Continental Device India Limited An ISO/TS 16949, ISO 9001 and ISO 14001 Certified Company SILICON PLANAR EPITAXIAL TRANSISTORS BC 307, A, B, C BC 308, A, B, C BC 309, A, B, C TO-92 Plastic Package General Purpose Transistors Deisgned For Small Signal Amplification From DC To Low Radio Frequencies ABSOLUTE MAXIMUM RATINGS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL BC307 BC308 BC309 VCEO Collector Emitter Voltage 45 25 25 VCBO 50 30 30 Collector Base Voltage VEBO Emitter Base Voltage 5 5 5 IC Collector Current Continuous 100 PD Power Dissipation@ Ta=25ºC 350 Derate Above 25ºC 2.8 P Power Dissipation@ Tc=25ºC 1 D Derate Above 25ºC 8 Tj, Tstg Operating And Storage Junction -55 to +150 Temperature Range THERMAL RESISTANCE Junction to ambient Junction to case Continental Device India Limited Rth(j-a) Rth(j-c) 357 125 Data Sheet UNITS V V V mA mW mW/°C W mW/°C °C °C/W °C/W Page 1 of 5 SILICON PLANAR EPITAXIAL TRANSISTORS BC 307, A, B, C BC 308, A, B, C BC 309, A, B, C TO-92 Plastic Package ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION MIN BVCEO IC=2mA,IB=0 Collector Emitter Breakdown Voltage BC307 45 BC308, BC309 25 Emitter Base Breakdown Voltage Collector Emitter Leakage Current BC307 BVEBO ICES BC308, BC309 BC307 IE=100uA, IC=0 TYP MAX UNITS V V 5 V VCES =50V, VBE =0 15 nA VCES =30V, VBE =0 15 nA VCES =50V, VBE =0, 4 µA 4 µA o TA =125 C VCES =30V, VBE =0, BC308, BC309 o TA =125 C DC Current Gain A B C BC307, BC308, BC309 A B C A B C Collector Emitter Saturation Voltage Base Emitter Saturation Voltage Base Emitter On Voltage Continental Device India Limited hFE IC=10uA,VCE=5V IC=2mA,VCE=5V 90 150 270 120 120 200 420 170 290 500 0.55 120 180 300 0.10 0.25 0.7 1.0 0.62 IC=2mA,VCE=5V* VCE(sat) IC=10mA,IB=0.5mA IC=100mA,IB=5mA VBE(sat) IC=10mA,IB=0.5mA IC=100mA,IB=5mA VBE(on) IC=2mA,VCE=5V Data Sheet 800 220 460 800 0.3 0.7 V V V V V Page 2 of 5 SILICON PLANAR EPITAXIAL TRANSISTORS BC 307, A, B, C BC 308, A, B, C BC 309, A, B, C TO-92 Plastic Package ELECTRICAL CHARACTERISTICS (Ta=25ºC unless specified otherwise) DESCRIPTION SYMBOL TEST CONDITION MIN DYNAMIC CHARACTERISTICS fT Transition Frequency BC307 BC308 BC309 Collector Base Capacitance BC 309 BC307, BC308 BC309 MAX UNITS IC=10mA, VCE=5V f=50MHz Ccbo VCB=10V, IE=0 NF f=1MHz IC=0.2mA, VCE=5V Noise Figure TYP Rg=2KΩ f=30Hz to 15KHz f =1KHz, B=200Hz 280 320 360 MHz MHz MHz 6 pF 2 4 dB 2 2 10 4 dB dB RS=2KΩ f=30Hz to 15KHz *Pulse Condition: Width < 300µs, Duty Cycle < 2%. Continental Device India Limited Data Sheet Page 3 of 5 BC 307, A, B, C BC 308, A, B, C BC 309, A, B, C TO-92 Plastic Package TO-92 Plastic Package Dimension With 'L' Uncontrolled B TO-92 Transistors on Tape and Ammo Pack Ammo Pack Style A MECHANICAL DATA h P T h (p) A1 LABEL A L H1 D FEE Carrier Strip FLAT SIDE 8.2" W2 H0 L Wo W1 W 1 13" t1 K 2 F1 t F D 3 D A A C 3 2 1 H F F PIN CONFIGURATION 1. EMITTER 2. BASE 3. COLLECTOR 1.7 Do 7" Po 3 2 1 DIM MIN. MAX. A B 4.32 4.45 5.33 5.20 C D 3.18 0.41 4.19 