MSIW1000 SERIES DC/DC CONVERTER 3W, SMD-Package FEATURES ►SMD Package with Industry Standard Pinout ►Package Dimension: 32.3 x 14.8 x 10.2 mm (1.27”x 0.58”x 0.38” inches) ►Wide 2:1 Input Range ►Efficiency up to 83% ►I/O-isolation 1500VDC ►Operating Temp. Range -40°C to +85°C ►Qualified for lead-free Reflow Solder Process according IPC/JEDEC J-STD-020D ►3 Years Product Warranty PRODUCT OVERVIEW The MINMAX MSIW1000 series is a range of isolated 3W DC/DC converter modules featuring fully regulated output voltages and wide 2:1 input voltage ranges. These products are in a low profile SMD package with dimensions of 32.3 x 14.8 x 10.2 mm. All models are qualified for lead free reflow solder processes according IPC J-STD-20D.An excellent efficiency allows an operating temperature range of–40° to +85°C (with derating). Typical applications for these converters are battery operated equipment and instrumentation, communication and general industrial electronics. Model Selection Guide Model Input Output Number Voltage Voltage (Range) VDC Output Current Input Current Reflected Max. capacitive Ripple Load Max. Min. @Max. Load @No Load Current mA(typ.) mA(typ.) Efficiency (typ.) @Max. Load VDC mA mA mA(typ.) MSIW1021 3.3 700 70 257 MSIW1022 5 600 60 316 12 250 25 305 15 200 20 305 ±5 ±300 ±30 321 MSIW1026 ±12 ±125 ±12.5 309 MSIW1027 ±15 ±100 ±10 309 81 MSIW1031 3.3 700 70 127 76 MSIW1023 MSIW1024 MSIW1025 12 (9 ~ 18) MSIW1032 5 600 60 156 MSIW1033 12 250 25 151 MSIW1034 24 (18 ~ 36) uF % 75 4700 20 25 79 82 82 78 180# 4700 5 15 81 80 83 15 200 20 151 ±5 ±300 ±30 158 MSIW1036 ±12 ±125 ±12.5 152 MSIW1037 ±15 ±100 ±10 152 82 MSIW1041 3.3 700 70 63 76 MSIW1042 5 600 60 78 MSIW1043 12 250 25 75 15 200 20 75 MSIW1035 MSIW1044 MSIW1045 48 (36 ~ 75) ±5 ±300 ±30 79 MSIW1046 ±12 ±125 ±12.5 76 MSIW1047 ±15 ±100 ±10 76 83 79 180# 4700 3 10 2012/01/10 REV:4 Tel:886-6-2923150 Page 1 of 4 80 83 83 79 180# 82 82 # For each output E-mail:[email protected] 82 MSIW1000 SERIES DC/DC CONVERTER 3W, SMD-Package Input Specifications Parameter Model 12V Input Models 24V Input Models 48V Input Models 12V Input Models 24V Input Models 48V Input Models 12V Input Models 24V Input Models 48V Input Models Input Surge Voltage (1 sec. max.) Start-Up Voltage Under Voltage Shutdown Reverse Polarity Input Current Short Circuit Input Power Input Filter Internal Power Dissipation All Models Min. -0.7 -0.7 -0.7 4.5 8 16 ----------- Typ. ------6 12 24 ----------- Max. 25 50 100 8 18 36 8 16 32 0.5 1500 Unit --- --- 2500 mW Min. --------- Typ. ±0.5 ±0.5 ±0.1 ±0.3 Max. ±1.0 ±2.0 ±0.3 ±1.0 ------------- 50 ----200 ±2 ±0.01 75 100 10 500 ±6 ±0.02 Unit % % % % mV P-P mV P-P mV rms uS % %/℃ VDC A mW Pi Filter Output Specifications Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple & Noise (20MHz) Ripple & Noise (20MHz) Ripple & Noise (20MHz) Transient Recovery Time Transient Response Deviation Temperature Coefficient Short Circuit Protection Conditions Dual Output, Balanced Loads Vin=Min. to Max. Io=10% to 100% Over Line, Load & Temp. 25% Load Step Change Continuous General Specifications Parameter I/O Isolation Voltage (rated) I/O Isolation Resistance I/O Isolation Capacitance Switching Frequency MTBF (calculated) Moisture Sensitivity Level (MSL) Safety Approvals Conditions 60 Seconds 500 VDC 100KHz, 1V Min. 1500 1000 ----1,000,000 Typ. ----65 300 --- Max. ----100 ----- Unit VDC MΩ pF KHz Hours MIL-HDBK-217F@25℃, Ground Benign IPC/JEDEC J-STD-020D Level 2 UL/cUL 60950-1 recognition(CSA certificate), IEC/EN 60950-1(CB-scheme) Input Fuse 12V Input Models 750mA Slow-Blow Type 24V Input Models 350mA Slow-Blow Type 48V Input Models 200mA Slow-Blow Type Environmental Specifications Parameter Operating Temperature Range (with Derating) Case Temperature Storage Temperature Range Humidity (non condensing) Cooling Lead Temperature (1.5mm from case for 10Sec.) E-mail:[email protected] 2012/01/10 REV:4 Tel:886-6-2923150 Page 2 of 4 Conditions Ambient Min. -40 ---50 --Free-Air convection --- Max. +85 +90 +125 95 Unit ℃ ℃ ℃ % rel. H 260 ℃ MSIW1000 SERIES DC/DC CONVERTER 3W, SMD-Package Power Derating Curve Notes 1 Specifications typical at Ta=+25℃, resistive load, nominal input voltage and rated output current unless otherwise noted. 