AD ADG709CRUZ Low voltage 4-/8-channel multiplexer Datasheet

CMOS, 1.8 V to 5.5 V/±2.5 V, 3 Ω
Low Voltage 4-/8-Channel Multiplexers
ADG708/ADG709
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAMS
1.8 V to 5.5 V single supply
±2.5 V dual supply
3 Ω on resistance
0.75 Ω on resistance flatness
100 pA leakage currents
14 ns switching times
Single 8-to-1 multiplexer ADG708
Differential 4-to-1 multiplexer ADG709
16-lead TSSOP package
Low power consumption
TTL-/CMOS-compatible inputs
Qualified for automotive applications
ADG708
S1
D
S8
APPLICATIONS
A1
A0
00041-001
1 OF 8
DECODER
A2 EN
Figure 1.
Data acquisition systems
Communication systems
Relay replacement
Audio and video switching
Battery-powered systems
ADG709
S1A
DA
GENERAL DESCRIPTION
S4A
The ADG708/ADG709 are low voltage, CMOS analog
multiplexers comprising eight single channels and four
differential channels, respectively. The ADG708 switches one of
eight inputs (S1 to S8) to a common output, D, as determined
by the 3-bit binary address lines A0, A1, and A2. The ADG709
switches one of four differential inputs to a common differential
output as determined by the 2-bit binary address lines A0 and
A1. An EN input on both devices is used to enable or disable
the device. When disabled, all channels are switched off.
Low power consumption and an operating supply range of
1.8 V to 5.5 V make the ADG708/ADG709 ideal for batterypowered, portable instruments. All channels exhibit breakbefore-make switching action preventing momentary shorting
when switching channels.
These switches are designed on an enhanced submicron process
that provides low power dissipation yet gives high switching
speed, very low on resistance, and leakage currents.
On resistance is in the region of a few ohms and is closely matched
between switches and very flat over the full signal range. These parts
can operate equally well as either multiplexers or demultiplexers
and have an input signal range that extends to the supplies.
S1B
DB
S4B
A0
A1
EN
00041-002
1 OF 4
DECODER
Figure 2.
PRODUCT HIGHLIGHTS
1.
2.
3.
4.
5.
Single-/dual-supply operation. The ADG708/ADG709 are
fully specified and guaranteed with 3 V and 5 V single-supply
and ±2.5 V dual-supply rails.
Low RON (3 Ω typical).
Low power consumption (<0.01 μW).
Guaranteed break-before-make switching action.
Small 16-lead TSSOP package.
The ADG708/ADG709 are available in a 16-lead TSSOP.
Rev. D
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks arethe property of their respectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700©2000–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com
ADG708/ADG709
Data Sheet
TABLE OF CONTENTS
Features .....................................................................................1
Truth Tables......................................................................... 11
Applications...............................................................................1
Typical Performance Characteristics ....................................... 12
General Description ..................................................................1
Test Circuits............................................................................. 15
Functional Block Diagrams .......................................................1
Terminology ............................................................................ 18
Product Highlights ....................................................................1
Applications Information ........................................................ 19
Revision History ........................................................................2
Power Supply Sequencing .................................................... 19
Specifications.............................................................................3
Outline Dimensions ................................................................ 20
Dual Supply ...........................................................................7
Ordering Guide ................................................................... 20
Absolute Maximum Ratings ......................................................9
Automotive Products........................................................... 20
ESD Caution ..........................................................................9
