MC100LVEL33 3.3VECL ÷4 Divider Description The MC100LVEL33 is an integrated ÷4 divider. The LVEL is functionally equivalent to the EL33 and works from a 3.3 V supply. The reset pin is asynchronous and is asserted on the rising edge. Upon power-up, the internal flip-flops will attain a random state; the reset allows for the synchronization of multiple LVEL33’s in a system. The VBB pin, an internally generated voltage supply, is available to this device only. For single-ended input conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 mF capacitor and limit current sourcing or sinking to 0.5 mA. When not used, VBB should be left open. Features • 630 ps Typical Propagation Delay • 4.0 GHz Typical Maximum Frequency • ESD Protection: >4 kV Human Body Model, • • • • • • • MARKING DIAGRAMS* 8 1 SOIC−8 D SUFFIX CASE 751 8 1 >200 V Machine Model The 100 Series Contains Temperature Compensation PECL Mode Operating Range: VCC = 3.0 V to 3.8 V with VEE = 0 V NECL Mode Operating Range: VCC= 0 V with VEE = −3.0 V to −3.8 V Internal Input Pulldown Resistors Meets or Exceeds JEDEC Spec EIA/JESD78 IC Latchup Test Moisture Sensitivity Level 1 For Additional Information, see Application Note AND8003/D Flammability Rating: UL 94 V−0 @ 0.125 in, Oxygen Index: 28 to 34 Transistor Count = 130 devices Pb−Free Packages are Available TSSOP−8 DT SUFFIX CASE 948R 8 KVL33 ALYW G 1 8 1 KV33 ALYWG G 4F M G G • • http://onsemi.com DFN8 MN SUFFIX CASE 506AA 1 4 A = Assembly Location L = Wafer Lot Y = Year W = Work Week M = Date Code G = Pb−Free Package (Note: Microdot may be in either location) *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. © Semiconductor Components Industries, LLC, 2006 December, 2006 − Rev. 4 1 Publication Order Number: MC100LVEL33/D MC100LVEL33 Table 1. PIN DESCRIPTION Reset CLK 1 8 R 2 VCC 7 Q 6 Q PIN ÷4 CLK VBB 3 4 5 FUNCTION CLK*, CLK** Q, Q Reset* VBB VCC VEE ECL Differential Clock Inputs ECL Differential Data ÷4 Outputs ECL Asynch Reset Reference Voltage Output Positive Supply Negative Supply EP Exposed pad must be connected to a sufficient thermal conduit. Electrically connect to the most negative supply or leave floating open. VEE Figure 1. Logic Diagram and Pinout Assignment * Pins will default LOW when open due to internal 75 kW resistor to VEE ** Pins will default to 1/2 VCC when open due to internal resistors: 75 kW to VEE and 75 kW to VCC Table 2. MAXIMUM RATINGS Symbol Parameter Condition 1 Condition 2 Rating Unit VCC PECL Mode Power Supply VEE = 0 V 8 to 0 V VEE NECL Mode Power Supply VCC = 0 V −8 to 0 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 to 0 −6 to 0 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm 8 SOIC 8 SOIC 190 130 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board 8 SOIC 41 to 44 ± 5% °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm 8 TSSOP 8 TSSOP 185 140 °C/W °C/W qJC Thermal Resistance (Junction−to−Case) Standard Board 8 TSSOP 41 to 44 ± 5% °C/W qJA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm DFN8 DFN8 129 84 °C/W °C/W Tsol Wave Solder <2 to 3 sec @ 248°C <2 to 3 sec @ 260°C 265 265 °C Pb Pb−Free VI VCC VI VEE Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. http://onsemi.com 2 MC100LVEL33 Table 3. LVPECL DC CHARACTERISTICS VCC = 3.3 V; VEE = 0.0 V (Note 1) −40°C Symbol Characteristic Min 25°C Typ Max 33 37 Min 85°C Typ Max 33 37 Min Typ Max Unit 35 39 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 2) 2215 2295 2420 2275 2345 2420 2275 2345 2420 mV VOL Output LOW Voltage (Note 2) 1470 1605 1745 1490 1595 1680 1490 1595 1680 mV VIH Input HIGH Voltage (Single−Ended) 2135 2420 2135 2420 2135 2420 mV VIL Input LOW Voltage (Single−Ended) 1490 1825 1490 1825 1490 1825 mV VBB Output Voltage Reference 1.92 2.04 1.92 2.04 1.92 2.04 V VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 6) VPP < 500 mV VPP y 500 mV 1.2 2.9 1.1 2.9 1.1 2.9 V 1.4 2.9 1.3 2.9 1.3 2.9 V 150 mA IIH Input HIGH Current IIL Input LOW Current 150 Other CLK 150 0.5 0.5 0.5 mA −600 −600 −600 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 1. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V. 2. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. 3. