Chip Inductors LCCM Series – Chip Common Mode Filter FEATURES CONSTRUCTION • Small wire wound chip inductor with ferrite core and 2 common mode lines. • Highly effective in noise suppression • High common-mode impedance at noise band an low differential mode impedance at signal band factor. There is almost no distortion in high-speed signals. • Operating temperature -40°C ~ 85°C. APPLICATIONS Ferrite • EMI suppression for electronic devices. • USB line in personal computers and peripherals. • IEEE 1394 line for personal computers, DVC, and STB • LCD Panels. • Low-Voltage Differential Signal (LVDS) Terminal Enamel-insulated Wire DIMENSIONS B A K C H K E I F J E I G mm (inches) Type Size (inch) LCCM0805 0805 LCCM1206 1206 A 2.00 (0.079 3.20 (0.126 B C ± 0.20 1.20 ± 0.20 1.20 ± 0.20 ± 0.008) (0.047 ± 0.008) (0.047 ± 0.008) ± 0.20 1.60 ± 0.20 1.80 ± 0.20 ± 0.008) (0.063 ± 0.008) (0.071 ± 0.008) E F G H I J K 0.45 (0.018) 1.20 (0.047) 0.40 (0.016) 0.80 (0.031) 0.40 (0.016) 0.40 (0.016) 0.90 (0.035) 0.60 (0.024) 2.00 (0.079) 0.60 (0.024) 1.60 (0.063) 0.60 (0.024) 0.40 (0.016) 1.05 (0.041) Weight (g) (1000pcs) 19 53.3 HOW TO ORDER LC CM 0805 M 101 G T A R Family LC = Chip Inductor Series CM = Common Mode Size 0805 1206 Tolerance M = 20% Impedance 100 = 10 Ω 101 = 100 Ω 102 = 1000 Ω Style G = Standard Termination T = Sn Plating Special A = Standard Packaging R = 7" Reel 2 Chip Inductors LCCM Series – Chip Common Mode Filter ELECTRICAL CHARACTERISTICS 0805 Impedance (Ω) Tolerance 67 90 120 180 200 260 360 370 ±20% ±20% ±20% ±20% ±20% ±20% ±20% ±20% Test Condition (MHz) 100 100 100 100 100 100 100 100 DCR (Ω) max. IDC (mA) max. Rated Voltage Vdc (V) 0.25 0.35 0.30 0.35 0.35 0.40 0.40 0.40 400 330 370 330 330 300 280 280 50 50 50 50 50 50 50 50 Test Condition (MHz) 100 100 100 100 100 100 DCR (Ω) max. IDC (mA) max. Rated Voltage Vdc (V) 0.30 0.40 0.50 0.80 1.00 1.20 370 340 310 260 230 200 50 50 50 50 50 50 Withstanding Voltage Vdc (V) 125 125 125 125 125 125 125 125 Insulation Resistance (MΩ) min. 10 10 10 10 10 10 10 10 Withstanding Voltage Vdc (V) 125 125 125 125 125 125 Insulation Resistance (MΩ) min. 10 10 10 10 10 10 1206 Impedance (Ω) Tolerance 90 160 260 600 1000 2200 ±20% ±20% ±20% ±20% ±20% ±20% 3 Chip Inductors LCCM Series – Chip Common Mode Filter LCCM0805 CHARACTERISTICS – IMPEDANCE vs. FREQUENCY LCCM0805M670 LCCM0805M900 10000 1000 1 Impedance (Ohm) 10 100 10 10 100 1000 1 Frequency (MHz) 1 1000 1 100 10 1000 10 100 1 1000 10 LCCM0805M201 LCCM0805M361 10000 1000 100 10 1 100 10 1 0.1 0.1 1 10 100 1000 Frequency (MHz) Common Mode 1 100 Frequency (MHz) Frequency (MHz) Impedance (Ohm) Impedance (Ohm) 10 0.1 1 Frequency (MHz) 1000 100 1 0.1 100 1000 1000 1 10 100 LCCM0805M371 10000 Impedance (Ohm) 10 1 10 Frequency (MHz) 1000 100 0.1 4 100 LCCM0805M181 10000 Impedance (Ohm) Impedance (Ohm) 10 Frequency (MHz) LCCM0805M121 1000 10 0.1 0.1 1 100 1 1 0.1 LCCM0805M261 10000 1000 100 Impedance (Ohm) Impedance (Ohm) 1000 10 100 Frequency (MHz) Differential Mode 1000 1000 Chip Inductors LCCM Series – Chip Common Mode Filter LCCM1206 CHARACTERISTICS – IMPEDANCE vs. FREQUENCY LCCM1206M900 LCCM1206M261 10000 100 10 1 1000 100 10 10 100 1000 1 Frequency (MHz) 100 10 1 100 Frequency (MHz) 1 1000 10 100 1000 Frequency (MHz) LCCM1206M222 10000 1000 100 10 1000 100 10 1 1 10 10 1000 Impedance (Ohm) Impedance (Ohm) Impedance (Ohm) 10 LCCM1206M601 10000 100 1 100 Frequency (MHz) LCCM1206M161 1000 1000 1 1 1 LCCM1206M102 10000 Impedance (Ohm) Impedance (Ohm) Impedance (Ohm) 1000 1 10 100 1000 Frequency (MHz) Common Mode 1 10 100 1000 Frequency (MHz) Differential Mode 5 Chip Inductors LCCM Series – Chip Common Mode Filter ENVIRONMENTAL CHARACTERISTICS