AWT6332 ZeroIC PCS/CDMA 3.4V/28dBm Linear Power Amplifier Module TM Data Sheet - Rev 2.1 FEATURES • InGaP HBT Technology • High Efficiency: 37 % @ +28 dBm output • Zero Quiescent Current in Switch Mode • Internal Voltage Regulation • Optimized for a 50 Ω System • Low Profile Surface Mount Package: 1 mm • CDMA 1XRTT, 1xEV-DO Compliant • RoHS-Compliant Package, 250 oC MSL-3 APPLICATIONS • CDMA/EVDO PCS-band Wireless Handsets and Data Devices PRODUCT DESCRIPTION The AWT6332 is a new product in the revolutionary ZeroIC™ PA family. The AWT6332 uses ANADIGICS’ exclusive InGaP-Plus™ technology, which combines HBT and pHEMT devices on the same die, to enable state-of-the-art reliability, temperature stability, and ruggedness. The AWT6332 has a unique architecture with two RF inputs. One input drives the power amplifier while the other input drives an RF switch that bypasses the power amplifier, going directly to the RF output. The mode control logic selects the PA or the RF switch. In M27 Package 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module RF switch mode, current consumption is less than 10 A, reducing the average current consumption 70% more than a HELP2™ PA over the CDG profile. Its integrated voltage regulator eliminates the need for external components further reducing size and BOM cost. The 3 mm x 3 mm x 1 mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 system. Figure 1: Block Diagram 09/2008 AWT6332 Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 VBATT Battery Voltage 2 RFIN_SWITCH 3 RFIN_PA RF Input to PA 4 VMODE Mode Control Voltage 5 VEN 6 GND Ground 7 GND Ground 8 RFOUT RF Output 9 VCC Supply Voltage 10 VCC Supply Voltage RF Input to Switch PA Enable Voltage Data Sheet - Rev 2.1 09/2008 AWT6332 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC and VBATT) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Enable Voltage (VEN) 0 +3.5 V RF Input Power (PIN) to PA - +10 dBm RF Input Power (PIN) to Switch - +20 dBm -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT Operating Frequency (f) 1850 - 1915 MHz Supply Voltage (VCC and VBATT) +3.2 +3.4 +4.2 V Enable Voltage (VEN) +2.2 0 +2.4 - +3.1 +0.5 V PA "on", Switch "on" PA "shut down" Mode Control Voltage (VMODE) +2.2 0 +2.4 - +3.1 +0.5 V PA Mode Switch Mode +28.0 - dBm - +85 °C RF Output Power (POUT) 27.5 Case Temperature (TC) -30 (1) COMMENTS The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at VCC = +3.2 V, POUT is derated by 0.5 dB. Data Sheet - Rev 2.1 09/2008 3 AWT6332 Table 4: Electrical Specifications - CDMA Operation (IS-95 Modulation) (TC = +25 °C, VBATT = VCC = +3.4 V, VEN = +2.4 V, 50 Ω system) COMMENTS PARAMETER MIN TYP MAX UNIT Gain Insertion Loss 24.5 - 27 0.8 29.5 1.5 dB Adjacent Channel Power at +1.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz - -51 -70 -46.5 - Adjacent Channel Power at +2.25 MHz offset Primary Channel BW - 1.23 MHz Adjacent Channel BW = 30 kHz - -59.5 -70 -56.5 - dBc POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V 31 34 - dB RFOUT to RFIN_SWITCH, VMODE = +2.4 V, PA "on" 34.5 37 - % POUT = +28 dBm, VMODE = +2.4 V Enable Current - <0.1 0.25 mA through VEN pin, VEN = +2.4 V Mode Control Current - <0.01 0.1 mA through VMODE pin, VMODE = +2.4 V - <10 15 - <10 18 Noise in Receive Band - -136 -134 Harmonics 2fo 3fo, 4fo - -40 -45 -30 -30 dBc Input Impedance - - 2:1 VSWR Isolation Power-Added Efficiency Leakage Current Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure µA POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V VCC = +4.2 V, VEN = 0 V, VMODE = 0 V or +2.4 V VCC = +4.2 V, VEN = +2.4 V, VMODE = 0 V, Switch Mode dBm/Hz 1930 MHz to 1990 MHz CW Measurement - - -65 dBc POUT < +28 dBm In-band load VSWR < 5:1 Out-of-band load VSWR < 10:1 Applies over all operating ranges 8:1 - - VSWR Applies over full operating range Notes: (1) PAE and ACP limit applies at 1880 MHz (IS-95 modulation). 4 dBc POUT = +28 dBm, VMODE = +2.4 V VMODE = 0 V Data Sheet - Rev 2.1 09/2008 AWT6332 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying a logic low levels (see Operating Ranges table) to both the VEN and VMODE voltages. Power Modes The power amplifier may be placed in either a Low Power mode or a High Power mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Power Control table lists the recommended modes of operation for various applications. Table 5: Power Control POUT LEVELS POWER MODE VEN VMODE CDMA - Switch Bypass -* Low +2.4 V 0V Shutdown -* Low 0V +2.4 V CDMA - PA All High +2.4 V +2.4 V - Shutdown 0V 0V APPLICATION Shutdown *Dependent upon typical output power of Transceiver and phone board design. Figure 3: Application Circuit Data Sheet - Rev 2.1 09/2008 5 AWT6332 PACKAGE OUTLINE Figure 4: M27 Package Outline - 10 Pin 3 mm x 3 mm x 1 mm Surface Mount Module Figure 5: Branding Specification 6 Data Sheet - Rev 2.1 09/2008 AWT6332 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 6: Tape & Reel Dimensions PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 3 mm x 3 mm x 1 mm 12 mm 4 mm 2500 7" Data Sheet - Rev 2.1 09/2008 7 AWT6332 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWT6332RM27Q7 -30 °C to +85 °C RoHS-Compliant 10 Pin 3 mm x 3 mm x 1 mm Tape and Reel, 2500 pieces per Reel Surface Mount Module AWT6332RM27P9 -30 °C to +85 °C RoHS-Compliant 10 Pin 3 mm x 3 mm x 1 mm Partial Tape and Reel Surface Mount Module COMPONENT PACKAGING ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. warning ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 8 Data Sheet - Rev 2.1 09/2008