Kemet FA0H104ZF Supercapacitors fa sery Datasheet

Supercapacitors
FA Series
Overview
Applications
FA Series Supercapacitors, also known as Electric DoubleLayer Capacitors (EDLCs), are intended for high energy storage
applications.
Supercapacitors have characteristics ranging from traditional
capacitors and batteries. As a result, supercapacitors can be
used like a secondary battery when applied in a DC circuit.
These devices are best suited for use in low voltage DC hold-up
applications such as embedded microprocessor systems with
flash memory.
Benefits
•
•
•
•
•
Wide range of temperature from -25°C to +70°C
Maintenance free
5.5 VDC and 11.0 VDC
Highly reliable against liquid leakage
Lead-free and RoHS Compliant
Part Number System
FA
0H
104
Z
F
Series
Maximum Operating Voltage
Capacitance Code (F)
Capacitance
Tolerance
Environmental
Z = -20/+80%
F = Lead-free
FA
0H = 5.5 VDC
1A = 11.0 VDC
First two digits represent
significant figures. Third digit
specifies number of zeros.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
One world. One KEMET
S6018_FA • 3/7/2014
1
Supercapacitors – FA Series
Dimensions – Millimeters
Sleeve
-
○
2.0 Maximum
ℓ Maximum
H Maximum
ø D ± 0.5
+
○
P ± 0.5
d1 ± 0.1
(Terminal)
d2 ± 0.1
Part Number
øD
H
P
ℓ
d1
d2
FA0H473ZF
FA0H104ZF
FA0H224ZF
FA0H474ZF
FA0H105ZF
FA1A223ZF
FA1A104ZF
FA1A224ZF
FA1A474ZF
16.0
21.5
28.5
36.5
44.5
16.0
28.5
36.5
44.5
15.5
15.5
16.5
16.5
18.5
25.0
25.5
27.5
28.5
5.1
7.6
10.2
15.0
20.0
5.1
10.2
15.0
20.0
5.0
5.5
9.5
9.5
9.5
5.0
9.5
9.5
9.5
0.4
0.6
0.6
0.6
1.0
0.4
0.6
1.0
1.0
1.2
1.2
1.4
1.7
1.4
1.2
1.4
1.4
1.4
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
2
Supercapacitors – FA Series
Performance Characteristics
Supercapacitors should not be used for applications such as ripple absorption because of their high internal resistance (several
hundred mΩ to a hundred Ω) compared to aluminum electrolytic capacitors. Thus, its main use would be similar to that of secondary
battery such as power back-up in DC circuit. The following list shows the characteristics of supercapacitors as compared to aluminum
electrolytic capacitors for power back-up and secondary batteries.
Secondary Battery
Capacitor
NiCd
Lithium Ion
Aluminum Electrolytic
Supercapacitor
–
–
–
–
Cd
–
–
–
-20 to +60ºC
-20 to +50ºC
-55 to +105ºC
-40 to +85ºC (FR, FT)
few hours
few hours
few seconds
few seconds
approximately 500 times
approximately 500 to 1,000
times
limitless (*1)
limitless (*1)
yes
yes
none
none
Flow Soldering
not applicable
not applicable
applicable
applicable
Automatic Mounting
not applicable
not applicable
applicable
applicable
(FM and FC series)
leakage, explosion
leakage, combustion,
explosion, ignition
heat-up, explosion
gas emission (*2)
Back-up ability
Eco-hazard
Operating Temperature Range
Charge Time
Charge/Discharge Life Time
Restrictions on Charge/Discharge
Safety Risks
(*1) Aluminum electrolytic capacitors and supercapacitors have limited lifetime. However, when used under proper conditions, both can operate within a
predetermined lifetime.
(*2) There is no harm as it is a mere leak of water vapor which transitioned from water contained in the electrolyte (diluted sulfuric acid). However, application of
abnormal voltage surge exceeding maximum operating voltage may result in leakage and explosion.
