Type 632P Vishay Sprague Film Capacitors Metalized Polycarbonate, Wrap-and-Fill FEATURES • Superior performance • High efficiency • High stability • High reliability • Rugged construction • Small size PERFORMANCE CHARACTERISTICS DC Life Test: 140% of rated voltage for 250 hours @ + 125°C. No open or short circuits. No visible damage. Maximum ∆ CAP ± 5%. Minimum IR = 30% of initial limit. Maximum DF = 0.5%. Humidity Test: 95% relative humidity @ + 40°C for 240 hours. No visible damage. Maximum ∆ CAP ± 5%. Minimum IR = 50% of initial limit. Maximum DF = 0.5%. Operating Temperature: - 55°C to + 125°C. Capacitance Range: 0.001µF to 10.0µF. Capacitance Tolerance: ± 10%, ± 5%, ± 2%. DC Voltage Rating: 50 WVDC to 400 WVDC. AC Voltage Rating: See AC Voltage Rating table. Dissipation Factor: 0.25% maximum. Voltage Test: 200% of rated voltage for 1 minute. Insulation Resistance: At + 25°C: 50,000 Megohm - Microfarads, or 100,000 Megohm minimum. At + 85°C: 2,000 Megohm - Microfarads, or 4000 Megohm minimum. At + 125°C: 250 Megohm - Microfarads or 500 Megohm minimum Vibration Test (Condition D): No mechanical damage. No short, open or intermittent circuits. PHYSICAL CHARACTERISTICS Lead Pull: 5 pounds (2.3 kilograms) for one minute. No physical damage. Lead Bend: After three complete consecutive bends, no damage. Marking: Sprague® trademark, type or part number, capacitance and voltage. DIMENSIONS in inches [millimeters] L 1.625 [41.27] Min. ± 0.040 [1.02] D Max. 1.625 [41.27] Min. Solid Tinned Wire* * Leads to be within ± 0.062" [1.57mm] of center line at egress but not less than 0.031" [0.79mm] from edge. AC VOLTAGE RATING (- 55°C to + 105°C Ambient) EQUIVALENT VAC rms RATINGS @ DC VOLTAGE RATING 400Hz 800Hz 1200Hz 1600Hz 2000Hz 50 (0.33µF through 5.6µF) (6.8µF through 10.0µF) 25.0 20.0 20.0 18.0 15.0 12.0 12.0 10.0 10.0 8.0 100 (0.15µF through 5.0µF) (6.8µF through 12.0µF) 65.0 40.0 45.0 30.0 35.0 25.0 30.0 20.0 25.0 18.0 200 (0.056µF through 2.0µF) (2.2µF through 5.0µF) 120.0 95.0 85.0 65.0 65.0 55.0 55.0 45.0 50.0 40.0 400 (0.022µF through 1.2µF) (1.5µF through 2.0µF) 200.0 165.0 140.0 110.0 115.0 90.0 100.0 80.0 90.0 70.0 Document Number: 42028 Revision 04-Dec-03 For technical questions, contact [email protected] www.vishay.com 83 Type 632P Vishay Sprague STANDARD RATINGS in inches [millimeters] CASE SIZE CAPACITANCE (µF) PART NUMBER** L LEAD AWG NO. 0.01* 632P103X9050 D 50 WVDC 0.170 [4.32] 0.440 [11.18] 24 0.012 632P123X9050 0.170 [4.32] 0.440 [11.18] 24 0.015 632P153X9050 0.170 [4.32] 0.440 [11.18] 24 0.018 632P183X9050 0.170 [4.32] 0.440 [11.18] 24 0.02 632P203X9050 0.170 [4.32] 0.440 [11.18] 24 0.022* 632P223X9050 0.170 [4.32] 0.440 [11.18] 24 0.027 632P273X9050 0.170 [4.32] 0.440 [11.18] 24 0.033* 632P333X9050 0.170 [4.32] 0.440 [11.18] 24 0.039 632P393X9050 0.170 [4.32] 0.440 [11.18] 24 0.047* 632P473X9050 0.170 [4.32] 0.440 [11.18] 24 0.056 632P563X9050 0.170 [4.32] 0.440 [11.18] 24 0.068 632P683X9050 0.170 [4.32] 0.560 [14.22] 24 0.082 632P823X9050 0.170 [4.32] 0.560 [14.22] 24 0.10* 632P104X9050 0.190 [4.83] 0.560 [14.22] 24 0.12 632P124X9050 0.190 [4.83] 0.560 [14.22] 24 0.15* 632P154X9050 0.230 [5.84] 0.440 [11.18] 22 0.18 