Pin Configurations and Function Descriptions .......................10
REVISION HISTORY
1/13−Rev. C to Rev. D
8/06−Rev. A to Rev. B
Changes to Ordering Guide .....................................................20
Updated Format ...........................................................Universal
Changes to Absolute Maximum Ratings Section....................... 9
Added Table 7 and Table 8....................................................... 10
Updated Outline Dimensions.................................................. 18
Changes to Ordering Guide..................................................... 18
4/09−Rev. B to Rev. C
Changes to Table 1.....................................................................3
Changes to Table 2.....................................................................5
Changes to Table 3.....................................................................7
Moved Truth Tables Section ....................................................11
Changes to Figure 7, Figure 8, and Figure 9.............................12
Changes to Figure 13 and Figure 14.........................................13
Moved Terminology Section....................................................18
Changes to Ordering Guide .....................................................20
4/02—Rev. 0 to Rev. A
Edits to Features and Product Highlights .................................. 1
Change to Specifications ....................................................... 2–4
Edits to Absolute Maximum Ratings Notes ............................... 5
Edits to TPCs 2, 5, 6–9, 11, and 15 ........................................ 7–9
Edits to Test Circuits 9 and 10 ................................................. 11
Addition of Test Circuit 11 ...................................................... 11
10/00—Revision 0: Initial Version
Rev. D | Page 2 of 20
Data Sheet
ADG708/ADG709
SPECIFICATIONS
VDD = 5 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 1.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match
Between Channels (ΔRON)
On Resistance Flatness
(RFLAT (ON))
+25°C
B Version
−40°C to −40°C to
+85°C
+125°C
0 V to
VDD
5
7
0.8
1.5
Drain Off Leakage, ID (Off )
±0.01
Channel On Leakage, ID, IS (On)
±0.01
4.5
0.4
1.65
±20
±20
±20
7
Ω max
Ω typ
0.8
1.5
Ω max
Ω typ
1.2
1.65
Ω max
±20
±20
nA typ
±0.1
±0.01
±0.3
±0.1
±0.01
±0.75
±0.1
±0.75
2.4
0.8
0.005
±1
±6
nA max
nA typ
nA max
nA typ
VIN = VINL or VINH
RL = 300 Ω, CL = 35 pF;
see Figure 24
VS1 = 3 V/0 V, VS8 = 0 V/3 V
RL = 300 Ω, CL = 35 pF
14
14
ns typ
Break-Before-Make Time
Delay, tOPEN
8
tON (EN)
14
tOFF (EN)
7
Charge Injection
±3
Off Isolation
−60
−80
25
25
ns max
ns typ
1
1
25
25
12
12
±3
ns min
ns typ
ns max
ns typ
ns max
pC typ
−60
−80
dB typ
dB typ
8
14
25
25
7
12
12
Rev. D | Page 3 of 20
VD = VS = 1 V or 4.5 V;
see Figure 23
±0.1
2
1
VD = 4.5 V/1 V, VS = 1 V/4.5 V;
see Figure 22
V min
V max
2
1
VDD = 5.5 V
VD = 4.5 V/1 V, VS = 1 V/4.5 V;
see Figure 21
2.4
0.8
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS1
tTRANSITION
25
VS = 0 V to VDD, IDS = 10 mA
VS = 0 V to VDD, IDS = 10 mA
nA max
μA typ
μA max
pF typ
25
VS = 0 V to VDD, IDS = 10 mA;
see Figure 20
±6
0.005
±0.1
Test Conditions/
Comments
V
5
±0.01
±20
Unit
Ω typ
0.75
1.2
±0.01
0 V to
VDD
3
0.75
LEAKAGE CURRENTS
Source Off Leakage, IS (Off)
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
0 V to
VDD
3
4.5
0.4
+25°C
C Version
−40°C to −40°C to
+85°C
+125°C
VS = 3 V; see Figure 25
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 26
RL = 300 Ω, CL = 35 pF
VS = 3 V; see Figure 26
VS = 2.5 V, RS = 0 Ω,
CL = 1 nF; See Figure 27
RL = 50 Ω, CL = 5 pF, f = 10 MHz
RL = 50 Ω, CL = 5 pF,
f = 1 MHz; see Figure 28
ADG708/ADG709
Data Sheet
B Version
−40°C to −40°C to
+85°C
+125°C
C Version
−40°C to −40°C to
+85°C
+125°C
−80
−80
dB typ
−3 dB Bandwidth
55
55
MHz typ
CS (Off )
CD (Off )
ADG708
ADG709
CD, CS (On)
ADG708
ADG709
POWER REQUIREMENTS
IDD
13
13
pF typ
Test Conditions/
Comments
RL = 50 Ω, CL = 5 pF,
f = 10 MHz
RL = 50 Ω, CL = 5 pF, f = 1 MHz;
see Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 30
f = 1 MHz
85
42
85
42
pF typ
pF typ
f = 1 MHz
f = 1 MHz
96
48
96
48
pF typ
pF typ
f = 1 MHz
f = 1 MHz
VDD = 5.5 V
Digital inputs = 0 V or 5.5 V
Parameter
Channel-to-Channel
Crosstalk
+25°C
−60
0.001
0.001
1.0
1
+25°C
−60
1.0
1.0
Guaranteed by design, not subject to production test.
