NS5S1153 USB 2.0 High Speed and Audio Switch with Negative Swing Capability The NS5S1153 is a DPDT switch for combined true−ground audio and USB 2.0 high speed data applications. It allows portable systems to use a single port to pass either USB data or audio signals from an external headset; headset; the 2 channels being compliant to USB 2.0, USB 1.1 and USB 1.0. The switch is capable of passing signals with negative voltages as low as 2 V below ground. The device features shunt resistors on the audio ports. These resistors are switched in when the audio channel is off and provide a safe path to ground for any charge that may build up on the audio lines. This reduces Pop & Click noise in the audio system. The NS5S1153 is also equipped with VBUS detection circuitry to immediately switch to USB mode in the event that a voltage is detected on VBUS. The NS5S1153 is housed in a space saving, ultra low profile 1.4 x 1.8 x 0.5 mm 10 pin UQFN package. www.onsemi.com MARKING DIAGRAMS UQFN10 CASE 488AT 1 AJ M G AJM G G = Specific Device Code = Date Code = Pb−Free Package (Note: Microdot may be in either location) Features • • • • • • • • • 2:1 High Speed Switch USB 2.0, USB 1.1 & USB 1.0 Capable on all channels High Bandwidth of 820 MHz on D+/D− Capable of Passing Negative Swing Signals Down to −2 V on R/L Channel 1.8 V Compatible Control Pin & VBUS Detection Circuitry for Automatic Switching Audio Channel Shunt Resistors for Pop & Click Noise Reduction Ultra−Low THD in Audio Mode: 0.01% into 16 Load 5.25 V Tolerant Common Pins This is a Pb−Free Device ORDERING INFORMATION Device NS5S1153MUTAG Package Shipping† UQFN10 3000 / Tape & Reel (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Typical Applications • • • • • • Micro or Mini USB Applications Shared High Speed Data or Audio on a Single Connector Mobile Phones Tablets Bar Code Scanners Portable Devices NS5S1153 VBUS_CTRL D+ USB/ UART COM+ USB Connector D− COM− R GND L USB/ UART/ Audio Figure 1. Application Diagram © Semiconductor Components Industries, LLC, 2011 August, 2016 − Rev. 3 1 Publication Order Number: NS5S1153/D NS5S1153 COM+ COM- 7 ASel 6 8 5 VCC 4 GND 3 L Control Logic 9 VBUS_CTRL VBUS Detect VBUS_PD 10 D+ 1 2 D- R Figure 2. Functional Block Diagram (Top View) PIN DESCRIPTIONS Pin # Name Direction Description 1 D− I/O Negative Data Line for USB Signals 2 R I/O Right Line for Audio Signals 3 L I/O Left Line for Audio Signals 4 GND Power Ground 5 VCC Power Power Supply 6 COM− I/O Left Audio / Negative Data Common Line 7 COM+ I/O Right Audio / Positive Data Common Line 8 ASEL Input 9 VBUS_CTRL Input 10 D+ I/O Control Input Override Select Line Control Input Select Line from VBUS. If this pin is driven by an open drain I/O, we suggest maximum 100 k pull up. Positive Data Line for USB Signals TRUTH TABLE ASEL VBUS L, R D+, D− L, R SHUNT Low Low ON OFF OFF Low High OFF ON ON High X ON OFF OFF www.onsemi.com 2 NS5S1153 OPERATING CONDITIONS MAXIMUM RATINGS Symbol Pins Parameter Value Unit VCC VCC Positive DC Supply Voltage −0.5 to +6.0 V VBUS VBUS_CTRL VBUS Control Input Voltage −0.5 to +6.0 V Analog Signal Voltage −0.5 to +6.0 V VIS D+ to COM+ D− to COM− R to COM+ L to COM− −2.5 to VCC + 0.5 VIS COM+, COM− VIN ASel Control Input Override Voltage ICC VCC Positive DC Supply Current TS DC Signal Voltage Tolerance (<24 hours) V 5.25 Storage Temperature −0.5 to +6.0 V 50 mA −65 to +150 °C IIS_CON COM+, COM− R, L, D+, D− Analog Signal Continuous Current−Closed Switch $100 mA IIS_PK COM+, COM− R, L, D+, D− Analog Signal