NTE7167 Integrated Circuit Vertical Deflection Output Circuit Description: The NTE7167 is a vertical deflection output integrated circuit in a 7- Lead SIP type package designed for use in high- resolution television and CRT display systems that use a bus controller system signal processing IC. It can directly drive the deflection yoke (including the required DC component) from the bus controller system signal processing IC’s sawtooth waveform output. Since the NTE7167 has a maximum deflection current of 2.2AP - P, it is optimal for use in large aperture products, and is capable of driving 33 to 37 inch class monitors. Features: D Low Power Dissipation due to the Provision of a Built - In Pump Circuit D Vertical Output Circuit D On - Chip Thermal Protection Circuit D Good Crossover Characteristics D Supports DC Coupling Absolute Maximum Ratings: (TA = +25°C unless otherwise specified) Maximum Supply Voltage, VCC6 max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40V Output Block Supply Voltage, VCC3 max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85V Deflection Output Current, I2max . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 1.5 to +1.5AP - P Allowable Power Dissipation (With an arbitrarily large heatsink), Pdmax . . . . . . . . . . . . . . . . . . 11W Operating Temperature Range, Topr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 20° to +85°C Storage Temperature Range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . - 40° to +150°C Thermal Resistance, Junction - to - Case, RthJC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.0°C/W Recommended Operating Conditions: (TA = +25°C unless otherwise specified) Parameter Recommended Supply Voltage Operating Supply Voltage Range Recommended Deflection Output Current Symbol Test Conditions Min Typ Max Unit VCC6 - 24 - V VCC6 op 10 - 38 V I2P - P - - 2.2 AP - P Electgrical Characteristics: (TA = +25°C, VCC6 = 24V unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Pump Circuit Charge Saturation Voltage VS7 - 1 I7 = 20mA - - 1.8 V Pump Circuit Discharge Saturation Voltage VS6 - 7 I7 = - 1.1A - - 3.2 V Deflection Output Saturation Voltage (Lower) VS2 - 1 I2 = 1.1A - - 1.5 V Deflection Output Saturation Voltage (Upper) VS3 - 2 I2 = - 1.1A - - 3.5 V IDL 35 - 70 mA VMID 11 12 13 V Idling Current Midpoint Voltage Pin Connection Diagram (Front View) 7 Pump - Up Output 6 VCC 5 Inverting Input 4 Non - Inverting Input 3 Output Stage VCC 2 Ver. Output 1 GND .118 (3.0) .708 (18.0) .527 (13.4) 1 .590 .425 (15.0) (10.8) 7 .228 (5.8) .100 (2.54)