Typical Applications
Intended Use (Guideline)
Power Supply (Guideline)
Back-up for 10 seconds or less
1 A and below
Application
Examples of Equipment
Series
Power source of toys,
LED, buzzer
Toys, display device, alarm device
High current supply for a
short amount of time
Actuator, relay solenoid, gas igniter
FA series
Environmental Compliance
All KEMET supercapacitors are RoHS Compliant.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
3
Supercapacitors – FA Series
Table 1 – Ratings & Part Number Reference
Part Number
Maximum
Operating Voltage
(VDC)
FA0H473ZF
FA0H104ZF
Nominal Capacitance
Maximum ESR
@ 1 kHz (Ω)
Maximum
Current @ 30
Minutes (mA)
Weight (g)
0.071
Charge
System (F)
Discharge
System (F)
5.5
0.047
0.075
20.0
0.071
5.5
0.10
0.16
8.0
0.15
0.15
FA0H224ZF
5.5
0.22
0.35
5.0
0.33
0.33
0.71
FA0H474ZF
5.5
0.47
0.75
3.5
0.71
FA0H105ZF
5.5
1.0
1.6
2.5
1.5
1.5
FA1A223ZF
11.0
0.022
0.035
20.0
0.066
0.066
FA1A104ZF
11.0
0.10
0.16
8.0
0.30
0.30
FA1A224ZF
11.0
0.22
0.35
6.0
0.66
0.66
FA1A474ZF
11.0
0.47
0.75
4.0
1.41
1.41
Specifications
Item
FA Type
Test Conditions
(conforming to JIS C 5160-1)
Category Temperature Range
-25ºC to +70ºC
Maximum Operating Voltage
5.5 VDC, 11 VDC
Capacitance
Refer to Table 1
Refer to “Measurement Conditions”
Capacitance Allowance
+80%, -20%
Refer to “Measurement Conditions”
ESR
Refer to Table 1
Measured at 1 kHz, 10 mA; See also
“Measurement Conditions”
Current (30 minutes value)
Refer to Table 1
Refer to “Measurement Conditions”
Surge voltage:
Capacitance
Charge:
Discharge:
Number of cycles:
Series resistance:
ESR
Surge
Current (30 minutes value)
Discharge
resistance:
Temperature:
Appearance
Capacitance
ESR
Capacitance
ESR
Characteristics in Different
Temperature
Phase 2
Phase 3
Capacitance
ESR
≥ 70% of initial value
≤ 300% of initial value
≤ 150% of initial value
Phase 5
≤ 1.5 CV (mA)
Capacitance
Within ±20% of initial value
Current (30 minutes value)
Phase 6
0Ω
70 ±2ºC
+25 ±2ºC
-25 ±2ºC
+25 ±2ºC
+70 ±2ºC
+25 ±2ºC
Satisfy initial ratings
Current (30 minutes value)
ESR
Conforms to 4.17
Phase 1:
Phase 2:
Phase 4:
Phase 5:
Phase 6:
6.3 V (5.5 V type)
12.6 V (11 V type)
30 seconds
9 minutes 30 seconds
1,000
0.047 F
300 Ω
0.10 F
150 Ω
0.22 F
56 Ω
0.47 F
30 Ω
1.0 F, 1.5 F
15 Ω
Satisfy initial ratings
Satisfy initial ratings
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
4
Supercapacitors – FA Series
Specifications cont’d
Item
FA Type
Lead Strength (tensile)
No terminal damage
Conforms to 4.9
Satisfy initial ratings
Conforms to 4.13
Frequency:
Testing Time:
10 to 55 Hz
6 hours
Conforms to 4.11
Solder temp:
Dipping time:
+245 ±5ºC
5 ±0.5 seconds
Capacitance
ESR
Vibration Resistance
Current (30 minutes value)
Appearance
No obvious abnormality
Over 3/4 of the terminal should be covered by the new
solder
Solderability
Test Conditions
(conforming to JIS C 5160-1)
1.6 mm from the bottom should be dipped.
Capacitance
ESR
Solder Heat Resistance
Satisfy initial ratings
Conforms to 4.10
Solder temp:
Dipping time:
No obvious abnormality
1.6 mm from the bottom should be dipped.
Satisfy initial ratings
Conforms to 4.12
Temperature
Condition:
Current (30 minutes value)
Appearance
Capacitance
ESR
Temperature Cycle
Current (30 minutes value)
High Temperature and High
Humidity Resistance
High Temperature Load
Appearance
No obvious abnormality
Capacitance
> 90% of initial value
ESR
≤ 120% of initial ratings
Current (30 minutes value)
≤ 120% of initial ratings
Appearance
No obvious abnormality
Capacitance
> 80% of initial value
ESR
< 120% of initial ratings
Current (30 minutes value)
< 200% of initial ratings
Appearance
No obvious abnormality
Number of cycles:
Conforms to 4.14
Temperature:
Relative humidity:
Testing time:
Conforms to 4.15
Temperature:
Voltage applied:
Series protection
resistance:
Testing time:
+260 ±10ºC
10 ±1 seconds
-25ºC→ Room
temperature→ +70ºC→
Room temperature
5 cycles
+40 ±2ºC
90 to 95% RH
240 ±8 hours
+70 ±2ºC
Maximum operating
voltage
0Ω
1,000 +48 (+48/-0) hours
Marking
Date
code
A1
001
Serial
number
A1
001
Rated voltage
FA
FA
5V
0.1 F
FA
5V
0.1 F
FA
5V
0.1 F
5V
0.1 F
Nominal
capacitance
Negative polarity
identification mark
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
5
Supercapacitors – FA Series
Packaging Quantities
Part Number
Bulk Quantity per Box
FA0H473ZF
FA0H104ZF
FA0H224ZF
FA0H474ZF
FA0H105ZF
FA1A223ZF
FA1A104ZF
FA1A224ZF
FA1A474ZF
400 pieces
90 pieces
50 pieces
30 pieces
20 pieces
240 pieces
50 pieces
30 pieces
20 pieces
List of Plating & Sleeve Type
By changing the solder plating from leaded solder to lead-free solder and the outer tube material of can-cased conventional
supercapacitor from polyvinyl chloride to polyethylene terephthalate (PET), our supercapacitor is now even friendlier to the environment.