Continuous Current 10% Duty Cycle $500 mA Control Input Override Current 1 mA VBUS Control Input Current 1 IIN ASel VBUS_CTRL Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. RECOMMENDED OPERATING CONDITIONS Symbol Pins VCC VCC VBUS VBUS_CTRL VIS D+ to COM+ D− to COM− Parameter Min Max Unit Positive DC Supply Voltage 2.7 5.0 V VBUS Control Input Voltage GND 5.25 V Analog Signal Voltage (Note 1) GND VCC V −2.0 VCC GND VCC V −40 +85 °C R to COM+ L to COM− VIN TA ASel Control Input Override Voltage Operating Temperature Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 1. In USB mode, any signal applied to the off−state audio inputs R, L may not swing below ground or above 1.5 V. www.onsemi.com 3 NS5S1153 DC ELECTRICAL CHARACTERISTICS CONTROL INPUT (Typical: T = 25°C, VCC = 3.3 V) −40°C to +85°C Symbol VIH Pins ASEL Parameter Control Input HIGH Voltage VIL ASEL Control Input LOW Voltage IIN VIH ASEL VBUS_CTRL Current Input Leakage Current VBUS Control Input HIGH Voltage VIL VBUS_CTRL VBUS Control Input LOW Voltage IIN VBUS_CTRL VBUS Current Input Leakage Current Test Conditions 0 ≤ VIS ≤ VCC 0 ≤ VIS ≤ VCC VCC (V) 2.7 3.3 4.2 Min Typ Max 1.3 1.4 1.5 − − 2.7 3.3 4.2 − − 0.4 0.4 0.4 V 4.2 2.7 3.3 4.2 − 1.9 2.2 2.7 − − ±50 − nA V 2.7 3.3 4.2 − − 0.8 1.1 1.6 V 4.2 − − ±25 A Unit V SUPPLY CURRENT AND LEAKAGE (Typical: T = 25°C, VCC = 3.3 V) −40°C to +85°C Symbol INC,NO(OFF) Pins D+, D− Parameter OFF State Leakage Test Conditions VBUS_CTRL = 0 V, 4.2 V; VCOM−, VCOM+ = 0 V, 4.2 V VD+, VD− = 4.2 V, 0 V or float VL, VR = float or 4.2 V, 0 V VCC (V) 4.2 ICOM(ON) COM−, COM+ ON State Leakage 4.2 ICC IOFF VCC COM−, COM+ Quiescent Supply Power OFF Leakage VBUS_CTRL = 0 V, 4.2 V; VCOM−, VCOM+ = 0 V, 4.2 V VD+, VD− = 4.2 V, 0 V or float VL, VR = float or 4.2 V, 0 V VIS = GND to VCC; ID = 0 A 0 ≤ VIS ≤ 4.2 V Min 4.2 0 Typ 21 Max ±80 Unit nA ±100 nA 35 50 A A USB ON RESISTANCE (Typical: T = 25°C, VCC = 3.3 V) −40°C to +85°C VCC (V) 2.7 3.3 4.2 Min Typ Max 3.0 3.0 3.0 5.5 4.6 4.6 Symbol RON Pins D+ to COM+ D− to COM− Parameter On−Resistance Test Conditions ION = 10 mA VIS = 0 V to VCC Unit RFLAT D+ to COM+ D− to COM− On−Resistance Flatness ION = 10 mA VIS = 0 V to VCC 2.7 3.3 4.2 0.08 0.08 0.08 RON D+ to COM+ D− to COM− On−Resistance Matching ION = 10 mA VIS = 0 V to VCC 2.7 3.3 4.2 0.03 0.03 0.03 AUDIO ON RESISTANCE (Typical: T = 25°C, VCC = 3.3 V) −40°C to +85°C Typ Max 3.0 3.0 3.0 4.6 4.6 4.6 Pins R to COM+ L to COM− Parameter On−Resistance Test Conditions ION = 10 mA VIS = −1.5 to 1.5 RFLAT R to COM+ L to COM− On−Resistance Flatness ION = 10 mA VIS = −1.5 to 1.5 2.7 3.3 4.2 0.11 0.11 0.11 RON R to COM+ L to COM− On−Resistance Matching ION = 10 mA VIS = −0.85 to 0.85 2.7 3.3 4.2 0.03 0.03 0.03 Shunt Resistance (Resistor + Switch) ION = 10 mA 2.7 118 VBUS_CTRL Pull−down Resistor ION = 10 mA RSH VBUS_PD L, R VBUS_CTRL www.onsemi.com 4 VCC (V) 2.7 3.3 4.2 Min Symbol RON 530 160 Unit k NS5S1153 AC ELECTRICAL CHARACTERISTICS TIMING/FREQUENCY (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 35 pF, f = 1 MHz) −405C to +855C Symbol Pins Parameter Test Conditions VCC (V) Min Typ Max Unit tON Turn−ON Time (Closed to Open) (Figures 8 and 9) 2.7 − 4.2 − 14 − s tOFF Turn−OFF Time (Closed to Open) (Figures 8 and 9) 2.7 − 4.2 − 75 − ns TBBM Break−Before−Make Time (Figure 7) − 7.0 − s − 900 − MHz BW D+ to COM+ −3 dB Bandwidth (Figure 10) D− to COM− CL = 5 pF RS = 50 ISOLATION (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 5 pF) −405C to +855C Symbol Pins OIRR Open XTALK COM+ to COM− THD+N