ams ASJM High-speed, low-voltage, single-supply, 0.8-ohm, dual spst analog switch Datasheet

a u s t ri a m i c r o s y s t e m s
AS1741, AS1742, AS1743
D a ta S he e t
H i g h - Sp e e d , L o w - Vo l ta g e , S i n g l e - S u p p l y, 0 . 8Ω,
Dual SPST Analog Switches
1 General Description
2 Key Features
The AS1741/AS1742/AS1743 are high-speed, low-voltage, dual single-pole/single-throw (SPST) analog
switches.
Fast switching speeds, low ON-resistance, and low
power-consumption make these devices ideal for singlecell battery powered applications.
These highly-reliable devices operate from a single +1.6
to +3.6V supply, and are differentiated by the type and
number of switches as listed in Table 1.
Table 1. Standard Products
Model
Switch Types
AS1741
Two Normally Open (NO) Switches
AS1742
Two Normally Closed (NC) Switches
AS1743
One NO Switch and One NC Switch
The AS1743 supports break-before-make switching.
With very low ON-resistance (RON), RON matching, and
RON flatness, the devices can accurately switch signals
for sample and hold circuits, digital filters, and op-amp
gain switching networks.
The AS1741/AS1742/AS1743 digital logic input is 1.8V
CMOS-compatible when using a single +3V supply, and
all devices can handle Rail-to-Rail signals.
!
ON-Resistance:
- 0.8Ω (+3V supply)
- 2.5Ω (+1.8V supply)
!
RON Matching: 0.08Ω (+3V supply)
!
RON Flatness: 0.18Ω (+3V supply)
!
Supply Voltage Range: +1.6 to +3.6V
!
Switching Action: tON = 22ns, tOFF = 14ns
!
Current-Handling: 250mA Continuous
!
Break-Before-Make Switching (AS1743)
!
Rail-to-Rail Signal Handling
!
1.8V CMOS Logic Compatible (+3V supply)
!
Total Harmonic Distortion: 0.03%
!
Operating Temperature Range: -40 to +85ºC
!
Package Types:
- 8-pin MSOP
- 8-pin SOT23
The devices are available in an 8-pin MSOP package
and an 8-pin SOT23 package.
3 Applications
The devices are ideal for use in power routing systems,
cordless and mobile phones, MP3 players, CD and DVD
players, PDAs, handheld computers, digital cameras,
hard drives, and any other application where high-speed
signal switching is required.
Figure 1. MSOP Block Diagrams
AS1741
NO1
COM1
IN2
GND
AS1742
V+
IN1
COM2
NO2
www.austriamicrosystems.com
NC1
AS1743
V+
COM1
IN1
IN2
COM2
GND
NC2
Revision 1.76
NO1
COM1
IN2
GND
V+
IN1
COM2
NC2
1 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
4 Absolute Maximum Ratings
Stresses beyond those listed in Table 2 may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated in Section 5 Electrical
Characteristics on page 3 is not implied. Exposure to absolute maximum rating conditions for extended periods may
affect device reliability.
Table 2. Absolute Maximum Ratings
Parameter
Min
Max
Units
V+, INx to GND
-0.3
+5
V
-0.3
V+
+ 0.3
V
COMx, NOx, NCx Continuous Current
-250
+250
mA
COMx, NOx, NCx Peak Current
-350
+350
mA
Continuous Power Dissipation (TAMB = +70ºC)
362
mW
Derate at 4.5mW/ºC above +70ºC
Electro-Static Discharge
2500
V
HBM Mil-Std883E 3015.7 methods
Latch Up Immunity IN1, IN2
150
mA
Latch Up Immunity all other Pins
250
mA
COMx, NOx, NCx to GND
†
Operating Temperature Range
-40
Junction Temperature
Storage Temperature Range
Package Body Temperature
-65
+85
ºC
+150
ºC
+150
ºC
+260
ºC
Comments
Pulsed at 1ms 10% duty cycle
Norm: JEDEC 17
The reflow peak soldering temperature (body
temperature) specified is in accordance with
IPC/JEDEC J-STD-020C “Moisture/Reflow
Sensitivity Classification for Non-Hermetic
Solid State Surface Mount Devices”
†
Signals on pins COM1, COM2, NO1, NO2, NC1, or NC2 that exceed V+ or GND are clamped by internal diodes.