a. Iron + copper base + lead-free solder plating (Sn-1Cu)
b. SUS nickel base + copper base + reflow lead-free solder plating (100% Sn, reflow processed)
Series
Part Number
Plating
Sleeve
FA
All FA Types
a
PET (Blue)
Recommended Pb-free solder : Sn / 3.5Ag / 0.75Cu
Sn / 3.0Ag / 0.5Cu
Sn / 0.7Cu
Sn / 2.5Ag / 1.0Bi / 0.5Cu
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
6
Supercapacitors – FA Series
Measurement Conditions
Capacitance (Charge System)
Capacitance is calculated from expression (9) by measuring the charge time constant (τ) of the capacitor (C). Prior to measurement, the
capacitor is discharged by shorting both pins of the device for at least 30 minutes. In addition, use the polarity indicator on the device to
determine correct orientation of capacitor for charging.
Capacitance: C =
τ
Rc
Eo:
(F) (9)
3.0 (V) Product with maximum operating voltage of 3.5 V
5.0 (V) Product with maximum operating voltage of 5.5 V
6.0 (V) Product with maximum operating voltage of 6.5 V
10.0 (V) Product with maximum operating voltage of 11 V
12.0 (V) Product with maximum operating voltage of 12 V
Time from start of charging until Vc becomes 0.632 Eo (V) (seconds)
See table below (Ω).
Switch
Eo
Rc
C
+
–
Charge Resistor Selection Guide
τ:
Rc:
Vc
0.010 F
0.022 F
0.033 F
0.047 F
0.10 F
FYD
FY
FYH
FYL
–
–
–
–
–
5000 Ω
–
1000 Ω
–
1000 Ω 2000 Ω 2000 Ω 2000 Ω 2000 Ω
–
–
–
–
–
–
–
1000 Ω 1000 Ω 1000 Ω 2000 Ω 1000 Ω 2000 Ω 1000 Ω
510 Ω 510 Ω 510 Ω 1000 Ω 510 Ω
–
1000 Ω
0.22 F
200 Ω 200 Ω 200 Ω 510 Ω
510 Ω
–
0.33 F
0.47 F
1.0 F
1.4 F
1.5 F
2.2 F
2.7 F
3.3 F
4.7 F
5.0 F
5.6 F
10.0 F
22.0 F
50.0 F
100.0 F
200.0 F
–
–
–
–
–
100 Ω 100 Ω 100 Ω 200 Ω 200 Ω
51 Ω 51 Ω 100 Ω 100 Ω 100 Ω
–
–
–
200 Ω
–
–
51 Ω
–
–
–
–
–
–
100 Ω
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
100 Ω
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Cap
FA
FE
FS
FR
FM, FME
FMR, FML
FMC
FG
FGR
5000 Ω
–
5000 Ω
2000 Ω
–
2000 Ω
Discharge
–
–
2000 Ω
1000 Ω 2000 Ω
1000 Ω
1000 Ω 1000 Ω
0H: Discharge
510 Ω
–
1000 Ω
0V: 1000 Ω
–
–
Discharge
–
200 Ω
–
–
1000 Ω
100 Ω
–
–
510 Ω
–
–
–
–
–
–
–
510 Ω
–
–
–
200 Ω
–
–
–
–
–
–
–
–
–
–
–
100 Ω
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
FGH
FT
FC, FCS
HV
–
–
–
–
–
–
–
–
Discharge 510 Ω
–
Discharge
–
–
Discharge
–
–
–
–
–
Discharge 200 Ω
Discharge
–
–
–
Discharge 100 Ω
Discharge 100 Ω
–
–
–
–
–
51 Ω
–
–
–
51 Ω
–
–
–
–
–
20 Ω
–
–
–
–
–
–
–
–
–
–
–
Discharge
Discharge
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Discharge
–
–
–
Discharge
–
Discharge
–
–
Discharge
Discharge
Discharge
Discharge
Discharge
*Capacitance values according to the constant current discharge method.
*HV Series capacitance is measured by discharge system
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
7
3.3F
4.7F
5.0F
5.6F
–
–
–
–
–
–
–
–
–
–
100 Ω
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
*Capacitance values according to the constant current discharge method.
*HV series capacitance is measured by discharge system.
