SMT inductors SIMID series, SIMID 1210-T Series/Type: B82422T Date: October 2012 a~í~=pÜÉÉí ¤EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS’ prior express consent is prohibited. SMT inductors, SIMID series B82422T SIMID 1210-T Size 1210 (EIA) or 3225 (IEC) Rated inductance 0.010 ... 100 μH Rated current 60 ... 450 mA Construction ■ Ceramic or ferrite core ■ Laser-welded winding ■ Flame-retardant molding Features ■ ■ ■ ■ ■ High Q factor High resonance frequency High L value Qualified to AEC-Q200 Suitable for lead-free reflow soldering as referenced in JEDEC J-STD 020D ■ RoHS-compatible Applications ■ ■ ■ ■ ■ ■ Filtering of supply voltages, coupling, decoupling Antenna systems Automotive electronics Telecommunications Consumer and data processing equipment Industrial electronics Terminals ■ Base material CuSn6 ■ Layer composition Cu, Ag, Sn (lead-free)1) ■ Electro-plated Marking ■ Marking on component: Manufacturer and letter “T”, L value (in PH), tolerance of L value (coded), date of manufacture (YWWD) ■ Minimum data on reel: Manufacturer, ordering code, L value, quantity, date of packing Delivery mode and packing units ■ 8-mm blister tape, wound on 180-mm or 330-mm reel ■ Packing units: 180-mm reel: 2000 pcs./reel 330-mm reel: 8000 pcs./reel 1) Ni-barrier-plated terminals (NiSn) on request (B82422T*50). Please read Cautions and warnings and Important notes at the end of this document. 2 10/12 SMT inductors, SIMID series B82422T SIMID 1210-T Dimensional drawing and layout recommendation 2±0.11) A 0.5±0.2 1) B C D B IND0053-6 2±0.1 0.4 min.1) 3.2+0.3 2.5+0.3 0.15 max. A B C D 2.7 1.15 2.1 4.4 Marking 1) Soldering area Dimensions in mm IND0073-6-E Taping and packing Reel <_ 2.6 4±0.1 _0 12.75 +0.15 _2 330 +0 8±0.3 2±0.05 _2 180 +0 1.5+0.1 <_ 4.2 Component 14.4 max. 3.5±0.05 4±0.1 1.75±0.1 Blister tape _0 8.4 +1.5 1.0+0.2 62±1.5 IND0592-V Direction of unreeling IND0559-Z-E Dimensions in mm Please read Cautions and warnings and Important notes at the end of this document. 3 10/12 SMT inductors, SIMID series B82422T SIMID 1210-T Technical data and measuring conditions Rated inductance LR Measured with impedance analyzer Agilent 4294A at frequency fL, 0.1 V, +20 °C Q factor Qmin Measured with impedance analyzer Agilent 4294A at frequency fQ, +20 °C Rated temperature TR +85 qC Rated current IR Maximum permissible DC with inductance decrease 'L/L0 d 10% and temperature increase of d 30 K at rated temperature Self-resonance frequency fres,min Measured with impedance analyzer Agilent E4991A / network analyzer Agilent E8362B, +20 °C DC resistance Rmax Measured at +20 qC Solderability (lead-free) Sn95.5Ag3.8Cu0.7: +(245 r5) °C, (5 r0.3) s Wetting of soldering area t 90% (based on IEC 60068-2-58) Resistance to soldering heat +260 qC, 40 s (as referenced in JEDEC J-STD 020D) Climatic category 55/125/56 (to IEC 60068-1) Storage conditions Mounted: –55 °C … +125 °C Packaged: –25 °C … +40 °C, d 75% RH Weight Approx. 50 mg Please read Cautions and warnings and Important notes at the end of this document. 4 10/12 SMT inductors, SIMID series B82422T SIMID 1210-T Characteristics and ordering codes fL ; fQ IR Rmax fres,min MHz mA : MHz Ordering code 1)2) ( 180-mm reel) 15 100 450 0.10 4000 B82422T3100+000 17 100 450 0.11 3500 B82422T3120+000 0.015 19 100 450 0.13 3000 B82422T3150+000 0.018 21 100 450 0.14 2000 B82422T3180+000 0.022 23 100 450 0.16 2000 B82422T3220+000 0.027 23 100 450 0.17 1700 B82422T3270+000 0.033 25 100 450 0.18 1700 B82422T3330+000 0.039 25 100 450 0.19 1300 B82422T3390+000 0.047 26 100 450 0.20 1300 B82422T3470+000 0.056 26 100 450 0.21 1100 B82422T3560+000 0.068 27 100 450 0.23 1000 B82422T3680+000 0.082 27 100 450 0.26 1000 B82422T3820+000 0.10 28 100 450 0.31 900 B82422T3101+000 LR Tolerance Qmin PH Core material: ceramic 0.010 r5% 0.012 r10% ^ J ^ K Core material: ferrite 0.12 r5% 0.15 r10% 30 25.2 450 0.15 900 B82422T1121+000 30 25.2 450 0.18 700 B82422T1151+000 0.18 30 25.2 450 0.19 500 B82422T1181+000 0.22 30 25.2 450 0.20 500 B82422T1221+000 0.27 30 25.2 450 0.21 500 B82422T1271+000 0.33 30 25.2 450 0.23 500 B82422T1331+000 0.39 30 25.2 450 0.25 400 B82422T1391+000 0.47 30 25.2 450 0.30 400 B82422T1471+000 0.56 30 25.2 450 0.31 300 B82422T1561+000 0.68 30 25.2 450 0.34 300 B82422T1681+000 0.82 30 25.2 450 0.38 300 B82422T1821+000 1.0 30 7.96 400 0.6 300 B82422T1102+000 1.2 30 7.96 390 0.7 250 B82422T1122+000 ^ J ^ K Closer tolerances and special versions on request. Higher currents possible at temperatures <TR on request. Sample kit available. Ordering code: B82422X001 For more information refer to chapter “Sample kits”. 