E M C C o m p o n e n t s February 2016 Common Mode Filters For automobile signal line ACT Series ACT45B Type ACT45B [1812 inch]* (CAN-BUS) * Dimensions Code JIS[EIA] (2/7) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20160216 / cmf_automotive_signal_act45b_en.fm (3/7) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Compatible with lead-free solders AEC-Q200 For automobile signal line Overview of ACT45B Type FEATURES Compatible with an operating temperature range of –40 to +150°C, so can be used for vehicle devices requiring compatibility with high temperatures. When mounting, the terminal and winding tape splicing part do not fuse. APPLICATION CAN-BUS, FAXs, modems, ISDNs, etc. PART NUMBER CONSTRUCTION ACT45B Series • Type name - 110 Inductance(typ.) (μH) 110 11 220 22 510 51 101 100 - 2P - Number of lines 2P 2 lines TL TL □□□ Packaging style Internal code ø330mm reel OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature （°C） （°C） ACT45B –40 to +150 –40 to +150 The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight (pieces/reel) 2,500 （g） 0.14 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20160216 / cmf_automotive_signal_act45b_en.fm (4/7) E M C C o m p o n e n t s ACT45B Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 60 to 120s Soldering Temp. Time T3 t2 230°C 40s max. Peak Temp. T4 245°C Time t3 5s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20160216 / cmf_automotive_signal_act45b_en.fm (5/7) E M C C o m p o n e n t s ACT45B Type SHAPE & DIMENSIONS 4.5±0.2 4 2 3 Marking 2.8±0.2 3.2±0.2 1 0.65±0.1 0.7±0.1 Dimensions in mm 1.6 CIRCUIT DIAGRAM 3.4 RECOMMENDED LAND PATTERN 1 4 2 3 • No polarity 3.2 5.9 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20160216 / cmf_automotive_signal_act45b_en.fm (6/7) E M C C o m p o n e n t s ACT45B Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance Common mode inductance Stray inductance [10MHz] (: )min. 300 500 1000 2000 [100kHz] (μH)+50/–30% 11 22 51 100 [100kHz] (μH)typ. 0.05 0.08 0.15 0.20 (: )typ. 600 1200 2800 5800 DC resistance Rated current Insulation resistance Rated voltage Part No. (: )max. 0.6 1.0 1.0 2.0 (M: )min. 10 10 10 10 (V)max. 50 50 50 50 ACT45B-110-2P-TL□□□ ACT45B-220-2P-TL□□□ ACT45B-510-2P-TL□□□ ACT45B-101-2P-TL□□□ ○ Measurement equipment Measurement item Product No. Common mode impedance 4991A Common mode inductance 4294A DC resistance 4338A Insulation resistance 4339A ＊ Equivalent measurement equipment may be used. (A)max. 0.25 0.2 0.2 0.15 Manufacturer Agilent Technologies Agilent Technologies Agilent Technologies Agilent Technologies IMPEDANCE VS. FREQUENCY CHARACTERISTICS 100000 510 Common mode 101 Common mode 10000 Impedance (Ω) 220 Common mode 1000 510 Differential mode 110 Common mode 101 Differential mode 100 220 Differential mode 110 Differential mode 10 1 10 100 1000 Frequency (MHz) ○ Measurement equipment Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20160216 / cmf_automotive_signal_act45b_en.fm (7/7) E M C C o m p o n e n t s ACT45B Type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 E A ø330±2 W1 13.5±0.5 W2 17.5±1 N 100±1 E 2 typ. N Type ACT45B 1.0 ø13.0±0.2 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS P0 t B W F P2 E øD0 A K P1 Dimensions in mm Type ACT45B Blank 160min. A 3.6±0.1 B 4.9±0.1 øD0 1.55±0.05 E 1.75±0.1 Products F 5.5±0.05 P0 4.0±0.1 P1 8.0±0.1 P2 2.0±0.05 W 12.0±0.2 K 3.05±0.1 t 0.3±0.05 Blank 400 to 500 Start End Drawing direction Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20160216 / cmf_automotive_signal_act45b_en.fm