Rev. D | Page 4 of 20
1.0
Unit
dB typ
μA typ
μA max
Data Sheet
ADG708/ADG709
VDD = 3 V ± 10%, VSS = 0 V, GND = 0 V, unless otherwise noted.
Table 2.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (ΔRON)
+25°C
B Version
−40°C to −40°C to
+85°C
+125°C
0 V to
VDD
8
11
0.4
±0.01
Drain Off Leakage, ID (Off )
±0.01
Channel On Leakage, ID, IS (On)
±0.01
0 V to
VDD
8
12
1.2
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
14
11
0.4
2
12
1.2
±20
±20
±20
±20
±20
±0.1
±0.01
±0.3
±0.1
±0.01
±0.75
±0.1
±0.75
2
±1
±6
Ω max
Ω typ
nA max
nA typ
nA max
nA typ
VIN = VINL or VINH
±0.1
RL = 300 Ω, CL = 35 pF;
see Figure 24
VS1 = 2 V/0 V, VS2 = 0 V/2 V
RL = 300 Ω, CL = 35 pF
18
ns typ
30
30
ns max
ns typ
1
1
30
30
15
15
Break-Before-Make Time
Delay, tOPEN
8
8
tON (EN)
18
tOFF (EN)
8
Charge Injection
±3
±3
ns min
ns typ
ns max
ns typ
ns max
pC typ
Off Isolation
−60
−60
dB typ
−80
−80
dB typ
−60
−60
dB typ
−80
−80
dB typ
55
55
MHz typ
18
30
8
15
Channel-to-Channel Crosstalk
−3 dB Bandwidth
30
15
Rev. D | Page 5 of 20
VS = VD = 1 V or 3 V;
see Figure 23
V min
V max
18
1
VS = 3 V/1 V, VD = 1 V/3 V;
see Figure 22
2.0
0.8
2
1
VDD = 3.3 V
VS = 3 V/1 V, VD = 1 V/3 V;
see Figure 21
nA max
2
30
VS = 0 V to VDD,
IDS = 10 mA
Ω max
μA typ
μA max
pF typ
30
VS = 0 V to VDD, IDS = 10 mA;
see Figure 20
±6
0.005
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 1
tTRANSITION
14
Test Conditions/
Comments
V
nA typ
2.0
0.8
0.005
Unit
Ω typ
±0.01
±20
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
+25°C
C Version
−40°C to −40°C to
+85°C
+125°C
VS = 2 V; see Figure 25
RL = 300 Ω, CL = 35 pF
VS = 2 V; see Figure 26
RL = 300 Ω, CL = 35 pF
VS = 2 V; see Figure 26
VS = 1.5 V, RS = 0 Ω,
CL = 1 nF; see Figure 27
RL = 50 Ω, CL = 5 pF,
f = 10 MHz
RL = 50 Ω, CL = 5 pF,
f = 1 MHz; see Figure 28
RL = 50 Ω, CL = 5 pF,
f = 10 MHz
RL = 50 Ω, CL = 5 pF,
f = 1 MHz; see Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 30
ADG708/ADG709
Parameter
CS (Off )
CD (Off )
ADG708
ADG709
CD, CS (On)
ADG708
ADG709
POWER REQUIREMENTS
IDD
Data Sheet
+25°C
13
B Version
−40°C to −40°C to
+85°C
+125°C
Unit
pF typ
Test Conditions/
Comments
f = 1 MHz
85
42
85
42
pF typ
pF typ
f = 1 MHz
f = 1 MHz
96
48
96
48
pF typ
pF typ
f = 1 MHz
f = 1 MHz
VDD = 3.3 V
Digital inputs = 0 V or 3.3 V
0.001
0.001
1.0
1
+25°C
13
C Version
−40°C to −40°C to
+85°C
+125°C
1.0
1.0
Guaranteed by design, not subject to production test.
Rev. D | Page 6 of 20
1.0
μA typ
μA max
Data Sheet
ADG708/ADG709
DUAL SUPPLY
VDD = 2.5 V ± 10%, VSS = –2.5 V ± 10%, GND = 0 V, unless otherwise noted.
Table 3.
