X 7.3cm) 200 100 1 Cycle 0 0 50 55 25 75 125 100 175 150 0 1 NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL FORWARD CHARACTERISTICS R T Tj =25 ° C Pulse Width=300uS 1%Duty Cycle 0.1 C E L 1.0 0.8 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE,(V) 1.8 10 (uA) O INSTANTANEOUS REVERSE CURRENT, 1.0 Tj =100 ° C N 10 (A) IC 100 0.6 CHARACTERISTICS PER BRIDGE ELEMENT 100 INSTANTANEOUS FORWARD CURRENT, C FIG.4-TYPICAL REVERSE PER BRIDGE ELEMENT 0.4 j max 100 10 CASE TEMPERATURE, ( ° C) 0.01 D T ,. L O 8.3ms Single Half Sine-Wave Tj (JEDEC Method) =T 1.0 Tj =25 ° C 0.1 0.01 60 40 20 0 120 100 80 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) E FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-MAXIMUM POWER DISSIPATION PER BRIDGE ELEMENT W 100 T j=25 ° C f=1MHz V sig =50mV p-p 10 0.1 1.0 10 100 REVRESE VOLTAGE,(V) WEJ ELECTRONIC CO. Http:// www.wej.cn 80 (W) JUNCTION CAPACITANCE,(pF) J E 100 AVERAGE POWER DISSIPATION OF BRIDGE, 1000 Tj =T j max 60 Capacitive Load 40 Resistive or Inductive 20 Load 0 0 5 10 15 20 25 30 35 AVERAGE OUTPUT CURRENT, (A) E-mail:[email protected]