ALSC ASM5I23S09AF-1-16-TT 3.3v spreadtrak zero delay buffer Datasheet

ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
3.3V ‘SpreadTrak’ Zero Delay Buffer
General Features
out five low-skew clocks.
15 MHz to 133 MHz operating range, compatible
The -1H version of the ASM5P23SxxA operates at up to
with CPU and PCI bus frequencies.
133 MHz frequency, and has higher drive than the -1
Zero input - output propagation delay.
device. All parts have on-chip PLLs that lock to an input
Multiple low-skew outputs.
clock on the REF pin. The PLL feedback is on-chip and is
Output-output skew less than 250 pS.
obtained from the CLKOUT pad.
Device-device skew less than 700 pS.
One input drives 9 outputs, grouped as 4+4+1
The ASM5P23S09A has two banks of four outputs each,
(ASM5P23S09A).
which can be controlled by the Select inputs as shown in
One input drives 5 outputs (ASM5P23S05A).
the Select Input Decoding Table. If all the output clocks are
Less than 200 pS cycle-to-cycle jitter is compatible
®
not required, Bank B can be three-stated. The select input
with Pentium based systems.
also allows the input clock to be directly applied to the
Test Mode to bypass PLL (ASM5P23S09A only,
outputs for chip and system testing purposes.
refer Select Input Decoding Table).
Available in 16-pin, 150-mil SOIC and 4.4 mm
Multiple ASM5P23S09A and ASM5P23S05A devices can
TSSOP packages for ASM5P23S09A and in
accept the same input clock and distribute it. In this case
8-pin, 150-mil SOIC and 4.4 mm TSSOP
the skew between the outputs of the two devices is
packages for ASM5P23S05A.
guaranteed to be less than 700 pS.
3.3V operation
Advanced 0.35< CMOS technology.
All outputs have less than 200 pS of cycle-to-cycle jitter.
‘SpreadTrak’.
The input and output propagation delay is guaranteed to be
less than 250 pS, and the output to output skew is
Functional Description
guaranteed to be less than 250 pS.
ASM5P23S09A is a versatile, 3.3V zero-delay buffer
designed to distribute high-speed clocks with Spread
Spectrum capability. It is available in a 16-pin package. The
ASM5P23S05A
is
the
eight-pin
version
of
the
ASM5P23S09A. It accepts one reference input and drives
The ASM5P23S09A and the ASM5P23S05A are available
in two different configurations, as shown in the ordering
information table. The ASM5P23SxxA-1 is the base part.
The ASM5P23SxxA-1H is the high drive version of the -1
part and its rise and fall times are much faster than -1 part.
Block Diagram
REF
CLKOUT
PLL
MUX
PLL
REF
CLKA1
CLKA2
CLK1
CLKA3
CLK2
CLK3
CLKOUT
CLKA4
S2
CLK4
Select Input
Decoding
S1
CLKB1
CLKB2
CLKB3
CLKB4
ASM5P23S05A
ASM5P23S09A
Alliance Semiconductor
2575, Augustine Drive • Santa Clara, CA • Tel: 408.855.4900 • Fax: 408.855.4999 • www.alsc.com
Notice: The information in this document is subject to change without notice.
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Select Input Decoding for ASM5P23S09A
CLKOUT
1
Output Source
PLL
S2
S1
Clock A1 - A4
Clock B1 - B4
0
0
Three-state
Three-state
Driven
PLL
N
0
1
Driven
Three-state
Driven
PLL
N
1
0
Driven
Driven
Driven
Reference
Y
1
1
Driven
Driven
Driven
PLL
N
Shut-Down
Note:
1. This output is driven and has an internal feedback for the PLL. The load on this output can be adjusted to change the skew between the reference and the
output.