Supercapacitors – FA Series
Table 3 Capacitance measurement
–
100 Ω
–
–
51 Ω
–
–
20 Ω
–
–
–
–
–
–
–
–
Measurement Conditions cont’d
Capacitance (Discharge System)
In Capacitance
the (Discharge
diagram below,
charging is performed
for a duration of 30 minutes, once the voltage of the condensor terminal
Capacitance
System)
(Discharge
System:3.5V)
reaches
5.5 V.
As shown
in the
below,
charging
is performed
for aforduration
of 30
onceonce
the voltage
of the
terminal
reaches
In diagram
the diagram
below,
charging
is performed
a duration
of minutes
30 minutes,
the voltage
of capacitor
the capacitor
terminal
reaches 3.5V.
Then,
use
a
constant
current
load
device
and
measure
the
time
for
the
terminal
voltage
to
drop
from
3.0
to
2.5
V
upon
5.5 V. Then, use
a constant
load
deviceload
and device
measure
themeasure
time for the
to drop voltage
from 3.0 to
to drop
2.5 V from
upon 1.8
discharge
Then,
use a current
constant
current
and
theterminal
time forvoltage
the terminal
to 1.5V upon
discharge
at 0.22
mA
F, for
example,
calculate
the static
capacitance
according
to thebelow.
equation
shown below.
at 0.22 mA
perdischarge
0.22
F, forat
example,
calculate
the and
static
capacitance
according
to the equation
shown
1 for
mA0.22
perand
1F,
and
calculate
the
static capacitance
according
to the equation
shown
below.
Note: TheNote:
currentThe
valuecurrent
is 1 mA value
discharged
F.
is 1 per
mA1discharged
per 1F.
I×(T2-T1)I×(T2-T1)
C=
(F)
Capactance:C=
V1-V2
V1-V2
(F)
3.5V
5.5V
V
(V)
SW 0.22mA(I)
A
A
C R
C V
R
3.5V
5.5V
V1
V1
V2
Voltage
SW
V2
V1 : 1.8V
V1 : 3.0V
V2 : 1.5V
V1 : 2.5V
30 min.
T2
T1
Duration (sec.)
T1
Time T2
(sec.)
30 minutes
Capacitance
(Discharge
System:3.5V)
Capacitance
(Discharge
Capacitance
(Discharge
System
– 3.5
V) System:3.5V)
Capacitance
(Discharge
System:3.5V)
Capacitance
(Discharge
System:3.5V)
36 Super
Capacitors (Discharge
Vol.13
System:3.5V)
Capacitance
System:HVseries)
In
the
diagram
below,
charging
is
performed
for
duration
of
30
voltage
of
capacitor
terminal
In diagram
the diagram
below,
charging
is
performed
a duration
of minutes
30 minutes,
once
theonce
voltage
of
the capacitor
terminal
reaches reaches
3.5V.
As shown in the
below,
charging
is
performed
afor
duration
the voltage
ofthe
the
capacitor
terminal
reaches
In the diagram
below, charging
isfor
performed
forofa
a30
duration
of once
30 minutes,
minutes,
once
the
voltage
of the
the
capacitor
terminal
reaches
In the
below,
charging
is
performed
for
a
of
30
minutes,
once
the
voltage
of
capacitor
terminal
reaches
3.5V.
the diagram
diagram
below,
charging
iscurrent
for
a duration
duration
of
30
minutes,
once
the the
voltage
of the
the
capacitor
terminal
reaches
3.5V.
In
diagram
below,
charging
isperformed
performed
for
ameasure
duration
of 30
minutes,
once
the
voltage
ofvoltage
the
capacitor
terminal
reaches
Then,
use
a
constant
load
device
and
measure
the
time
for
terminal
to
drop
from
1.8
to
1.5V
Then,
use
a
constant
current
load
device
and
the
time
for
the
terminal
voltage
to
drop
from
1.8
to
1.5V
upon
3.5 V. Then, use
a constant
current
devicecurrent
and device
measure
themeasure
time
formeasure
the
terminal
voltage
to the
dropterminal
from 1.8voltage
to 1.5
V to
upon
discharge
Then,
use a load
constant
load and
device
and
the
time
for
drop
from
1.8 to
1.5V
Then,
use
a
constant
current
load
the
time
for
the
terminal
voltage
to
drop
from
1.8
to
1.5V
upon
Then,
use
a
constant
current
load
device
and
measure
the
time
for
the
terminal
voltage
to
drop
from
1.8
to
1.5V
upon
Max.
operating
voltage.
discharge
at
1
mA
per
1F,
and
calculate
the
static
capacitance
according
to
the
equation
shown
below.
discharge
at
1
mA
per
1F,
and
calculate
the
static
capacitance
according
to
the
equation
shown
below.
at 1.0 mA per 1.0
F,
for
example,
and
calculate
the
static
capacitance
according
to
the
equation
shown
below.
discharge
at
1
mA
per
1F,
and
calculate
the
static
capacitance
according
to
the
equation
shown
below.
discharge at 1 mA per 1F, and calculate the static capacitance according to the equation shown below.
discharge
atconstant
1 mA percurrent
1F, and
calculate
capacitance
according
to the
equation
shown
below.
