Freescale Semiconductor, Inc.
Order this document
by MPX4115A/D
SEMICONDUCTOR TECHNICAL DATA
Freescale Semiconductor, Inc...
$"$ "##%" # "
" # %$ "##%"
$$" " " $" !!$ #
! $ !"$%"
!#$
"$
Motorola’s MPX4115A/MPXA4115A series sensor integrates on–chip, bipolar op amp
circuitry and thin film resistor networks to provide a high output signal and temperature
compensation. The small form factor and high reliability of on–chip integration make the
Motorola pressure sensor a logical and economical choice for the system designer.
The MPX4115A/MPXA4115A series piezoresistive transducer is a state–of–the–art,
monolithic, signal conditioned, silicon pressure sensor. This sensor combines advanced
micromachining techniques, thin film metallization, and bipolar semiconductor processing to
provide an accurate, high level analog output signal that is proportional to applied pressure.
Figure 1 shows a block diagram of the internal circuitry integrated on a pressure
sensor chip.
INTEGRATED
PRESSURE SENSOR
15 to 115 kPa (2.2 to 16.7 psi)
0.2 to 4.8 Volts Output
UNIBODY PACKAGE
Features
• 1.5% Maximum Error over 0° to 85°C
MPX4115A
CASE 867
• Ideally suited for Microprocessor or Microcontroller–
Based Systems
• Temperature Compensated from –40° to +125°C
• Durable Epoxy Unibody Element or Thermoplastic
(PPS) Surface Mount Package
Application Examples
SMALL OUTLINE PACKAGE
• Aviation Altimeters
• Industrial Controls
• Engine Control
• Weather Stations and Weather Reporting Devices
*'
(" !
(!$&()&
#!$"'(#"
"
" '( '"'"
!"(
"
" '( "
&#)"
&&"
'( &)(&-
*9>=
MPXA4115AC6U
CASE 482A
$"' " & "# #""('
#& '! #)( " $ *
$"' " & "# #""(' #&
)"#- *
Figure 1. Fully Integrated Pressure Sensor
Schematic
REV 4
Motorola Sensor Device Data
Motorola, Inc. 2001
MPX4115AP
CASE 867B
MPXA4115A6U
CASE 482
MPX4115AS
CASE 867E
PIN NUMBER
1
PIN NUMBER
N/C
5
N/C
1
Vout
4
N/C
2
VS
6
N/C
2
Gnd
5
N/C
3
Gnd
7
N/C
3
VS
6
N/C
4
Vout
8
N/C
NOTE: Pins 1, 5, 6, 7, and 8 are
internal device connections. Do not
connect to external circuitry or
ground. Pin 1 is noted by the notch in
the lead.
For More Information On This Product,
Go to: www.freescale.com
NOTE: Pins 4, 5, and 6 are internal
device connections. Do not connect
to external circuitry or ground. Pin 1
is noted by the notch in the lead.
1
Freescale
Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
MAXIMUM RATINGS(NOTE)
Parametrics
Units
Maximum Pressure (P1 P2)
Pmax
400
kPa
Storage Temperature
Tstg
–40° to +125°
°C
Operating Temperature
TA
–40° to +125°
°C
NOTE: Exposure beyond the specified limits may cause permanent damage or degradation to the device.
OPERATING CHARACTERISTICS (VS = 5.1 Vdc, TA = 25°C unless otherwise noted, P1 P2. Decoupling circuit shown in Figure 3
required to meet Electrical Specifications.)
Characteristic
Pressure Range
Supply
Voltage(1)
Symbol
Min
Typ
Max
Unit
POP
15
—
115
kPa
VS
4.85
5.1
5.35
Vdc
Io
—
7.0
10
mAdc
Freescale Semiconductor, Inc...
Supply Current
Minimum Pressure Offset(2)
@ VS = 5.1 Volts
(0 to 85°C)
Voff
0.135
0.204
0.273
Vdc
Full Scale Output(3)
@ VS = 5.1 Volts
(0 to 85°C)
VFSO
4.725
4.794
4.863
Vdc
Full Scale Span(4)
@ VS = 5.1 Volts
(0 to 85°C)
VFSS
4.521
4.590
4.659
Vdc
Accuracy(5)
(0 to 85°C)
—
—
—
±1.5
%VFSS
V/P
—
45.9
—
mV/kPa
Response Time(6)
tR
—
1.0
—
ms
Output Source Current at Full Scale Output
Io+
—
0.1
—
mAdc
—
—
20
—
ms
—
—
±0.5
—
%VFSS
Sensitivity
Warm–Up
Offset
Time(7)
Stability(8)
NOTES:
1. Device is ratiometric within this specified excitation range.
2. Offset (Voff) is defined as the output voltage at the minimum rated pressure.
3. Full Scale Output (VFSO) is defined as the output voltage at the maximum or full rated pressure.
4. Full Scale Span (VFSS) is defined as the algebraic difference between the output voltage at full rated pressure and the output voltage at the
minimum rated pressure.