Limit forward-diode current to the maximum current rating.
www.austriamicrosystems.com
Revision 1.76
2 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
5 Electrical Characteristics
Table 3. Power Supply Characteristics
Symbol
Parameter
Conditions
V+
Power Supply Range
I+
Positive Supply
Current
Min
Typ
1.6
V+ = 3.6V, VINx = 0 or V+, all channels on or off
0.01
Max Unit
3.6
V
1
µA
V+ = +2.7 to +3.6V, VIH = +1.4V, VIL = +0.5V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ V+ =
+3.0V, TAMB = +25ºC.
Table 4. +3V Supply Electrical Characteristics
Symbol
Parameter
Analog Switch
VCOMx,
VNOx, VNCx Analog Signal Range
Min
ON-Resistance
∆RON
ON-Resistance Match
1
Between Channels
ON-Resistance
2
Flatness
INOx(OFF),
INCx(OFF)
NOx or NCx OffLeakage Current
ICOMx(OFF)
COMx Off-Leakage
Current
ICOMx(ON)
COMx On-Leakage
Current
Typ
0
TAMB = +25ºC
TAMB = TMIN to TMAX
TAMB = +25ºC
V+ = 2.7V, ICOMx = 100mA,
VNOx or VNCx = 1.5V
TAMB = TMIN to TMAX
TAMB = +25ºC
V+ = 2.7V, ICOMx = 100mA,
VNOx or VNCx = 1, 1.5, or 2V TAMB = TMIN to TMAX
V+ = 3.3V,
TAMB = +25ºC
VCOMx = 0.3 or 3.0V, VNOx or
TAMB = TMIN to TMAX
VNCx = 3.0 or 0.3V
V+ = 3.3V,
VCOMx = 0.3 or 3.0V,
VNOx or VNCx = 3.0, 0.3V
V+ = 3.3V,
VCOMx = 3.0 or 0.3V,
NOx or VNCx = 3.0 or 0.3V
Max Unit
V+
V
Ω
-1
0.8
0.9
0.08
0.09
0.18
0.20
1
-5
5
0.35
V+ = 2.7V, ICOMx = 100mA,
VNOx or VNCx = 1.5V
RON
RFLAT(ON)
Conditions
0.02
0.02
TAMB = +25ºC
-1
1
TAMB = TMIN to TMAX
-5
5
TAMB = +25ºC
-2
2
TAMB = TMIN to TMAX
-10
10
Ω
Ω
nA
nA
nA
Switch Dynamic Characteristics
3
tON
Turn On Time
tOFF
Turn Off Time
tBBM
Break Before Make
3
3
Q
Charge Injection
COFF
NOx, NCx OffCapacitance
COMx Off-Capacitance
COMx On-Capacitance
-3dB On-Channel
Bandwidth
CCOMx(OFF)
CCOMx(ON)
BW
VISO
Off-Isolation
Crosstalk
THD
4
5
Total Harmonic
Distortion
www.austriamicrosystems.com
VNOx or VNCx = 1.5V,
TAMB = +25ºC
RLOAD = 50Ω, CLOAD = 35pF,
TAMB = TMIN to TMAX
Figures 12, 13
VNOx or VNCx = 1.5V,
TAMB = +25ºC
RLOAD = 50Ω, CLOAD = 35pF,
TAMB = TMIN to TMAX
Figures 12, 13
VNOx or VNCx = 1.5V,
TAMB = +25ºC
RLOAD = 50Ω, CLOAD = 35p,
T
AMB
= TMIN to TMAX
Figure 14 (AS1743)
8-pin MSOP
VGEN = 3.3V, RGEN = 0,
CLOAD = 1.0nF, Figure 15
8-pin SOT23
13
22
24
7
ns
14
15
ns
6
ns
1
6
5
pC
f = 1MHz, Figure 16
35
pF
f = 1MHz, Figure 16
f = 1MHz, Figure 16
Signal = 0, RIN = ROUT = 50Ω,
CLOAD = 5pF, Figure 17
f = 1MHz, VCOMx = 1VRMS,
RLOAD = 50Ω, CLOAD = 5pF, Figure 17
f = 1MHz, VCOMx = 1VRMS,
RLOAD = 50Ω, CLOAD = 5pF, Figure 17
f = 20Hz to 20kHz,
VCOMx = 2Vp-p, RLOAD = 32Ω
35
35
pF
pF
130
MHz
-55
dB
-100
dB
0.03
%
Revision 1.76
3 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Table 4. +3V Supply Electrical Characteristics (Continued)
Symbol
Parameter
Logic Input
VIH
Input Logic High
VIL
Input Logic Low
IIN
Input Leakage Current
Conditions
Min
Typ
Max Unit
0.1
0.5
1000
1.4
VINx = 0 or V+
-1000
V
V
nA
V+ = +1.8V, VIH = +1.0V, VIL = 0.4V, TAMB = TMIN to TMAX (unless otherwise specified). Typ values @ TAMB = +25ºC.