1) Replace the + by the code letter for the required inductance tolerance. For reel size 330 mm the last digit has to be an »8«. Example: B82422T3100K008 2) For Ni-barrier-plated terminals replace the last two digits “00” by “50” (reel 180 mm) or “58” (reel 330 mm). Please read Cautions and warnings and Important notes at the end of this document. 5 10/12 SMT inductors, SIMID series B82422T SIMID 1210-T Characteristics and ordering codes Tolerance Qmin Ordering code 1)2) ( 180-mm reel) fL ; fQ IR Rmax fres,min MHz mA : MHz 30 7.96 370 0.7 200 B82422T1152+000 30 7.96 350 0.8 140 B82422T1182+000 2.2 30 7.96 320 0.8 100 B82422T1222+000 2.7 30 7.96 290 0.9 70 B82422T1272+000 3.3 30 7.96 260 1.2 60 B82422T1332+000 3.9 30 7.96 250 1.3 60 B82422T1392+000 4.7 30 7.96 220 1.5 50 B82422T1472+000 5.6 27 7.96 200 1.6 45 B82422T1562+000 6.8 27 7.96 180 1.8 40 B82422T1682+000 8.2 27 7.96 170 2.0 35 B82422T1822+000 10 27 2.52 150 2.1 30 B82422T1103+000 12 27 2.52 140 2.5 25 B82422T1123+000 15 27 2.52 130 2.8 20 B82422T1153+000 18 27 2.52 120 3.0 20 B82422T1183+000 22 27 2.52 110 3.5 20 B82422T1223+000 27 27 2.52 80 4.5 20 B82422T1273+000 33 27 2.52 70 5.6 17 B82422T1333+000 39 27 2.52 65 6.4 16 B82422T1393+000 47 27 2.52 60 7.0 15 B82422T1473+000 56 27 2.52 60 8.0 12 B82422T1563+000 68 27 2.52 60 9.0 9 B82422T1683+000 82 25 2.52 60 10 9 B82422T1823+000 100 20 0.796 60 11 8 B82422T1104+000 LR PH 1.5 r5% 1.8 r10% ^ J ^ K Closer tolerances and special versions on request. Higher currents possible at temperatures <TR on request. Sample kit available. Ordering code: B82422X001 For more information refer to chapter “Sample kits”. 1) Replace the + by the code letter for the required inductance tolerance. For reel size 330 mm the last digit has to be an »8«. Example: B82422T1104K008 2) For Ni-barrier-plated terminals replace the last two digits “00” by “50” (reel 180 mm) or “58” (reel 330 mm). Please read Cautions and warnings and Important notes at the end of this document. 6 10/12 SMT inductors, SIMID series B82422T SIMID 1210-T Inductance L versus DC load current IDC measured with LCR meter Agilent 4285A, typical values at +20 °C Impedance |Z| versus frequency f measured with impedance analyzer Agilent E4991A, typical values at +20 °C IND0074-8 10 5 Ω |Z | B82422T L 10 3 10 1 10 2 10 0 10 100 μH 10 μH 1 μH 100 nH 10 nH 10 0 10 _1 10 6 10 7 10 8 10 Hz 10 9 f 1 μH _1 0.1 μH _2 0.01 μH _3 _2 10 _1 10 0 A 10 1 I DC Current derating Iop/IR versus ambient temperature TA (rated temperature TR = +85 °C) IND0076-9 IND0077-H-E 1.2 B82422T I op IR 90 80 70 B82422T 1.0 0.8 60 0.01 μH 0.1 μH 50 40 10 μH 10 Q factor versus frequency f measured with impedance analyzer Agilent E4991A, typical values at +20 °C 100 100 μH 10 2 10 1 Q B82422T μH 10 4 10 IND0075-W 10 3 0.6 0.12 μH 1 μH 10 μH 30 100 μH 0.4 20 0.2 10 0 5 10 10 6 10 7 10 8 0 Hz 10 9 f 0 20 40 60 80 100 ˚C TA 7 10/12 140 Cautions and warnings ■ Please note the recommendations in our Inductors data book (latest edition) and in the data sheets. – Particular attention should be paid to the derating curves given there. – The soldering conditions should also be observed. Temperatures quoted in relation to wave soldering refer to the pin, not the housing. ■ If the components are to be washed varnished it is necessary to check whether the washing varnish agent that is used has a negative effect on the wire insulation, any plastics that are used, or on glued joints. In particular, it is possible for washing varnish agent residues to have a negative effect in the long-term on wire insulation. Washing processes may damage the product due to the possible static or cyclic mechanical loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts, which might lead to reduced reliability or lifetime. ■ The following points must be observed if the components are potted in customer applications: – Many potting materials shrink as they harden. They therefore exert a pressure on the plastic housing or core. This pressure can have a deleterious effect on electrical properties, and in extreme cases can damage the core or plastic housing mechanically. – It is necessary to check whether the potting material used attacks or destroys the wire insulation, plastics or glue. – The effect of the potting material can change the high-frequency behaviour of the components. ■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to breakage of the core. ■ Even for customer-specific products, conclusive validation of the component in the circuit can only be carried out by the customer. Please read Cautions and warnings and Important notes at the end of this document. 8 10/12 Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 9 10/12