IRF IR11662S Advanced smart rectifier tm control ic Datasheet

Datasheet No - PD97468
March 23, 2010
IR11662S
ADVANCED SMART RECTIFIER TM CONTROL IC
Product Summary
Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Secondary side high speed SR controller
Topology
DCM, CrCM flyback and Resonant half-bridge
topologies
200V proprietary IC technology
VD
Max 500KHz switching frequency
VOUT
Anti-bounce logic and UVLO protection
4A peak turn off drive current
Io+ & I o- (typical)
Micropower start-up & ultra low quiescent current
Turn on Propagation
10.7V gate drive clamp
Delay
50ns turn-off propagation delay
Vcc range from 11.3V to 20V
Turn off Propagation
Direct sensing of MOSFET drain voltage
Delay
Enable function synchronized with MOSFET VDS
transition
Cycle by Cycle MOT Check Circuit prevents multiple Package Options
false trigger GATE pulses
Lead-free
Compatible with 0.3W Standby, Energy Star, CECP,
etc.
Flyback,
Resonant Half-bridge
200V
10.7V Clamped
+1A & -4A
60ns (typical)
50ns (typical)
Typical Applications
•
LCD & PDP TV, Telecom SMPS, AC-DC adapters,
ATX SMPS, Server SMPS
8-Lead SOIC
Typical Connection Diagram
Vin
Rdc
XFM
Cdc
U1
Cs
1
Ci
2
3
RMOT
4
VCC
VGATE
OVT
GND
MOT
VS
EN
VD
IR11671
IR11662S
Rtn
8
7
6
Co
LOAD
Rs
5
Rg
Q1
*Please note that this datasheet contains advance information that could change before the product is
released to production.
www.irf.com
© 2010 International Rectifier
IR11662S
Table of Contents
Page
Description
3
Qualification Information
4
Absolute Maximum Ratings
5
Electrical Characteristics
6
Functional Block Diagram
8
Input/Output Pin Equivalent Circuit Diagram
9
Lead Definitions
10
Lead Assignments
10
Application Information and Additional Details
12
Package Details
22
Tape and Reel Details
23
Part Marking Information
24
Ordering Information
25
www.irf.com
© 2010 International Rectifier
2
IR11662S
Description
IR11662 is a smart secondary-side driver IC designed to drive N-Channel power MOSFETs used as
synchronous rectifiers in isolated Flyback and resonant half-bridge converters. The IC can control one or
more paralleled N-MOSFETs to emulate the behavior of Schottky diode rectifiers. The drain to source voltage
is sensed differentially to determine the polarity of the current and turn the power switch on and off in
proximity of the zero current transition. The cycle-by-cycle MOT protection circuit can automatically detect no
load condition and turn off gate driver output to avoid negative current flowing through the MOSFETs.
Ruggedness and noise immunity are accomplished using an advanced blanking scheme and double-pulse
suppression which allow reliable operation in all operating modes.
www.irf.com
© 2010 International Rectifier
3
IR11662S
Qualification Information†
Qualification Level
Moisture Sensitivity Level
Machine Model
ESD
Human Body Model
IC Latch-Up Test
RoHS Compliant
Industrial††
Comments: This family of ICs has passed JEDEC’s
Industrial qualification. IR’s Consumer qualification level is
granted by extension of the higher Industrial level.
MSL2††† 260°C
(per IPC/JEDEC J-STD-020)
Class B
(per JEDEC standard JESD22-A115)
Class 1C (1500V)
(per EIA/JEDEC standard EIA/JESD22-A114)
Class I, Level A
(per JESD78)
Yes
†
††
Qualification standards can be found at International Rectifier’s web site http://www.irf.com/
Higher qualification ratings may be available should the user have such requirements. Please contact your
International Rectifier sales representative for further information.
††† Higher MSL ratings may be available for the specific package types listed here. Please contact your
International Rectifier sales representative for further information.
www.irf.com
© 2010 International Rectifier
4
IR11662S
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All
voltage parameters are absolute voltages referenced to COM, all currents are defined positive into any lead.
The thermal resistance and power dissipation ratings are measured under board mounted and still air
conditions.
Parameters
Supply Voltage
Enable Voltage
Cont. Drain Sense Voltage
Pulse Drain Sense Voltage
Source Sense Voltage
Gate Voltage
Operating Junction Temperature
Storage Temperature
Thermal Resistance
Package Power Dissipation
Switching Frequency
Symbol
VCC
VEN
VD
VD
VS
VGATE
TJ
TS
R JA
PD
fsw
Min.
