ADJUSTABLE VOLTAGE REGULATOR (POSITIVE) LM317L 3-TERMINAL 100mA POSITIVE ADJUSTABLE REGULATOR TO-92 PKG FEATURES 3. VIN 2. VOUT ● Output current in Excess of 100mA ● Output Adjustable Between 1.2V and 37V ● Internal Thermal-Overload Protection ● Internal Short-Circuit Current-Limiting ● Output Transistor Safe-Area Compensation ● Floating operation for high voltage applications ● Moisture Sensitivity Level 3 1. ADJ SOT-89 PKG DISCRIPTION 1.Adj 2. Vout 3. Vin This monolithic integrated circuit is an adjustable 3-terminal positive voltage regulator designed to supply more than 100mA of load current with an output voltage adjustable over a 1.2 to 37V. It employs internal current limiting, thermal shut-down and safe area compensation. ORDERING INFORMATION Device LM317L LM317F Marking LM317L 317 Package TO-92 SOT-89 BLOCK DIAGRAM HTC Jun. 2009 - Rev.1.1 1 ADJUSTABLE VOLTAGE REGULATOR (POSITIVE) LM317L TYPICAL APPLICATIONS Fig.5 Programmable Regulator CI is required when regulator is located in appreciable distance from power supply filter. Co is not needed for stability, however, it does improve transient response. Since lADJ is controlled to less than 100㎂, the error associated with this term is negligible in most applications. HTC 2 ADJUSTABLE VOLTAGE REGULATOR (POSITIVE) LM317L ABSOLUTE MAXIMUM RATINGS (T A=25℃, unless otherwise specified) Characteristic Input-output Voltage Differential Lead Temperature Power Dissipation Operating Temperature Range Storage Temperature Range Symbol VI-Vo TLEAD PD TOPR TSTG Unit V ℃ ℃ ℃ Value 40 230 Internally limited 0 ∼ +125 -65 ∼ +125 ELECTRICAL CHARACTERISTICS (VI-Vo=5V, Io=40mA, 0℃≤TJ≤125℃, IMAX=100mA, unless otherwise specified) Characteristic Line Regulation Load Regulation Adjustable Pin Current Adjustable Pin Current Cha Symbol △Vo △Vo △IADJ VREF Temperature Stability Minimum Load Current to Maintain Regulation STT L(MIN) Io(MAX) RMS Noise, % of VOUT eN Ripple Rejection RR Long-Term Stability, TJ=THIGH Min. IADJ Reference Voltage Maximum Output Current Test condition 3V≤VI-Vo≤40V TA=0 ∼ 125℃ 3V≤VI-Vo≤40V TA=25℃, 10㎃≤Io≤IMAX Vo≤5V Vo≥5V 10㎃≤Io≤IMAX Vo≤5V Vo≥5V ST 3V≤VI-Vo≤40V 10㎃≤Io≤IMAX P≤PMAX 3V≤VIN-VOUT≤40V 10㎃≤Io≤IMAX PD≤PMAX 1.20 Typ. 0.01 0.02 Max. 0.04 0.07 Unit %/V %/V 10 0.1 25 0.5 ㎷ %/Vo 20 0.3 46 70 1.5 100 ㎷ %/Vo ㎂ 0.2 5 ㎂ 1.25 1.30 V 0.7 VI-Vo=40V VI-Vo≤5V, PD≤PMAX VI-Vo≤40V, PD≤PMAX, TA = 25℃ TA=25℃, 10Hz≤f≤10KHz Vo=10V, f=120Hz without CADJ CADJ=10 ㎌ TA=25℃, for end point measurements, 1000HR 3.5 100 156 66 200 400 0.003 %/Vo 10 ㎃ 0.01 ㎃ ㎃ %/Vo 60 75 0.3 ㏈ 1 % * Load and line regulation are specified at constant junction temperature. Change in VD due to heating effects must be taken into account separately. Pulse testing with low duty is used. HTC 3