GLASS PASSIVATED SINGLE-OHASE BPIDGE RECTIFIER GBPC4005 THRU GBPC4010 VOLTAGE RANGE 50 to 1000 Volts CURRENT 40.0 Amperes GBPC35 FEATURES • • • • • • 1.135(28.8) 1.115(28.3) 0.72(17.1) Plastic package has UL flammability classification 94V-0 Integrally molded heatsink provides very low thermal resistance for maximum heat dissipation High forward surge capacity Glass passivated chip junction High isolation voltage from case to lugs High temperature soldering guaranteed: 260℃/10 seconds, .632(16.1) AC + 1.135(28.8) .672(17.1) .582(14.8) 1.115(28.3) .632(16.1) .542(13.8) AC .692(17.6) 0.094(2.4)DIA. 0.034(.86) .25(6.35) 0.030(.76) MECHANICAL DATA • • • • • • .732(18.6) Case:Epoxy, Molded Plastic with integrally mounted heatsink Terminals: Plated 0.25”(6.35mm) lug Polarity: Polarity symbols market on case Mounting: Thru hole for #10 screw, 20 in-lbs Torque max. Weight: 0.62 ounce, 17.5 gram .840(21.3) .740(18.8) .310(7.87) .290(7.36) .220(5.59) .100(5.08) METAL HEAT SINK HOLE FOR #10 SCREW Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% SYMBOLS GBPC GBPC Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current At TC=55℃ (SEE FIG.1) Peak Forward Surge Current 8.3mS single half sine wave superimposed on rated load (JEDEC method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per Bridge element 20.0A TA = 25℃ Maximum DC Reverse Current at rated DC blocking Voltage per element TA = 125℃ Isolation Voltage from case to lug Typical Thermal Resistance (Note 1 and 2) Operating Junction Temperature Storage Temperature Range VRRM VRMS VDC GBPC GBPC GBPC GBPC GBPC 40005 4001 4002 4004 4006 4008 4010 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 UNIT Volts Volts Volts I(AV) 35 Amps IFSM 300 Amps I2 t 660 A2s VF 1.1 Volts 5.0 500 2500 1.4 (-55 to +150) (-55 to +150) µA IR VISO RΘJC TJ TSTG Volts ℃/W ℃ ℃ Notes: 1.Unit mounted on 9”×3.5”×4.6”(23cm×9cm×11.8cm) AL Plate. 2.Bolt down on heat-sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer efficiency with#10 screw E-mail: [email protected] Web Site: www.cnmic.com GLASS PASSIVATED SINGLE-OHASE BPIDGE RECTIFIER GBPC4005 THRU GBPC4010 VOLTAGE RANGE 50 to 1000 Volts CURRENT 40.0 Amperes RATINGS AND CHARACTERISTICS CURVES GBPC40005 THRU GBPC4010 FIG. 1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 700 45 PEAK FORWARD SURGE CURRENT,(A) AVERAGE FORWARD CURRENT, (A) 50 Heat Sink Mounting 9" × 3.5" ×4.6" Thick (23× 9× 11.8cm) AL. Finned Plate 40 35 30 25 20 15 Single Phase Half wave 60Hz lnductive of Resistive Load 10 5 0 25 0 600 8.3ms Single Half-Wave (JEDEC Method) T j =T j max 500 400 300 200 100 1 CYCLE 1 75 50 100 125 150 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60 Hz 175 CASE TEMPERATURE (℃ ) FIG. 3- TYPICAL FORWARD CHARACTERISTICS PER BRIDGE LEMENT FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER BRIDGE LEMENT 100 INSTANTANEOUS REVERSE CURRENT, (μA) INSTANTANEOUS FORWARD CURRENT, (A) 100 10 1.0 TJ =25℃ PULSE WIDTH=300μs 1% DUTY CYCLE 0.1 TJ =100℃ 10 1.0 TJ =25℃ 0.1 0.01 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0 AVERAGE POWER DIS SIPATION OF BRIDGE (W) FIG. 5- MAXIMUM POWER DISSIPATION 100 80 Tj =T j max Capacitive Load 60 40 Resistive or Inductive Load 20 0 0 5 10 15 20 25 30 35 40 45 50 AVERAGE OUTPUT CURRENT, (A) E-mail: [email protected] 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS FORWARD VOLTAGE, (V) Web Site: www.cnmic.com 120 140