5. Accuracy is the deviation in actual output from nominal output over the entire pressure range and temperature range as a percent of span
at 25°C due to all sources of error including the following:
• Linearity:
Output deviation from a straight line relationship with pressure over the specified pressure range.
• Temperature Hysteresis: Output deviation at any temperature within the operating temperature range, after the temperature is
cycled to and from the minimum or maximum operating temperature points, with zero differential
pressure applied.
• Pressure Hysteresis:
Output deviation at any pressure within the specified range, when this pressure is cycled to and from
minimum or maximum rated pressure at 25°C.
• TcSpan:
Output deviation over the temperature range of 0° to 85°C, relative to 25°C.
• TcOffset:
Output deviation with minimum pressure applied, over the temperature range of 0° to 85°C, relative
to 25°C.
6. Response Time is defined as the time for the incremental change in the output to go from 10% to 90% of its final value when subjected to
a specified step change in pressure.
7. Warm–up Time is defined as the time required for the product to meet the specified output voltage after the pressure has been stabilized.
8. Offset Stability is the product’s output deviation when subjected to 1000 cycles of Pulsed Pressure, Temperature Cycling with Bias Test.
MECHANICAL CHARACTERISTICS
Characteristics
Typ
Unit
Weight, Basic Element (Case 867)
4.0
grams
Weight, Small Outline Package (Case 482)
1.5
grams
2
For More Information On This Product,
Go to: www.freescale.com
Motorola Sensor Device Data
Freescale Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
*
)#&# ' #"
#(
'(" ''
'( $
$
+& #"
*9>=
*<
(&!#$ '(
'
&!
$'
'# )( !"(
#)($)(
"
:
#"
' *))! &&"
Figure 3. Recommended power supply decoupling
and output filtering.
For additional output filtering, please refer to
Application Note AN1646.
Figure 2 illustrates the absolute sensing chip in the basic
chip carrier (Case 482).
Figure 3 shows the recommended decoupling circuit for
interfacing the output of the integrated sensor to the A/D input of a microprocessor or microcontroller. Proper decoupling of the power supply is recommended.
#)($)(*96=<
!,
(&"'& )"(#"
*9>= *< $ ± ;;9;
*' *0/
(!$ =9 °
(-$
!"
Freescale Semiconductor, Inc...
Figure 2. Cross Sectional Diagram SOP
(not to scale)
$;1<<>;1 ;12 =9 <1.610 ?./>>7 48 5$.
Figure 4. Output versus Absolute Pressure
Figure 4 shows the sensor output signal relative to pressure input. Typical minimum and maximum output curves
are shown for operation over 0 to 85°C temperature range.
The output will saturate outside of the rated pressure range.
A fluorosilicone gel isolates the die surface and wire
bonds from the environment, while allowing the pressure
signal to be transmitted to the silicon diaphragm. The
Motorola Sensor Device Data
MPX4115A/MPXA4115A series pressure sensor operating
characteristics, internal reliability and qualification tests are
based on use of dry air as the pressure media. Media other
than dry air may have adverse effects on sensor performance and long–term reliability. Contact the factory for
information regarding media compatibility in your application.
For More Information On This Product,
Go to: www.freescale.com
3
Freescale
Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
Transfer Function (MPX4115A, MPXA4115A)
Nominal Transfer Value: Vout = VS x (0.009 x P – 0.095)
± (Pressure Error x Temp. Factor x 0.009 x VS)
VS = 5.1 ± 0.25 Vdc
Temperature Error Band
MPX4115A, MPXA4115A Series
;1.5 $948=<
#$
(17:1;.=>;1
;;9;
./=9;
(17:1;.=>;1 48 °
NOTE: The Temperature Multiplier is a linear response from 0°C to –40°C and from 85°C to 125°C
Pressure Error Band
;;9; 474=< 29; $;1<<>;1
$;1<<>;1;;9;5$.
Freescale Semiconductor, Inc...
'"&!$"! %
=9 $;1<<>;1 48 5$.
$;1<<>;1
A
=9
A
5$.
;;9; !.@
±A 5$.
ORDERING INFORMATION — UNIBODY PACKAGE
Device Type
Options
Case No.
MPX Series Order No.
Marking
Basic Element
Absolute, Element Only
867
MPX4115A
MPX4115A
Ported Elements
Absolute, Ported
867B
MPX4115AP
MPX4115AP
Absolute, Stove Pipe Port
867E
MPX4115AS
MPX4115A
ORDERING INFORMATION — SMALL OUTLINE PACKAGE
Device Type
Options
Case No.
