Toshiba MT6L05FS Vhf~uhf band low-noise amplifier application Datasheet

MT6L05FS
TOSHIBA Transistor Silicon NPN Epitaxial Planar Type
MT6L05FS
VHF~UHF Band Low-Noise Amplifier Applications
Unit: mm
1.0±0.05
0.8±0.05
MT3S05T
(MT3S05FS)
Corresponding three-pin products:TESM(fSM) mold products
6
2
5
3
4
+0.02
Q1/Q2
1
0.48 -0.04
Mounted Devices
0.1±0.05
0.1±0.05
1.0±0.05
0.7±0.05
z Superior noise characteristics
z Superior performance in buffer and oscillator applications.
0.35 0.35
0.1±0.05
0.15±0.05
Two devices are incorporated in a fine-pitch, small-mold package (6 pins): fS6.
fS6
1. Collector1 (C1)
2. Emitter1 (E1)
3. Collector2 (C2)
4. Base2 (B2)
5. Emitter2 (E2)
6. Base1 (B1)
Absolute Maximum Ratings (Ta = 25°C)
Characteristic
Symbol
Rating
Unit
Collector- base voltage
VCBO
10
V
Collector- emitter voltage
VCEO
5
V
Emitter- base voltage
VEBO
2
V
Collector current
IC
40
mA
Base current
IB
10
mA
Collector power dissipation
Junction temperature
Storage temperature range
Note:
100
PC(Note 1)
JEDEC
JEIAJ
Toshiba
―
―
2-1F1A
Weight: 0.001g (typ.)
mW
110 (Note 2)
Tj
125
°C
Tstg
−55~125
°C
Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change
in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e.
operating temperature/current/voltage, etc.) are within the absolute maximum ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling
Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure
rate, etc).
2
Note 1: 10 mm × 1.0 mm (t), mounted on a glass-epoxy printed circuit board.
Note 2: During two-element operation
Marking (top view)
6
5
4
32
1
Pin Assignment (top view)
6
5
Q1
2
3
1
4
Q2
2
1
3
2007-11-01
MT6L05FS
Electrical Characteristics Q1/Q2 (Ta = 25°C)
Characteristic
Symbol
Condition
Min
Typ.
Max
Unit
Collector cutoff current
ICBO
VCB = 5 V, IE = 0
⎯
⎯
0.1
μA
Emitter cutoff current
IEBO
VEB = 1 V, IC = 0
⎯
⎯
1
μA
DC current gain
Reverse transfer capacitance
Transition frequency
Insertion gain
Noise figure
hFE
Cre (Note)
VCE = 1 V, IC = 5 mA
80
⎯
140
VCB = 1 V, IE = 0, f = 1 MHz
⎯
0.9
1.15
pF
GHz
VCE = 1 V, IC = 5 mA
2
4.5
⎯
2
VCE = 1 V, IC = 5 mA, f = 1 GHz
⎯
8.5
⎯
2
⎪S21e⎪ (2)
VCE = 3 V, IC = 20 mA, f = 1 GHz
8.5
11.5
⎯
NF
VCE = 1 V, IC = 5 mA, f = 1 GHz
⎯
1.4
2.2
fT
⎪S21e⎪ (1)
dB
dB
Note: Cre is measured with a three-terminal method using a capacitance bridge.
Caution
This device is sensitive to electrostatic discharge. Ensure that tools and equipment are sufficiently grounded before
handling. When handling individual devices (which are not yet mounted on a circuit board), ensure that the
environment is protected against electrostatic discharge. Operators should wear antistatic clothing, and containers
and other objects that come into direct contact with devices should be made of antistatic materials.
2
2007-11-01
MT6L05FS
RESTRICTIONS ON PRODUCT USE
20070701-EN GENERAL
• The information contained herein is subject to change without notice.
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc.
• The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his
document shall be made at the customer’s own risk.
• The products described in this document shall not be used or embedded to any downstream products of which
manufacture, use and/or sale are prohibited under any applicable laws and regulations.
• The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which
may result from its use. No license is granted by implication or otherwise under any patents or other rights of
TOSHIBA or the third parties.
• Please contact your sales representative for product-by-product details in this document regarding RoHS
compatibility. Please use these products in this document in compliance with all applicable laws and regulations
that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses
occurring as a result of noncompliance with applicable laws and regulations.
3
2007-11-01
Similar pages