-0.3
-0.3
-1
-5
-3
-0.3
-40
-55
Max.
20
20
200
200
20
20
150
150
128
970
500
Units
V
V
V
V
V
V
°C
°C
°C/W
mW
kHz
Remarks
VCC=20V, Gate off
SOIC-8
SOIC-8, TAMB=25°C
Recommended Operating Conditions
For proper operation the device should be used within the recommended conditions.
Symbol
Definition
VCC
Supply voltage
VD
Drain Sense Voltage
Junction Temperature
TJ
Fsw
Switching Frequency
† VD -3V negative spike width ≤100ns
Min.
11.4
†
-3
-25
---
Max.
18
200
125
500
Units
Min.
5
Max.
75
Units
kΩ
V
°C
kHz
Recommended Component Values
Symbol
RMOT
Component
MOT pin resistor value
www.irf.com
© 2010 International Rectifier
5
IR11662S
Electrical Characteristics
VCC=15V and TA = 25°C unless otherwise specified. The output voltage and current (VO and IO) parameters
are referenced to GND (pin7).
Supply Section
Parameters
Supply Voltage Operating
Range
VCC Turn On Threshold
VCC Turn Off Threshold
(Under Voltage Lock Out)
VCC Turn On/Off Hysteresis
Operating Current
Symbol
Min.
VCC
VCC ON
VCC UVLO
Max.
Units
11.4
9.8
10.55
18
11.3
V
V
8.4
9
9.7
V
1.55
8.5
50
1.8
100
150
2.70
1.6
1.5
10
65
2.2
200
200
3.2
2.0
V
mA
mA
mA
µA
µA
V
V
M
VCC HYST
ICC
Quiescent Current
Start-up Current
Sleep Current
Enable Voltage High
Enable Voltage Low
Enable Pull-up Resistance
IQCC
ICC START
I SLEEP
VENHI
VENLO
REN
Comparator Section
Parameters
Symbol
Turn-off Threshold
Typ.
VTH1
2.15
1.2
Min.
-7
-15
-23
-150
Typ.
-3.5
-10.5
-19
Max.
0
-7
-15
-50
Units
mV
GBD
Remarks
OVT = 0V, VS=0V
OVT floating, VS=0V
OVT = VCC, VS=0V
VCM
-0.15
One-Shot Section
Parameters
Blanking pulse duration
Symbol
tBLANK
Min.
8
Typ.
15
2.5
5.4
40
Max.
24
Units
Remarks
µs
V
VCC=10V – GBD
V
VCC=20V – GBD
mV VCC=10V – GBD
Min.
180
2.25
Typ.
240
3
Max.
300
3.75
Units
Remarks
ns
RMOT =5k VCC=12V
µs
RMOT =75k VCC=12V
Hysteresis
VHYST3
Minimum On Time Section
Parameters
Symbol
Minimum on time
TOnmin
www.irf.com
V
VCC=VCC ON - 0.1V
VEN=0V, VCC =15V
Input CM Voltage Range
VTH3
2
CLOAD = 1nF, fSW = 400kHz
CLOAD = 10nF, fSW = 400kHz
VTH2
VHYST
IIBIAS1
IIBIAS2
VOFFSET
Reset Threshold
7.5
100
2
GBD
Turn-on Threshold
Hysteresis
Input Bias Current
Input Bias Current
Comparator Input Offset
55
1
30
mV
mV
µA
µA
mV
Remarks
VD = -50mV
VD = 200V
GBD
© 2010 International Rectifier
6
IR11662S
Electrical Characteristics
VCC=15V and TA = 25°C unless otherwise specified. The output voltage and current (VO and IO) parameters
are referenced to GND (pin7).
Gate Driver Section
Parameters
Gate Low Voltage
Gate High Voltage
Rise Time
Symbol
VGLO
VGTH
tr1
tr2
Fall Time
tf1
tf2
Turn on Propagation Delay
tDon
Turn off Propagation Delay
tDoff
Pull up Resistance
rup
Pull down Resistance
rdown
Output Peak Current(source) IO source
Output Peak Current (sink)
IO sink
Min.
9.0
Typ.
0.3
10.7
21
181
10
44
60
50
5
1.2
1
4
www.irf.com
Max.