Parameter
ANALOG SWITCH
Analog Signal Range
On Resistance (RON)
On Resistance Match Between
Channels (ΔRON)
On Resistance Flatness (RFLAT (ON))
+25°C
B Version
−40°C to −40°C to
+85°C
+125°C
VSS to VDD
2.5
4.5
0.4
5
7
0.8
1.5
1.65
Channel On Leakage, ID, IS (On)
±0.01
±20
±20
±20
±20
±20
Ω max
Ω typ
0.8
1.5
1.0
1.65
Ω max
Ω typ
Ω max
nA typ
±0.1
±0.01
±0.3
±0.1
±0.01
±0.75
±0.1
±0.75
1.7
0.7
0.005
±1
±6
nA max
nA typ
nA max
nA typ
RL = 300 Ω, CL = 35 pF;
see Figure 24
VS = 1.5 V/0 V; see Figure 24
RL = 300 Ω, CL = 35 pF
ns typ
25
25
ns max
ns typ
1
1
25
25
15
15
±3
ns min
ns typ
ns max
ns typ
ns max
pC typ
−60
−60
dB typ
−80
−80
dB typ
14
tOFF (EN)
8
Charge Injection
±3
Off Isolation
8
1
1
14
25
25
8
15
15
Rev. D | Page 7 of 20
VS = VD = +2.25 V/−1.25 V;
see Figure 23
VIN = VINL or VINH
14
tON (EN)
VS = +2.25 V/−1.25 V,
VD = −1.25 V/+2.25 V;
see Figure 22
±0.1
14
25
VDD = +2.75 V, VSS = −2.75 V
VS = +2.25 V/−1.25 V,
VD = −1.25 V/+2.25 V;
see Figure 21
V min
V max
2
25
VS = VSS to VDD, IDS = 10 mA
VS = VSS to VDD, IDS = 10 mA
1.7
0.7
2
8
VS = VSS to VDD, IDS = 10 mA;
see Figure 20
nA max
μA typ
μA max
pF typ
Break-Before-Make Time Delay,
tOPEN
Test Conditions/
Comments
±6
0.005
±0.1
Digital Input Capacitance, CIN
DYNAMIC CHARACTERISTICS 1
tTRANSITION
V
Ω typ
7
±0.01
±20
Unit
5
0.6
±0.01
±0.01
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current
IINL or IINH
4.5
0.4
0.6
Drain Off Leakage, ID (Off )
VSS to VDD
2.5
1.0
LEAKAGE CURRENTS
Source Off Leakage, IS (Off )
+25°C
C Version
−40°C to −40°C to
+85°C
+125°C
VS = 1.5 V; see Figure 25
RL = 300 Ω, CL = 35 pF
VS = 1.5 V; see Figure 26
RL = 300 Ω, CL = 35 pF
VS = 1.5 V; see Figure 26
VS = 0 V, RS = 0 Ω, CL = 1 nF;
see Figure 27
RL = 50 Ω, CL = 5 pF,
f = 10 MHz
RL = 50 Ω, CL = 5 pF,
f = 1 MHz; see Figure 28
ADG708/ADG709
Data Sheet
B Version
−40°C to −40°C to
+85°C
+125°C
C Version
−40°C to −40°C to
+85°C
+125°C
−80
−80
dB typ
−3 dB Bandwidth
55
55
MHz typ
CS (Off )
CD (Off )
ADG708
ADG709
CD, CS (On)
ADG708
ADG709
POWER REQUIREMENTS
IDD
13
13
pF typ
Test Conditions/
Comments
RL = 50 Ω, CL = 5 pF,
f = 10 MHz
RL = 50 Ω, CL = 5 pF,
f = 1 MHz; see Figure 29
RL = 50 Ω, CL = 5 pF;
see Figure 30
f = 1 MHz
85
42
85
42
pF typ
pF typ
f = 1 MHz
f = 1 MHz
96
48
96
48
pF typ
pF typ
f = 1 MHz
f = 1 MHz
VDD = 2.75 V
Digital inputs = 0 V or 2.75 V
Parameter
Channel-to-Channel Crosstalk
ISS
1
+25°C
−60
0.001
+25°C
−60
0.001
1.0
1.0
1.0
1.0
0.001
1.0
1.0
1.0
1.0
0.001
Guaranteed by design not subject to production test.
Rev. D | Page 8 of 20
Unit
dB typ
μA typ
μA max
μA typ
μA max
VSS = −2.75 V
Digital inputs = 0 V or 2.75 V
Data Sheet
ADG708/ADG709
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 4.
