September 2001 FDC6301N Dual N-Channel , Digital FET General Description Features These dual N-Channel logic level enhancement mode field effect transistors are produced using Fairchild 's proprietary, high cell density, DMOS technology. This very high density process is especially tailored to minimize on-state resistance. This device has been designed especially for low voltage applications as a replacement for digital transistors. Since bias resistors are not required, these N-Channel FET's can replace several digital transistors, with a variety of bias resistors. SOT-23 TM SuperSOT -8 TM SuperSOT -6 25 V, 0.22 A continuous, 0.5 A Peak. RDS(ON) = 5 Ω @ VGS= 2.7 V RDS(ON) = 4 Ω @ VGS= 4.5 V. Very low level gate drive requirements allowing direct operation in 3V circuits. VGS(th) < 1.5V. Gate-Source Zener for ESD ruggedness. >6kV Human Body Model. SO-8 SOIC-16 SOT-223 Mark: .301 INVERTER APPLICATION 4 3 5 2 6 1 Vcc D OUT Absolute Maximum Ratings G S GND TA = 25oC unless other wise noted Symbol Parameter VDSS, VCC Drain-Source Voltage, Power Supply Voltage VGSS, VIN Gate-Source Voltage, VIN ID, IOUT Drain/Output Current PD IN FDC6301N 25 - 0.5 to +8 - Continuous 0.22 - Pulsed 0.5 Maximum Power Dissipation (Note 1a) (Note 1b) TJ,TSTG Operating and Storage Temperature Range ESD Electrostatic Discharge Rating MIL-STD-883D Human Body Model (100pf / 1500 Ohm) 0.9 Units V V A W 0.7 -55 to 150 °C 6.0 kV THERMAL CHARACTERISTICS RθJA Thermal Resistance, Junction-to-Ambient (Note 1a) 140 °C/W RθJC Thermal Resistance, Junction-to-Case (Note 1) 60 °C/W © 2001 Fairchild Semiconductor Corporation FDC6301N Rev.D Electrical Characteristics (TA = 25 OC unless otherwise noted ) Symbol Parameter Conditions Min Typ Max Units OFF CHARACTERISTICS BVDSS Drain-Source Breakdown Voltage VGS = 0 V, ID = 250 µA ∆BVDSS/∆TJ Breakdown Voltage Temp. Coefficient ID = 250 µA, Referenced to 25 o C 25 IDSS Zero Gate Voltage Drain Current VDS = 20 V, VGS = 0 V IGSS Gate - Body Leakage Current VGS = 8 V, VDS= 0 V V mV /oC 25 TJ = 55°C 1 µA 10 µA 100 nA ON CHARACTERISTICS (Note 2) ∆VGS(th)/∆TJ Gate Threshold Voltage Temp.Coefficient ID = 250 µA, Referenced to 25 o C VGS(th) Gate Threshold Voltage VDS = VGS, ID = 250 µA RDS(ON) Static Drain-Source On-Resistance VGS = 2.7 V, ID = 0.2 A mV /oC -2.1 0.65 TJ =125°C VGS = 4.5 V, ID = 0.4 A 0.85 1.5 V 3.8 5 Ω 6.3 9 3.1 4 ID(ON) On-State Drain Current VGS = 2.7 V, VDS = 5 V gFS Forward Transconductance VDS = 5 V, ID= 0.4 A 0.25 S VDS = 10 V, VGS = 0 V, f = 1.0 MHz 9.5 pF 0.2 A DYNAMIC CHARACTERISTICS Ciss Input Capacitance Coss Output Capacitance Crss Reverse Transfer Capacitance 6 pF 1.3 pF SWITCHING CHARACTERISTICS (Note 2) tD(on) Turn - On Delay Time tr Turn - On Rise Time tD(off) Turn - Off Delay Time tf Turn - Off Fall Time Qg Total Gate Charge Qgs Gate-Source Charge Qgd Gate-Drain Charge VDD = 6 V, ID = 0.5 A, VGS = 4.5 V, RGEN = 50 Ω VDS = 5 V, ID = 0.2 A, VGS = 4.5 V 5 10 ns 4.5 10 ns 4 8 ns 3.2 7 ns 0.49 0.7 nC 0.22 nC 0.07 nC Inverter Electrical Characteristics (TA = 25°C unless otherwise noted) IO (off) Zero Input Voltage Output Current VCC = 20 V, VI = 0 V 1 µA VI (off) Input Voltage VCC = 5 V, IO = 10 µA 0.5 V VO = 0.3 V, IO = 0.005 A VI (on) RO (on) Output to Ground Resistance VI = 2.7 V, IO = 0.2 A 1 V 3.8 5 Ω Notes: 1. RθJA is the sum of the junction-to-case and case-to-ambient thermal resistance where the case thermal reference is defined as the solder mounting surface of the drain pins. RθJC is guaranteed by design while RθCA is determined by the user's board design. RθJA shown below for single device operation on FR-4 in still air. a. 140OC/W on a 0.125 in2 pad of 2oz copper. b. 180OC/W on a 0.005 in2 of pad of 2oz copper. 