Basic Element
Absolute, Element Only
482
MPXA4115A6U
Rails
MPXA4115A
Absolute, Element Only
482
MPXA4115A6T1
Tape and Reel
MPXA4115A
Absolute, Axial Port
482A
MPXA4115AC6U
Rails
MPXA4115A
Absolute, Axial Port
482A
MPXA4115AC6T1
Tape and Reel
MPXA4115A
Ported Element
4
MPX Series Order No.
Packing Options
For More Information On This Product,
Go to: www.freescale.com
Marking
Motorola Sensor Device Data
Freescale Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
INFORMATION FOR USING THE SMALL OUTLINE PACKAGE (CASE 482)
MINIMUM RECOMMENDED FOOTPRINT FOR SURFACE MOUNTED APPLICATIONS
Surface mount board layout is a critical portion of the total
design. The footprint for the surface mount packages must
be the correct size to ensure proper solder connection interface between the board and the package. With the correct
fottprint, the packages will self–align when subjected to a
solder reflow process. It is always recommended to design
boards with a solder mask layer to avoid bridging and shorting between solder pads.
Freescale Semiconductor, Inc...
(-$,
(-$,
(-$,
48/3
77
' Figure 5. SOP Footprint (Case 482)
Motorola Sensor Device Data
For More Information On This Product,
Go to: www.freescale.com
5
Freescale
Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
SMALL OUTLINE PACKAGE DIMENSIONS
–A–
D 8 PL
!
( '
"#('
!"'#"" " (# &"" $& "'
- ! #"(&# " !"'#" "
!"'#" " # "#( " ) !# $&#(&)'#"
!,!)! !# $&#(&)'#" *&( ')&' (-$ &(
'
–B–
G
S
N
Freescale Semiconductor, Inc...
H
C
J
–T–
PIN 1 IDENTIFIER
M
K
'
'
CASE 482–01
ISSUE O
–A–
D 8 PL
!
( '
"#('
!"'#"" " (# &"" $& "'
- ! #"(&# " !"'#" "
!"'#" " # "#( " ) !# $&#(&)'#"
!,!)! !# $&#(&)'#" *&( ')&' (-$ &(
'
N –B–
G
S
W
V
C
H
J
'
'
–T–
K
M
PIN 1 IDENTIFIER
CASE 482A–01
ISSUE A
6
For More Information On This Product,
Go to: www.freescale.com
Motorola Sensor Device Data
Freescale Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
UNIBODY PACKAGE DIMENSIONS
C
R
M
B
"#('
!"'#"" " (# &"" $& "'
- ! #"(&# " !"'#" "
!"'#" ' " )'* # ( !# '(#$ &" !# '(#$ &" "#( (# ,
POSITIVE PRESSURE
(P1)
–A–
N
PIN 1
L
–T–
G
J
S
F
D 6 PL
Freescale Semiconductor, Inc...
!
( '(- $" #$"
&#)"
*#)(
*')$$ *#)(
#$"
'(- $" *#)(
&#)"
*
*
*
*,
!
'
"#!
'
"#!
'(- $" #$"
&#)"
*#)(
*')$$ *#)(
#$"
CASE 867–08
ISSUE N
BASIC ELEMENT
T
"#('
!"'#"' & " ! !(&'
!"'#"' " (# &"' $& '!
- ! A
U
L
R
V
Q
N
Q
B
P
J
!
( %
K
S
PIN 1
P
C
!
G
6X
F
D
!
( $
'
%
'
CASE 867B–04
ISSUE
F F
'
'
'(- $" *#)(
&#)"
*
*
*
*,
PRESSURE SIDE PORTED (AP, GP)
Motorola Sensor Device Data
For More Information On This Product,
Go to: www.freescale.com
7
Freescale
Semiconductor, Inc.
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
UNIBODY PACKAGE DIMENSIONS—CONTINUED
C
"#('
!"'#"" " (# &"" $& "'
- ! #"(&# " !"'#" "
A
–B–
V
PIN 1
PORT #1
POSITIVE
PRESSURE
(P1)
K
J
Freescale Semiconductor, Inc...
N
S
G
F
E
D
6 PL
–T–
!
( !
'
'
'(- $" *#)(
&#)"
*
*
*
*,
CASE 867E–03
ISSUE D
PRESSURE SIDE PORTED (AS, GS)
8
For More Information On This Product,
Go to: www.freescale.com
Motorola Sensor Device Data
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
ARCHIVED BY FREESCALE SEMICONDUCTOR, INC. 2005
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental
damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application
by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are
not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where
personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application,
Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs,
damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated
with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the
part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217. 1–303–675–2140 or 1–800–441–2447
Technical Information Center: 1–800–521–6274
JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3–20–1,
Minami–Azabu. Minato–ku, Tokyo 106–8573 Japan. 81–3–3440–3569
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre,
2, Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong.
852–26668334
HOME PAGE: http://www.motorola.com/semiconductors/
Motorola Sensor Device Data
For More Information On This Product,
◊
Go to: www.freescale.com
9
MPX4115A/D