Then,
use a
load
device the
andstatic
measure
the time for
the terminal
voltage
to drop
from
2.0 to 1.5V upon discharge
(V)
(V)
(V) below.
(V) shown
at 1 mA per 1F, and calculate the static capacitance according
to
the
equation
(V)
SW
I×(T
I×(T2-T
1) 2-T
-T11))
I×(T
2-T
1) 2(F)
C=
C= I×(T
I×(T
2-T1)
C=
C=
(F)
-V
V
1
2
-V
V
1
2 V -V
C=
V
2 ) 1 (F)2
I×(T
2-T
-V
V11-V
21
C=
(F)
V1-V2
SW
SW
SW
(F)
(F)3.5V
3.5V
3.5V
3.5V V
3.5V V
V
3.5V
V
SW
CV
CV
C
SW
A
A
A
A
A
A
C R
C R
R
C
3.5V
3.5V
(V)
3.5V
V1
V1
V21
3.5V
V
R V2
R V
V12
3.5V
3.5V
V1
V1
V2
V2
V2
R
V2 : 1.5V
T2
T1
T2
T1
T2
T1
minutes
30 minutes 30
30 minutes 30 minutes
30 minutes
T2
T1
Capacitance
(Discharge
System:HVseries)
Capacitance
(Discharge
System:HVseries)
Capacitance
(Discharge
System:HVseries)
V1 : 1.8V
V1 : 1.8V
V2 : 1.5V
V2 : 1.5V
V1 : 1.8V
V1 : 1.8V
V1 : 1.8V
V2 : 1.5V
V2 : 1.5V
1.5V
V12 : 2.0V
Time (sec.)
1
T2
TTime
(sec.)
Time (sec.)
1
T2
TTime
(sec.)
Time (sec.)
Time (sec.)
Capacitance
(Discharge
System:HVseries)
Capacitance
(Discharge
System:HVseries)
Capacitance
(Discharge
System
– HV
Series)
In
the
diagram
below,
charging
is
for
of
the
voltage
of
In the diagram
below,
charging
is performed
for a duration
of 30 minutes,
once theonce
voltage
the capacitor
terminalterminal
reachesre
In
the
diagram
below,
charging
is performed
performed
for a
a duration
duration
of 30
30 minutes,
minutes,
once
the of
voltage
of the
the capacitor
capacitor
terminal
re
In
the
diagram
below,
charging
is
for
of
once
the
of
terminal
series
resistance
(ESR)
As shownEquivalent
in the
diagram
below,
charging
is performed
for
a duration
of 30
minutes
once
the
voltage
of the
capacitor
terminal
reaches
In
theoperating
diagram
below,
charging
is performed
performed
for a
a duration
duration
of 30
30 minutes,
minutes,
once
the voltage
voltage
of the
the capacitor
capacitor
terminal reaches
reaches
Max.
operating
voltage.
Max.
voltage.
Max.
operating
voltage.
Max.
operating
voltage.
maximum operating
voltage.
Then,
use
a constant
current
load
device
andtime
measure
thefor
time for
the terminal
tofrom
drop
fromto2.0
to upon disc
Max.
operating
voltage.
ESR
beconstant
calculated
from
the equation
below.
Then,
use
current
load
device
and
the
time
voltage
to
2.0
Then,shall
use
a
current
load
device
measure
the
for the
voltage
to
dropvoltage
from
2.0
to 1.5V
discharge
Then,
use a
a constant
constant
current
loadand
device
and measure
measure
the
timeterminal
for the
the terminal
terminal
voltage
to drop
drop
from
2.0 upon
to 1.5V
1.5V
upon disc
Then,
use
a
constant
current
load
device
and
measure
the
time
for
the
terminal
voltage
to
drop
from
2.0
to
1.5V
upon
discharge
Then,
use
a
constant
current
load
device
and
measure
the
time
for
the
terminal
voltage
to
drop
from
2.0
to
1.5V
upon
discharge
1.5 V upon discharge
at
1.0
mA
per
1.0
F,
and
calculate
the
static
capacitance
according
to
the
equation
shown
below.
at 11F,
mAand
per calculate
1F, and calculate
static capacitance
according
to the equation
shown below.
at 1 mA per
the staticthe
capacitance
according
to the equation
shown below.
30 minutes
at 1 mAand
per 1F, and calculate
the static capacitance
according
to the equationbelow.
shown below.
at
according
at 1
1 mA
mA per
per 1F,
1F, and calculate
calculate the
the static
static capacitance
capacitance
according to
to the
the equation
equation shown
shown below.
