MOTOROLA MC44030 Multistandard video signal processor with integrated chroma delay line Datasheet

Order this document from Analog Marketing
The MC44030/35 is a highly advanced circuit which performs most of the
basic functions required for a color TV. All its advanced features are under
processor control via I2C bus, enabling potentiometer controls to be
removed completely and allowing significant cost savings together with the
possibility of implementing sophisticated automatic test routines.
MULTISTANDARD
VIDEO SIGNAL PROCESSOR
WITH INTEGRATED
CHROMA DELAY LINE
SEMICONDUCTOR
TECHNICAL DATA
A summary of the features available on the device is given below:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Operation from a Single 5.0 V Supply; Low Current Consumption
(Typically 150 mA)
PAL/SECAM/NTSC Decoding Capability (4 Matrix Modes Available)
Integrated Chroma Delay Line
Dual Composite Video or S–VHS Inputs
Integrated Luma and Chroma Filters (Including SECAM Cloche Filter)
Programmable Luma Delay and Peaking
40
1
RGB Drives Including CONTRAST/BRIGHTNESS Controls and Auto
Grey–Scale
P SUFFIX
PLASTIC PACKAGE
CASE 711
External RGB and Fast Commutate Inputs with SATURATION Control
Possibility
Auxiliary Y, R–Y, B–Y Inputs
Line Timebase Featuring H–PHASE Control and Switchable Phase
Detector Gain
44
1
Countdown Type Vertical Timebase Including the Vertical Geometry
Corrections
FTB SUFFIX
PLASTIC PACKAGE
CASE 824D
(TQFP–44)
16:9 Display Mode Capability
E–W Parabola Drive Including the Horizontal Geometry Corrections
Anode Current Monitor with Vertical Breathing Compensation
Analog Contrast Control, Allowing Fast Beam Current Limitation
Pin to Pin Compatible with MC44002/7
MC44035 is the PAL/NTSC Only Version of the MC44030
Available in DIP and TQFP Packages
ORDERING INFORMATION
Device
Operating
Temperature Range
MC44030P
Plastic DIP
MC44030FTB
MC44035P
MC44035FTB
This document contains information on a product under development. Motorola reserves the
right
to change or discontinue
thisIC
product
without
notice.
MOTOROLA
ANALOG
DEVICE
DATA
 Motorola, Inc. 1996
Package
TQFP–44
TA = 0° to +70°C
Plastic DIP
TQFP–44
Issue 0
1
MC44030 MC44035
Simplified Block Diagram
R-Y
B-Y
Y1
37
36
29
Video 1
(S-VHS)
Video 2
2
31
40
Chroma
Take–Off
Filter
Input
Select
11
1
ACC
PAL/
NTSC/
SECAM
Decoders
Super
Sandcastle
Sync
Sep
38
System
Select
Chroma
Delay
Line
Ident
Hue
Control
Luma Delay
Peaking & Trap
17.7 MHz
Vert
Sync
Sep
33
Osc
32
Memory/Control Registers
V–Sync
39
Freq
Divider
Ramp
Gen
PLL 1
15
Beam
Current
Monitor
Control
Loops
Iref
Loop
2
14
34
Parab
Gen
35
12
13
H– Drive
H –Flyback
5.0 V
Pulse
RGB
Outputs
Rx/Tx
Flyback
Sense
D/A
7
3
V–Drive
6
8
9
E-W
Drive
5.0 V
4
5
20
Clk Data
Y2
27
R-Y
26
B-Y
21
Col Diff
Stage,
Matrix
Switching,
Sat Control
Clk
25
28
Y1
Clamp
14.3 MHz
NOTE:
Luma
Select
24
Fast Comm
Red
23
Green
22
10
Blue
Analog
Contrast
17
Red
18
Green
19
Blue
30
Analog
Output
16
Fdbck
Anode I2C Bus
Current
Pin numbers shown are for the DIP package.
This device contains 6360 active transistors.