Table 5. +1.8V Supply Electrical Characteristics
Symbol
Parameter
Analog Switch
VCOMx,
VNOx, VNCx Analog Signal Range
Conditions
Min
0
TAMB = +25ºC
TAMB = TMIN to TMAX
TAMB = +25ºC
VCOMx = 0.3 or 1.5V, VNOx
or VNCx = 1.5 or 0.3V
TAMB = TMIN to TMAX
TAMB = +25ºC
VCOMx = 0.3 or 1.5V, VNOx
or VNCx = 1.5 or 0.3V
TAMB = TMIN to TMAX
TAMB = +25ºC
VCOMx = 0.3 or 1.5V,
VNOx or VNCx = 0.3 or 1.5V TAMB = TMIN to TMAX
0.9
ICOMx = 10mA,
VNOx or VNCx = 0.9V
RON
ON-Resistance
INOx(OFF),
INCx(OFF)
NOx or NCx OffLeakage Current
ICOMx(OFF)
COMx Off-Leakage
Current
ICOMx(ON)
COMx On-Leakage
Current
Typ
-1
-5
-1
-5
-2
-10
Max
Unit
V+
V
2.5
3
1
5
1
5
2
10
Ω
nA
nA
nA
Switch Dynamic Characteristics
tON
Turn On Time
3
3
tOFF
Turn Off Time
tBBM
Break-Before-Make
Q
VISO
3
Charge Injection
Off-Isolation
Crosstalk
4
5
Logic Input
VIH
Input Logic High
VIL
Input Logic Low
IIN
Input Leakage Current
VNOx or VNCx = 1.5V,
RLOAD = 50Ω,
CLOAD = 35pF,
Figures 12, 13
VNOx or VNCx = 1.5V,
RLOAD = 50Ω,
CLOAD = 35pF,
Figures 12, 13
VNOx or VNCx = 1.5V,
RLOAD = 50Ω,
CLOAD = 35p,
Figure 14, (AS1743)
TAMB = +25ºC
21
TAMB = TMIN to TMAX
35
TAMB = +25ºC
12
TAMB = TMIN to TMAX
ns
8
ns
1
8-pin MSOP
8-pin SOT23
f = 1MHz, VCOMx = 1VRMS,
RLOAD = 50Ω, CLOAD = 5pF, Figure 17
f = 1MHz, VCOMx = 1VRMS,
RLOAD = 50Ω, CLOAD = 5pF, Figure 17
VGEN = 1.8V, RGEN = 0,
CLOAD = 1.0nF, Figure 15
6
2.5
pC
-50
dB
-100
dB
1
VINx = 0 or V+
ns
20
25
TAMB = +25ºC
TAMB = TMIN to TMAX
30
-1000
0.1
0.4
1000
V
V
nA
1. ∆RON = RON(MAX) - RON(MIN).
2. Flatness is defined as the difference between the maximum and the minimum value of ON-resistance as measured
over the specified analog signal ranges.
