IS62/65WV2568DALL IS62/65WV2568DBLL 256K x 8 LOW VOLTAGE, FEBRUARY 2012 ULTRA LOW POWER CMOS STATIC RAM FEATURES • High-speed access time: 35ns, 45ns, 55ns DESCRIPTION The ISSI IS62/65WV2568DALL and IS62/65WV2568DBLL are high-speed, 2M bit static RAMs organized as 256K words by 8 bits. It is fabricated using ISSI's highperformance CMOS technology.This highly reliable process coupled with innovative circuit design techniques, yields high-performance and low power consumption devices. • CMOS low power operation – 36 mW (typical) operating – 9 µW (typical) CMOS standby • TTL compatible interface levels • Single power supply – 1.8V ± 10% Vcc (IS62/65WV2568DALL) – 2.5V–3.6V Vcc (IS62/65WV2568DBLL) • Fully static operation: no clock or refresh required • Three state outputs When CS1 is HIGH (deselected) or when CS2 is low (deselected) , the device assumes a standby mode at which the power dissipation can be reduced down with CMOS input levels. Easy memory expansion is provided by using Chip Enable and Output Enable inputs. The active LOW Write Enable (WE) controls both writing and reading of the memory. The IS62/65WV2568DALL and IS62/65WV2568DBLL are packaged in the JEDEC standard 32-pin TSOP (TYPE I), sTSOP (TYPE I), and 36-pin mini BGA. • Industrial temperature available • Lead-free available FUNCTIONAL BLOCK DIAGRAM A0-A17 DECODER 256K x 8 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VCC GND I/O0-I/O7 CS2 CS1 OE CONTROL CIRCUIT WE Copyright © 2012 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without notice. ISSI assumes no liability arising out of the application or use of any information, products or services described herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and before placing orders for products. Integrated Silicon Solution, Inc. does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless Integrated Silicon Solution, Inc. receives written assurance to its satisfaction, that: a.) the risk of injury or damage has been minimized; b.) the user assume all such risks; and c.) potential liability of Integrated Silicon Solution, Inc is adequately protected under the circumstances Integrated Silicon Solution, Inc. — www.issi.com — 1-800-379-4774 Rev. A 02/09/2012 1 IS62/65WV2568DALL, IS62/65WV2568DBLL PIN DESCRIPTIONS A0-A17 Address Inputs CS1 Chip Enable 1 Input CS2 Chip Enable 2 Input OE Output Enable Input WE Write Enable Input I/O0-I/O7 Input/Output NC No Connection Vcc Power GND Ground PIN CONFIGURATION 36-pin mini BGA (B) (6mm x 8mm) 1 2 2 3 4 5 32-pin TSOP (TYPE I), sTSOP (TYPE I) 6 A A0 A1 CS2 A3 A6 A8 B I/O4 A2 WE A4 A7 I/O0 C I/O5 NC A5 D GND Vcc E Vcc GND F I/O6 G I/O7 H A9 I/O1 NC A17 I/O2 OE CS1 A16 A15 I/O3 A10 A11 A12 A13 A14 A11 A9 A8 A13 WE CS2 A15 VCC A17 A16 A14 A12 A7 A6 A5 A4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 OE A10 CS1 I/O7 I/O6 I/O5 I/O4 I/O3 GND I/O2 I/O1 I/O0 A0 A1 A2 A3 Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 IS62/65WV2568DALL, IS62/65WV2568DBLL ABSOLUTE MAXIMUM RATINGS(1) Symbol Vterm Tstg Pt Parameter Terminal Voltage with Respect to GND Storage Temperature Power Dissipation Value –0.2 to Vcc+0.3 –65 to +150 1.0 Unit V °C W Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING RANGE (Vcc) Range Ambient Temperature Commercial 0°C to +70°C Industrial –40°C to +85°C Automotive (A3) –40°C to +125°C IS62/65WV2568DALL 1.8V ± 10% 1.8V ± 10% 1.8V ± 10% IS62/65WV2568DBLL 2.5V - 3.6V 2.5V - 3.6V 2.5V - 3.6V DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol Voh Parameter Output HIGH Voltage Vol Output LOW Voltage Test Conditions Ioh = -0.1 mA Ioh = -1 mA Iol = 0.1 mA Iol = 2.1 mA Vih Input HIGH Voltage Vil(1) Input LOW Voltage Ili Ilo Input Leakage Output Leakage Vcc 1.8V ± 10% 2.5-3.6V 1.8V ± 10% 2.5-3.6V 1.8V ± 10% 2.5-3.6V 1.8V ± 10% 2.5-3.6V GND ≤ Vin ≤ Vcc GND ≤ Vout ≤ Vcc, Outputs Disabled Min. 1.4 2.2 — — 1.4 2.2 –0.2 –0.2 –1 –1 Max. — — 0.2 0.4 Vcc + 0.2 Vcc + 0.3 0.4 0.6 1 1 Unit V V V V V V V V µA µA Notes: For IS62/65WV2568DALL: Vil (min.) = -1.0V AC (pluse width < 10ns). Not 100% tested. Vih (max.) = Vcc + 1.0V AC; (pluse width < 10ns). Not 100% tested. For IS62/65WV2568DBLL: Vil (min.) = -2.0V AC (pluse width < 10ns). Not 100% tested. Vih (max.) = Vcc + 2.0V AC; (pluse width < 10ns). Not 100% tested. Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 3 IS62/65WV2568DALL, IS62/65WV2568DBLL CAPACITANCE(1) Symbol Cin Cout Parameter Input Capacitance Input/Output Capacitance Conditions Vin = 0V Vout = 0V Max. 8 10 Unit pF pF Note: 1. Tested initially and after any design or process changes that may affect these parameters. AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load R1(Ω) R2(Ω) Vref Vtm 62WV2568DALL (Unit) 0.4V to Vcc-0.2V 5 ns 1.8V ± 10% 3070 3150 0.9V 1.8V 62WV2568DBLL (Unit) 0.4V to Vcc-0.3V 5ns Vref Vref See Figures 1 and 2 See Figures 1 and 2 2.5V - 3.6V 3070 3150 1.5V 2.8V AC TEST LOADS R1 R1 VTM VTM OUTPUT OUTPUT 30 pF Including jig and scope Figure 1 4 5 pF Including jig and scope R2 R2 Figure 2 Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 IS62/65WV2568DALL, IS62/65WV2568DBLL POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) Symbol Parameter Test Conditions Icc Vcc Dynamic Operating Vcc = Max., Com. Supply Current Iout = 0 mA, f = fmax Ind. Auto. typ.(2) Isb1 TTL Standby Current Vcc = Max., Com. (TTL Inputs) Vin = Vih or Vil Ind. CS1 = Vih , CS2 = Vil, Auto. f = 1 MHz Isb2 CMOS Standby Current (CMOS Inputs) Vcc = Max., CS1 ≥ Vcc – 0.2V, CS2 ≤ 0.2V, Vin ≥ Vcc – 0.2V, or Vin ≤ 0.2V, f = 0 Com. Ind. Auto. typ.(2) Max. 35ns 15 20 25 10 0.1 0.1 0.2 Max. 45ns 12 15 20 8 0.1 0.1 0.2 Max. 55ns 10 12 15 6 0.1 0.1 0.2 Unit 7 10 – 7 10 18 3 7 10 18 µA mA mA Note: 1. At f = fmax, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. 2. Typical values are measured at Vcc = 3.0V, Ta = 25oC and not 100% tested. Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 5 IS62/65WV2568DALL, IS62/65WV2568DBLL READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) 35ns 45ns 55ns Symbol Parameter Min. Max. Min. Max. Min. Max. Unit trc Read Cycle Time 35 — 45 — 55 — ns taa Address Access Time — 35 — 45 — 55 ns toha Output Hold Time 10 — 10 — 10 — ns tacs1/tacs2 CS1/CS2 Access Time — 35 — 45 — 55 ns tdoe OE Access Time — 15 — 20 — 25 ns thzoe(2) OE to High-Z Output — 10 — 15 — 20 ns tlzoe(2) OE to Low-Z Output 5 — 5 — 5 — ns thzcs1/thzcs2(2) CS1/CS2 to High-Z Output 0 10 0 15 0 20 ns tlzcs1/tlzcs2 CS1/CS2 to Low-Z Output 10 — 10 — 10 — ns (2) Notes: 1. Test conditions and output loading conditions are specified in the AC Test Conditions and AC Test Loads (Figure 1). 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. AC WAVEFORMS READ CYCLE NO. 1(1,2) (Address Controlled) (CS1 = OE = Vil, CS2 = WE = Vih) tRC ADDRESS tAA tOHA DOUT 6 PREVIOUS DATA VALID tOHA DATA VALID Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 IS62/65WV2568DALL, IS62/65WV2568DBLL AC WAVEFORMS READ CYCLE NO. 2(1,3) (CS1, CS2, OE Controlled) tRC ADDRESS tAA tOHA OE tDOE CS1 tHZOE tLZOE tACS1/tACS2 CS2 DOUT tLZCS1/ tLZCS2 HIGH-Z tHZCS DATA VALID Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CS1= Vil. CS2=WE=Vih. 3. Address is valid prior to or coincident with CS1 LOW and CS2 HIGH transition. Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 7 IS62/65WV2568DALL, IS62/65WV2568DBLL WRITE CYCLE SWITCHING CHARACTERISTICS(1,2) (Over Operating Range) 35ns Symbol Parameter twc 45ns 55ns Min. Max. Min. Max. Min. Max. Unit Write Cycle Time 35 — 45 — 55 — ns tscs1/tscs2 CS1/CS2 to Write End 25 — 35 — 45 — ns taw Address Setup Time to Write End 25 — 35 — 45 — ns tha Address Hold from Write End 0 — 0 — 0 — ns tsa Addrress Setup Time 0 — 0 — 0 — ns tpwe WE Pulse Width 30 — 35 — 40 — ns tsd Data Setup to Write End 15 — 20 — 25 — ns thd Data Hold from Write End 0 — 0 — 0 — ns thzwe WE LOW to High-Z Output — 20 — 20 — 20 ns tlzwe WE HIGH to Low-Z Output 5 — 5 — 5 — ns Notes: 1. Test conditions and output loading conditions are specified in the AC Test Conditions and AC Test Loads (Figure 1). 2. The internal write time is defined by the overlap of CS1 LOW, CS2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. 3. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. AC WAVEFORMS WRITE CYCLE NO. 1 (CS1/CS2 Controlled, OE = HIGH or LOW) tWC ADDRESS tHA tSCS1 CS1 tSCS2 CS2 tAW tPWE WE tSA DOUT DATA UNDEFINED tHZWE tLZWE HIGH-Z tSD DIN 8 tHD DATA-IN VALID Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 IS62/65WV2568DALL, IS62/65WV2568DBLL AC WAVEFORMS WRITE CYCLE NO. 2 (WE Controlled: OE is HIGH During Write Cycle) tWC ADDRESS OE tHA tSCS1 CS1 tSCS2 CS2 tAW tPWE WE tSA DOUT tHZWE tLZWE HIGH-Z DATA UNDEFINED tSD DIN tHD DATA-IN VALID WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle) tWC ADDRESS OE tHA tSCS1 CS1 tSCS2 CS2 tAW tPWE WE tSA DOUT DATA UNDEFINED tHZWE tLZWE HIGH-Z tSD DIN Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 tHD DATA-IN VALID 9 IS62/65WV2568DALL, IS62/65WV2568DBLL DATA RETENTION SWITCHING CHARACTERISTICS Symbol Vdr Idr Parameter Vcc for Data Retention Data Retention Current tsdr trdr Data Retention Setup Time Recovery Time Test Condition Min. See Data Retention Waveform 1.5 Vcc = 1.5V, CS1 ≥ Vcc – 0.2V, Com. — CS2 ≤ 0.2V Ind. — Auto. — typ.(1) — See Data Retention Waveform 0 See Data Retention Waveform trc Max. 3.6 7 10 15 2 — — Unit V µA ns ns Note: 1. Typical values are measured at Vcc = Vdr(min), Ta = 25oC and not 100% tested. DATA RETENTION WAVEFORM (CS1 Controlled) Data Retention Mode tSDR 3.0V 2.2V tRDR VCC VDR CS1 ≥ VCC CS1 GND - 0.2V DATA RETENTION WAVEFORM (CS2 Controlled) Data Retention Mode 3.0 VCC CS2 2.2V tSDR tRDR VDR 0.4V CS2 ≤ 0.2V GND 10 Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 IS62/65WV2568DALL, IS62/65WV2568DBLL ORDERING INFORMATION IS62WV2568DALL (1.8 ± 10%) Industrial Range: –40°C to +85°C Speed (ns) 55 55 55 55 55 55 Order Part No. IS62WV2568DALL-55TI IS62WV2568DALL-55TLI IS62WV2568DALL-55BI IS62WV2568DALL-55BLI IS62WV2568DALL-55HI IS62WV2568DALL-55HLI Package TSOP, TYPE I TSOP, TYPE I, Lead-free mini BGA (6mm x 8mm) mini BGA (6mm x 8mm), Lead-free sTSOP, TYPE I sTSOP, TYPE I, Lead-free IS62WV2568DBLL (2.5V - 3.6V) Industrial Range: –40°C to +85°C Speed (ns) 35 35 45 45 45 45 45 45 Order Part No. IS62WV2568DBLL-35HLI IS62WV2568DBLL-35TLI IS62WV2568DBLL-45TI IS62WV2568DBLL-45TLI IS62WV2568DBLL-45BI IS62WV2568DBLL-45BLI IS62WV2568DBLL-45HI IS62WV2568DBLL-45HLI Package sTSOP, TYPE I TSOP, TYPE I, Lead-free TSOP, TYPE I TSOP, TYPE I, Lead-free mini BGA (6mm x 8mm) mini BGA (6mm x 8mm), Lead-free sTSOP, TYPE I sTSOP, TYPE I, Lead-free IS65WV2568DBLL (2.5V - 3.6V) Automotive Range (A3): –40°C to +125°C Speed (ns) 45 45 Order Part No. IS65WV2568DBLL-45TLA3 IS65WV2568DBLL-45HLA3 Package TSOP, TYPE I, Lead-free sTSOP, TYPE I, Lead-free Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 11 IS62/65WV2568DALL, IS62/65WV2568DBLL 12 Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 IS62/65WV2568DALL, IS62/65WV2568DBLL Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012 13 14 08/12/2008 Package Outline 1. CONTROLLING DIMENSION : MM . 2. Reference document : JEDEC MO-207 NOTE : IS62/65WV2568DALL, IS62/65WV2568DBLL Integrated Silicon Solution, Inc. — www.issi.com Rev. A 02/09/2012