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. Table 4. LVNECL DC CHARACTERISTICS VCC = 0.0 V; VEE = −3.3 V (Note 4) −40°C Symbol Characteristic Min 25°C Typ Max 33 37 Min 85°C Typ Max 33 37 Min Typ Max Unit 35 39 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 5) −1085 −1005 −880 −1025 −955 −880 −1025 −955 −880 mV VOL Output LOW Voltage (Note 5) −1830 −1695 −1555 −1810 −1705 −1620 −1810 −1705 −1620 mV VIH Input HIGH Voltage (Single−Ended) −1165 −880 −1165 −880 −1165 −880 mV VIL Input LOW Voltage (Single−Ended) −1810 −1475 −1810 −1475 −1810 −1475 mV VBB Output Voltage Reference −1.38 −1.26 −1.38 −1.26 −1.38 −1.26 V VIHCMR Input HIGH Voltage Common Mode Range (Differential) (Note 6) VPP < 500 mV VPP y 500 mV −2.1 −0.4 −2.2 −0.4 −2.2 −0.4 V −1.9 −0.4 −2.0 −0.4 −2.0 −0.4 V 150 mA IIH Input HIGH Current IIL Input LOW Current 150 Other CLK 150 0.5 0.5 0.5 mA −600 −600 −600 mA NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 4. Input and output parameters vary 1:1 with VCC. VEE can vary ±0.3 V. 5. Outputs are terminated through a 50 W resistor to VCC − 2.0 V. 6. VIHCMR min varies 1:1 with VEE, max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1 V. http://onsemi.com 3 MC100LVEL33 Table 5. AC CHARACTERISTICS VCC = 3.3 V; VEE = 0.0 V or VCC = 0.0 V; VEE = −3.3 V (Note 7) −40°C Symbol Characteristic Min fmax Maximum Toggle Frequency tPLH tPHL Propagation Delay Typ 25°C Max 3.4 CLK to Q (Diff) CLK to Q (SE) Reset to Q 530 530 500 630 655 730 780 700 300 Min Typ 3.8 4.0 570 570 520 670 695 85°C Max Min 770 820 720 650 650 580 Reset Recovery 300 tskew Duty Cycle Skew (Note 8) tJITTER Cycle−to−Cycle Jitter VPP Input Voltage Swing (Differential Configuration) 150 1000 150 1000 tr tf Output Rise/Fall Times Q (20% − 80%) 120 320 120 320 750 775 850 900 780 ps ps 20 0.5 Unit GHz 300 20 <1.0 Max 3.8 tRR 0.5 Typ 20 ps <1.0 ps 150 1000 mV 120 320 ps <1.0 0.5 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 7. VEE can vary ±0.3 V. 8. Duty cycle skew is the difference between TPLH and TPHL. CLK RESET Q Figure 1. Timing Diagram Q Zo = 50 W D Receiver Device Driver Device Q D Zo = 50 W 50 W 50 W VTT VTT = VCC − 3.0 V Figure 2. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) http://onsemi.com 4 MC100LVEL33 ORDERING INFORMATION Package Shipping† SOIC−8 98 Units / Rail MC100LVEL33DG SOIC−8 (Pb−Free) 98 Units / Rail MC100LVEL33DR2 SOIC−8 2500 / Tape & Reel MC100LVEL33DR2G SOIC−8 (Pb−Free) 2500 / Tape & Reel MC100LVEL33DT TSSOP−8 100 Units / Rail MC100LVEL33DTG TSSOP−8 (Pb−Free) 100 Units / Rail MC100LVEL33DTR2 TSSOP−8 2500 / Tape & Reel MC100LVEL33DTR2G TSSOP−8 (Pb−Free) 2500 / Tape & Reel MC100LVEL33MNR4 DFN8 1000 / Tape & Reel DFN8 (Pb−Free) 1000 / Tape & Reel Device MC100LVEL33D MC100LVEL33MNR4G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1672/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 5 MC100LVEL33 PACKAGE DIMENSIONS SOIC−8 NB CASE 751−07 ISSUE AH −X− NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. 751−01 THRU 751−06 ARE OBSOLETE. NEW STANDARD IS 751−07. A 8 5 S B 1 0.25 (0.010) M Y M 4 −Y− K G C N DIM A B C D G H J K M N S X 45 _ SEATING PLANE −Z− H 0.10 (0.004) D 0.25 (0.010) M Z Y S X M J S SOLDERING FOOTPRINT* 1.52 0.060 7.0 0.275 4.0 0.155 0.6 0.024 1.270 0.050 SCALE 6:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 6 MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0 _ 8 _ 0.010 0.020 0.228 0.244 MC100LVEL33 PACKAGE DIMENSIONS TSSOP−8 DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948R−02 ISSUE A 8x 0.15 (0.006) T U 0.10 (0.004) S 2X L/2 L 8 5 1 PIN 1 IDENT 0.15 (0.006) T U K REF S M T U V S 0.25 (0.010) B −U− 4 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH. PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE −W−. S M A −V− F DETAIL E C 0.10 (0.004) −T− SEATING PLANE D −W− G DETAIL E http://onsemi.com 7 DIM A B C D F G K L M MILLIMETERS MIN MAX 2.90 3.10 2.90 3.10 0.80 1.10 0.05 0.15 0.40 0.70 0.65 BSC 0.25 0.40 4.90 BSC 0_ 6_ INCHES MIN MAX 0.114 0.122 0.114 0.122 0.031 0.043 0.002 0.006 0.016 0.028 0.026 BSC 0.010 0.016 0.193 BSC 0_ 6_ MC100LVEL33 PACKAGE DIMENSIONS DFN8 CASE 506AA−01 ISSUE D D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994 . 2. CONTROLLING DIMENSION: MILLIMETERS. 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A B PIN ONE REFERENCE 2X 0.10 C 2X ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ ÇÇÇÇ 0.10 C TOP VIEW 0.08 C SEATING PLANE MILLIMETERS MIN MAX 0.80 1.00 0.00 0.05 0.20 REF 0.20 0.30 2.00 BSC 1.10 1.30 2.00 BSC 0.70 0.90 0.50 BSC 0.20 −−− 0.25 0.35 A 0.10 C 8X DIM A A1 A3 b D D2 E E2 e K L E (A3) SIDE VIEW A1 C D2 e e/2 4 1 8X L E2 K 8 5 8X b 0.10 C A B 0.05 C NOTE 3 BOTTOM VIEW ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 8 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC100LVEL33/D