Zero Delay and Skew Control
SpreadTrak
All outputs should be uniformly loaded to achieve Zero
Many systems being designed now utilize a technology
Delay between input and output. Since the CLKOUT pin is
called Spread Spectrum Frequency Timing Generation.
the internal feedback to the PLL, its relative loading can
ASM5P23S09A and ASM5P23S05A are designed so as
adjust the input-output delay.
not to filter off the Spread Spectrum feature of the
For applications requiring zero input-output delay, all
Reference input, assuming it exists. When a zero delay
outputs, including CLKOUT, must be equally loaded. Even
if CLKOUT is not used, it must have a capacitive load equal
to that on other outputs, for obtaining zero-input-output
delay.
buffer is not designed to pass the Spread Spectrum feature
through, the result is a significant amount of tracking skew
which may cause problems in the systems requiring
synchronization.
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
2 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Pin Configuration
REF
1
16
CLKOUT
CLKA1
CLKA4
2
15
CLKA2
3
14
CLKA3
V
13
V
12
GND
DD
4
GND
5
CLKB1
6
11
CLKB4
CLKB2
7
10
CLKB3
S2
8
9
REF
1
CLK2
2
CLK1
3
GND
4
ASM5P23S09A
ASM5P23S05A
DD
S1
8
CLKOUT
7
CLK4
6
V
5
CLK3
DD
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
3 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Pin Description for ASM5P23S09A
Pin #
Pin Name
1
REF
2
3
2
Description
Input reference frequency, 5V tolerant input
CLKA1
3
Buffered clock output, bank A
CLKA2
3
Buffered clock output, bank A
4
VDD
3.3V supply
5
GND
Ground
6
CLKB1
3
Buffered clock output, bank B
CLKB2
3
Buffered clock output, bank B
7
8
9
S2
4
S1
4
Select input, bit 2
Select input, bit 1
CLKB3
3
Buffered clock output, bank B
11
CLKB4
3
Buffered clock output, bank B
12
GND
13
VDD
10
14
15
16
Ground
3.3V supply
CLKA3
3
CLKA4
3
Buffered clock output, bank A
Buffered clock output, bank A
3
CLKOUT
Buffered output, internal feedback on this pin
Pin Description for ASM5P23S05A
Pin #
1
Pin Name
REF
2
2
CLK2
3
3
CLK1
3
4
GND
5
CLK3
6
VDD
7
8
CLK4
Description
Input reference frequency, 5V-tolerant input
Buffered clock output
Buffered clock output
Ground
3
Buffered clock output
3.3V supply
3
Buffered clock output
3
CLKOUT
Buffered clock output, internal feedback on this pin
Notes:
2. Weak pull-down.
3. Weak pull-down on all outputs.
4. Weak pull-up on these inputs.
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
4 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Absolute Maximum Ratings
Parameter
Min
Max
Unit
Supply Voltage to Ground Potential
-0.5
+7.0
V
DC Input Voltage (Except REF)
-0.5
VDD + 0.5
V
DC Input Voltage (REF)
-0.5
7
V
Storage Temperature
-65
+150
°C
260
°C
Junction Temperature
150
°C
Static Discharge Voltage
2000
V
Max. Soldering Temperature (10 sec)
(per MIL-STD-883, Method 3015)
Note: These are stress ratings only and functional usage is not implied. Exposure to absolute maximum ratings for prolonged periods can affect device
reliability.
