MICROWAVE CORPORATION HMC288MS8 v00.0600 2 dB LSB GaAs MMIC 3-BIT DIGITAL ATTENUATOR, 0.7 - 3.7 GHz ATTENUATORS - SMT 9 Typical Applications Features The HMC288MS8 is ideal for: 2 dB LSB Steps to 14 dB • Cellular Single Positive Control Per BIT • PCS, ISM, MMDS Monotonic: ±03 dB Bit Error Typical • WLL applications Miniature MSOP-8 Package, 14.8mm2 Functional Diagram General Description The HMC288MS8 is a broadband 3-bit positive control GaAs IC digital attenuator in an 8 lead MSOP surface mount plastic package. Covering 0.7 to 3.7 GHz, the insertion loss is typically less than 1.2 to 1.8 dB. The attenuator bit values are 2 (LSB), 4, and 8 dB for a total attenuation of 14 dB. Accuracy is excellent at ± 0.3 dB typical with an IIP3 of up to +51 dBm. Three bit control voltage inputs, toggled between 0 and +3 to +5V, are used to select each attenuation state at less than 50 uA each. A single Vdd bias of +3 to +5V applied through an external 5K Ohm resistor is required while occupying less than 14.8 mm². Electrical Specifications, TA = +25° C, Vdd = +3V to +5V & Vctl = 0/Vdd (Unless Otherwise Stated) Parameter Frequency Min. Typical Max. Units 1.4 1.7 2.0 2.3 dB dB dB dB Insertion Loss 0.7 - 1.4 GHz 1.4 - 2.3 GHz 2.3 - 2.7 GHz 2.7 - 3.7 GHz 1.0 1.3 1.5 1.7 Attenuation Range 0.7 - 3.7 GHz 14 dB Return Loss (RF1 & RF2, All Atten. States) 0.7 - 1.4 GHz 1.4 - 2.3 GHz 2.3 - 2.7 GHz 2.7 - 3.7 GHz 17 15 14 12 dB dB dB dB 0.7 - 1.4 GHz 1.4 - 2.3 GHz 2.3 - 2.7 GHz 2.7 - 3.7 GHz ± 0.3 + 3% of Atten. Setting Max ± 0.2 + 3% of Atten. Setting Max ± 0.3 + 3% of Atten. Setting Max ± 0.3 + 4% of Atten. Setting Max dB dB dB dB 14 11 10 9 Attenuation Accuracy: (Referenced to Insertion Loss) All Attenuation States All Attenuation States All Attenuation States All Attenuation States Input Power for 0.1 dB Compression 5V 3V 0.7 - 3.7 GHz 25 22 dBm dBm Input Third Order Intercept Point (Two-tone Input Power = 0dBm Each Tone) 5V 3V 0.7 - 3.7 GHz 51 47 dBm dBm 560 600 ns ns Switching Characteristics tRISE, tFALL (10/90% RF) tON, tOFF (50% CTL to 10/90% RF) 9 - 26 0.7 - 3.7 GHz For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com HMC288MS8 v00.0600 MICROWAVE CORPORATION 2 dB LSB GaAs MMIC 3-BIT DIGITAL ATTENUATOR, 0.7 - 3.7 GHz Return Loss RF1, RF2 Insertion Loss (Only Major States are Shown) 0 0 9 -40 C -0.5 -5 -1.5 -2 +85 C -2.5 2 dB 14 dB -10 -15 -3 -20 -3.5 4 dB -4 0.5 1 1.5 2 2.5 3 3.5 -25 0.5 4 1 8 dB 1.5 FREQUENCY (GHz) 2.5 3 3.5 4 Absolute Bit Error vs. Attenuation State Normalized Attenuation (Only Major States are Shown) 0 1.5 -2 1.2 -4 -6 2 dB BIT ERROR (dB) NORMALIZED ATTENUATION (dB) 2 FREQUENCY (GHz) 4 dB -8 -10 14 dB -12 3.5 GHz 0.9 1.9 GHz 2.4 GHz ATTENUATORS - SMT RETURN LOSS (dB) INSERTION LOSS (dB) +25 C -1 0.9 GHz 0.6 8 dB 0.3 -14 -16 0.5 0 1 1.5 2 2.5 3 3.5 4 2 4 FREQUENCY (GHz) 6 8 10 12 14 ATTENUATION STATE (dB) Absolute Bit Error vs. Frequency Relative Phase vs. Frequency (Only Major States