ELECTRICAL PERFORMANCE TEST Items Impedance DC Resistance DCR Requirement Withstand Voltage (VDC) Refer to standard electrical characteristic spec. Component should not be damaged Rated Voltage (VDC) Insulation Resistance (I.R) Test Conditions I Test Methods LCR Meter HP 4291B Micro-Ohm meter (GOM-801G) Test Voltage: 2.5 Times Rated Voltage Testing Time: 60 seconds Charge Current: 0.5mA Test Voltage: Rated Voltage Testing Time: 1 to 5 seconds Charge Current: 1mA Charge Current: 1minute 10M ohm min. MECHANICAL PERFORMANCE TEST Items Component Adhesion (Push Test) Requirement Base: 0805 2 Lbs Cover: 0805 1 Lbs Base: 1206 4 Lbs Cover: 1206 2 Lbs Drop Component should not be damaged Solderability The terminal should at least be 90% covered with solder Vibration Test (Low Frequency) Component should not be damaged Test Conditions I Test Methods The component should be soldered (232°C ± 5°C for 10 sec.) to tinned copper substrate Applied force gauge to the side of component It must withstand force of 2 or 4 pounds without failure of the component. Dropping chip by each side and corner. Drop 10 times in total Drop height: 100 cm Drop weight: 125 g The component shall be dipped in a melted solder bath at 245 ±5°C for 3 seconds 1. 2. 3. 4. Amplitude: 1.5 m/m Frequency: 10-55-10Hz (1min.) Direction: X, Y, Z Duration: 2 Hrs/X, Y, Z MECHANICAL PERFORMANCE TEST Items Requirement Low Temperature Storage Test Conditions I Test Methods 1. Temp: -40 ±2°C 2. Time: 1000±48 Hours 3. Component should be tested after 1 hour at room temperature ROOM TEMP Thermal Shock Impedance change: Within± 20% Without distinct damage in appearance High Temperature Storage Humidity High Temperature Load Life There should be no evidence of short or open circuit Low Temperature Load Life 6 -25 ± 2ºC 15 MINS 30 MINS ROOM TEMP 85 ± 2ºC Total: 5 Cycles 15 MINS 30 MINS 1. Temp: 85 ± 2°C 2. Time: 1000 ± 48 Hours 3. Component should be tested after 1 hour at room temperature 1. Temp: 40 ± 2°C 2. R.H. : 90 — 95% 3. Time: 48 ±2 Hours 1. Temp: 85 ± 2°C 2. Time: 96 ± 12 Hours 3. Load: Allowed DC Current 1. Temp: -40 ± 2°C 2. Time: 96 ± 12 Hours 3. Load: Allowed DC Current Chip Inductors LCCM Series – Chip Common Mode Filter PACKAGING QUANTITY REAL SPECIFICATIONS 1.20 ± 0.20 (0.047 ± 0.008) D: 21.8 ± 0.80 (0.858 ± 0.031) Type LCCM0805 LCCM1206 Label 178 ± 2.00 (7.008 ± 0.079) Embossed Plastic Tape (EA) 2,000 2,000 60.0 ± 0.50 (2.362 ± 0.020) D: 13.0 ± 0.30 (0.512 ± 0.012) 9.00 ± 0.30 (0.354 ±0.0112) 2.00 ± 0.50 (0.079 ±0.020) 11.4 ± 1.00 (0.449 ± 0.039) EMBOSSED PLASTIC TAPE SPECIFICATIONS Top Tape ψ D0 E A F B W ψ D11.5 Min. T P1 P2 P0 Direction of unreeling Embossed Tape mm (inches) A B W E F P0 P1 P2 ΦD0 T 1.40 ± 0.10 2.55 ± 0.05 8.0 ± 0.20 1.75 ± 0.10 3.50 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 2.00 ± 0.10 1.50 ± 0.10 1.35 ± 0.10 LCCM0805 (0.055 ± 0.004) (0.100 ± 0.002) (0.315 ± 0.008) (0.069 ± 0.004) (0.138 ± 0.004) (0.157 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.004) (0.059 ± 0.004) (0.053 ± 0.004) 1.90 ± 0.10 3.50 ± 0.05 8.0 ± 0.20 1.75 ± 0.10 3.5 ± 0.10 4.00 ± 0.10 4.00 ± 0.10 2.00 ± 0.10 1.50 ± 0.10 2.10 ± 0.10 LCCM1206 (0.075 ± 0.004) (0.138 ± 0.004) (0.315 ± 0.008) (0.069 ± 0.004) (0.138 ± 0.004) (0.157 ± 0.004) (0.157 ± 0.004) (0.079 ± 0.004) (0.059 ± 0.004) (0.083 ± 0.004) Type LEADER/TAPE Trailer End Leader Trailer 80.0 (3.150) min. Empty Compartments with Cover Tape 80.0 (3.150) min. Cover Tape Only 450 (17.72) min. PEEL-OFF FORCE The force for tearing off cover tape is 0.05 - 0.69 (N) in the arrow direction at the following conditions: Temperature: 5 - 35°C Humidity: 45 - 85% Atmospheric pressure: 860 - 1060hpa 160 - 180º Top cover tape Base tape 7