IS31BL3228A/B WHITE LED DRIVER January 2014 GENERAL DESCRIPTION FEATURES The IS31BL3228A (IS31BL3228B) is a low noise, constant frequency charge pump DC/DC converter for white LED applications. The IS31BL3228A (IS31BL3228B) is capable of driving up to four (six) channels of LEDs at preset 20mA per channel from a 2.8V to 5.5V input. The current sinks may be operated individually or in parallel for driving higher current LEDs. Only one 1μF small capacitor (at C+ thru C-) and two small 2.2μF capacitors (at VCC and VOUT) are needed, it makes this part ideally suited for small, battery-powered applications. The serial digital input is used to enable, disable, and set current for each LED with 14 settings down to 1.8mA. Each output of the IS31BL3228A/IS31BL3228B is equipped with built-in soft-start circuitry prevents excessive inrush current during start-up. A low-current shutdown feature disconnects the load from the input and reduces quiescent current to less than 3μA. VCC range: 2.8V to 5.5V Fully programmable current with single wire 14 current levels Drives up to four (IS31BL3228A)/six (IS31BL3228B) channels of LEDs No inductors, low noise operation Built-in thermal protection Automatic soft start Low shutdown current: ISD <3μA UTQFN-12 (2mm × 2mm ) package APPLICATIONS Cell phone, smart phone, PDA MP3, MP4, PMP White LED backlighting The IS31BL3228A and IS31BL3228B are available in a Pb-free, space-saving 2mm × 2mm UTQFN-12 package. TYPICAL APPLICATION CIRCUIT Figure 1 Typical Application Circuit (IS31BL3228A) Note: COUT can’t be less than 2.2μF, and when less than six channels are used, keep the unused pin to GND or floating. But channel D0 (Pin 1) has to be used. Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 1 IS31BL3228A/B VBattery 3 VCC CIN 2.2 F C+ 1 F 9 D4 GND Figure 2 8 D5 Typical Application Circuit (IS31BL3228B) VBattery 3 CIN 2.2 F VCC VOUT D0 C+ IS31BL3228A 1 F 5 6 D1 C- D2 EN/SET N<=14 7 Figure 3 D3 GND 1 12 11 10 Application Circuit for Less Than 4 LEDs (IS31BL3228A) VBattery 3 CIN 2.2 F 4 VCC 5 6 C+ C- EN/SET D1 D2 D3 D4 GND 2 COUT 2.2 F IS31BL3228A N<=14 7 VOUT D0 1 F Figure 4 2 COUT 2.2 F 4 2 10 D3 EN/SET 7 1 11 D2 N<=14 2 12 D1 C- 6 1 1 IS31BL3228B 5 2 COUT 2.2 F D0 4 1 2 VOUT D5 1 12 11 10 9 8 Application Circuit for Less Than 6 LEDs (IS31BL3228B) Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 2 IS31BL3228A/B PIN CONFIGURATION Package Pin Configuration (Top View) UTQFN-12 IS31BL3228A UTQFN-12 IS31BL3228B PIN DESCRIPTION No. IS31BL3228A IS31BL3228B Description White LED channel, channel D0 must be used. Charge pump output to drive load circuits, requires 2.2μF capacitor connected between this pin and ground pin. 1 D0 D0 2 VOUT VOUT 3 VCC VCC 4 C+ C+ Flying capacitor positive terminal. 5 C- C- Flying capacitor negative terminal. 6 EN/SET EN/SET 7 GND GND NC - - D5, D4 White LED channel 5 and channel 4. D3~D1 D3~D1 White LED channel 3~1. 8, 9 10~12 Power supply input, requires 2.2μF capacitor connect between this pin and ground pin. Serial digital input, control the output current. Ground. No connection. Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 3 IS31BL3228A/B ORDERING INFORMATION Industrial Range: -40°C to +85°C Order Part No. IS31BL3228A-UTLS2-TR IS31BL3228B-UTLS2-TR Package QTY/Reel UTQFN-12, Lead-free 3000 Copyright © 2014 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 4 IS31BL3228A/B ABSOLUTE MAXIMUM RATINGS Supply voltage, VCC Voltage at any input pin Maximum junction temperature, TJMAX Storage temperature range, TSTG Operating temperature range, TA ESD (HBM) ESD (CDM) -0.3V ~ +6.0V -0.3V ~ VCC+0.3V 150°C -65°C ~ +150°C −40°C ~ +85°C 1kV 1kV Note: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other condition beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS CIN = COUT =2.2μF, TA = +25°C, unless otherwise noted. Typical value are TA = 25°C, VCC = 3.6V. Symbol Parameter Condition Min. Typ. Max. Unit 5.5 V Input Power Supply VCC Operation range ICC Operating current 2.8 ≤ VCC ≤ 5.5, ISET = 20mA charge pump disable 0.5 1 mA ISD Shutdown current VEN/SET = 0V 0.5 3 μA IDX ISINK average current accuracy ISET = 20mA 20 mA Current matching ISET = 20mA ±0.9 % 210 mV I(D-Match) VTH 2.8 Transition threshold at any ISINK pin Charge Pump Section TSS Soft-start time (Note 1) 33 μs fCLK Clock frequency (Note 1) 1 MHz VEN(L) Enable threshold low VCC = 2.8V VEN(H) Enable threshold high VCC = 5.5V EN/SET tEN/SET LO EN/SET low time 0.4 1.4 V 0.3 tEN/SET_HI_MIN Minimum EN/SET high time V 75 50 tEN/SET_HI_MAX Maximum EN/SET high time μs ns 75 μs tOFF EN/SET off timeout (Note 1) 500 μs tLAT EN/SET latch timeout (Note 1) 500 μs REN/SET DOWN EN/SET pull down resistor 500 kΩ Note 1: Guaranteed by design. Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 5 IS31BL3228A/B TYPICAL PERFORMANCE CHARACTERISTIC LED Current vs. Supply Voltage (IS31BL3228A) Figure 6 22 560 21 540 520 20 LED Current vs. Supply Voltage (IS31BL3228B) Charge Pump Disable ISET = 20mA 500 19 480 18 460 17 ICC IDX - LED Current (mA) Figure 5 16 440 420 15 -40 -15 Figure 7 10 35 60 85 LED Current vs. Temperature 400 2.5 3 Figure 8 3.5 4 4.5 5 5.5 ICC vs. Supply Voltage 1.4 1.2 1 0.8 0.6 ISD 0.4 0.2 0 2.5 3 3.5 Figure 9 4 4.5 5 5.5 ISD vs. Supply Voltage Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 6 IS31BL3228A/B FUNCTIONAL BLOCK DIAGRAM IS31BL3228A IS31BL3228B Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 7 IS31BL3228A/B APPLICATION INFORMATION GENERAL DESCRIPTION The IS31BL3228A (IS31BL3228B) charge pump drives up to four (six) white LEDs with regulated constant current for uniform intensity. It achieves 20mA output drive capability over the 1-cell lithium-battery input voltage range. Fixed-frequency switching of 1MHz allows for tiny external components, and the regulation scheme is optimized to ensure low EMI and low input ripple. CONSTANT CURRENT OUTPUT LEVEL SETTING The constant current source levels for D5/D3 to D0 are set via the serial interface according to a logarithmic scale. For the whole 14 codes, each code is approximately 1.5dB lower than the previous code. In this manner, LED brightness appears linear with each increasing code count. Because the outputs D5/D3 to D0 are true independent constant current sources, the voltage observed on any single given output will be determined by the actual forward voltage (VF) for the LED being driven. Figure 10 FUNCTIONAL DESCRIPTION The four (six) constant current source outputs (D5/D3 to D0) can drive four (six) individual LEDs with a maximum current of 20mA each. The PCC wire serial interface enables the IS31BL3228A (IS31BL3228B) and sets the current source magnitudes. PCC wire Serial Interface Timing PCC WIRE SERIAL INTERFACE The current level magnitude is controlled by Pulse Count Control (PCC wire) serial interface. The interface records rising edges of the EN/SET pin and decodes them into 14 different states. The 14 current level settings available are indicated in Table 1. The PCC wire serial interface has flexible timing. Data can be clocked-in at speeds from 15kHz to above 1MHz. After data is submitted, EN/SET is held high to latch the data. Once EN/SET has been held in the logic high state for time tLAT, the programmed current becomes active and the internal data register is reset to zero. For subsequent current level programming, the number of rising edges corresponding to the desired code must be entered on the EN/SET pin. Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 Since the output current sources of the IS31BL3228A (IS31BL3228B) are programmable, no PWM (pulse width modulation) or additional control circuitry is needed to control LED brightness. This feature greatly reduces the burden on a microcontroller or system IC to manage LED or display brightness, allowing the user to "set it and forget it." With its high-speed serial interface (1MHz data rate), the output current of the IS31BL3228A (IS31BL3228B) can be changed successively to brighten or dim LEDs, in smooth transitions (e.g., to fade-out) or in abrupt steps, giving the user complete programmability and real-time control of LED brightness. Table 1 Current Level Setting Data Output(mA/Ch) Data Output(mA/Ch) 1 20.0 8 6.0 2 17.0 9 5.0 3 14.0 10 4.2 4 12.0 11 3.6 5 10.0 12 3 6 8.6 13 2.4 7 7.0 14 1.8 8 IS31BL3228A/B PCC WIRE SERIAL INTERFACE TIMING CAPACITOR SELECTION Figure 10 shows the timing of PPC wire. When EN/SET is held low for an amount of time greater than tOFF, the IS31BL3228A (IS31BL3228B) enters into shutdown mode and draws less than 1µA from VCC. The internal data register is reset to zero during shutdown. When driving fewer than four (IS31BL3228A) (six for IS31BL3228B) LEDs, keep the unused pin to GND or floating, but D0 must be connected. Careful selection of the external capacitors (CIN and COUT) is important because they will affect turn-on time, output ripple, and transient performance. Optimum performance will be obtained when low equivalent series resistance (ESR) ceramic capacitors are used. In general, low ESR may be defined as less than 100mΩ. A