2. Pulse Test: Pulse Width < 300µs, Duty Cycle < 2.0%. FDC6301N Rev.D Typical Electrical Characteristics 3.5 R DS(on ) , NORMALIZED 3.0 0.4 2.7 2.5 0.3 0.2 2.0 0.1 1.5 I DRAIN-SOURCE ON-RESISTANCE 1.4 V GS = 4.5V D , DRAIN-SOURCE CURRENT (A) 0.5 VGS = 2.0V 1.2 2.5 0 1 V DS 2 3 4 , DRAIN-SOURCE VOLTAGE (V) 3.0 3.5 4.0 0.8 0.6 0 2.7 1 5 4.5 0 0.4 0.5 15 R DS(on) , ON-RESISTANCE (OHM) I D = 0.2A 1.6 V GS = 2.7 V 1.4 1.2 1 0.8 -25 0 25 50 75 100 TJ , JUNCTION TEMPERATURE (°C) 125 12 125°C 9 6 3 150 2 2.5 5 I S, REVERSE DRAIN CURRENT (A) V GS = 0V 0.15 0.1 0.05 Figure 5. Transfer Characteristics. 4.5 0.5 T = -55°C J 25°C 1 1.5 2 V GS , GATE TO SOURCE VOLTAGE (V) 4 Gate-To- Source Voltage. 125°C 0 0.5 3.5 Figure 4. On Resistance Variation with with Temperature. V DS = 5.0V 3 V GS , GATE TO SOURCE VOLTAGE (V) Figure 3. On-Resistance Variation 0.2 I D = 0.2A 25°C 0 0.6 -50 I D , DRAIN CURRENT (A) 0.3 Figure 2. On-Resistance Variation with Drain Current and Gate Voltage. 1.8 R DS(ON), NORMALIZED 0.2 ID , DRAIN CURRENT (A) Figure 1. On-Region Characteristics. DRAIN-SOURCE ON-RESISTANCE 0.1 2.5 0.2 0.1 TJ = 125°C 25°C 0.01 -55°C 0.001 0.0001 0.2 0.4 0.6 0.8 1 V SD , BODY DIODE FORWARD VOLTAGE (V) 1.2 Figure 6. Body Diode Forward Voltage Variation with Source Current and Temperature. FDC6301N Rev.D 5 30 VDS = 5V I D = 0.2A 20 10V 4 15V CAPACITANCE (pF) V GS , GATE-SOURCE VOLTAGE (V) Typical Electrical Characteristics (continued) 3 2 C iss 10 C oss 5 3 f = 1 MHz 2 1 0 V GS = 0V 1 0.1 0 0.1 0.2 0.3 0.4 0.5 C rss 0.5 0.6 1 2 5 10 25 V , DRAIN TO SOURCE VOLTAGE (V) DS Qg , GATE CHARGE (nC) Figure 8. Capacitance Characteristics. Figure 7. Gate Charge Characteristics. 1 5 1m 10 s ms IT LIM N) (O S RD 10 0m s 1s 0.1 DC 0.05 0.02 V GS = 2.7V SINGLE PULSE RθJA =See note 1b TA = 25°C 0.01 0.5 1 DS 3 2 1 2 V SINGLE PULSE RθJA =See note 1b TA = 25°C 4 POWER (W) 0.2 5 10 15 25 0 0.01 35 0.1 1 10 100 300 SINGLE PULSE TIME (SEC) , DRAI N-SOURCE VOLTAGE (V) Figure 10. Single Pulse Maximum Power Dissipation. Figure 9. Maximum Safe Operating Area. 1 r(t), NORMALIZED EFFECTIVE TRANSIENT THERMAL RESISTANCE ID , DRAIN CURRENT (A) 0.5 0.5 D = 0.5 0.2 0.2 0.1 0.05 0.02 0.01 0.0001 RθJA (t) = r(t) * R θJA R θJA = See Note 1b 0.1 P(pk) 0.05 t1 0.02 0.01 Single Pulse 0.001 t2 TJ - TA = P * R JA(t) θ Duty Cycle, D = t 1/ t 2 0.01 0.1 1 10 100 300 t 1, TIME (sec) Figure 11. Transient Thermal Response Curve. Note: Thermal characterization performed using the conditions described in note 1b.Transient thermal response will change depending on the circuit board design. FDC6301N Rev.D TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. ACEx Bottomless CoolFET CROSSVOLT DenseTrench DOME EcoSPARK E2CMOSTM EnSignaTM FACT FACT Quiet Series FAST â FASTr FRFET GlobalOptoisolator GTO HiSeC I2C ISOPLANAR LittleFET MicroFET MicroPak MICROWIRE OPTOLOGIC â OPTOPLANAR PACMAN POP Power247 PowerTrench â QFET QS QT Optoelectronics Quiet Series SILENT SWITCHER â UHC SMART START UltraFET â SPM VCX STAR*POWER Stealth SuperSOT-3 SuperSOT-6 SuperSOT-8 SyncFET TinyLogic TruTranslation STAR*POWER is used under license DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component is any component of a life 1. Life support devices or systems are devices or support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. H5