0.5
12.5
95
75
Units
V
V
ns
ns
ns
ns
ns
ns
A
A
Remarks
IGATE = 200mA
VCC=12V-18V (internally clamped)
CLOAD = 1nF, VCC=12V
CLOAD = 10nF, VCC=12V
CLOAD = 1nF, VCC=12V
CLOAD = 10nF, VCC=12V
VDS to VGATE -100mV overdrive
VDS to VGATE -100mV overdrive
IGATE = 1A – GBD
IGATE = -200mA
CLOAD = 10nF – GBD
CLOAD = 10nF – GBD
© 2010 International Rectifier
7
IR11662S
Functional Block Diagram
MOT
VCC
VCC
UVLO
&
REGULATOR
EN
Cycle by Cycle
MOT Check
Circuit
VCC
VD
Min ON Time
VTH1
RESET
VS
VGATE
DRIVER
GND
OVT
Min OFF Time
Vgate
RESET
VTH3
VTH2
www.irf.com
VTH1
VTH3
VDS
© 2010 International Rectifier
8
IR11662S
I/O Pin Equivalent Circuit Diagram
VD
ESD
Diode
RESD
200V
Diode
GND
www.irf.com
© 2010 International Rectifier
9
IR11662S
Lead Definitions
PIN#
1
2
3
4
5
6
7
8
Symbol
VCC
OVT
MOT
EN
VD
VS
GND
VGATE
Description
Supply Voltage
Offset Voltage Trimming
Minimum On Time
Enable
FET Drain Sensing
FET Source Sensing
Ground
Gate Drive Output
Lead Assignments
1
VCC
VGATE
8
2
OVT
GND
7
3
MOT
VS
6
4
EN
VD
www.irf.com
5
© 2010 International Rectifier
10
IR11662S
Detailed Pin Description
VCC: Power Supply
This is the supply voltage pin of the IC and it is monitored by the under voltage lockout circuit. It is possible to
turn off the IC by pulling this pin below the minimum turn off threshold voltage, without damage to the IC.
To prevent noise problems, a bypass ceramic capacitor connected to Vcc and COM should be placed as
close as possible to the IR11662. This pin is internally clamped.
OVT: Offset Voltage Trimming
The OVT pin will program the amount of input offset voltage for the turn-off threshold VTH1.
The pin can be optionally tied to ground, to VCC or left floating, to select 3 ranges of input offset trimming.
This programming feature allows for accommodating different RDson MOSFETs.
MOT: Minimum On Time
The MOT programming pin controls the amount of minimum on time. Once VTH2 is crossed for the first time,
the gate signal will become active and turn on the power FET. Spurious ringings and oscillations can trigger
the input comparator off. The MOT blanks the input comparator keeping the FET on for a minimum time.
The MOT is programmed between 200ns and 3us (typ.) by using a resistor referenced to COM.
EN: Enable
This pin is used to activate the IC “sleep” mode by pulling the voltage level below 1.6V (typ). In sleep mode
the IC will consume a minimum amount of current. All switching functions will be disabled and the gate will be
inactive.
VD: Drain Voltage Sense
VD is the voltage sense pin for the power MOSFET Drain. This is a high voltage pin and particular care must
be taken in properly routing the connection to the power MOSFET drain.
Additional filtering and or current limiting on this pin are not recommended as it would limit switching
performance of the IC.
VS: Source Voltage Sense
VS is the differential sense pin for the power MOSFET Source. This pin must not be connected directly to the
power ground pin (7) but must be used to create a Kelvin contact as close as possible to the power MOSFET
source pin.
GND: Ground
This is ground potential pin of the integrated control circuit.
referenced to this point.
The internal devices and gate driver are
VGATE: Gate Drive Output
This is the gate drive output of the IC. Drive voltage is internally limited and provides 1A peak source and 4A
peak sink capability. Although this pin can be directly connected to the power MOSFET gate, the use of
minimal gate resistor is recommended, especially when putting multiple FETs in parallel.
Care must be taken in order to keep the gate loop as short and as small as possible in order to achieve
optimal switching performance.
www.irf.com
© 2010 International Rectifier
11
IR11662S
Application Information and Additional Details
State Diagram
UVLO/Sleep Mode
The IC remains in the UVLO condition until the voltage on the VCC pin exceeds the VCC turn on threshold
voltage, VCC ON. During the time the IC remains in the UVLO state, the gate drive circuit is inactive and the IC
draws a quiescent current of ICC START. The UVLO mode is accessible from any other state of operation
whenever the IC supply voltage condition of VCC < VCC UVLO occurs.