are Shown) (Only Major States are Shown) 1.5 60 8 dB RELATIVE PHASE (deg.) BIT ERROR (dB) 1.2 0.9 14 dB 2 dB 8 dB 0.6 4 dB 0.3 14 dB 40 20 0 4 dB 2 dB 0 0.5 1 1.5 2 2.5 FREQUENCY (GHz) 3 3.5 4 -20 0.5 1 1.5 2 2.5 3 3.5 4 FREQUENCY (GHz) Note: All Data Typical Over Voltage (+3V to +5V) & Temperature (-40 to +85 deg. C.). For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 9 - 27 MICROWAVE CORPORATION HMC288MS8 v00.0600 2 dB LSB GaAs MMIC 3-BIT DIGITAL ATTENUATOR, 0.7 - 3.7 GHz Truth Table Control & Bias Voltages Control Voltage Input ATTENUATORS - SMT 9 Attenuation Setting RF1 - RF2 V1 8 dB V2 4 dB V3 2 dB High High High Reference I.L. High High Low 2 dB High Low High 4 dB Low High High 8 dB Low Low Low 14 dB Max. Atten. State Bias Condition Low 0 to +0.2V @ 20 uA Max. High Vdd ± 0.2V @ 50 uA Max Note: Vdd = +3V to 5V ± 0.2V Any combination of the above states will provide an attenuation approximately equal to the sum of the bits selected. Application Circuit DC blocking capacitors C1 & C2 are required on RF1 & RF2. Choose C1 = C2 = 100 ~ 300 pF to allow lowest customer specific frequency to pass with minimal loss. R1 = 5K Ohm is required to supply voltage to the circuit throught either PIN 5 or PIN 8. 9 - 28 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION HMC288MS8 v00.0600 2 dB LSB GaAs MMIC 3-BIT DIGITAL ATTENUATOR, 0.7 - 3.7 GHz Absolute Maximum Ratings Vdd + 0.5 Vdc Bias Voltage (Vdd) +8.0 Vdc Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C RF Input Power (0.7 - 4 GHz) +28 dBm 9 ATTENUATORS - SMT Control Voltage (V1, V2, V3) Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEADFRAME MATERIAL: COPPER ALLOY 3. LEADFRAME PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS MUST BE SOLDERED TO PCB RF GROUND. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 9 - 29 HMC288MS8 v00.0600 MICROWAVE CORPORATION 2 dB LSB GaAs MMIC 3-BIT DIGITAL ATTENUATOR, 0.7 - 3.7 GHz Evaluation Circuit Board ATTENUATORS - SMT 9 * R2 = R3 = R4 = 100 Ohm. These resistors are optional and may be used to enhance decoupling of the RF path from the control inputs. The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads should be connected directly to the ground plane similar to that shown . A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board as shown is available from Hittite Microwave Corporation upon request. List of Material Item Description J1 - J2 PC Mount SMA Connector J3 - J6 DC Pin R1 5k Ohm Resistor, 0402 Chip R2, R3, R4 100 Ohm Resistor, 0402 Chip C1, C2 0402 Chip Capacitor, Select for Lowest Frequency of Operation U1 HMC288MS8 Digital Attenuator PCB* 103141 Evaluation PCB 1.5” x 1.5” *Circuit Board Material: Rogers 4350 9 - 30 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com MICROWAVE CORPORATION v00.0600 HMC288MS8 2 dB LSB GaAs MMIC 3-BIT DIGITAL ATTENUATOR, 0.7 - 3.7 GHz Notes: ATTENUATORS - SMT 9 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 9 - 31