Operating Conditions for ASM5P23S05A and ASM5P23S09A - Commercial Temperature Devices
Parameter
Description
Min
Max
Unit
3.0
3.6
V
0
70
°C
VDD
Supply Voltage
TA
Operating Temperature (Ambient Temperature)
CL
Load Capacitance, below 100 MHz
30
pF
CL
Load Capacitance, from 100 MHz to 133 MHz
10
pF
CIN
Input Capacitance
7
pF
Electrical Characteristics for ASM5P23S05A and ASM5P23S09A - Commercial Temperature Devices
Parameter
VIL
Description
Input LOW Voltage
Test Conditions
Min
Typ
5
5
Max
Unit
0.8
V
VIH
Input HIGH Voltage
IIL
Input LOW Current
VIN = 0V
50.0
<A
IIH
Input HIGH Current
VIN = VDD
100.0
<A
0.4
V
VOL
Output LOW Voltage
2.0
6
V
IOL = 8mA (-1)
IOH = 12mA (-1H)
VOH
Output HIGH Voltage
6
IOL = -8mA (-1)
2.4
V
IOH = -12mA (-1H)
IDD
Supply Current
ZO
Output Impedance
34
Unloaded outputs at
mA
66.67 MHz, SEL inputs at VDD
23
K
Notes:
5. REF input has a threshold voltage of VDD/2
6. Parameter is guaranteed by design and characterization. Not 100% tested in production
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
5 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
7
Switching Characteristics for ASM5P23S05A-1 and ASM5P23S09A-1 Commercial Temperature Devices
Parameter
1/t1
Description
Test Conditions
Output Frequency
8
Duty Cycle = (t2 / t1) * 100
t3
t4
Output Rise Time
Output Fall Time
8
8
8
t5
Output-to-output skew
t6
Delay, REF Rising Edge to
CLKOUT Rising Edge
t7
Min
Typ
Max
Unit
MHz
30-pF load
15
100
10-pF load
15
133
Measured at 1.4V, FOUT = 66.67 MHz
40.0
50.0
60.0
%
Measured between 0.8V and 2.0V
2.50
nS
Measured between 2.0V and 0.8V
2.50
nS
All outputs equally loaded
250
pS
Measured at VDD /2
0
±350
pS
Measured at VDD/2 on the CLKOUT pins of
0
700
pS
Measured at 66.67 MHz, loaded outputs
200
pS
Stable power supply, valid clock presented
1.0
mS
8
Device-to-Device Skew
8
the device
tJ
tLOCK
Cycle-to-cycle jitter
PLL Lock Time
8
8
on REF pin
Notes:
7. All parameters specified with loaded outputs.
8. Parameter is guaranteed by design and characterization. Not 100% tested in production
Operating Conditions for ASM5I23S05A and ASM5I23S09A Industrial Temperature Devices
Parameter
Description
Min
Max
Unit
VDD
Supply Voltage
3.0
3.6
V
TA
Operating Temperature (Ambient Temperature)
-40
85
°C
CL
Load Capacitance, below 100 MHz
30
pF
CL
Load Capacitance, from 100 MHz to 133 MHz
15
pF
CIN
Input Capacitance
7
pF
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
6 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Electrical Characteristics for ASM5I23S05A and ASM5I23S09A Industrial Temperature Devices
Parameter
Description
Test Conditions
Min
Typ
Max
Unit
0.8
V
VIL
Input LOW Voltage
VIH
Input HIGH Voltage
IIL
Input LOW Current
VIN = 0V
50.0
<A
IIH
Input HIGH Current
VIN = VDD
100.0
<A
0.4
V
VOL
Output LOW Voltage
VOH
Output HIGH Voltage
2.0
V
IOL = 8mA (-1, -2)
IOH = 12mA (-1H, -5H)
IOL = -8mA (-1)
IOH = -12mA (-1H)
2.4
V
Unloaded outputs 100MHz REF,
Select inputs at VDD or GND
IDD
ZO
50
Supply Current
mA
Unloaded outputs, 66.67MHz REF (-1)
34
Unloaded outputs, 33MHz REF (-1)
19
Output Impedance
23
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
K