The sleep mode is initiated by pulling the EN pin below 1.6V (typ). In this mode the IC is essentially shut
down and draws a very low quiescent supply current.
Normal Mode and Synchronized Enable Function
The IC enters in normal operating mode once the UVLO voltage has been exceeded and the EN voltage is
above VENHI threshold. When the IC enters the Normal Mode from the UVLO Mode, the GATE output is
disabled (stays low) until VDS exceeds VTH3 to activate the gate. This ensures that the GATE output is not
enabled in the middle of a switching cycle. This logic prevents any reverse currents across the device due to
the minimum on time function in the IC. The gate will continuously drive the SR MOSFET after this one-time
activation. The Cycle by Cycle MOT protection circuit is enabled in Normal Mode.
MOT Protection Mode
If the secondary current conduction time is shorter than the MOT (Minimum On Time) setting, the next driver
output is disabled. This function can avoid reverse current that occurs when the system works at very low
duty-cycles or at very light/no load conditions and reduce system standby power consumption by disabling
GATE outputs. The Cycle by Cycle MOT Check circuit is always activated under Normal Mode and MOT
Protection Mode, so that the IC can automatically resume normal operation once the load increases to a level
and the secondary current conduction time is longer than MOT.
www.irf.com
© 2010 International Rectifier
12
IR11662S
General Description
The IR11662 Smart Rectifier IC can emulate the operation of diode rectifier by properly driving a
Synchronous Rectifier (SR) MOSFET. The direction of the rectified current is sensed by the input comparator
using the power MOSFET RDson as a shunt resistance and the GATE pin of the MOSFET is driven
accordingly.
Internal blanking logic is used to prevent spurious transitions and guarantee operation in continuous (CCM),
discontinuous (DCM) and critical (CrCM) conduction mode.
IR11662 is suitable for Flyback and Resonant Half-Bridge topologies.
VGate
VDS
VTH2
VTH1
VTH3
Figure 1: Input comparator thresholds
Flyback Application
The modes of operation for a Flyback circuit differ mainly for the turn-off phase of the SR switch, while the
turn-on phase of the secondary switch (which corresponds to the turn off of the primary side switch) is
identical.
Turn-on phase
When the conduction phase of the SR FET is initiated, current will start flowing through its body diode,
generating a negative VDS voltage across it. The body diode has generally a much higher voltage drop than
the one caused by the MOSFET on resistance and therefore will trigger the turn-on threshold VTH2.
At that point the IR11662 will drive the gate of MOSFET on which will in turn cause the conduction voltage
VDS to drop down. This drop is usually accompanied by some amount of ringing, that can trigger the input
comparator to turn off; hence, a Minimum On Time (MOT) blanking period is used that will maintain the
power MOSFET on for a minimum amount of time.
The programmed MOT will limit also the minimum duty cycle of the SR MOSFET and, as a consequence, the
max duty cycle of the primary side switch.
DCM/CrCM Turn-off phase
Once the SR MOSFET has been turned on, it will remain on until the rectified current will decay to the level
where VDS will cross the turn-off threshold VTH1. This will happen differently depending on the mode of
operation.
In DCM the current will cross the threshold with a relatively low dI/dt. Once the threshold is crossed, the
current will start flowing again thru the body diode, causing the VDS voltage to jump negative. Depending on
the amount of residual current, VDS may trigger once again the turn on threshold: for this reason VTH2 is
blanked for a certain amount of time (TBLANK) after VTH1 has been triggered.
The blanking time is internally set. As soon as VDS crosses the positive threshold VTH3 also the blanking time
is terminated and the IC is ready for next conduction cycle.
www.irf.com
© 2010 International Rectifier
13
IR11662S
IPRIM
VPRIM
T1
time
T3
T2
ISEC
VSEC
time
Figure 2: Primary and secondary currents and voltages for DCM mode
IPRIM
VPRIM
T1
time
T2
ISEC
VSEC
time
Figure 3: Primary and secondary currents and voltages for CrCM mode
CCM Turn-off phase
In CCM mode the turn off transition is much steeper and dI/dt involved is much higher. The turn on phase is
identical to DCM or CrCM and therefore won’t be repeated here.