3. Guaranteed by design.
4. Off-Isolation = 20log10(VCOMx/VNOx), VCOMx = output, VNOx = input to off switch.
5. Between two switches.
www.austriamicrosystems.com
Revision 1.76
4 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
6 Typical Operating Characteristics
Figure 3. Charge Injection vs. Output Voltage; MSOP
45
45
40
40
35
35
30
30
Q (pC)
Q (pC)
Figure 2. Charge Injection vs. Output Voltage; SOT23
25
VDD = 3V
20
25
20
VDD = 1.8V
15
15
10
10
VDD = 1.8V
5
5
0
0
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3
VBIAS (V)
VBIAS (V)
Figure 4. RON vs. VCOM and Temperature; VDD = 2.7V
Figure 5. RON vs. VCOM
1.0
0.50
VDD = 1.8V
0.9
Temp = +85ºC
0.45
0.8
RON (Ω )
0.40
RON (Ω )
VDD = 3V
Temp = +25ºC
0.35
0.30
0.7
VDD = 2V
VDD = 2.7V
VDD = 3V
0.6
VDD = 2.5V
0.5
Temp = -40ºC
0.25
VDD = 3.3V
0.4
0.20
VDD = 3.6V
0.3
0
0.5
1
1.5
2
2.5
3
0
0.5
Figure 6. tON/tOFF vs. Supply Voltage
1
1.5
2
2.5
3
3.5
VCOM (V)
VCOM (V)
Figure 7. tON/tOFF vs. Temperature
25
24
22
18
16
tON
14
12
10
8
tOFF
tON/tOFF (ns)
tON/tOFF (ns)
tON/VDD = 3V
20
20
tOFF/VDD = 3V
15
tON/VDD = 1.8V
10
5
6
tOFF/VDD = 1.8V
4
1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6
0
-40
VDD (V)
www.austriamicrosystems.com
-15
10
35
60
85
Temperature (°C)
Revision 1.76
5 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Figure 8. THD vs. Frequency; RLOAD = 32Ω, VDD = 3V
Figure 9. Frequency Response
20
0.06
0
0.05
Bandwidth
-20
Loss (dB)
THD (%)
0.04
0.03
0.02
-40
-60
-80
0.01
-100
0.00
1
10
100
-120
0.001
Frequency (kHz)
www.austriamicrosystems.com
0.1
10
1000
Frequency (MHz)
Revision 1.76
6 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Pin Assignments
7 Pinout
Pin Assignments
Figure 10. MSOP Pin Assignments (Top View)
NO1 1
8 V+
COM1 2
7 IN1
NC1 1
COM1 2
6 COM2
GND 4
NO1 1
7 IN1
5 NO2
IN2 3
7 IN1
AS1743
6 COM2
GND 4
8 V+
COM1 2
AS1742
AS1741
IN2 3
8 V+
IN2 3
6 COM2
5 NC2
GND 4
5 NC2
8 NC1
IN1 1
8 NO1
Figure 11. SOT23 Pin Assignments (Top View)
IN1 1
8 NO1
V+ 2
7 COM1
IN1 1
V+ 2
6 IN2
COM2 4
V+ 2
AS1742
AS1741
NO2 3
7 COM1
5 GND
NC2 3
AS1743
6 IN2
COM2 4
7 COM1
5 GND
NC2 3
COM2 4
6 IN2
5 GND
Pin Descriptions
Table 6. Pin Descriptions
Pin Number
Pin Name
COM1
COM2
GND
See Figure 10
and Figure 11
Description
Analog Switch 1 Common
Analog Switch 2 Common
Ground
IN1
Analog Switch 1 Logic Control Input
IN2
Analog Switch 2 Logic Control Input
NC1
Analog Switch 1 Normally Closed Terminal
NC2
Analog Switch 2 Normally Closed Terminal
NO1
Analog Switch 1 Normally Open Terminal
NO2
Analog Switch 2 Normally Open Terminal
V+
www.austriamicrosystems.com
Input Supply Voltage. +1.6 to +3.6V
Revision 1.76
7 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
ON Resistance
8 Detailed Description
The AS1741/AS1742/AS1743 are low ON-resistance, low-voltage, dual analog SPST switches that operate from a single +1.6 to +3.6V supply.
CMOS process technology allows switching of analog signals that are within the supply voltage range (GND to V+).
ON Resistance
When powered from a +3V supply, the AS1741/AS1742/AS1743 low (0.8Ω, max) ON-resistance allows high-speed,
continuous signals to be switched in a variety of applications. All devices have very low RON flatness (0.18Ω, max) so
they can meet or exceed the low-distortion audio requirements of modern portable audio devices.
Bi-Directional Switching
Pins NOx, NCx, and COMx are bi-directional and can be used as inputs or outputs.
Analog Signal Levels
Analog signals ranging over the entire supply voltage range (V+ to GND) can be passed with very little change in ONresistance (see Typical Operating Characteristics on page 5).