value of 2.2µF for all three capacitors is a good starting point when choosing capacitors. If the LED current sources are programmed only for light current levels, then the capacitor size may be decreased. DEVICE SWITCHING NOISE PERFORMANCE CAPACITOR CHARACTERISTICS The IS31BL3228A (IS31BL3228B) operates at a fixed frequency of approximately 1MHz to control noise and limit harmonics that can interfere with the RF operation of cellular telephone handsets or other communication devices. Back-injected noise appearing on the input pin of the charge pump is 60mV peak-to-peak, typically ten times less than inductor-based DC/DC boost converter white LED backlight solutions. The IS31BL3228A (IS31BL3228B) soft-start feature prevents noise transient effects associated with inrush currents during start-up of the charge pump circuit. Ceramic composition capacitors are highly recommended over all other types of capacitors for use with the IS31BL3228A (IS31BL3228B). Ceramic capacitors offer many advantages over their tantalum and aluminum electrolytic counterparts. A ceramic capacitor typically has very low ESR, is lowest cost, has a smaller PCB footprint, and is non-polarized. Low ESR ceramic capacitors help to maximize charge pump transient response. Since ceramic capacitors are non-polarized, they are not prone to incorrect connection damage. THERMAL PROTECTION EQUIVALENT SERIES RESISTANCE The IS31BL3228A (IS31BL3228B) has a thermal protection circuit that will shut down the chip if the die temperature rises above the thermal limit. ESR is an important characteristic to consider when selecting a capacitor. ESR is a resistance internal to a capacitor that is caused by the leads, internal connections, size or area, material composition, and ambient temperature. Capacitor ESR is typically measured in milliohms for ceramic capacitors and can range to more than several ohms for tantalum or aluminum electrolytic capacitors. DRIVE FEWER LEDS Although the IS31BL3228A (IS31BL3228B) is designed for driving white LEDs, the device also can be used to drive most types of LEDs with forward voltage specifications ranging from 1.8V to 4.7V. LED applications may include main and sub-LCD display backlighting, camera photo-flash applications, color (RGB) LEDs, infrared (IR) diodes for remotes, and other loads benefiting from a controlled output current generated from a varying input voltage. Since the D5/D3 to D0 output current sources are matched with negligible voltage dependence, the LED brightness will be matched regardless of the specific LED forward voltage (VF) levels. In some instances (e.g., in high luminous output applications such as photo flash), it may be necessary to drive high-VF type LEDs. The low dropout current sources in the IS31BL3228A (IS31BL3228B) make it capable of driving LEDs with forward voltages as high as 4.7V at full current from an input supply of 2.8V to 5.5V. Outputs can be paralleled to drive high-current LEDs without complication Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 CERAMIC CAPACITOR MATERIALS Ceramic capacitors less than 0.1µF are typically made from NPO or C0G materials. NPO and C0G materials generally have tight tolerance and are very stable over temperature. Larger capacitor values are usually composed of X7R, X5R, Z5U, or Y5V dielectric materials. Large ceramic capacitors (i.e., greater than 2.2µF) are often available in low-cost Y5V and Z5U dielectrics. Capacitor area is another contributor to ESR. Capacitors that are physically large will have a lower ESR when compared to an equivalent material smaller capacitor. These larger devices can improve circuit transient response when compared to an equal value capacitor in a smaller package size. 9 IS31BL3228A/B CLASSIFICATION REFLOW PROFILES Profile Feature Pb-Free Assembly Preheat & Soak Temperature min (Tsmin) Temperature max (Tsmax) Time (Tsmin to Tsmax) (ts) 150°C 200°C 60-120 seconds Average ramp-up rate (Tsmax to Tp) 3°C/second max. Liquidous temperature (TL) Time at liquidous (tL) 217°C 60-150 seconds Peak package body temperature (Tp)* Max 260°C Time (tp)** within 5°C of the specified classification temperature (Tc) Max 30 seconds Average ramp-down rate (Tp to Tsmax) 6°C/second max. Time 25°C to peak temperature 8 minutes max. Figure 11 Classification profile Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 10 IS31BL3228A/B PACKAGE INFORMATION UTQFN-12 Note: All dimensions in millimeters unless otherwise stated. Integrated Silicon Solution, Inc. – www.issi.com Rev. B, 12/31/2013 11