Parameter
VDD to VSS
VDD to GND
VSS to GND
Analog Inputs 1
Digital Inputs
1
Peak Current, S or D (Pulsed at 1 ms,
10% Duty Cycle Maximum)
Continuous Current, S or D
Operating Temperature
Industrial Temperature Range
Storage Temperature Range
Junction Temperature
TSSOP Package, Power Dissipation
θJA Thermal Impedance
θJC Thermal Impedance
Lead Temperature, Soldering
Vapor Phase (60 sec)
Infrared (15 sec)
Rating
7V
−0.3 V to +7 V
+0.3 V to −3.5 V
VSS − 0.3 V to VDD + 0.3 V
or 30 mA, whichever
occurs first
−0.3 V to VDD + 0.3 V or
30 mA, whichever
occurs first
100 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating can be applied at any one time.
ESD CAUTION
30 mA
−40°C to +125°C
−65°C to +150°C
150°C
432 mW
150.4°C/W
27.6°C/W
215°C
220°C
Overvoltages at A, EN, S, or D are clamped by internal codes. Current should
be limited to the maximum ratings given.
1
Rev. D | Page 9 of 20
ADG708/ADG709
Data Sheet
PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS
A0 1
16 A1
A0 1
16 A1
EN 2
15 A2
EN 2
15 GND
VSS
3
13 VDD
S1A
4
ADG709
12 S5
S2A
5
TOP VIEW
(Not to Scale)
6
11 S6
S3A
6
11 S3B
S4
7
10 S7
S4A
7
10 S4B
D
8
DA
8
4
ADG708
S2
5
TOP VIEW
(Not to Scale)
S3
9
S8
Figure 3. ADG708 Pin Configuration
14 V
DD
13 S1B
12 S2B
9
DB
00041-004
3
S1
00041-003
14 GND
VSS
Figure 4. ADG709 Pin Configuration
Table 5. ADG708 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
A0
EN
VSS
S1
S2
S3
S4
D
S8
S7
S6
S5
VDD
GND
A2
A1
Description
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 7).
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 7).
Most Negative Power Supply Pin in Dual-Supply Applications. For single-supply applications, it should be tied to GND.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Drain Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Most Positive Power Supply Pin.
Ground (0 V) Reference.
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 7).
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 7).
Table 6. ADG709 Pin Function Descriptions
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
A0
EN
VSS
S1A
S2A
S3A
S4A
DA
DB
S4B
S3B
S2B
S1B
VDD
GND
A1
Description
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 8).
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 8).
Most Negative Power Supply Pin in Dual-Supply Applications. For single-supply applications, it should be tied to GND.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Drain Terminal. Can be an input or output.
Drain Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Source Terminal. Can be an input or output.
Most Positive Power Supply Pin.
Ground (0 V) Reference.
Digital Input. Controls the configuration of the switch, as shown in the truth table (see Table 8).
Rev. D | Page 10 of 20
Data Sheet
ADG708/ADG709
TRUTH TABLES
Table 7. ADG708 Truth Table
A2
X1
0
0
0
0
1
1
1
1
1
A1
X1
0
0
1
1
0
0
1
1
A0
X1
0
1
0
1
0
1
0
1
EN
0
1
1
1
1
1
1
1
1
Switch Condition
None
1
2
3
4
5
6
7
8
X = Don’t care.
Table 8. ADG709 Truth Table
A1
X1
0
0
1
1
1
A0
X1
0
1
0
1
EN
0
1
1
1
1
On Switch Pair
None
1
2
3
4
X = Don’t care.