2 Transient recovery time is measured to within 1% error band for a step change in output load of 75% to 100% 3 Ripple & Noise measurement bandwidth is 0-20MHz. 4 These power converters require a minimum output loading to maintain specified regulation, operation under no-load conditions will not damage these modules; 5 All DC/DC converters should be externally fused at the front end for protection. however they may not meet all specifications listed. 6 Other input and output voltage may be available, please contact factory. 7 That “natural convection” is about 20LFM but is not equal to still air (0 LFM). 8 Specifications subject to change without notice. 9 It is not recommended to use water-washing process on SMT units. Package Specifications Mechanical Dimensions Connecting Pin Patterns 32.3 [1.27] 5.08 [0.2] 24 23 22 15 14 13 27.94 [1.10] 2.6 [0.10] 18.8 [0.74] [0.2] 16.1 [0.63] 17.78 [0.7] 5.08 14.8 [0.58] 2.18 [0.09] 20.0 [0.79] 10 11 12 1 2 3 9.7 [0.38] 0.50 [0.02] 2.54 [0.10] ►All 5 (X.XX±0.01) 0~ X.XX±0.13 ( X.XXX±0.005) 0.15 S ►Pins Pin Connections 1.0 [0.04] dimensions in mm (inches) ►Tolerance: X.X±0.25 10.2 0.5 [0.4 0.02] 0.5 [0.02] S SEATING PLANE 17.78 [0.70] ±0.05 (±0.002) Physical Characteristics Pin Single Output Dual Output 1,2 -Vin -Vin 3,11,14,22 NC NC 10 NC Common 12 NC -Vout 13 +Vout +Vout 15 -Vout Common 23,24 +Vin +Vin NC : No Connection E-mail:[email protected] 2012/01/10 REV:4 Tel:886-6-2923150 Page 3 of 4 Case Size : 32.3x14.8x10.2mm (1.27x0.58x0.4 Inches) Case Material : Non-Conductive Black Plastic (flammability to UL 94V-0 rated) Weight : 8.8g MSIW1000 SERIES DC/DC CONVERTER 3W, SMD-Package Test Configurations Input Reflected-Ripple Current Test Setup Input reflected-ripple current is measured with a inductor Lin (4.7uH) and Cin (220uF, ESR < 1.0Ω at 100 KHz) to simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple is measured at the input terminals of the module, measurement bandwidth is 0-500 KHz. To Oscilloscope + + Battery +Vin Lin DC / DC Converter Current Probe Cin +Out -Vin Load -Out Peak-to-Peak Output Noise Measurement Test Use a Cout 0.47uF ceramic capacitor. Scope measurement should be made by using a BNC socket, measurement bandwidth is 0-20 MHz. Position the load between 50 mm and 75 mm from the DC/DC Converter. +Vin +Out Copper Strip Single Output DC / DC Converter -Vin Cout -Out Scope Resistive Load Copper Strip +Vin +Out Copper Strip Dual Output DC / DC Converter Com. Copper Strip -Vin -Out Scope Cout Resistive Load Cout Scope Copper Strip Design & Feature Considerations Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. The unit operates normally once the output current is brought back into its specified range. Input Source Impedance The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the power module. In applications where power is supplied over long lines and output loading is high, it may be necessary to use a capacitor at the input to ensure startup. Capacitor mounted close to the power module helps ensure stability of the unit, it is recommended to use a good quality low Equivalent Series Resistance (ESR < 1.0Ω at 100 KHz) capacitor of a 3.3uF for the 12V input devices and a 1.5uF for the 24V and 48V devices. + DC Power Source +Vin + +Out DC / DC Converter Load Cin - -Vin -Out Output Ripple Reduction A good quality low ESR capacitor placed as close as practicable across the load will give the best ripple and noise performance. To reduce output ripple, it is recommended to use 3.3uF capacitors at the output. + +Vin DC Power Source - +Out Single Output DC / DC Converter -Vin + Cout Load -Out +Vin DC Power Source - +Out Dual Output DC / DC Com. Converter -Vin -Out Cout Load Load Cout Maximum Capacitive Load The MSIW1000 series has limitation of maximum connected capacitance at the output. The power module may be operated in current limiting mode during start-up, affecting the ramp-up and the startup time. For optimum performance we recommend 180uF maximum capacitive load for dual outputs and 4700uF capacitive load for single outputs. The maximum capacitance can be found in the data sheet. Thermal Considerations Many conditions affect the thermal performance of the power module, such as orientation, airflow over the module and board spacing. To avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90℃. The derating curves are determined from measurements obtained in a test setup. Position of air velocity probe and thermocouple 15mm / 0.6in 50mm / 2in Air Flow DUT 18, Sin Sin Road, An-Ping Industrial District, Tainan 702, Taiwan Tel: 886-6-2923150 Fax: 886-6-2923149 E-mail: [email protected] Minmax Technology Co., Ltd. 2012/01/10 REV:4 Page 4 of 4