632P184X9050 0.230 [5.84] 0.560 [14.22] 22 0.2 632P204X9050 0.230 [5.84] 0.560 [14.22] 22 0.22* 632P224X9050 0.230 [5.84] 0.560 [14.22] 22 0.27 632P274X9050 0.230 [5.84] 0.560 [14.22] 22 0.33* 632P334X9050 0.250 [6.35] 0.560 [14.22] 22 0.39 632P394X9050 0.250 [6.35] 0.560 [14.22] 22 0.47* 632P474X9050 0.310 [7.87] 0.560 [14.22] 22 0.50 632P504X9050 0.310 [7.87] 0.560 [14.22] 22 0.56 632P564X9050 0.310 [7.87] 0.560 [14.22] 22 0.68* 632P684X9050 0.310 [7.87] 0.560 [14.22] 22 0.82 632P824X9050 0.270 [6.86] 0.750 [19.05] 22 1.0* 632P105X9050 0.310 [7.87] 0.750 [19.05] 22 1.2 632P125X9050 0.350 [8.89] 0.750 [19.05] 20 1.5* 632P155X9050 0.350 [8.89] 0.750 [19.05] 20 1.8 632P185X9050 0.370 [9.40] 0.750 [19.05] 20 2.0* 632P205X9050 0.400 [10.16] 0.750 [19.05] 20 2.2* 632P225X9050 0.400 [10.16] 0.750 [19.05] 20 2.7 632P275X9050 0.400 [10.16] 1.000 [25.40] 20 3.0 632P305X9050 0.400 [10.16] 1.000 [25.40] 20 3.3 632P335X9050 0.400 [10.16] 1.000 [25.40] 20 3.9 632P395X9050 0.400 [10.16] 1.250 [31.75] 20 4.7* 632P475X9050 0.450 [11.43] 1.250 [31.75] 20 5.0 632P505X9050 0.500 [12.70] 1.250 [31.75] 20 5.6 632P565X9050 0.550 [13.97] 1.000 [25.40] 20 6.0 632P605X9050 0.550 [13.97] 1.000 [25.40] 20 6.8 632P685X9050 0.600 [15.24] 1.000 [25.40] 20 8.0 632P825X9050 0.550 [12.70] 1.310 [33.27] 20 10.0* 632P106X9050 0.600 [15.24] 1.310 [33.27] 20 * These ratings are stocked. ** Part Numbers listed are for a capacitance tolerance of ± 10%. To specify ± 5% tolerance, change the "X9" in the Part Number to "X5"; for ± 2%, from "X9" to "X2". www.vishay.com 84 For technical questions, contact [email protected] Document Number: 42028 Revision 04-Dec-03 Type 632P Vishay Sprague STANDARD RATINGS in inches [millimeters] CASE SIZE CAPACITANCE (µF) PART NUMBER* 0.01 0.012 0.015 0.018 0.02 0.022 0.027 0.033 0.039 0.047 0.050 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.20 0.22 0.27 0.33 0.39 0.47 0.50 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.0 2.2 2.7 3.0 3.3 3.9 4.7 5.0 632P103X9100 632P123X9100 632P153X9100 632P183X9100 632P203X9100 632P223X9100 632P273X9100 632P333X9100 632P393X9100 632P473X9100 632P503X9100 632P563X9100 632P683X9100 632P823X9100 632P104X9100 632P124X9100 632P154X9100 632P184X9100 632P204X9100 632P224X9100 632P274X9100 632P334X9100 632P394X9100 632P474X9100 632P504X9100 632P564X9100 632P684X9100 632P824X9100 632P105X9100 632P125X9100 632P155X9100 632P185X9100 632P205X9100 632P225X9100 632P275X9100 632P305X9100 632P335X9100 632P395X9100 632P475X9100 632P505X9100 0.001 0.0012 0.0015 0.0018 0.002 0.0022 0.0027 0.0033 0.0039 0.0047 0.005 0.0056 0.0068 0.0082 632P102X9200 632P122X9200 632P152X9200 632P182X9200 632P202X9200 632P222X9200 632P272X9200 632P332X9200 632P392X9200 632P472X9200 632P502X9200 632P562X9200 632P682X9200 632P822X9200 D 100 WVDC 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.190 [4.83] 0.190 [4.83] 0.190 [4.83] 0.190 [4.83] 0.190 [4.83] 0.170 [4.32] 0.190 [4.83] 0.190 [4.83] 0.190 [4.83] 0.230 [5.84] 0.230 [5.84] 0.230 [5.84] 0.230 [5.84] 0.310 [7.87] 0.230 [5.84] 0.230 [5.84] 0.250 [6.35] 0.310 [7.87] 0.310 [7.87] 0.310 [7.87] 0.370 [9.40] 0.370 [9.40] 0.370 [9.40] 0.400 [10.16] 0.370 [9.40] 0.400 [10.16] 0.400 [10.16] 0.450 [11.43] 0.450 [11.43] 0.450 [11.43] 0.500 [12.70] 0.500 [12.70] 0.500 [12.70] 0.450 [11.43] 0.500 [12.70] 0.600 [15.24] 0.600 [15.24] 200 WVDC 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] 0.170 [4.32] L LEAD AWG NO. 