Rev. D | Page 11 of 20
ADG708/ADG709
Data Sheet
TYPICAL PERFORMANCE CHARACTERISTICS
8
8
TA = 25°C
VSS = 0V
7
VDD = 3V
VSS = 0V
7
+125°C
6
5
VDD = 3.3V
4
VDD = 4.5V
VDD = 5.5V
3
4
–40°C
3
2
2
1
1
0
1
2
3
4
VD OR VS – DRAIN OR SOURCE VOLTAGE (V)
5
+25°C
0
00041-005
0
+85°C
5
0
Figure 5. On Resistance as a Function of VD (VS) for Single Supply
0.5
1.0
1.5
2.0
2.5
VD OR VS – DRAIN OR SOURCE VOLTAGE (V)
3.0
00041-008
VDD = 2.7V
ON RESISTANCE (Ω)
ON RESISTANCE (Ω)
6
Figure 8. On Resistance as a Function of VD (VS) for Different Temperatures,
Single Supply
6
8
VDD = +2.5V
VSS = –2.5V
TA = 25°C
7
5
ON RESISTANCE (Ω)
5
4
VDD = +2.25V
VSS = –2.25V
3
+125°C
4
2
–40°C
2
1
VDD = +2.75V
VSS = –2.75V
0
–3.0 –2.5 –2.0 –1.5 –1.0 –0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
VD OR VS – DRAIN OR SOURCE VOLTAGE (V)
0
–2.5
00041-006
1
Figure 6. On Resistance as a Function of VD (VS) for Dual Supply
–2.0
–1.5
–1.0
–0.5
0
0.5
1.0
1.5
7
VDD = 5V
VSS = 0V
TA = 25°C
0.08
CURRENT (nA)
6
+125°C
4
+25°C
–2.5
Figure 9. On Resistance as a Function of VD (VS) for Different Temperatures,
Dual Supply
VDD = 5V
VSS = 0V
5
2.0
VD OR VS – DRAIN OR SOURCE VOLTAGE (V)
0.12
8
ON RESISTANCE (Ω)
+25°C
+85°C
3
00041-009
ON RESISTANCE (Ω)
6
+85°C
3
ID (ON)
0.04
0
IS (OFF)
–0.04
2
ID (OFF)
–0.08
–40°C
0
1
2
3
4
VD OR VS – DRAIN OR SOURCE VOLTAGE (V)
5
00041-007
–0.12
0
0
Figure 7. On Resistance as a Function of VD (VS) for Different Temperatures,
Single Supply
Rev. D | Page 12 of 20
1
3
2
VS, (VD = VDD – VS) (V)
4
Figure 10. Leakage Currents as a Function of VD (VS)
5
00041-010
1
Data Sheet
ADG708/ADG709
0.08
VDD = 3V
VSS = 0V
TA = 25°C
0.04
ID (ON)
0.35
VDD = +3V
0.30
0.25
CURRENT (nA)
CURRENT (nA)
0.12
0
IS (OFF)
–0.04
ID (OFF)
0.20
0.15
ID (ON)
0.10
0
0.5
2.5
1.0
1.5
2.0
VD, (VS = VDD – VD) (V)
3.0
0
00041-011
–0.12
0
40
80
60
100
120
Figure 14. Leakage Currents as a Function of Temperature
0.12
10m
VDD = +2.5V
VSS = –2.5V
TA = 25°C
0.08
TA = 25°C
1m
CURRENT (A)
0
IS (OFF)
–0.04
VDD = +2.5V
VSS = –2.5V
100µ
ID (ON), VS = VD
0.04
ID (OFF)
10µ
VDD = +5V
1µ
VDD = +3V
100n
–0.08
1.5
2.0
2.5
1n
10
00041-012
–0.12
0.5 1.0
–3.0 –2.5 –2.0 –1.5 –1.0 –0.5 0
VS, (VD = VDD – VS) (V)
3.0
100
1k
10k
100k
FREQUENCY (Hz)
1M
10M
00041-015
10n
Figure 15. Supply Current vs. Input Switching Frequency
Figure 12. Leakage Currents as a Function of VD (VS)
0
0.35
VDD = 5V
TA = 25°C
VDD = +5V
VSS = 0V
AND
VDD = +2.5V
VSS = –2.5V
0.25
–20
ATTENUATION (dB)
0.30
0.20
0.15
ID (OFF)
0.10
IS (OFF)
ID (ON)
0.05
40
60
80
100
120
TEMPERATURE (°C)
00041-013
20
–60
–80
–100
0
0
–40
–120
30k
100k
1M
FREQUENCY (Hz)
10M
Figure 16. Off Isolation vs. Frequency
Figure 13. Leakage Currents as a Function of Temperature
Rev. D | Page 13 of 20
100M
00041-016
CURRENT (nA)
20