During the SR FET conduction phase the current will decay linearly, and so will VDS on the SR FET.
Once the primary switch will start to turn back on, the SR FET current will rapidly decrease crossing VTH1
and turning the gate off. The turn off speed is critical to avoid cross conduction on the primary side and
reduce switching losses.
Also in this case a blanking period will be applied, but given the very fast nature of this transition, it will be
reset as soon as VDS crosses VTH3.
www.irf.com
© 2010 International Rectifier
14
IR11662S
IPRIM
VPRIM
T1
time
T2
ISEC
VSEC
time
Figure 4: Primary and secondary currents and voltages for CCM mode
The operation waveforms of IR11662 in a flyback converter under CCM mode and DCM/CrCM were shown
in Figure 5 and Figure 6 respectively.
VTH3
ISEC
VDS
T1
T2
time
VTH1
VTH2
Gate Drive
time
Blanking
time
MOT
Figure 5: Secondary side CCM operation
www.irf.com
© 2010 International Rectifier
15
IR11662S
VTH3
ISEC
VDS
T1
T2
time
VTH1
VTH2
Gate Drive
time
Blanking
MOT
10us blanking
Figure 6: Secondary side DCM/CrCM operation
Resonant Half-Bridge Application
The typical application circuit of IR11662 in LLC half-bridge is shown in Figure 7.
M3
Rcc1
CVCC1
Rg1
Vin
M1
Lr
M2
T1
Rmot1
1
2
3
4
VCC
OVT
MOT
EN
GATE
GND
VS
VD
8
7
6
5
IR11662
Lm
Cr
VOUT
Rcc2
CVCC2
Rtn
1
2
3
4
Rmot2
VCC
OVT
MOT
EN
GATE
GND
VS
VD
8
7
6
5
Cout
Rg2
IR11662
M4
Figure 7: Resonant half-bridge application circuit
In resonant half-bridge converter, the turn-on phase and turn-off phase is similar to Flyback except the
current shape is sinusoid. The typical operation waveform can be found below.
www.irf.com
© 2010 International Rectifier
16
IR11662S
Figure 8: Resonant half-bridge operation waveform
MOT Protection Mode
The MOT protection prevents reverse current in SR MOSFET which could happen at light load if the MOT
time is set very long. The IC disables the gate output in the protection mode and automatically resume to
normal operation as the load increasing to a level where the SR current conduction time is longer than MOT.
This function works in both flyback and resonant half-bridge topologies. Figure 9 is an example in Flyback
converter.
Figure 9: MOT Protection Mode
www.irf.com
© 2010 International Rectifier
17
IR11662S
Synchronized Enable Function
Sync Enable function guarantees the VGATE always starts switching at the beginning of a switching cycle.
This function works in both flyback and resonant half-bridge topologies. Figure 10 is an example in resonant
half-bridge converter.
Figure 10: Synchronized Enable Function (resonant half-bridge)
General Timing Waveform
VCC
VCC ON
VCC UVLO
t
UVLO
NORMAL
UVLO
Figure 11: Vcc UVLO
VTH1
VDS
VTH2
t Don
t Doff
VGate
90%
50%
10%
t rise
tfall
Figure 12: Timing waveform
www.irf.com
© 2010 International Rectifier
18
IR11662S
11 V
VCC UVLO Thresholds
ISUPPLY (mA)
10
1
0.1
10 V
9V
VCC ON
VCC UVLO
0.01
5V
10 V
15 V
Supply voltage
8V
-50 °C
20 V
IQCC
ICC Supply Current (mA)
ICC Supply Current (mA)
8.5
1.5
1.0
-50 °C
0 °C
50 °C
100 °C
50 °C
100 °C
Temperature
150 °C
Figure 14: Undervoltage Lockout vs.
Temperature
Figure 13: Supply Current vs. Supply Voltage
2.0
0 °C
8.0
7.5
-50 °C
150 °C
Icc @400KHz, CLOAD=1nF
0 °C
50 °C
100 °C
150 °C
Temperature
Temperature
Figure 16: Icc Supply Currrent @1nF Load vs.
Temperature
Figure 15: Icc Quiescent Currrent vs.