Logic Inputs
The AS1741/AS1742/AS1743 logic inputs can be driven up to +3.6V regardless of the supply voltage value. For example, with a +1.8V supply, INx may be driven low to GND and high to +3.6V. This allows the devices to interface with
+3V systems using a supply of less than 3V.
www.austriamicrosystems.com
Revision 1.76
8 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Power Supply Sequencing
9 Application Information
Power Supply Sequencing
Proper power-supply sequencing is critical for proper switch operation. The power supplies should be started up in the
following sequence:
1. V+
2. NOx, NCx, COMx
Note: Operation beyond the absolute maximum ratings (see page 2) may permanently damage the devices.
Power Supply Bypass
Power supply connections to the devices must maintain a low impedance to ground. This can be done using a bypass
capacitor, which will also improve noise margin and prevent switching noise propagation from the V+ supply to other
components.
A 0.1µF bypass capacitor, connected from V+ to GND (see Figure 17 on page 11), is adequate for most applications.
Logic Inputs
Driving INx Rail-to-Rail will help minimize power consumption.
Layout Considerations
High-speed switches require proper layout and design procedures for optimum performance.
!
!
!
Short, wide traces should be used to reduce stray inductance and capacitance.
Bypass capacitors should be as close to the device as possible.
Large ground planes should be used wherever possible.
Timing Diagrams and Test Setups
Figure 12. AS1741/AS1743 Test Circuit and Timing Diagram
V+
NOx
V+
VNOx
VIH + 0.5V
INx
AS1741/
AS1743
tR < 5ns
tF < 5ns
50%
50%
0
VCOMx
INx
COMx
50Ω
50Ω
35pF
GND
VNOx
VCOMx
0
90%
tON
90%
tOFF
Figure 13. AS1742/AS1743 Test Circuit and Timing Diagram
V+
NCx
V+
VNCx
AS1742/
AS1743
INx
COMx
50Ω
50%
50%
0
VCOMx
INx
tR < 5ns
tF < 5ns
VIH + 0.5V
50Ω
35pF
VNCx
VCOMx
0
90%
90%
GND
tOFF
www.austriamicrosystems.com
Revision 1.76
tON
9 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Timing Diagrams and Test Setups
Figure 14. AS1743 Test Circuit and Timing Diagram
VS
tR < 5ns
tF < 5ns
VIH + 0.5V
VS
NC2
NO1
INx
V+
0
V+
AS1743
VS
COM1
INx
VCOMx
COM2
50Ω
50Ω
90%
90%
VCOMx
0
35pF
GND
tBBM
tBBM
tBBM = tON(NOx) - tOFF(NCx)
or tBBM = tON(NCx) - tOFF(NOx)
Figure 15. Charge Injection
NCx
or
NOx
V+
V+
V+
RGEN
INx
0
VGEN
AS174x
VIN
VIN
AS1741
AS1742
VOUT
COMx
∆VOUT
VOUT
CLOAD
1000pF
50Ω
GND
∆VOUT is the measured voltage due to charge transfer error Q
when the channel turns off.
Q = ∆VOUT x CLOAD
Figure 16. NOx, NCx, and COMx Capacitance
AS1741/
AS1742/
AS1743
V+
V+
COMx
1MHz
Capacitance
Analyzer
As
Required
INx
GND
www.austriamicrosystems.com
NCx or
NOx
Revision 1.76
10 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Timing Diagrams and Test Setups
Figure 17. Off-Isolation, On-Loss, and Crosstalk
Network Analyzer
NOx
or
NCx
V+
V+
0.1µF
AS1741/
AS1742/
AS1743
V+
INx
VIN
50Ω
VOUT
Measure
50Ω
†
COMx
Reference
GND
50Ω
50Ω
†
Use 50Ω termination for off-isolation
Notes:
1. Measurements are standardized against short-circuit at socket terminals.
2. Off-isolation is measured between COMx and the off NCx/NOx terminal of each switch. Off-isolation = 20log(VOUT/VIN).
3. Signal direction through the switch is reversed; worst values are recorded.
www.austriamicrosystems.com
Revision 1.76
11 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
10 Package Drawings and Markings
The devices are available in an 8-pin MSOP package and an 8-pin SOT23 package.