10mA
(V)
(V)
VC
(V)
(V)
ESR=
(Ω)
(V)
SWVC
f:1kHz
C SW
3.5V
SW
3.5V
V1 : 2.0V
0.01
SW
3.5V
A
A
3.5V
SW
I×(T
I×(T2-T
1) 2-T
-T11)) (F)
I×(T
2-T
1) 2(F)
C=
C= I×(T
I×(T
2-T1)
C=
(F)3.5V
C=
(F)
1-V
V1-V2 V
3.5V
C=
(F)22
3.5V
V
1-V2 V1-V
V
1-V2
Current (at 30 minutes after
A
A
A
3.5V V
3.5V V
V
CV
CV
C
charging)
C R
C R
R
3.5V
V1
V1
V21
V
R V2
R V2
V1
V1
V2
V2
V1 : 2.0V
V1 : 2.0V
V2 : 1.5V
V2 : 1.5V
V2 : 1.5V
T1
V1 : 2.0V
V1 : 2.0V
V2 : 1.5V
V2 : 1.5V
T2
Time (sec.)
(sec.)
T2 TTime
T1
Time (sec.)
1
T2
Current shall be calculated from the equation below.
Time
(sec.)
T2
T1
Time (sec.)
T2
T1
minutes
30 minutes 30
30
minutes
30 minutes
Prior to measurement, both lead terminals must be short-circuited for a minimum
of
30
minutes.
30 minutes
Equivalent
series
resistance
(ESR)
The
lead
terminal
connected
to
the
metal
can
case
is
connected
to
the
negative
side of the power supply.
Equivalent
series
resistance
(ESR)
Equivalent
series
resistance
(ESR)
Equivalent Series Resistance (ESR)
Equivalent
Equivalent series
series resistance
resistance (ESR)
(ESR)
ESR
be
the
ESR shall
be shall
calculated
from
thefrom
equation
below. below.
ESR shall be calculated
from
the equation
below.
ESR
be calculated
calculated
the equation
equation
ESR shall
be shall
calculated
from
thefrom
equation
below. below.
ESR 2.5Vdc
shall be(HVseries
calculated50F)
from the equation below.
Eo:
VR
2.7Vdc (HVseries except 50F)
SW
10mA
10mA
10mA
10mA
C
VC(3.5V V
3.0Vdc
type)
V
10mA
C
V
C
(Ω) f:1kHz f:1kHz C
C
ESR= ESR=
VC
VC (Ω)
V
ESR=
f:1kHz C
C
VC
RCCC
ESR=
(Ω)
0.01
V
0.01(5.5V
5.0Vdc
type)(Ω) f:1kHz
ESR=
(Ω)
0.01
f:1kHz
C
V
C
0.01
+
E
O
0.01
Rc:1000Ω (0.010F, 0.022F, 0.047F)
C
-
100Ω (0.10F, 0.22F, 0.47F)
10Ω (1.0F, 1.5F, 2.2F, 4.7F)
Current
(at
30
after
Current
(at
30
minutes
after
charging)
Current
(at
30 minutes
minutes
after charging)
charging)
Current
(at
30
minutes
after
charging)
2.2Ω
(HVseries)
Current
(at
30
minutes
after
charging)
shall
be
calculated
from
the
Current Current
shall
be
calculated
from
the
equation
below. below.
Current
be calculated
from
the equation
equation
below.
Current
shall
be
calculated
from
the
equation
below.
R shall
Current
shallVto
be
calculated
from
the
equation
below.
Prior
measurement,
both
lead
terminals
be
for
of
Prior
to measurement,
both
lead
terminals
must
bemust
short-circuited
for a minimum
of 30 minutes.
Current=
(A)
Prior
to
measurement,
both
lead
terminals
must
be short-circuited
short-circuited
for a
a minimum
minimum
of 30
30 minutes.
minutes.
Prior
to
measurement,
both
lead
terminals
must
be
short-circuited
for
a
minimum
of
minutes.
R•CP.O. Box 5928
© KEMET Electronics
Corporation
• lead
Greenville,
SC 29606
(864)
963-6300
• www.kemet.com
S6018_FA • 3/7/2014
Prior
to measurement,
both
terminals
must
be
short-circuited
for
a negative
minimum
of 30
30
minutes.
The
lead
terminal
connected
to
the
metal
can
case
is
connected
to
the
negative
side
of
the
power
The lead
terminal
connected
to
the
metal
can
case
is
connected
to
the
side
of
the
power
The
lead
terminal
connected
to
the
metal
can
case
is
connected
to
the
negative
side
of
thesupply.
power supply.
supply.
The
lead
terminal
connected
to
the
metal
can
case
is
connected
to
the
negative
side
of
the
power
The lead terminal connected to the metal can case is connected to the negative side of the power supply.
supply.
