INTEGRATED CIRCUITS 74F805, 74F1805 Hex 2-input NOR drivers Product specification IC15 Data Handbook 1990 Sep 14 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805/74F1805 FEATURES PIN CONFIGURATION • High capacitive drive capability • Choice of configuration 74F805 Corner VCC and GND – 74F805 Center VCC and GND – 74F1805 • Typical propagation delay of 2.3ns D0a 1 20 VCC D0b 2 19 D5b Q0 3 18 D5a D1a 4 17 Q5 D1b 5 16 D4b Q1 6 15 D4a D2a 7 14 Q4 TYPE TYPICAL PROPAGATION DELAY TYPICAL SUPPLY CURRENT ( TOTAL) 74F805 2.3ns 10mA D2b 8 13 D3b 10mA Q2 9 12 D3a GND 10 11 Q3 74F1805 2.3ns ORDERING INFORMATION ORDER CODE DESCRIPTION SF00456 COMMERCIAL RANGE VCC = 5V ±10%, Tamb = 0°C to +70°C PKG DWG # 20–pin plastic DIP N74F805N, N74F1805N SOT146-1 20–pin plastic SOL N74F805D, N74F1805D SOT163-1 LOGIC SYMBOL 74F805 1 2 4 5 7 8 12 13 15 16 18 19 INPUT AND OUTPUT LOADING AND FAN OUT TABLE PINS Dna – Dnb DESCRIPTION Data inputs D0a D0bD1a D1b D2a D2b D3aD3b D4aD4bD5a D5b 74F (U.L.) HIGH/ LOW LOAD VALUE HIGH/LOW 1.0/0.033 20µA/20µA Q0 Q1 Q2 Q3 Q4 Q5 Q0 – Q5 Data outputs 2400/80 48mA/48mA NOTE: One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state. 3 6 9 11 VCC = Pin 20 GND = Pin 10 14 17 SF00457 IEC/IEEE SYMBOL 74F805 1 2 1 3 4 5 6 7 8 9 12 13 11 15 16 14 18 19 17 SF00458 September 14, 1990 2 853-0037 00417 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805/74F1805 PIN CONFIGURATION LOGIC DIAGRAM 74F1805 74F1805 74F805 D4b 1 20 D4a Q5 2 19 Q4 D5a 3 18 D3b D5b 4 17 D3a VCC 5 16 Q3 1 D0a D0b 4 D1a D1b D0a 6 15 GND D0b 7 14 Q2 Q0 8 13 D2b D1a 9 12 D2a D1b 10 11 Q1 6 5 7 D2a D2b 9 8 12 D3a D3b 11 13 15 D4a D4b 14 16 18 D5a D5b SF00459 3 2 17 19 QO D0a D0b Q1 D1a D1b Q2 D2a D2b Q3 D3a D3b Q4 D4a D4b Q5 D5a D5b 6 9 12 17 10 12 13 17 18 20 1 3 20 INPUTS Dna D0a D0bD1a D1b D2a D2b D3a D3bD4a D4bD5a D5b 3 Q0 Q1 Q2 Q3 Q4 Q5 VCC = Pin 5 GND = Pin 15 8 11 14 16 19 VCC = Pin 5 GND = Pin 15 2 SF00460 IEC/IEEE SYMBOL 74F1805 6 7 1 8 9 10 11 12 13 14 17 18 16 20 1 19 3 4 2 SF00461 September 14, 1990 3 Qn H X L X H L L L H Notes to function table H = High voltage level L = Low voltage level X = Don’t care 2 4 OUTPUT Dnb 19 1 FUNCTION TABLE 4 16 18 74F1805 9 14 13 LOGIC SYMBOL 7 11 10 VCC = Pin 20 GND = Pin 10 6 8 7 QO Q1 Q2 Q3 Q4 Q5 SF00462 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805/74F1805 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free air temperature range.) SYMBOL PARAMETER RATING UNIT VCC Supply voltage –0.5 to +7.0 V VIN Input voltage –0.5 to +7.0 V IIN Input current –30 to +5 mA VOUT Voltage applied to output in high output state –0.5 to VCC V IOUT Current applied to output in low output state 96 mA Tamb Operating free air temperature range 0 to +70 Tstg Storage temperature range °C °C –65 to +150 RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER UNIT MIN NOM MAX 5.0 5.5 VCC Supply voltage 4.5 VIH High–level input voltage 2.0 VIL Low–level input voltage 0.8 V IIk Input clamp current –18 mA IOH High–level output current –48 mA IOL Low–level output current 48 mA +70 °C Tamb Operating free air temperature range V V 0 DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL TEST CONDITIONS1 PARAMETER LIMITS MIN VOH VOL High-level output voltage Low-level