7 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Switching Characteristics for ASM5I23S05A-1H and ASM5I23S09A-1H Industrial Temperature Devices7
Parameter
1/t1
Description
Test Conditions
Output Frequency
9
Duty Cycle = (t2 / t1) * 100
9
Duty Cycle = (t2 / t1) * 100
t3
t4
Output Rise Time
Output Fall Time
9
9
9
t5
Output-to-output skew
t6
Delay, REF Rising Edge to
CLKOUT Rising Edge
t7
Min
Typ
Max
Unit
MHz
30 pF load
15
100
10 pF load
15
133
Measured at 1.4 V, FOUT = 66.67 MHz
40.0
50.0
60.0
Measured at 1.4 V, FOUT < 50.0 MHz
45.0
50.0
55.0
%
Measured between 0.8V and 2.0V
1.50
nS
Measured between 2.0V and 0.8V
1.50
nS
All outputs equally loaded
250
pS
Measured at VDD /2
0
± 350
pS
Measured at VDD/2 on the CLKOUT
0
700
pS
9
Device-to-Device Skew
9
pins of the device
t8
Output Slew Rate
9
Measured between 0.8V and 2.0V
1
V/nS
using Test Circuit #2
tJ
Cycle-to-cycle jitter
9
Measured at 66.67 MHz, loaded
200
pS
1.0
mS
outputs
tLOCK
PLL Lock Time
9
Stable power supply, valid clock pre
sented on REF pin
Note:
9. Parameter is guaranteed by design and characterization. Not 100% tested in production
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
8 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Switching Waveforms
Duty Cycle Timing
t1
t2
1.4 V
1.4 V
1.4 V
All Outputs Rise/Fall Time
OUTPUT
2.0 V
0.8 V
2.0 V
0.8 V
3.3 V
0V
t4
t3
Output - Output Skew
1.4 V
O UTPUT
1.4 V
O UTPUT
t5
Input - Output Propagation Delay
VDD /2
INPUT
VDD /2
OUTPUT
t6
Device - Device Skew
CLKOUT, Device 1
VDD /2
VDD /2
CLKOUT, Device 2
t7
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
9 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Test Circuits
Test Circuit #2
Test Circuit #1
V
V
DD
OUTPUTS
0.1 (F
CLK OUT
1k
DD
OUTPUTS
0.1 (F
1k
C
LOAD
V
0.1 (F
V
DD
GND
GND
0.1 (F
10 pF
DD
GND
GND
For parameter 8t
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
10 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Package Information
8-lead (150-mil) SOIC Package
H
E
D
A2
A
A1
D
C
e
L
B
Dimensions
Symbol
Inches
Min
Max
Millimeters
Min
Max
A1
0.004
0.010
0.10
0.25
A
0.053
0.069
1.35
1.75
A2
0.049
0.059
1.25
1.50
B
0.012
0.020
0.31
0.51
C
0.007
0.010
0.18
0.25
D
0.193 BSC
4.90 BSC
E
0.154 BSC
3.91 BSC
e
0.050 BSC
1.27 BSC
H
0.236 BSC
6.00 BSC
L
0.016
0.050
0.41
1.27
R
0°
8°
0°
8°
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
11 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
8-lead Thin Shrunk Small Outline Package (4.40-MM Body)
H
E
D
A2
A
C
e
A1
L
B
Dimensions
Symbol
Inches
Min
Millimeters
Max
A
Min
Max
0.043
1.10
A1
0.002
0.006
0.05
0.15
A2
0.033
0.037
0.85
0.95
B
0.008
0.012
0.19
0.30
c
0.004
0.008
0.09
0.20
D
0.114
0.122
2.90
3.10
E
0.169
0.177
4.30
4.50
e
0.026 BSC
0.65 BSC
H
0.252 BSC
6.40 BSC
L
0.020
0.028
0.50
0.70
R
0°
8°
0°
8°
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
12 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
16-lead (150 Mil) Molded SOIC Package
PIN 1 ID
1
8
H
E
9
16
D
h
Seating Plane
A2
D
A
e
C
0.004
L
A1
B
Dimensions
Symbol
Inches
Millimeters
Min
Max
Min
Max
A
0.053
0.069
1.35
1.75
A1
0.004
0.010
0.10
0.25
A2
0.049
0.059
1.25
1.50
B
0.013
0.022
0.33
0.53
C
0.008
0.012
0.19
0.27
D
0.386
0.394
9.80
10.01
E
0.150
0.157
3.80
4.00
e
0.050 BSC
1.27 BSC