Self-discharge
characteristic
(0H: 5.5V products)
Eo:(HVseries
2.5Vdc (HVseries
Eo:2.5Vdc
50F) 50F)
Eo:(HVseries
2.5Vdc (HVseries
Eo:2.5Vdc
50F) 50F)
8
ESR shall be calculated from the equation below.
Supercapacitors – FA Series
ESR=
Current (at 30 minutes
after charging)
10mA
VC
Current
shall be
calculated C
from the equation
below.
(Ω)
f:1kHz
VC
0.01 Prior to measurement, both lead terminals must be short-circuited for a minimum of 30 minute
The lead terminal connected to the metal can case is connected to the negative side of the po
Measurement Conditions cont’d
2.5Vdc (HVseries
50F)
Current (at 30Eo:
minutes
after charging)
VR
2.7Vdc (HVseries except 50F)
SW
Current shall be calculated from the equation below.
Current (at 30 minutes after charging)
3.0Vdc (3.5V type)
Prior
to measurement,
both
lead terminals must be short-circuited for a minimum offor
30aminutes.
Current shall be calculated from the
equation
below. Prior
to measurement,
minimum
R
5.0Vdc
(5.5V type) both lead terminals must be short-circuited
The
lead
terminal
connected
to
the
metal
can
case
is
connected
to
the
negative
side
of
the
power
+ supply.
E
of 30 minutes. The lead terminal connected to theRc:
metal
can case
is connected
to the negative side of the power supply.
1000Ω
(0.010F,
0.022F, 0.047F)
C
C
O
-
100Ω (0.10F, 0.22F, 0.47F)
50F)
Eo: 2.5 VDC (HV Series 50 F) Eo:2.5Vdc (HVseries
10Ω (1.0F, 1.5F, 2.2F, 4.7F)
VR
SW
2.7 VDC (HV Series except 50 F) 2.7Vdc (HVseries except 50F)
2.2Ω (HVseries)
3.0 VDC (3.5 V type)
3.0Vdc (3.5V type)
VR
5.0 VDC (5.5 V type)
RC
5.0Vdc (5.5V
type)
Current=
(A)
+
EO
Rc: 1000 Ω (0.010 F, 0.022 F, 0.047
F)
R
C
Rc:1000Ω (0.010F, 0.022F, 0.047F)
C
100 Ω (0.10 F, 0.22 F, 0.47 F)
-
100Ω (0.10F, 0.22F, 0.47F)
10 Ω (1.0 F, 1.5 F, 2.2 F, 4.7 F)
Self-discharge
10Ω (1.0F,
1.5F, 2.2F, 4.7F)characteristic (0H: 5.5V products)
2.2 Ω (HV Series)
2.2Ω (HVseries)
The self-discharge characteristic is measured by charging a voltage of 5.0 Vdc (charge protec
V
Rto the capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measu
Self-Discharge Characteristic (0H
– 5.5 V Products)
Current=
(A)
test should be carried out in an environment with an ambient temperature of 25℃ or belo
RCThe
The self-discharge characteristic is measured by
charging a voltage of 5.0 VDC (charge protection resistance: 0 Ω) according to the
RH or below.
capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measuring the pin-to-pin voltage. The test should be
characteristic
(0H:and
5.5V
products)
carried out in an environmentSelf-discharge
with an ambient temperature
of 25° C or below
relative
humidity of 70% RH or below.
Su
the soldering is checked. The self-discharge characteristic is measured by charging a voltage of 5.0 Vdc (charge protection resistance
to the capacitor polarity for 24 hours, then releasing between the pins for 24 hours and measuring the pin-toThe test should be carried out in an environment with an ambient temperature of 25℃ or below and relative
RH or below.
4. Dismantling
There is a small amount of electrolyte stored within the capacitor. Do not attempt to dismantle as direct skin contact with the electrolyte
will cause burning. This product should be treated as industrial waste and not is not to be disposed of by fire.
Super Capacito
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
9
Supercapacitors – FA Series
Notes on Using Supercapacitors or Electric Double-Layer Capacitors (EDLCs)
1. Circuitry Design
1.1 Useful life
The FC Series Supercapacitor (EDLC) uses an electrolyte in a sealed container. Water in the electrolyte can evaporate while in
use over long periods of time at high temperatures, thus reducing electrostatic capacity which in turn will create greater internal
resistance. The characteristics of the supercapacitor can vary greatly depending on the environment in which it is used. Basic
breakdown mode is an open mode due to increased internal resistance.
1.2 Fail rate in the field
Based on field data, the fail rate is calculated at approximately 0.006 Fit. We estimate that unreported failures are ten times this
amount. Therefore, we assume that the fail rate is below 0.06 Fit.
1.3 Exceeding maximum usable voltage
Performance may be compromised and in some cases leakage or damage may occur if applied voltage exceeds maximum
working voltage.