THD PSRR Min Typ Max Unit OFF−Isolation (Figure 10) f = 100 kHz, RS = 50 − −81 − dB Non−Adjacent Channel Crosstalk (Figure 10) f = 100 kHz, RS = 50 − −93 − dB Total Harmonic Distortion + Noise VBUS_CTRL = 0 V ASEL = 3.0 V f = 20 Hz to 20 kHz VCOM = 0.5 Vpp RL = 600 3.0 − 0.001 − % Total Harmonic Distortion VBUS_CTRL = 0 V ASEL = 0 V, 3.6 V f = 1 kHz VCOM = ±2.0 Vpp RL = 16 3.6 − 0.01 − % Power Supply Rejection Ratio f = 10 kHz RCOM = 50 3.0 − 60 − dB Parameter Test Conditions VCC (V) CAPACITANCE (Typical: T = 25°C, VCC = 3.3 V, RL = 50 , CL = 5 pF, f = 1 MHz, ASEL = 0 V) −405C to +855C Symbol Pins CIN ASEL CON Parameter Test Conditions Min Typ Max Unit Control Pin Input Capacitance VCC = 0 V − 2.6 − pF D+ to COM+ D− to COM− USB ON Capacitance VBUS_CTRL = 5 V − 6.9 − pF CON R to COM+ L to COM− Audio ON Capacitance VBUS_CTRL = 0 V − 9.3 − pF COFF D+, D− USB OFF Capacitance VBUS_CTRL = 0 V − 4.8 − pF COFF R, L Audio OFF Capacitance VBUS_CTRL = 5 V − 4.8 − pF www.onsemi.com 5 NS5S1153 Figure 3. High Speed USB Eye Diagram of Signal Path without Switch Figure 4. High Speed USB Eye Diagram of Signal Path with NS5S1153 (VCC = 3.6 V) 4 4 Vcc=2.7V Vcc=3.3V 3.6 3.6 3.4 3.4 3.2 3 2.8 2.8 2.6 2.4 2.2 2.2 1 1.5 2 2.5 3 3.5 Vcc=3.3V 3 2.4 −2 −1.5 −1 −0.5 0 0.5 Vcc=2.7V 3.2 2.6 2 Vcc=4.2V 3.8 RON (Ohms) RON (Ohms) 3.8 Vcc=4.2V 2 4 0 0.5 1 1.5 2 2.5 3 3.5 VIS (V) VIS (V) Figure 5. Audio ON Resistance vs. Signal Voltage @ T = 255C, 2.7 V 3 VCC 3 4.2 V Figure 6. USB ON Resistance vs. Signal Voltage @ T = 255C, 2.7 V 3 VCC 3 4.2 V www.onsemi.com 6 4 NS5S1153 VCC DUT VCC Input Output GND VOUT 0.1 F 50 35 pF tBMM Output 50 % OF DROOP VOLTAGE DROOP Switch Select Pin Figure 7. tBBM (Time Break−Before−Make) VCC Input DUT VCC 0.1 F 50% Output VOUT Open 50% 0V 50 VOH 90% 35 pF 90% Output VOL Input tON Figure 8. tON/tOFF VCC VCC Input DUT Output 50 50% 50% 0V VOUT Open tOFF VOH 35 pF Output Input tOFF Figure 9. tON/tOFF www.onsemi.com 7 10% 10% VOL tON NS5S1153 50 Reference DUT Transmitted Input Output 50 Generator 50 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is the bandwidth of an On switch. VISO, Bandwidth and VONL are independent of the input signal direction. ǒVVOUT Ǔ for VIN at 100 kHz IN VOUT Ǔ for VIN at 100 kHz to 50 MHz VONL = On Channel Loss = 20 Log ǒ VIN VISO = Off Channel Isolation = 20 Log Bandwidth (BW) = the frequency 3 dB below VONL VCT = Use VISO setup and test to all other switch analog input/outputs terminated with 50 Figure 10. Off Channel Isolation/On Channel Loss (BW)/Crosstalk (On Channel to Off Channel)/VONL www.onsemi.com 8 NS5S1153 PACKAGE DIMENSIONS UQFN10 1.4x1.8, 0.4P CASE 488AT ISSUE A EDGE OF PACKAGE ÉÉ ÉÉ ÉÉ D PIN 1 REFERENCE 2X 2X 0.10 C L1 E DETAIL A Bottom View (Optional) 0.10 C B TOP VIEW A1 0.05 C A1 C SIDE VIEW 3 9X EXPOSED Cu A 0.05 C 10X 5 SEATING PLANE ÉÉ ÉÉ A3 DETAIL B Side View (Optional) 1.700 0.0669 6 0.663 0.0261 e 10 X L3 b MILLIMETERS MIN MAX 0.45 0.60 0.00 0.05 0.127 REF 0.15 0.25 1.40 BSC 1.80 BSC 0.40 BSC 0.30 0.50 0.00 0.15 0.40 0.60 MOUNTING FOOTPRINT e/2 1 DIM A A1 A3 b D E e L L1 L3 MOLD CMPD L 10 NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 0.25 AND 0.30 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. A 0.200 0.0079 0.10 C A B 0.05 C 9X 0.563 0.0221 1 2.100 0.0827 NOTE 3 BOTTOM VIEW 0.400 0.0157 PITCH 10 X 0.225 0.0089 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] ◊ N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5817−1050 www.onsemi.com 9 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NS5S1153/D