Temperature
www.irf.com
© 2010 International Rectifier
19
IR11662S
0.0
0.0
-10.0
-50.0
VTH2 Thresholds (mV)
VTH1 Threshold (mV)
-5.0
-15.0
-20.0
OVT=GND
OVT=Floating
OVT=VCC
-25.0
-150.0
-50 °C
-30.0
-50 °C
-100.0
0 °C
50 °C
100 °C
Temperature
0 °C
150 °C
50 °C
100 °C
150 °C
Temperature
Figure 18: VTH2 vs. Temperature
Figure 17: VTH1 vs. Temperature
-6.0
100.0
VTH1 Threshold (mV)
Comparator Hysteresis VHYST (mV)
VS=-150mV
75.0
50.0
-50 °C
0 °C
50 °C
100 °C
Temperature
Figure 19: Comparator Hysteresis vs.
Temperature
VS=+2V
-12.0
-15.0
-50 °C
150 °C
VS=0V
-9.0
0 °C
50 °C
Temperature
100 °C
150 °C
Figure 20: VTH1 vs. Temperature at Common
Mode (OVT=Floating)
www.irf.com
© 2010 International Rectifier
20
IR11662S
4 us
-50.0
Minimum On Time (us)
VTH2 Threshold (mV)
3 us
-100.0
VS=-150mV
VS=0V
VS=+2V
-150.0
-50 °C
0 °C
50 °C
Temperature
100 °C
2 us
RMOT=5k
RMOT=75k
1 us
0 us
-50 °C
150 °C
50 °C
100 °C
Temperature
150 °C
Figure 22: MOT vs Temperature
Figure 21: VTH2 vs. Temperature at
Common Mode
75 ns
3.0 V
70 ns
2.5 V
Propagation Delay
Enable Thresholds
0 °C
VEN HI
2.0 V
VEN LO
1.5 V
65 ns
Turn-on Propagation Delay
Turn-off Propagation Delay
60 ns
55 ns
50 ns
45 ns
40 ns
1.0 V
-50 °C
0 °C
50 °C
Temperature
100 °C
35 ns
-50 °C
150 °C
0 °C
50 °C
100 °C
150 °C
Temperature
Figure 23: Enable Threshold vs. Temperature
Figure 24: Turn-on and Turn-off Propagation
Delay vs. Temperature
www.irf.com
© 2010 International Rectifier
21
IR11662S
Package Details: SOIC8N
www.irf.com
© 2010 International Rectifier
22
IR11662S
Tape and Reel Details: SOIC8N
LOADED TAPE FEED DIRECTION
A
B
H
D
F
C
NOTE : CONTROLLING
DIM ENSION IN M M
E
G
CARRIER TAPE DIMENSION FOR
Metric
Code
Min
Max
A
7.90
8.10
B
3.90
4.10
C
11.70
12.30
D
5.45
5.55
E
6.30
6.50
F
5.10
5.30
G
1.50
n/a
H
1.50
1.60
8SOICN
Imperial
Min
Max
0.311
0.318
0.153
0.161
0.46
0.484
0.214
0.218
0.248
0.255
0.200
0.208
0.059
n/a
0.059
0.062
F
D
C
B
A
E
G
H
REEL DIMENSIONS FOR 8SOICN
Metric
Code
Min
Max
A
329.60
330.25
B
20.95
21.45
C
12.80
13.20
D
1.95
2.45
E
98.00
102.00
F
n/a
18.40
G
14.50
17.10
H
12.40
14.40
Imperial
Min
Max
12.976
13.001
0.824
0.844
0.503
0.519
0.767
0.096
3.858
4.015
n/a
0.724
0.570
0.673
0.488
0.566
www.irf.com
© 2010 International Rectifier
23
IR11662S
Part Marking Information
www.irf.com
© 2010 International Rectifier
24
IR11662S
Ordering Information
Standard Pack
Base Part Number
IR11662S
Package Type
SOIC8N
Complete Part Number
Form
Quantity
Tube/Bulk
95
IR11662SPBF
Tape and Reel
2500
IR11662STRPBF
The information provided in this document is believed to be accurate and reliable. However, International Rectifier assumes no
responsibility for the consequences of the use of this information. International Rectifier assumes no responsibility for any infringement
of patents or of other rights of third parties which may result from the use of this information. No license is granted by implication or
otherwise under any patent or patent rights of International Rectifier. The specifications mentioned in this document are subject to
change without notice. This document supersedes and replaces all information previously supplied.
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105
www.irf.com
© 2010 International Rectifier
25
Similar pages