TEMPERATURE (°C)
Figure 11. Leakage Currents as a Function of VD (VS)
CURRENT (nA)
ID (OFF)
IS (OFF)
0.05
00041-014
–0.08
ADG708/ADG709
Data Sheet
20
0
TA = 25°C
–40
0
–60
–20
–100
–30
100k
1M
FREQUENCY (Hz)
10M
100M
Figure 17. Crosstalk vs. Frequency
VDD = 5V
TA = 25°C
–10
–15
1M
FREQUENCY (Hz)
10M
100M
00041-018
ATTENUATION (dB)
–5
100k
–40
–3
VDD = +2.5V
VSS = –2.5V
–2
–1
0
1
2
VOLTAGE (V)
3
Figure 19. Charge Injection vs. Source Voltage
0
–20
30k
VDD = +3V
VSS = 0V
–10
–80
–120
30k
VDD = +5V
VSS = 0V
Figure 18. On Response vs. Frequency
Rev. D | Page 14 of 20
4
5
00041-019
10
QINJ (pC)
–20
00041-017
ATTENUATION (dB)
VDD = 5V
TA = 25°C
Data Sheet
ADG708/ADG709
TEST CIRCUITS
IDS
VDD
VSS
VDD
VSS
V1
S1
S
D
ID (OFF)
S2
D
A
S8
RON = V1/IDS
VD
VS
GND
Figure 20. On Resistance
IS(OFF)
0.8V
EN
Figure 22. ID (OFF)
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VSS
S1
A
ID (ON)
S1
D
S2
VS
00041-022
00041-020
VS
D
A
S8
VD
S8
GND
Figure 21. IS (OFF)
VIN
VSS
VDD
VSS
3V
S1
A1
50Ω
Figure 23. ID (ON)
VDD
A2
2.4V
EN
00041-023
GND
VS
00041-021
VD
0.8V
EN
ADDRESS
DRIVE (VIN)
VS1
50%
50%
0V
S2 TO S7
A0
2.4V
VS8
S8
VS1
EN
CL
35pF
RL
300Ω
GND
90%
VOUT
D
VOUT
90%
VS8
tTRANSITION
*SIMILAR CONNECTION FOR ADG709.
tTRANSITION
00041-024
ADG708*
Figure 24. Switching Time of Multiplexer, tTRANSITION
VDD
VSS
VDD
VIN
50Ω
3V
A2
VSS
S1
A1
S2 TO S7
ADDRESS
DRIVE (VIN)
VS
0V
A0
2.4V
S8
VOUT
D
EN
GND
RL
300Ω
CL
35pF
VOUT
80%
80%
tOPEN
*SIMILAR CONNECTION FOR ADG709.
Figure 25. Break-Before-Make Delay, tOPEN
Rev. D | Page 15 of 20
00041-025
ADG708*
ADG708/ADG709
Data Sheet
VDD
VDD
VSS
3V
VSS
ENABLE
DRIVE (VIN)
A2
VS
S1
tOFF (EN)
S2 TO S8
VO
ADG708*
EN
VIN
50%
0V
A1
A0
50%
VOUT
D
CL
35pF
RL
300Ω
GND
50Ω
0.9VO
0.9VO
OUTPUT
0V
00041-026
tON (EN)
*SIMILAR CONNECTION FOR ADG709.
Figure 26. Enable Delay, tON (EN), tOFF (EN)
VDD
A2 VDD
VSS
3V
VSS
LOGIC INPUT
(VIN)
0V
A1
RS
VS
ADG708*
D
S
CL VOUT
1nF
EN
VIN
ΔVOUT
VOUT
QINJ = CL × ΔVOUT
GND
00041-027
A0
*SIMILAR CONNECTION FOR ADG709.
Figure 27. Charge Injection
VDD
VSS
0.1µF
0.1µF
VDD
NETWORK
ANALYZER
VSS
A2
A1
S
50Ω
50Ω
A0
VS
D
2.4V
EN
RL
50Ω
OFF ISOLATION = 20 log
00041-028
GND
VOUT
VOUT
VS
Figure 28. Off Isolation
VSS
VDD
0.1µF
0.1µF
V
A2 DD
VSS
EN
A1
NETWORK
ANALYZER
50Ω
VS
50Ω
NETWORK
ANALYZER
D
S1
RL
50Ω
S2
S8
VOUT
GND
*SIMILAR CONNECTION FOR ADG709.
CHANNEL-TO-CHANNEL CROSSTALK = 20 log
VOUT
VS
Figure 29. Channel-to-Channel Crosstalk
Rev. D | Page 16 of 20
00041-029
A0
2.4V
ADG708*
Data Sheet
ADG708/ADG709
VSS
VDD
0.1µF
0.1µF
NETWORK
ANALYZER
VSS
VDD
A2
A1
S
50Ω
A0
VS
D
EN
RL
50Ω
GND
INSERTION LOSS = 20 log
VOUT WITH SWITCH
VOUT WITHOUT SWITCH
Figure 30. Bandwidth
Rev. D | Page 17 of 20
VOUT
00041-030
2.4V
ADG708/ADG709
Data Sheet
TERMINOLOGY
VDD
Most positive power supply potential.