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.560 [14.22] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 1.000 [25.40] 1.000 [25.40] 1.000 [25.40] 1.000 [25.40] 1.000 [25.40] 1.000 [25.40] 1.000 [25.40] 1.250 [31.79] 1.250 [31.79] 1.500 [38.10] 1.500 [38.10] 1.310 [33.27] 1.310 [33.27] 24 24 24 24 24 24 24 24 24 24 24 24 22 22 22 22 22 22 22 22 22 22 22 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 0.440 [11.18] 24 24 24 24 24 24 24 24 24 24 24 24 24 24 * Part Numbers listed are for a capacitance tolerance of ± 10%. To specify ± 5% tolerance, change the "X9" in the Part Number to "X5"; for ± 2%, from "X9" to "X2". Document Number: 42028 Revision 04-Dec-03 For technical questions, contact [email protected] www.vishay.com 85 Type 632P Vishay Sprague STANDARD RATINGS in inches [millimeters] CASE SIZE LEAD L AWG NO. D 200 WVDC 0.01 632P103X9200 0.190 [4.83] 0.560 [14.22] 24 0.012 632P123X9200 0.190 [4.83] 0.560 [14.22] 24 0.015 632P153X9200 0.190 [4.83] 0.560 [14.22] 24 0.018 632P183X9200 0.190 [4.83] 0.560 [14.22] 24 0.02 632P203X9200 0.190 [4.83] 0.560 [14.22] 24 0.022 632P223X9200 0.190 [4.83] 0.560 [14.22] 24 0.027 632P273X9200 0.230 [5.84] 0.560 [14.22] 22 0.033 632P333X9200 0.230 [5.84] 0.560 [14.22] 22 0.039 632P393X9200 0.230 [5.84] 0.560 [14.22] 22 0.047 632P473X9200 0.230 [5.84] 0.560 [14.22] 22 0.05 632P503X9200 0.250 [6.35] 0.560 [14.22] 22 0.056 632P563X9200 0.270 [6.86] 0.560 [14.22] 22 0.068 632P683X9200 0.270 [6.86] 0.560 [14.22] 22 0.082 632P823X9200 0.310 [7.87] 0.560 [14.22] 22 0.10 632P104X9200 0.310 [7.87] 0.560 [14.22] 22 0.12 632P124X9200 0.270 [6.86] 0.750 [19.05] 22 0.15 632P154X9200 0.310 [7.87] 0.750 [19.05] 22 0.18 632P184X9200 0.310 [7.87] 0.750 [19.05] 22 0.20 632P204X9200 0.350 [8.89] 0.750 [19.05] 20 0.22 632P224X9200 0.350 [8.89] 0.750 [19.05] 20 0.27 632P274X9200 0.350 [8.89] 1.000 [25.40] 20 0.33 632P334X9200 0.370 [9.40] 1.000 [25.40] 20 0.39 632P394X9200 0.400 [10.16] 1.000 [25.40] 20 0.47 632P474X9200 0.400 [10.16] 1.000 [25.40] 20 0.50 632P504X9200 0.400 [10.16] 1.000 [25.40] 20 0.56 632P564X9200 0.450 [11.43] 1.000 [25.40] 20 0.68 632P684X9200 0.450 [11.43] 1.000 [25.40] 20 0.82 632P824X9200 0.500 [12.70] 1.000 [25.40] 20 1.0 632P105X9200 0.550 [13.97] 1.000 [25.40] 20 1.2 632P125X9200 0.500 [12.70] 1.250 [31.75] 20 1.5 632P155X9200 0.500 [12.70] 1.250 [31.75] 20 1.8 632P185X9200 0.500 [12.70] 1.810 [45.97] 20 2.0 632P205X9200 0.550 [13.97] 1.810 [45.97] 20 2.2 632P225X9200 0.550 [13.97] 1.810 [45.97] 20 2.7 632P275X9200 0.650 [16.51] 1.560 [39.62] 20 3.0 632P305X9200 0.700 [17.78] 1.560 [39.62] 20 3.3 632P335X9200 0.700 [17.78] 1.810 [45.97] 20 4.0 632P405X9200 0.750 [19.05] 1.810 [45.97] 20 4.7 632P475X9200 0.750 [19.05] 2.060 [52.32] 20 5.0 632P505X9200 0.750 [19.05] 20 2.060 [52.32] 400 WVDC 0.001 632P102X9400 24 0.190 [4.83] 0.440 [11.18] 0.0012 632P122X9400 0.440 [11.18] 24 0.190 [4.83] 0.0015 632P152X9400 0.190 [4.83] 0.440 [11.18] 24 0.0018 632P182X9400 0.190 [4.83] 0.440 [11.18] 24 0.002 632P202X9400 0.190 [4.83] 0.440 [11.18] 24 0.0022 632P222X9400 24 0.190 [4.83] 0.440 [11.18] 0.0033 632P332X9400 0.440 [11.18] 22 0.230 [5.84] 0.0039 632P392X9400 0.230 [5.84] 0.440 [11.18] 22 0.0047 632P472X9400 0.230 [5.84] 0.440 [11.18] 22 0.005 632P502X9400 22 0.230 [5.84] 0.440 [11.18] 0.0056 632P562X9400 22 0.230 [5.84] 0.440 [11.18] 0.0068 632P682X9400 0.560 [14.22] 22 0.230 [5.84] 0.0082 632P822X9400 0.230 [5.84] 0.560 [14.22] 22 0.01 632P103X9400 0.230 [5.84] 0.560 [14.22] 22 * Part Numbers listed are for a capacitance tolerance of ± 10%. To specify ± 5% tolerance, change the "X9" in the Part Number to "X5"; for ± 2%, from "X9" to "X2". CAPACITANCE (µF) www.vishay.com 86 PART NUMBER* For technical questions, contact [email protected] Document Number: 42028 Revision 04-Dec-03 Type 632P Vishay Sprague STANDARD RATINGS in inches [millimeters] CAPACITANCE (µF) CASE SIZE PART NUMBER* L LEAD AWG NO. 0.560 [14.22] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 0.750 [19.05] 1.000 [25.40] 1.000 [25.40] 1.000 [25.40] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.250 [31.75] 1.310 [33.27] 1.310 [33.27] 1.810 [45.97] 1.810 [45.97] 1.810 [45.97] 1.810 [45.97] 1.810 [45.97] 1.810 [45.97] 1.810 [45.97] 1.810 [45.97] 2.310 [58.70] 2.310 [58.70] 2.310 [58.70] 22 22 22 22 22 22 22 22 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 20 D 400 WVDC 0.012 0.015 0.018 0.02 0.022 0.027 0.033 0.039 0.047 0.050 0.056 0.068 0.082 0.10 0.12 0.15 0.18 0.20 0.22 0.27 0.33 0.39 0.47 0.50 0.56 0.68 0.82 1.0 1.2 1.5 1.8 2.0 632P123X9400 632P153X9400 632P183X9400 632P203X9400 632P223X9400 632P273X9400 632P333X9400 632P393X9400 632P473X9400 632P503X9400 632P563X9400 632P683X9400 632P823X9400 632P104X9400 632P124X9400 632P154X9400 632P184X9400 632P204X9400 632P224X9400 632P274X9400 632P334X9400 632P394X9400 632P474X9400 632P504X9400 632P564X9400 632P684X9400 632P824X9400 632P105X9400 632P125X9400 632P155X9400 632P185X9400 632P205X9400 0.250 [6.35] 0.230 [5.84] 0.270 [6.86] 0.310 [7.87] 0.310 [7.87] 0.310 [7.87] 0.310 [7.87] 0.310 [7.87] 0.400 [10.16] 0.400 [10.16] 0.400 [10.16] 0.400 [10.16] 0.370 [9.40] 0.400 [10.16] 0.400 [10.16] 0.400 [10.16] 0.450 [11.43] 0.500 [12.70] 0.500 [12.70] 0.550 [13.97] 0.550 [13.97] 0.500 [12.70] 0.550 [13.97] 0.550 [13.97] 0.600 [15.24] 0.650 [16.51] 0.700 [17.78] 0.750 [19.05] 0.900 [22.86] 0.900 [22.86] 0.950 [24.13] 1.000 [25.40] * Part numbers listed are for a capacitance tolerance of ± 10%. To specify ± 5% tolerance, change the "X9" in the Part Number to "X5"; for ± 2%, from "X9" to "X2." ORDERING INFORMATION 632P TYPE 103 CAPACITANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. Values must conform to the decade rating for the tolerance specified. X9 CAPACITANCE TOLERANCE 050 DC VOLTAGE RATING X9 = ± 10% X5 = ± 5% X2 = ± 2% This is expressed in volts. BECAUSE OF A WORLDWIDE SHORTAGE OF METALIZED POLYCARBONATE FILM, CERTAIN PART NUMBERS IN THE 632P SERIES MAY NOT BE AVAILABLE. PLEASE CHECK THE FACTORY FOR AVAILABILITY. Document Number: 42028 Revision 04-Dec-03 For technical questions, contact [email protected] www.vishay.com 87