2
MOTOROLA ANALOG IC DEVICE DATA
MC44030 MC44035
OUTLINE DIMENSIONS
P SUFFIX
PLASTIC PACKAGE
CASE 711–03
ISSUE C
40
NOTES:
1. POSITIONAL TOLERANCE OF LEADS (D), SHALL
BE WITHIN 0.25 (0.010) AT MAXIMUM MATERIAL
CONDITION, IN RELATION TO SEATING PLANE
AND EACH OTHER.
2. DIMENSION L TO CENTER OF LEADS WHEN
FORMED PARALLEL.
3. DIMENSION B DOES NOT INCLUDE MOLD FLASH.
21
B
1
20
L
A
C
N
J
H
G
F
D
K
SEATING
PLANE
M
DIM
A
B
C
D
F
G
H
J
K
L
M
N
MILLIMETERS
MIN
MAX
51.69
52.45
13.72
14.22
3.94
5.08
0.36
0.56
1.02
1.52
2.54 BSC
1.65
2.16
0.20
0.38
2.92
3.43
15.24 BSC
0_
15_
0.51
1.02
INCHES
MIN
MAX
2.035
2.065
0.540
0.560
0.155
0.200
0.014
0.022
0.040
0.060
0.100 BSC
0.065
0.085
0.008
0.015
0.115
0.135
0.600 BSC
0_
15_
0.020
0.040
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
MOTOROLA ANALOG IC DEVICE DATA
3
MC44030 MC44035
OUTLINE DIMENSIONS
FTB SUFFIX
PLASTIC PACKAGE
CASE 824D–01
(TQFP–44)
ISSUE O
L
–T–, –U–, –Z–
–Z–
44
34
11
T–U
22
G
AE
DETAIL AA
M
V
S
AE
F
PLATING
J
23
12
0.20 (0.008)
DETAIL AA
0.05 (0.002) Z
AC Z
S
T–U
0.20 (0.008)
M
B
L
S
–U–
AB Z
–T–
S
33
1
BASE METAL
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
N
D
0.20 (0.008)
A
0.20 (0.008)
AB T–U
M
Z
S
S
M
AC T–U
Z
S
S
M
C
DETAIL AD
–AB–
E
0.10 (0.004)
–AC–
H
Y
R
K
W
Q
X
VIEW AD
AC T–U
S
Z
S
SECTION AE–AE
S
0.05 (0.002) T–U
0.20 (0.008)
M
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE –AB– IS LOCATED AT BOTTOM OF LEAD AND
IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS
THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE.
4. DATUMS –T–, –U– AND –Z– TO BE DETERMINED AT DATUM
PLANE –AB–.
5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING
PLANE –AC–.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.25 (0.010)
PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD
MISMATCH AND ARE DETERMINED AT DATUM PLANE –AB–.
7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION.
DAMBAR PROTRUSION SHALL NOT CAUSE THE D
DIMENSION TO EXCEED 0.530 (0.021).
MILLIMETERS
DIM MIN
MAX
A
9.950 10.050
B
9.950 10.050
C
1.400
1.600
D
0.300
0.450
E
1.350
1.450
F
0.300
0.400
G
0.800 BSC
H
0.050
0.150
J
0.090
0.200
K
0.450
0.550
L
8.000 BSC
M
12_REF
N
0.090
0.160
Q
1_
5_
R
0.100
0.200
S 11.900 12.100
V 11.900 12.100
W
0.200 REF
X
1.000 REF
Y
12_REF
INCHES
MIN
MAX
0.392
0.396
0.392
0.396
0.055
0.063
0.012
0.018
0.053
0.057
0.012
0.016
0.031 BSC
0.002
0.006
0.004
0.008
0.018
0.022
0.315 BSC
12_REF
0.004
0.006
1_
5_
0.004
0.008
0.469
0.476
0.469
0.476
0.008 REF
0.039 REF
12_REF
How to reach us:
USA / EUROPE / Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
4
◊
MOTOROLA ANALOG IC DEVICE DATA
*MC44030/D*
MC44030/D
Similar pages