VSS
Most negative power supply in a dual-supply application. In
single-supply applications, tie VSS to ground at the device.
GND
Ground (0 V) reference.
tON (EN)
Delay time between the 50% and 90% points of the EN digital
input and the switch on condition.
tOFF (EN)
Delay time between the 50% and 90% points of the EN digital
input and the switch off condition.
S
Source terminal. Can be an input or output.
D
Drain terminal. Can be an input or output.
tOPEN
Off time measured between the 80% points of both switches
when switching from one address state to another.
Ax
Logic control input.
Off Isolation
A measure of unwanted signal coupling through an off switch.
EN
Active high enable.
Crosstalk
A measure of unwanted signal that is coupled through from one
channel to another as a result of parasitic capacitance.
RON
Ohmic resistance between D and S.
RFLAT (ON)
Flatness is defined as the difference between the maximum and
minimum value of on resistance as measured over the specified
analog signal range.
IS (Off)
Source leakage current with the switch off.
Charge
A measure of the glitch impulse transferred from injection of
the digital input to the analog output during switching.
Bandwidth
The frequency at which the output is attenuated by 3 dB.
On Response
The frequency response of the on switch.
ID (Off)
Drain leakage current with the switch off.
On Loss
The loss due to the on resistance of the switch.
ID, IS (On)
Channel leakage current with the switch on.
VINL
Maximum input voltage for Logic 0.
VD (VS)
Analog voltage on Terminal D and Terminal S.
CS (Off)
Off switch source capacitance. Measured with reference to ground.
CD (Off)
Off switch drain capacitance. Measured with reference to ground.
CD, CS (On)
On switch capacitance. Measured with reference to ground.
CIN
Digital input capacitance.
tTRANSITION
Delay time measured between the 50% and 90% points of the
digital inputs and the switch on condition when switching from
one address state to another.
VINH
Minimum input voltage for Logic 1.
IINL (IINH)
Input current of the digital input.
IDD
Positive supply current.
ISS
Negative supply current.
Rev. D | Page 18 of 20
Data Sheet
ADG708/ADG709
APPLICATIONS INFORMATION
POWER SUPPLY SEQUENCING
When using CMOS devices, take care to ensure correct power
supply sequencing. Incorrect power supply sequencing can
result in the device being subjected to stresses beyond the
maximum ratings listed in Figure 4.
Always apply digital and analog inputs after power supplies and
ground. For single-supply operation, tie VSS to GND as close to
the device as possible.
Rev. D | Page 19 of 20
ADG708/ADG709
Data Sheet
OUTLINE DIMENSIONS
5.10
5.00
4.90
16
9
4.50
4.40
4.30
6.40
BSC
1
8
PIN 1
1.20
MAX
0.15
0.05
0.20
0.09
0.30
0.19
0.65
BSC
COPLANARITY
0.10
SEATING
PLANE
0.75
0.60
0.45
8°
0°
COMPLIANT TO JEDEC STANDARDS MO-153-AB
Figure 31. 16-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-16)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1, 2
ADG708BRU
ADG708BRU-REEL
ADG708BRU-REEL7
ADG708BRUZ
ADG708BRUZ-REEL
ADG708BRUZ-REEL7
ADG708CRU
ADG708CRU-REEL
ADG708CRUZ
ADG708CRUZ-REEL
ADG708CRUZ-REEL7
ADW54008-0REEL7
ADG709BRU
ADG709BRU-REEL
ADG709BRU-REEL7
ADG709BRUZ
ADG709BRUZ-REEL
ADG709BRUZ-REEL7
ADG709CRU-REEL7
ADG709CRUZ
ADG709CRUZ-REEL
ADG709CRUZ-REEL7
1
2
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
16-Lead Thin Shrink Small Outline
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
Package
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
[TSSOP]
Package Option
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
RU-16
Z = RoHS Compliant Part.
W = Qualified for Automotive Applications.
AUTOMOTIVE PRODUCTS
The ADW54008 models are available with controlled manufacturing to support the quality and reliability requirements of automotive
applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers
should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in
automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to
obtain the specific Automotive Reliability reports for these models.
©2000–2013 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D00041-0-1/13(D)
Rev. D | Page 20 of 20