H
0.228
0.244
5.80
6.20
h
0.010
0.016
0.25
0.41
L
0.016
0.035
0.40
0.89
R
0°
8°
0°
8°
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
13 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
16-lead Thin Shrunk Small Outline Package (4.40-MM Body)
1
8
PIN 1 ID
E
16
A
A2
e
B
Seating Plane
C
A1
D
9
H
L
D
Dimensions
Symbol
Inches
Min
Millimeters
Max
A
Min
Max
0.043
1.20
A1
0.002
0.006
0.05
0.15
A2
0.031
0.041
0.80
1.05
B
0.007
0.012
0.19
0.30
C
0.004
0.008
0.09
0.20
D
0.193
0.201
4.90
5.10
E
0.169
0.177
4.30
4.50
e
0.026 BSC
0.65 BSC
H
0.252 BSC
6.40 BSC
L
0.020
0.030
0.50
0.75
R
0°
8°
0°
8°
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
14 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Ordering Codes
Ordering Code
Marking
Package Type
Operating Range
ASM5P23S09A-1-16-ST
5P23S09A-1
16-pin 150-mil SOIC-TUBE
Commercial
ASM5I23S09A-1-16-ST
5I23S09A-1
16-pin 150-mil SOIC-TUBE
Industrial
ASM5P23S09A-1-16-SR
5P23S09A-1
16-pin 150-mil SOIC-TAPE & REEL
Commercial
ASM5I23S09A-1-16-SR
5I23S09A-1
16-pin 150-mil SOIC-TAPE & REEL
Industrial
ASM5P23S09A-1-16-TT
5P23S09A-1
16-pin 4.4-mm TSSOP-TUBE
Commercial
ASM5I23S09A-1-16-TT
5I23S09A-1
16-pin 4.4-mm TSSOP-TUBE
Industrial
ASM5P23S09A-1-16-TR
5P23S09A-1
16-pin 4.4-mm TSSOP-TAPE & REEL
Commercial
ASM5I23S09A-1-16-TR
5I23S09A-1
16-pin 4.4-mm TSSOP-TAPE & REEL
Industrial
ASM5P23S09A-1H-16-ST 5P23S09A-1H
16-pin 150-mil SOIC-TUBE
Commercial
ASM5I23S09A-1H-16-ST
16-pin 150-mil SOIC-TUBE
Industrial
ASM5P23S09A-1H-16-SR 5P23S09A-1H
16-pin 150-mil SOIC-TAPE & REEL
Commercial
ASM5I23S09A-1H-16-SR
5I23S09A-1H
16-pin 150-mil SOIC-TAPE & REEL
Industrial
ASM5P23S09A-1H-16-TT
5P23S09A-1H
16-pin 4.4-mm TSSOP-TUBE
Commercial
ASM5I23S09A-1H-16-TT
5I23S09A-1H
16-pin 4.4-mm TSSOP-TUBE
Industrial
ASM5P23S09A-1H-16-TR 5P23S09A-1H
16-pin 4.4-mm TSSOP-TAPE & REEL
Commercial
ASM5I23S09A-1H-16-TR
5I23S09A-1H
16-pin 4.4-mm TSSOP-TAPE & REEL
Industrial
ASM5P23S05A-1-08-ST
5P23S05A-1
8-pin 150-mil SOIC-TUBE
Commercial
ASM5I23S05A-1-08-ST
5I23S05A-1
8-pin 150-mil SOIC-TUBE
Industrial
ASM5P23S05A-1-08-SR
5P23S05A-1
8-pin 150-mil SOIC-TAPE & REEL
Commercial
ASM5I23S05A-1-08-SR
5I23S05A-1
8-pin 150-mil SOIC-TAPE & REEL
Industrial
ASM5P23S05A-1-08-TT
5P23S05A-1
8-pin 4.4-mm TSSOP-TUBE
Commercial
ASM5I23S05A-1-08-TT
5I23S05A-1
8-pin 4.4-mm TSSOP-TUBE
Industrial
ASM5P23S05A-1-08-TR
5P23S05A-1
8-pin 4.4-mm TSSOP-TAPE & REEL
Commercial
ASM5I23S05A-1-08-TR
5I23S05A-1
8-pin 4.4-mm TSSOP-TAPE & REEL
Industrial
ASM5P23S05A-1H-08-ST 5P23S05A-1H
8-pin 150-mil SOIC-TUBE
Commercial
ASM5I23S05A-1H-08-ST
8-pin 150-mil SOIC-TUBE
Industrial
ASM5P23S05A-1H-08-SR 5P23S05A-1H
8-pin 150-mil SOIC-TAPE & REEL
Commercial
ASM5I23S05A-1H-08-SR
5I23S05A-1H
8-pin 150-mil SOIC-TAPE & REEL
Industrial
ASM5P23S05A-1H-08-TT
5P23S05A-1H
8-pin 4.4-mm TSSOP-TUBE
Commercial
ASM5I23S05A-1H-08-TT
5I23S05A-1H
8-pin 4.4-mm TSSOP-TUBE
Industrial
ASM5P23S05A-1H-08-TR 5P23S05A-1H
8-pin 4.4-mm TSSOP-TAPE & REEL
Commercial
ASM5I23S05A-1H-08-TR
8-pin 4.4-mm TSSOP-TAPE & REEL
Industrial
5I23S09A-1H
5I23S05A-1H
5I23S05A-1H
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
15 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Ordering Codes (Contd..)
