Series AM1P-NZ 1 Watt | DC-DC Converter FEATURES: • • • • Models Single output Model AM1P-0505S-NZ AM1P-0509S-NZ AM1P-0512S-NZ AM1P-0515S-NZ AM1P-1205S-NZ AM1P-1209S-NZ AM1P-1212S-NZ AM1P-1215S-NZ AM1P-2405S-NZ AM1P-2409S-NZ AM1P-2412S-NZ AM1P-2415S-NZ Models Dual separated output Model AM1P-050505D-NZ Output Voltage (V) Output Current max (mA) Isolation (VDC) Efficiency (%) Input Voltage (V) Output Voltage (V) Output Current max (mA) Isolation (VDC) Efficiency (%) 4.5-5.5 4.5-5.5 4.5-5.5 4.5-5.5 10.8-13.2 10.8-13.2 10.8-13.2 10.8-13.2 21.6-26.4 21.6-26.4 21.6-26.4 21.6-26.4 Parameters Voltage range Filter Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance Output Specifications Voltage accuracy Short Circuit protection Line voltage regulation (Single) Line voltage regulation (Dual) Load voltage regulation (Single) Load voltage regulation (Dual) Temperature coefficient Ripple & Noise www.aimtec.com F 051e R11.E o • Operating temperature -40 C to + 85 C • Input / Output isolation 1000 VDC • Pin computable with multiple manufacturers • UL94-VO Package Input Voltage (V) Input Specifications Parameters o RoHS compliant 8 Pin DIP Package Low ripple and noise High efficiency up to 81% 5 9 12 15 5 9 12 15 5 9 12 15 4.5-5.5 200 110 83 67 200 110 83 67 200 110 83 67 5/5 Nominal 100 / 100 Typical 5 12 24 4.5-5.5 10.8-13.2 21.6-26.4 Conditions Typical 60 sec > 1000 60 Conditions Typical 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 1000 Maximum At 20 MHz Bandwidth Tel: +1 514 620 2722 1 of 3 72 Units VDC Capacitor Rated Units 1000 Maximum VDC MOhm pF See tolerance graph Momentary (1 sec) ±1.2 ±1.2 10 10 ±0.03 75 For 1.0% Vin For 1.0% Vin Load 10 – 100% Load 10 – 100% 78 79 80 78 78 80 81 79 79 80 81 79 Units % of Vin % of Vin % % o %/ C m Vp-p Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1P-NZ 1 Watt | DC-DC Converter General Specifications Parameters Conditions Switching frequency Operating temperature Storage temperature Case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Typical 100% load Without derating Maximum 150 -40 to +85 -55 to +125 Free air convection Plastic UL94-VO Units 90 KHz o C o C o C 90 % 1.8 g 0.46 x 0.39 x 0.30 inches 11.70 x 9.80 x 7.70 mm o >1 000 000 hrs (MIL-HDBK -217F, Ground Benign, t=+25 C) NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Safety Specifications Parameters Agency approvals Standards UL, CE for single output models IEC60950-1 :2001 Pin Out Specifications Pin 1 4 5 6 7 8 Single - V Input +V Input +V Output No pin -V Output No pin External capacitor Dual Separated Vin (VDC) -V Input +V Input +V1 Output -V1 Output +V2 Output -V2 Output 5 12 24 - External capacitor (uF) 4.7 2.2 1 - Vout (VDC) 5 9 12 15 External capacitor (uF) 10 4.7 2.2 1 Tolerance Envelope Graph +10% Typic al loa d line Output Voltage (%) +5% Nominal Voltage 10% 50% 100% Output Current (%) www.aimtec.com F 051e R11.E Tel: +1 514 620 2722 2 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM1P-NZ 1 Watt | DC-DC Converter Dimensions Filtering 11.70 (0.46) 7.62 (0.30) 0.50 (0.02) 1 7.62 (0.30) 9.80 (0.39) 4 Bottom View 8 7 6 5 2.54 (0.10) 7.70 (0.30) 4.10 (0.16) 0.50 (0.02) 2.54 (0.10) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R11.E Tel: +1 514 620 2722 3 of 3 Toll free: + 1 888 9 AIMTEC (924 6832) North America only