IHL02 Series DC-DC Converter 2 Watts xxx Series • High Isolation, 5200 V • 250 VAC Working Voltage • Single and Dual Outputs • Bipolar Outputs for MOSFET and IGBT Drives • SIP7 Package • -40 °C to +95 °C Operation • Full Load at 65 °C Ambient • MTBF 2.5 MHrs • 3 Year Warranty Dimensions: IHL02: 0.77 x 0.28 x 0.39” (19.5 x 7.2 x 10.0 mm) Input Characteristic Minimum 4.5 10.8 13.5 21.6 Input Voltage Range Typical Input Reflected Ripple Current maximum 5.5 13.2 16.5 26.4 20 VDC mA pk-pk 9 18 20 30 Input Surge Units VDC for 100 ms Notes & Conditions 5 V nominal 12 V nominal 15 V nominal 24 V nominal Through 12 µH inductor and 47 µF capacitor 5 V nominal 12 V nominal 15 V nominal 24 V nominal Output Characteristic Output Voltage Initial Set Accuracy Minimum Load Minimum 3.3 Typical maximum 30 ±5 Units VDC % % Line Regulation ±1.2 %/1% Load Regulation 12/10 % 10 Cross Regulation ±5 Notes & Conditions See Models and Ratings table At full load Minimum load required to meet specified regulation Output changes by max of 1.2% for each 1% change in input voltage For IHL0205S3V3 and IHL0205S05/Other Models. From 10% to full load, see application note % Ripple & Noise 150 mV pk-pk Short Circuit Protection Maximum Capacitive Load Temperature Coefficient 0.03 %/ ˚C On dual output models, when one output is at 25% load and other is varied from 10% load to full load 20 MHz bandwidth. Measured using 10 µF electrolytic in parallel with 0.1 µF ceramic capacitor Continuous See Models and Ratings table Mechanical Details 0.28 (7.2) 0.76 (19.5) 0.12 (3.0) 0.37 (9.5) 0.02 (0.5) 0.10 (2.54) Notes 0.08 (2.0) 0.02 (0.5) 0.28 (7.2) 0.39 (10.0) 0.02 (0.5) 0.60 (15.24) 0.08 (2.13) 1. All dimensions are in inches (mm) 2. Weight: 0.006 lbs (2.7 g) approx. 3. Pin diameter: 0.02±0.002 (0.5±0.05) 1 0.01 Printed (0.25) Face 0.08 (2.13) 4. Pin pitchand length tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) www.xppower.com Pin Connections Pin 1 2 5 6 7 Single +Vin -Vin -Vout No Pin +Vout Dual +Vin -Vin -Vout Common +Vout IHL02 Series DC-DC Converter Models & Ratings Input Voltage 4.5-5.5V 10.8-13.2V 13.5-16.5V 21.6-26.4V Output Voltage Output Current 3V3 5V 9V 12 V 15 V ±5 V ±9 V ±12 V ±15 V +15/-9 V 3V3 5V 9V 12 V 15 V ±5 V ±9 V ±12 V ±15 V +15/-9V 3V3 5V 9V 12 V 15 V ±5 V ±9 V ±12 V ±15 V +15/-9V 3V3 5V 9V 12 V 15 V ±5 V ±9 V ±12 V ±15 V +15/-9V 500 mA 400 mA 222 mA 167 mA 133 mA ±200 mA ±111 mA ±83.3 mA ±66.7 mA +66.7/-111 mA 500 mA 400 mA 222 mA 167 mA 133 mA ±200 mA ±111 mA ±83.3 mA ±66.7 mA +66.7/-111 mA 500 mA 400 mA 222 mA 167 mA 133 mA ±200 mA ±111 mA ±83.3 mA ±66.7 mA +66.7/-111 mA 500 mA 400 mA 222 mA 167 mA 133 mA ±200 mA ±111 mA ±83.3 mA ±66.7 mA +66.7/-111 mA Input current No Load Full Load 40 mA 435 mA 40 mA 505 mA 40 mA 480 mA 40 mA 475 mA 40 mA 470 mA 40 mA 505 mA 40 mA 490 mA 40 mA 480 mA 40 mA 475 mA 40 mA 480 mA 30 mA 185 mA 30 mA 210 mA 30 mA 205 mA 30 mA 205 mA 30 mA 200 mA 30 mA 210 mA 30 mA 205 mA 30 mA 200 mA 30 mA 200 mA 30 mA 210 mA 25 mA 150 mA 25 mA 170 mA 25 mA 165 mA 25 mA 165 mA 25 mA 160 mA 25 mA 170 mA 25 mA 165 mA 25 mA 160 mA 25 mA 165 mA 25 mA 165 mA 20 mA 95 mA 20 mA 105 mA 20 mA 105 mA 20 mA 105 mA 20 mA 105 mA 20 mA 105 mA 20 mA 105 mA 20 mA 105 mA 20 mA 100 mA 20 mA 105 mA Maximum Capacitive Load Efficiency Model Number 1000 µF 470 µF 470 µF 220 µF 220 µF ±220 µF ±220 µF ±100 µF ±100 µF +100/-220 µF 1000 µF 470 µF 470 µF 220 µF 220 µF ±220 µF ±220 