Ordering Code
Marking
Package Type
Operating Range
ASM5P23S09AF-1-16-ST
5P23S09AF-1
16-pin 150-mil SOIC-TUBE, Pb free
Commercial
ASM5I23S09AF-1-16-ST
5I23S09AF-1
16-pin 150-mil SOIC-TUBE, Pb free
Industrial
ASM5P23S09AF-1-16-SR
5P23S09AF-1
16-pin 150-mil SOIC-TAPE & REEL, Pb free
Commercial
ASM5I23S09AF-1-16-SR
5I23S09AF-1
16-pin 150-mil SOIC-TAPE & REEL, Pb free
Industrial
ASM5P23S09AF-1-16-TT
5P23S09AF-1
16-pin 4.4-mm TSSOP-TUBE, Pb free
Commercial
ASM5I23S09AF-1-16-TT
5I23S09AF-1
16-pin 4.4-mm TSSOP-TUBE, Pb free
Industrial
ASM5P23S09AF-1-16-TR
5P23S09AF-1
16-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Commercial
ASM5I23S09AF-1-16-TR
5I23S09AF-1
16-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Industrial
ASM5P23S09AF-1H-16-ST 5P23S09AF-1H
16-pin 150-mil SOIC-TUBE, Pb free
Commercial
ASM5I23S09AF-1H-16-ST
16-pin 150-mil SOIC-TUBE, Pb free
Industrial
ASM5P23S09AF-1H-16-SR 5P23S09AF-1H
16-pin 150-mil SOIC-TAPE & REEL, Pb free
Commercial
ASM5I23S09AF-1H-16-SR
16-pin 150-mil SOIC-TAPE & REEL, Pb free
Industrial
ASM5P23S09AF-1H-16-TT 5P23S09AF-1H
16-pin 4.4-mm TSSOP-TUBE, Pb free
Commercial
ASM5I23S09AF-1H-16-TT
16-pin 4.4-mm TSSOP-TUBE, Pb free
Industrial
ASM5P23S09AF-1H-16-TR 5P23S09AF-1H
16-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Commercial
ASM5I23S09AF-1H-16-TR
5I23S09AF-1H
16-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Industrial
ASM5P23S05AF-1-08-ST
5P23S05AF-1
8-pin 150-mil SOIC-TUBE, Pb free
Commercial
ASM5I23S05AF-1-08-ST
5I23S05AF-1
8-pin 150-mil SOIC-TUBE, Pb free
Industrial
ASM5P23S05AF-1-08-SR
5P23S05AF-1
8-pin 150-mil SOIC-TAPE & REEL, Pb free
Commercial
ASM5I23S05AF-1-08-SR
5I23S05AF-1
8-pin 150-mil SOIC-TAPE & REEL, Pb free
Industrial
ASM5P23S05AF-1-08-TT
5P23S05AF-1
8-pin 4.4-mm TSSOP-TUBE, Pb free
Commercial
ASM5I23S05AF-1-08-TT
5I23S05AF-1
8-pin 4.4-mm TSSOP-TUBE, Pb free
Industrial
ASM5P23S05AF-1-08-TR
5P23S05AF-1
8-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Commercial
ASM5I23S05AF-1-08-TR
5I23S05AF-1
8-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Industrial
ASM5P23S05AF-1H-08-ST 5P23S05AF-1H
8-pin 150-mil SOIC-TUBE, Pb free
Commercial
ASM5I23S05AF-1H-08-ST
8-pin 150-mil SOIC-TUBE, Pb free
Industrial
ASM5P23S05AF-1H-08-SR 5P23S05AF-1H
8-pin 150-mil SOIC-TAPE & REEL, Pb free
Commercial
ASM5I23S05AF-1H-08-SR
8-pin 150-mil SOIC-TAPE & REEL, Pb free
Industrial
ASM5P23S05AF-1H-08-TT 5P23S05AF-1H
8-pin 4.4-mm TSSOP-TUBE, Pb free
Commercial
ASM5I23S05AF-1H-08-TT
8-pin 4.4-mm TSSOP-TUBE, Pb free
Industrial
ASM5P23S05AF-1H-08-TR 5P23S05AF-1H
8-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Commercial
ASM5I23S05AF-1H-08-TR
8-pin 4.4-mm TSSOP-TAPE & REEL, Pb free
Industrial
5I23S09AF-1H
5I23S09AF-1H
5I23S09AF-1H
5I23S05AF-1H
5I23S05AF-1H
5I23S05AF-1H
5I23S05AF-1H
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
16 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Device Ordering Information
A S M 5 P 2 3 S 0 5 A
F - 0 8 T R
OR - SOT23/T/R
TT – TSSOP, TUBE
TR - TSSOP, T/R
VT – TVSOP, TUBE
VR – TVSOP, T/R
ST – SOIC, TUBE
SR - SOIC, T/R
QR – QFN, T/R
QT - QFN, TUBE
BT - BGA, TUBE
BR – BGA, T/R
PIN COUNT
LEAD FREE PART
PART NUMBER
