GE MPG06J Miniature glass passivated junction plastic rectifier Datasheet

MPG06A THRU MPG06M
MINIATURE GLASS PASSIVATED JUNCTION PLASTIC RECTIFIER
Reverse Voltage - 50 to 1000 Volts
Forward Current - 1.0 Ampere
FEATURES
Case Style MPG06
0.100 (2.54)
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ Low forward voltage, high current capability
♦ Glass passivated chip junction
♦ High surge capability
♦ Typical IR less than 0.1µA
♦ High temperature soldering guaranteed:
250°C/10 seconds, 0.375" (9.5mm) lead length,
5 lbs. (2.3kg) tension
1.0 (25.4)
MIN.
0.090 (2.29)
DIA
0.125 (3.18)
0.115 (2.92)
MECHANICAL DATA
1.0 (25.4)
MIN.
Case: Molded plastic over passivated chip
Terminals: Plated axial leads, solderable per MIL-STD-750,
Method 2026
Polarity: Color band denotes cathode end
Mounting Position: Any
Weight: 0.0064 ounce, 0.181 gram
0.025 (0.635)
0.023 (0.584)
DIA.
Dimensions are in inches and (millimeters)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
SYMBOLS
MPG
06A
MPG
06B
MPG
06D
MPG
06G
MPG
06J
MPG
06K
MPG
06M
UNITS
Maximum repetitive peak reverse voltage
VRRM
50
100
200
400
600
800
1000
Volts
Maximum RMS voltage
VRMS
35
70
140
280
420
560
700
Volts
Maximum DC blocking voltage
VDC
50
100
200
400
600
800
1000
Volts
Maximum average forward rectified current
0.375" (9.5mm) lead length at TA=25°C
I(AV)
1.0
Amp
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
IFSM
40.0
Amps
VF
1.1
Volts
Maximum instantaneous forward voltage at 1.0A
Maximum DC reverse current
at rated DC blocking voltage
TA=25°C
TA=125°C
IR
5.0
50.0
µA
Typical junction capacitance
(NOTE 1)
CJ
10.0
pF
Typical reverse recovery time
(NOTE 2)
trr
0.6
µs
RΘJA
RΘJL
67.0
30.0
°C/W
TJ, TSTG
-55 to +150
°C
Typical thermal resistance
(NOTE 3)
Operating junction and storage temperature range
NOTES:
(1) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts
(2) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(3) Thermal resistance from junction to ambient and from junction to lead at 0.375" (9.5mm) lead length,
P.C.B. mounted with 0.22 x 0.22” (5.5 x 5.5mm) copper pads
4/98
RATINGS AND CHARACTERISTIC CURVES MPG06A THRU MPG06M
FIG. 2 - MAXIMUM NON-REPETITIVE PEAK
FORWARD SURGE CURRENT
FIG. 1 - FORWARD CURRENT DERATING CURVE
60 HZ RESISTIVE OR
INDUCTIVE LOAD
0.375" (9.5mm) LEAD
LENGTH
1.0
PEAK FORWARD SURGE CURRENT,
AMPERES
AVERAGE FORWARD RECTIFIED
CURRENT, AMPERES
1.2
0.8
0.6
0.4
CAPACITANCE
LOADS
5.0
Ipk/IAV = 10
20
0.2
0
0
25
50
75
50
40
NO LOAD CONDITION
30
RATED LOAD
20
10
0
100 125 150 175
TJ=TJ max.
8.3ms SINGLE HALF SINE-WAVE
(JEDEC Method)
1
AMBIENT TEMPERATURE, °C
FIG. 3 - TYPICAL INSTANTANEOUS
FORWARD CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
10
INSTANTANEOUS FORWARD CURRENT,
AMPERES
100
FIG. 4 - TYPICAL REVERSE CHARACTERISTICS
30
TJ=150°C
1
10
NUMBER OF CYCLES AT 60 HZ
TJ=25°C
PULSE WIDTH=300µs
1% DUTY CYCLE
10
TJ=125°C
1
TJ=75°C
0.1
TJ=25°C
0.01
0
0.1
20
40
80
60
100
PERCENT OF RATED PEAK REVERSE
VOLTAGE, %
0.01
0.4
0.6
0.8
1.0
1
1.2
1.4
1.6
1.8
INSTANTANEOUS FORWARD VOLTAGE,
VOLTS
JUNCTION CAPACITANCE, pF
30
TJ=25°C
f=1.0 MHZ
Vsig=50mVp-p
10
1
1
10
REVERSE VOLTAGE, VOLTS
100
FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE
TRANSIENT THERMAL IMPEDANCE, °C/W
FIG. 5 - TYPICAL JUNCTION CAPACITANCE
100
10
1
0.1
0.01
0.1
1
10
t, PULSE DURATION, sec.
100
Similar pages