Figure 18. 8-pin MSOP Package
Notes:
1.
2.
3.
4.
5.
6.
7.
All dimensions are in millimeters, angles in degrees, unless otherwise specified.
Datums B and C to be determined at datum plane H.
Dimensions D and E1 are to be determined at datum plane H.
Dimensions D2 and E2 are for top package; dimensions D and E1 are for bottom package.
Cross section A-A to be determined at 0.13 to 0.25mm from lead tip.
Dimensions D and D2 do not include mold flash, protrusion, or gate burrs.
Dimensions E1 and E2 do not include interlead flash or protrusion.
Symbol
A
A1
A2
D
D2
E
E1
E2
E3
E4
R
R1
t1
t2
www.austriamicrosystems.com
Typ
1.10
0.10
0.86
3.00
2.95
4.90
3.00
2.95
0.51
0.51
0.15
0.15
0.31
0.41
±Tol
Max
±0.05
±0.08
±0.10
±0.10
±0.15
±0.10
±0.10
±0.13
±0.13
+0.15/-0.08
+0.15/-0.08
±0.08
±0.08
Symbol
b
b1
c
c1
θ1
θ2
θ3
L
L1
aaa
bbb
ccc
e
S
Revision 1.76
Typ
0.33
0.30
0.18
0.15
3.0º
12.0º
12.0º
0.55
0.95BSC
0.10
0.08
0.25
0.65 BSC
0.525 BSC
±Tol
+0.07/-0.08
±0.05
±0.05
+0.03/-0.02
±3.0º
±3º
±3º
±0.15
-
12 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Figure 19. 8-pin SOT23 Package
Notes:
1. All dimensions are in millimeters.
2. Foot length measured at intercept point between datum A and
lead surface.
3. Package outline exclusive of mold flash and metal burr.
4. Package outline inclusive of solder plating.
5. Complies with EIAJ SC74 (6-lead version).
6. PKGST0005 (Rev B) refer to SOT23 8-lead SOT23-D-2019
(Rev C) package outline.
www.austriamicrosystems.com
Revision 1.76
Symbol
A
A1
A2
b
C
D
E
E1
L
e
e1
α
Min
Max
0.90
1.45
0.00
0.15
0.90
1.30
0.22
0.38
0.09
0.20
2.80
3.10
2.60
3.00
1.50
1.75
0.35
0.55
0.65REF
1.95REf
0º
10º
13 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
11 Ordering Information
The devices are available as the standard products shown in Table 7.
Table 7. Ordering Information
Model
Description
Delivery Form
Package
AS1741G
Dual SPST Switch
Tube
8-pin MSOP
AS1741G-T
Dual SPST Switch
Tape and Reel
8-pin MSOP
Dual SPST Switch
Tape and Reel
8-pin SOT23
AS1742G
Dual SPST Switch
Tube
8-pin MSOP
AS1742G-T
Dual SPST Switch
Tape and Reel
8-pin MSOP
Dual SPST Switch
Tape and Reel
8-pin SOT23
AS1743G
Dual SPST Switch
Tube
8-pin MSOP
AS1743G-T
Dual SPST Switch
Tape and Reel
8-pin MSOP
Dual SPST Switch
Tape and Reel
8-pin SOT23
AS1741H-T
Markings
†
AS1742H-T
AS1743H-T
†
†
ASJL
ASJK
ASJM
Available upon request
www.austriamicrosystems.com
Revision 1.76
14 - 15
austriam i c r o systems
AS1741, AS1742, AS1743
Data Sheet
Copyrights
Copyright © 1997-2005, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe.
Trademarks Registered ®. All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing
in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding
the information set forth herein or regarding the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior
to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information.
This product is intended for use in normal commercial applications. Applications requiring extended temperature
range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or lifesustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for
each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard
production flow, such as test flow or test location.
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However,
austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to
personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or
consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of
austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters
austriamicrosystems AG
A-8141 Schloss Premstaetten, Austria
Tel: +43 (0) 3136 500 0
Fax: +43 (0) 3136 525 01
e-mail: [email protected]
For Sales Offices, Distributors and Representatives, please visit:
http://www.austriamicrosystems.com
austriamicrosystems
www.austriamicrosystems.com
Revision 1.76
– a leap ahead
15 - 15
Similar pages