X = Automotive
I = Industrial
1 – reserved
2 - Non PLL based
3 – EMI Reduction
4 – DDR support products
5 – STD Zero Delay Buffer
P or n/c = Commercial
6 – power management
7 – power management
8 – power management
9 – Hi performance
0 - reserved
Alliance Semiconductor Mixed Signal Product
Licensed under US patent #5,488,627, #6,646,463 and #5,631,920.
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
17 of 18
ASM5P23S09A
ASM5P23S05A
November 2004
rev 1.3
Alliance Semiconductor Corporation
2575, Augustine Drive,
Santa Clara, CA 95054
Tel# 408-855-4900
Fax: 408-855-4999
www.alsc.com
Copyright © Alliance Semiconductor
All Rights Reserved
Part Number: ASM5P23S09A
ASM5P23S05A
Document Version: 1.3
Note: This product utilizes US Patent # 6,646,463 Impedance Emulator Patent issued to Alliance Semiconductor, dated 11-11-2003
© Copyright 2003 Alliance Semiconductor Corporation. All rights reserved. Our three-point logo, our name and Intelliwatt are
trademarks or registered trademarks of Alliance. All other brand and product names may be the trademarks of their
respective companies. Alliance reserves the right to make changes to this document and its products at any time without
notice. Alliance assumes no responsibility for any errors that may appear in this document. The data contained herein
represents Alliance's best data and/or estimates at the time of issuance. Alliance reserves the right to change or correct this
data at any time, without notice. If the product described herein is under development, significant changes to these
specifications are possible. The information in this product data sheet is intended to be general descriptive information for
potential customers and users, and is not intended to operate as, or provide, any guarantee or warrantee to any user or
customer. Alliance does not assume any responsibility or liability arising out of the application or use of any product
described herein, and disclaims any express or implied warranties related to the sale and/or use of Alliance products
including liability or warranties related to fitness for a particular purpose, merchantability, or infringement of any intellectual
property rights, except as express agreed to in Alliance's Terms and Conditions of Sale (which are available from Alliance).
All sales of Alliance products are made exclusively according to Alliance's Terms and Conditions of Sale. The purchase of
products from Alliance does not convey a license under any patent rights, copyrights; mask works rights, trademarks, or any
other intellectual property rights of Alliance or third parties. Alliance does not authorize its products for use as critical
components in life-supporting systems where a malfunction or failure may reasonably be expected to result in significant
injury to the user, and the inclusion of Alliance products in such life-supporting systems implies that the manufacturer
assumes all risk of such use and agrees to indemnify Alliance against all claims arising from such use.
3.3V ‘SpreadTrak’ Zero Delay Buffer
Notice: The information in this document is subject to change without notice.
18 of 18
Similar pages