µF ±100 µF ±100 µF +100/-220 µF 1000 µF 470 µF 470 µF 220 µF 220 µF ±220 µF ±220 µF ±100 µF ±100 µF +100/-220 µF 1000 µF 470 µF 470 µF 220 µF 220 µF ±220 µF ±220 µF ±100 µF ±100 µF +100/-220 µF 76% 79% 83% 84% 85% 79% 82% 83% 84% 83% 74% 79% 82% 82% 83% 79% 81% 83% 83% 80% 74% 78% 81% 82% 83% 79% 81% 83% 82% 81% 73% 78% 81% 81% 81% 79% 80% 81% 82% 80% IHL0205S3V3 IHL0205S05 IHL0205S09 IHL0205S12 IHL0205S15 IHL0205D05 IHL0205D09 IHL0205D12 IHL0205D15 IHL0205D1509 IHL0212S3V3 IHL0212S05 IHL0212S09 IHL0212S12 IHL0212S15 IHL0212D05 IHL0212D09 IHL0212D12 IHL0212D15 IHL0212D1509 IHL0215S3V3 IHL0215S05 IHL0215S09 IHL0215S12 IHL0215S15 IHL0215D05 IHL0215D09 IHL0215D12 IHL0215D15 IHL0215D1509 IHL0224S3V3 IHL0224S05 IHL0224S09 IHL0224S12 IHL0224S15 IHL0224D05 IHL0224D09 IHL0224D12 IHL0224D15 IHL0224D1509 Notes Input currents measured at nominal input voltage. General Characteristic Efficiency Isolation: Input to Output Isolation Working Voltage Isolation Resistance Isolation Capacitance Switching Frequency Power Density Mean Time Between Failure Weight Minimum Typical 80 maximum 5200 250 109 7 100 23.7 50 3.3 0.006 (2.7) Units % VDC VAC Ω pF kHz W/in3 MHrs lb (g) www.xppower.com Notes & Conditions See Models and Ratings table MIL-HDBK-217F, +25 °C GB 2 IHL02 Series DC-DC Converter Environmental Characteristic maximum Units Operating Temperature Minimum -40 Typical +95 °C Storage Temperature -40 +125 °C Case Temperature 2.5 Humidity Notes & Conditions Derate Linearly from 100% at 65 °C to no load at 95 °C +100 °C 95 %RH Non-condensing Natural convection Cooling EMC: Emissions Phenomenon Standard Test Level Notes & Conditions Conducted EN55032 Class B See Application Note Radiated EN55032 Class B EMC: Immunity Phenomenon Standard Test Level Criteria ESD Immunity EN61000-4-2 ±6/±8 kV A Radiated Immunity EN61000-4-3 10 Vrms A EFT/Burst EN61000-4-4 2 kV A EN61000-4-6 10 V rms A EN61000-4-8 1 A/m A Conducted Immunity magnetic Fields Notes & Conditions Contact/Air Discharge External components required, see application notes Mechanical Details 0.28 (7.2) 0.76 (19.5) 0.12 (3.0) 0.37 (9.5) 0.02 (0.5) 0.10 (2.54) 0.01 Printed (0.25) Face 0.08 (2.0) 0.02 (0.5) 0.39 (10.0) 0.02 (0.5) 0.60 (15.24) 0.08 (2.13) 0.08 (2.13) Pin Connections Notes 1. All dimensions are in inches (mm) 2. Weight: 0.006 lbs (2.7 g) approx. 3. Pin diameter: 0.02±0.002 (0.5±0.05) 3 0.28 (7.2) 4. Pin pitch and length tolerance: ±0.014 (±0.35) 5. Case tolerance: ±0.02 (±0.5) www.xppower.com Pin 1 2 5 6 7 Single +Vin -Vin -Vout No Pin +Vout Dual +Vin -Vin -Vout Common +Vout 3 IHL02 Series DC-DC Converter Application Note Regulation Hig hl Typ ica Low imit l Lo ad L ine Lim it EFT Filter Input components C1 and D1 are used to help meet EFT and surge test requirements for the module. IHL02 D1 C1 D1 IHL0205XXXX 330 µF/50 V SMDJ9.0 A IHL0212XXXX 330 µF/50 V SMDJ13 A IHL0215XXXX 330 µF/50 V SMDJ18 A IHL0224XXXX 1000 µF/35 V SMDJ24 A EMI Filter Input filter components (C1,C2, C3 and L) are used to help meet conducted emissions requirements for the module. These components should be mounted as close as possible to the module, and all leads should be minimised to decrease radiated noise. C1 L C3 IHL02 L IHL0205XXXX 1206, 4.7 µF/ 16 V 6.8 µH IHL0212XXXX 1206, 22 µF/ 25 V 6.8 µH IHL0215XXXX 1206, 22 µF/ 25 V 6.8 µH IHL0224XXXX 1210, 10 µF/ 35 V 10 µH www.xppower.com C2 C3 1210, 10 µF/ 35 V 1210, 10 µF/ 35 V 23 Aug 16