output voltage TYP2 UNIT MAX VCC = MIN, VIL = MAX ±10%VCC 2.0 V VIH = MIN, IOH = MAX ±5%VCC 2.0 V VCC = MIN, VIL = MAX ±10%VCC 0.38 0.55 V VIH = MIN, IOl = MAX ±5%VCC 0.38 0.55 V -0.73 -1.2 V VIK Input clamp voltage VCC = MIN, II = IIK II Input current at maximum input voltage VCC = MAX, VI = 7.0V 100 µA IIH High–level input current VCC = MAX, VI = 2.7V 20 µA IIL Low–level input current VCC = MAX, VI = 0.5V IO Output current3 VCC = MAX ICC Supply current (total) ICCH -60 VCC = MAX ICCL -20 µA -150 mA mA VIN = GND 3.0 5.0 VIN = 4.5V 17 25 mA NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25°C. 3. The output conditions have been chosen to produce a current that closely approximates one half of the true short–circuit output current, IOS. September 14, 1990 4 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805/74F1805 AC ELECTRICAL CHARACTERISTICS LIMITS Tamb = +25°C SYMBOL tPLH tPHL PARAMETER TEST CONDITION Propagation delay Dna, Dnb to Qn Tamb = 0°C to +70°C VCC = +5.0V ± 10% CL = 50pF, RL = 500Ω VCC = +5.0V CL = 50pF, RL = 500Ω Waveform 1 UNIT MIN TYP MAX MIN MAX 1.0 1.0 2.0 2.5 4.0 4.5 1.0 1.0 4.0 4.5 ns 1.5 ns tsk(o) Output skew1,2 Waveform 2 1.5 NOTES: 1. [tPN actual – tPM actual] for any output compared to any other output where N and M are either LH or HL. 2. Skew times are valid only under same test conditions (temperature, VCC, loading, etc.,). AC WAVEFORMS Dna, Dnb VM Qn VM tPHL tsk(0) tPLH VM Qn VM Qn VM VM SF00005 SF00455 Waveform 1. Propagation delay for inverting output Waveform 2. Output skew NOTE: For all waveforms, VM = 1.5V. TEST CIRCUIT AND WAVEFORMS VCC VIN tw 90% NEGATIVE PULSE VM D.U.T. RT CL RL AMP (V) VM 10% VOUT PULSE GENERATOR 90% 10% tTHL (tf ) tTLH (tr ) tTLH (tr ) tTHL (tf ) 0V AMP (V) 90% 90% POSITIVE PULSE DEFINITIONS: RL = Load resistor; see AC ELECTRICAL CHARACTERISTICS for value. CL = Load capacitance includes jig and probe capacitance; see AC ELECTRICAL CHARACTERISTICS for value. RT = Termination resistance should be equal to ZOUT of pulse generators. VM VM 10% Test Circuit for Totem-Pole Outputs 10% tw 0V Input Pulse Definition INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate tw tTLH tTHL 1MHz 500ns 2.5ns 2.5ns SF00006 September 14, 1990 5 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805, 74F1805 DIP20: plastic dual in-line package; 20 leads (300 mil) 1990 Sep 14 6 SOT146-1 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805, 74F1805 SO20: plastic small outline package; 20 leads; body width 7.5 mm 1990 Sep 14 7 SOT163-1 Philips Semiconductors Product specification Hex 2-input NOR drivers 74F805, 74F1805 Data sheet status Data sheet status Product status Definition [1] Objective specification Development This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. Preliminary specification Qualification This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. Product specification Production This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Copyright Philips Electronics North America Corporation 1999 All rights reserved. Printed in U.S.A. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088–3409 Telephone 800-234-7381 print code Document order number: 1990 Sep 14 8 Date of release: 04-99 9397-750-05718