MBRF1535CT THRU MBRF15100CT Isolation 15.0 AMPS. Schottky Barrier Rectifiers Voltage Range 35 to 100 Volts Current 15.0 Amperes ITO-220AB Features Plastic material used carries Underwriters Laboratory Classifications 94V-0 Metal silicon junction, majority carrier conduction Low power loss, high efficiency High current capability, low forward voltage drop High surge capability For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications Guardring for transient protection High temperature soldering guaranteed: o 260 C/10 seconds,0.25”(6.35mm)from case .112 (2 .85 ) .11 3 ( 3 .0 )D I A .10 0 ( 2 .5 5) . 2 72 ( 6 .9 ) . 2 48 ( 6 .3 ) . 6 06 (1 5. 5) . 5 83 (1 4. 8) Mechanical Data .1 34 (3 .4) D IA . 5 43 (1 3. 8) . 11 0 (2 .8 ) . 5 12 (1 3. 2) .09 8 ( 2 . 5 ) Cases: ITO-220AB molded plastic body Terminals: Leads solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting position: Any Mounting torque: 5 in. - lbs. max Weight: 0.08 ounce, 2.24 grams PIN 1 PIN 3 PIN 2 Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol MBRF MBRF MBRF MBRF MBRF MBRF Units Type Number 1535CT 1545CT 1550CT 1560CT 1590CT 15100CT Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage VRRM VRMS VDC 35 24 35 45 31 45 50 35 50 60 42 60 90 63 90 100 70 100 V V V Maximum Average Forward Rectified Current at TC=105oC Peak Repetitive Forward Current (Rated VR, Square Wave, 20KHz) at Tc=105oC Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) I(AV) 15 A IFRM 15.0 A Peak Repetitive Reverse Surge Current (Note 1) IRRM Maximum Instantaneous Forward Voltage at (Note 2) IF=7.5A, Tc=25OC IF=7.5A, Tc=125OC IF=15A, Tc=25OC O IF=15A, Tc=125 C Maximum Instantaneous Reverse Current @ Tc=25℃ at Rated DC Blocking Voltage (Note 2) @ Tc=125℃ Voltage Rate of Change (Rated VR) Maximum Thermal Resistance Per Leg (Note 3) Operating Junction Temperature Range Storage Temperature Range IFSM 150 1.0 0.57 0.84 0.72 0.1 15.0 dV/dt 0.75 0.65 1.0 50.0 10,000 RθJC TJ TSTG 3.5 -65 to +150 -65 to +175 VF IR Notes: 1. 2.0us Pulse Width, f=1.0 KHz 2. Pulse Test: 300us Pulse Width, 1% Duty Cycle 3. Thermal Resistance from Junction to Case with heatsink size of 2” x 3” x 0.25” AL-place - 150 - A 0.5 A 0.92 0.82 0.1 - V mA mA V/uS ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (MBRF1535CT THRU MBRF15100CT) FIG.1- FORWARD CURRENT DERATING CURVE FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PER LEG 300 RESISTIVE OR INDUCTIVE LOAD PEAK FORWARD SURGE CURRENT. (A) AVERAGE FORWARD CURRENT. (A) 25 20 15 10 5 200 150 100 50 0 0 50 100 Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method 250 0 150 1 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG.3- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG 50 Tj=125 0C 10 10 INSTANTANEOUS REVERSE CURRENT. (mA) INSTANTANEOUS FORWARD CURRENT. (A) 40 Pulse Width=300 s 1% Duty Cycle 1 Tj=25 0C 0.1 MBRF1535CT-MBRF1545CT MBRF1550CT-MBRF1560CT Tj=125 0C 1 0.1 Tj=75 0C MBRF1535CT-MBRF1545CT MBRF1550CT-MBRF15100CT 0.01 MBRF1590CT-MBRF15100CT 0.01 0 Tj=25 0C 0.001 0.1 0.2 0 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 FORWARD VOLTAGE. (V) FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG 100 TRANSIENT THERMAL IMPEDANCE. ( OC/W) Tj=25 0C f=1.0MHz Vsig=50mVp-p 1,000 JUNCTION CAPACITANCE.(pF) 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.6- TYPICAL TRANSIENT THERMAL CHARACTERISTICS PER LEG 4,000 100 40 MBRF1535CT-MBRF1560CT MBRF1590CT-MBRF15100CT 10 0.1 100 10 o CASE TEMPERATURE. ( C) 1.0 10 REVERSE VOLTAGE. (V) 100 10.0 1 0.1 0.01 0.1 1 T, PULSE DURATION. (sec) - 151 - 10 100