• 1 WATT UNREGULATED OUTPUT POWER • SINGLE-IN-LINE PACKAGE (SIP) • HIGH EFFICIENCY FOR LOW POWER APPLICATION • UL 94-V0 NON-CONDUCTED CASE • INTERNAL INPUT & OUTPUT FILTER • INPUT / OUTPUT ISOLATION UP TO 3KVDC The DU1P0 series are the standard building blocks for on-board distributed power systems. They are ideally suited to providing single and dual supplies on primarily digital boards with added benefit of galvanic isolation to reduce switching noise. All of the rated power may be drawn from a single pin provided the total load does not exceed 1 watt. T E C H N I C A L S P E C I F I C AT I O N All specifications are typical at nominal input, full load and 25ºC otherwise noted GENERAL SPECIFICATIONS OUTPUT SPECIFICATIONS Output power Voltage accuracy 1 Watt max Full load and nominal Vin ± 5% Minimum load (Note 1) 10% of FL Line regulation LL to HL at Full Load Load regulation 20% to 100% FL Ripple and noise 20MHz bandwidth 1.3% / 1% of Vin 5V output others Temperature coefficient Short circuit protection ± 10% ± 8% 100mVp-p Input filter Isolation voltage See table Input to Output Standard Suffix-N 9 Isolation resistance 10 ohms, min Isolation capacitance 30pF, max Switching frequency 60KHz, min Design meet safety standard UL1950, EN60950 Case material Non-conductive black plastic Short term Base material None Potting material 5V nominal input 12V nominal input 15V nominal input 24V nominal input 1000VDC, min 3000VDC, min I0.1% / ºC, max INPUT SPECIFICATIONS Input voltage range Efficiency 4.5 – 5.5VDC 10.8 – 13.2VDC 13.5 – 16.5VDC 21.6 – 26.4VDC Capacitor Epoxy (UL94-V0) 0.77 X 0.24 X 0.40 Inch (19.6 X 6.0 X 10.2 mm) Dimensions Weight 2.0g (0.071oz) MTBF (Note 2) 1.471 x 107 hrs ENVIRONMENTAL SPECIFICATIONS Operating temperature range -25ºC ~ +85ºC (with derating) Storage temperature range -55ºC ~ +105ºC Thermal shock MIL-STD-810D Vibration Relative humidity 10~55Hz, 2G, 30minutes along X,Y and Z 5% to 95% RH (4) Model Number Input Range Output Voltage Output Current Input (3) Current Eff (%) Capacitor (5) Load max DU1P0-05S05 DU1P0-05S12 DU1P0-05S15 DU1P0-05D05 DU1P0-05D12 DU1P0-05D15 DU1P0-12S05 DU1P0-12S12 DU1P0-12S15 DU1P0-12D05 DU1P0-12D12 DU1P0-12D15 DU1P0-15S05 DU1P0-15S12 DU1P0-15S15 DU1P0-15D05 DU1P0-15D12 DU1P0-15D15 DU1P0-24S05 DU1P0-24S12 DU1P0-24S15 DU1P0-24D05 DU1P0-24D12 DU1P0-24D15 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 4.5 – 5.5 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 10.8 – 13.2 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 13.5 – 16.5 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 21.6 – 26.4 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 5 VDC 12 VDC 15 VDC ± 5 VDC ± 12 VDC ± 15 VDC 200mA 83mA 67mA ± 100mA ± 42mA ± 33mA 200mA 83mA 67mA ± 100mA ± 42mA ± 33mA 200mA 83mA 67mA ± 100mA ± 42mA ± 33mA 200mA 83mA 67mA ± 100mA ± 42mA ± 33mA 298mA 269mA 272mA 295mA 273mA 268mA 121mA 111mA 112mA 119mA 111mA 109mA 97mA 89mA 89mA 95mA 88mA 87mA 62mA 58mA 57mA 61mA 57mA 55mA 71 78 78 72 78 78 73 79 79 74 80 80 73 79 79 74 80 80 71 76 78 72 78 79 6.2uF 6.2uF 6.2uF 3.0uF 3.0uF 3.0uF 6.2uF 6.2uF 6.2uF 3.0uF 3.0uF 3.0uF 6.2uF 6.2uF 6.2uF 3.0uF 3.0uF 3.0uF 6.2uF 6.2uF 6.2uF 3.0uF 3.0uF 3.0uF 0.77(19.6) Note 1. The DU1P0 series required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40ºC. (Ground fixed and controlled environment). Maximum value at nominal input voltage and full load of standard type. Typical value at nominal input voltage and full load. Test by minimum Vin and constant resistor load. 2. 3. 4. 5. 0.016(0.4) FRONT VIEW 0.40(10.2) 0.01x 0.02 ( 0.25 x 0.5) Rectangular Pin 0.10(2.54) 0.14(3.6) 0.085(2.16) 0.20(5.08) 0.24(6.1) 1 BOTTOM VIEW 2 4 5 6 7 0.053(1.35) OUTPUT POWER (%) 1. All dimensions in Inches (mm) 2. Pin pitch tolerance I0.014(0.35) DU1P0-24S05 Derating Curve STANDARD “N” Models 100 PIN SINGLE DUAL PIN SINGLE DUAL 75 1 2 4 5 6 + INPUT - INPUT - OUTPUT NC + OUTPUT + INPUT - INPUT 1 2 + INPUT - INPUT + INPUT - INPUT 50 Nature convection 25 0 -40 -25 -10 0 50 60 70 80 90 100 AMBIENT TEMPERATURE (ºC) - OUTPUT COMMON + OUTPUT 5 6 7 - OUTPUT - OUTPUT NC COMMON + OUTPUT + OUTPUT