1.4 Use of capacitor as a smoothing capacitor (ripple absorption)
As supercapacitors contain a high level of internal resistance, they are not recommended for use as smoothing capacitors in
electrical circuits. Performance may be compromised and, in some cases, leakage or damage may occur if a supercapacitor is
used in ripple absorption.
1.5 Series connections
As applied voltage balance to each supercapacitor is lost when used in series connection, excess voltage may be applied to some
supercapacitors, which will not only negatively affect its performance but may also cause leakage and/or damage. Allow ample
margin for maximum voltage or attach a circuit for applying equal voltage to each supercapacitor (partial pressure resistor/voltage
divider) when using supercapacitors in series connection. Also, arrange supercapacitors so that the temperature between each
capacitor will not vary.
1.6 Case Polarity
The supercapacitor is manufactured so that the terminal on the outer case is negative (-). Align the (-) symbol during use. Even
though discharging has been carried out prior to shipping, any residual electrical charge may negatively affect other parts.
1.7 Use next to heat emitters
Useful life of the supercapacitor will be significantly affected if used near heat emitting items (coils, power transistors and posistors,
etc.) where the supercapacitor itself may become heated.
1.8 Usage environment
This device cannot be used in any acidic, alkaline or similar type of environment.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
10
Supercapacitors – FA Series
Notes on Using Supercapacitors or Electric Double-Layer Capacitors (EDLCs) cont’d
2. Mounting
2.1 Mounting onto a reflow furnace
Except for the FC series, it is not possible to mount this capacitor onto an IR / VPS reflow furnace. Do not immerse the capacitor
into a soldering dip tank.
2.2 Flow soldering conditions
See Recommended Reflow Curves in Section – Precautions for Use
2.3 Installation using a soldering iron
Care must be taken to prevent the soldering iron from touching other parts when soldering. Keep the tip of the soldering iron under
400ºC and soldering time to within 3 seconds. Always make sure that the temperature of the tip is controlled. Internal capacitor
resistance is likely to increase if the terminals are overheated.
2.4 Lead terminal processing
Do not attempt to bend or polish the capacitor terminals with sand paper, etc. Soldering may not be possible if the metallic plating
is removed from the top of the terminals.
2.5 Cleaning, Coating, and Potting
Except for the FM series, cleaning, coating and potting must not be carried out. Consult KEMET if this type of procedure is
necessary. Terminals should be dried at less than the maximum operating temperature after cleaning.
3. Storage
3.1 Temperature and humidity
Make sure that the supercapacitor is stored according to the following conditions: Temperature: 5 – 35ºC (Standard 25ºC),
Humidity: 20 – 70% (Standard: 50%). Do not allow the build up of condensation through sudden temperature change.
3.2 Environment conditions
Make sure there are no corrosive gasses such as sulfur dioxide, as penetration of the lead terminals is possible. Always store this
item in an area with low dust and dirt levels. Make sure that the packaging will not be deformed through heavy loading, movement
and/or knocks. Keep out of direct sunlight and away from radiation, static electricity and magnetic fields.
3.3 Maximum storage period
This item may be stored up to one year from the date of delivery if stored at the conditions stated above.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
11
Supercapacitors – FA Series
KEMET Corporation
World Headquarters
Europe
Asia
Southern Europe
Paris, France
Tel: 33-1-4646-1006
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
Sasso Marconi, Italy
Tel: 39-051-939111
Shenzhen, China
Tel: 86-755-2518-1306
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Corporate Offices
Fort Lauderdale, FL
Tel: 954-766-2800
Kamen, Germany
Tel: 49-2307-438110
North America
Northern Europe
Bishop’s Stortford, United Kingdom
Tel: 44-1279-460122
2835 KEMET Way
Simpsonville, SC 29681
Southeast
Lake Mary, FL
Tel: 407-855-8886
Espoo, Finland
Tel: 358-9-5406-5000
Northeast
Wilmington, MA
Tel: 978-658-1663
Beijing, China
Tel: 86-10-5829-1711
Shanghai, China
Tel: 86-21-6447-0707
Taipei, Taiwan
Tel: 886-2-27528585
Southeast Asia
Singapore
Tel: 65-6586-1900
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Central
Novi, MI
Tel: 248-306-9353
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Guadalajara, Jalisco
Tel: 52-33-3123-2141
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
12
Supercapacitors – FA Series
Disclaimer
This product has been made available through a Private Label Agreement and a Development and Cross-Licensing Agreement between KEMET and NEC TOKIN to expand market
and product offerings for both companies and their respective customers. For more information, please visit http://www.kemet.com/nectokin.
All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and
verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.
All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are
not intended to constitute – and KEMET specifically disclaims – any warranty concerning suitability for a specific customer application or use. The Information is intended for use only
by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise
provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained.
Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still
occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective
circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com
S6018_FA • 3/7/2014
13
Similar pages