0.55 E F 0.35 0.50 5 DEG G H 1.14 1.14 1.40 1.53 K L 12.70 1.982 — 2.082 All diminsions in mm. Flat Side of Transistor and Adhesive Tape Visible 2000 pcs./Ammo Pack All dimensions in mm unless specified otherwise ITEM SEC AA G F2 P2 E Solderability Ensured Beyond 'L' Adhesive Tape on Top Side SYMBOL BODY WIDTH BODY HEIGHT BODY THICKNESS PITCH OF COMPONENT FEED HOLE PITCH A1 A T P Po FEED HOLE CENTRE TO COMPONENT CENTRE P2 DISTANCE BETWEEN OUTER LEADS COMPONENT ALIGNMENT TAPE WIDTH HOLD-DOWN TAPE WIDTH HOLE POSITION F h W Wo W1 HOLD-DOWN TAPE POSITION LEAD WIRE CLINCH HEIGHT COMPONENT HEIGHT LENGTH OF SNIPPED LEADS FEED HOLE DIAMETER TOTAL TAPE THICKNESS LEAD - TO - LEAD DISTANCEF1, W2 Ho H1 L Do t F2 CLINCH HEIGHT PULL - OUT FORCE H2 (P) SPECIFICATION REMARKS MIN. NOM. MAX. TOL . 4.0 4.8 5.2 4.8 4.2 3.9 12.7 ±1 12.7 ±0.3 CUMULATIVE PITCH ERROR 1.0 mm/20 PITCH 6.35 ±0.4 TO BE MEASURED AT BOTTOM OF CLINCH +0.6 5.08 -0.2 1 0 AT TOP OF BODY 18 ±0.5 6 ±0.2 9 +0.7 -0.5 0.5 ±0.2 16 ±0.5 23.25 11.0 4 ±0.2 1.2 t1 0.3 - 0.6 2.54 +0.4 -0.1 3 6N NOTES 1. MAXIMUM ALIGNMENT DEVIATION BETWEEN LEADS NOT TO BE GREATER THAN 0.2 mm. 2. MAXIMUM NON-CUMULATIVE VARIATION BETWEEN TAPE FEED HOLES SHALL NOT EXCEED 1 mm IN 20 PITCHES. 3. HOLDDOWN TAPE NOT TO EXCEED BEYOND THE EDGE(S) OF CARRIER TAPE AND THERE SHALL BE NO EXPOSURE OF ADHESIVE. 4. NO MORE THAN 3 CONSECUTIVE MISSING COMPONENTS ARE PERMITTED. 5. A TAPE TRAILER, HAVING AT LEAST THREE FEED HOLES ARE REQUIRED AFTER THE LAST COMPONENT. 6. SPLICES SHALL NOT INTERFERE WITH THE SPROCKET FEED HOLES. Packing Detail PACKAGE TO-92 Bulk TO-92 T&A STANDARD PACK Details Net Weight/Qty 1K/polybag 200 gm/1K pcs 2K/ammo box 645 gm/2K pcs Continental Device India Limited INNER CARTON BOX Size Qty 3" x 7.5" x 7.5" 5K 12.5" x 8" x 1.8" 2K Data Sheet OUTER CARTON BOX Size Qty Gr Wt 17" x 15" x 13.5" 80K 23 kgs 17" x 15" x 13.5" 32K 12.5 kgs Page 4 of 5 Notes BC 307, A, B, C BC 308, A, B, C BC 309, A, B, C TO-92 Plastic Package Disclaimer The product information and the selection guides facilitate selection of the CDIL's Discrete Semiconductor Device(s) best suited for application in your product(s) as per your requirement. It is recommended that you completely review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application. The information furnished in the Data Sheet and on the CDIL Web Site/CD is believed to be accurate and reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information. Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL product; neither does it convey any license under its patent rights nor rights of others. These products are not designed for use in life saving/support appliances or systems. CDIL customers selling these products (either as individual Discrete Semiconductor Devices or incorporated in their end products), in any life saving/support appliances or systems or applications do so at their own risk and CDIL will not be responsible for any damages resulting from such sale(s). CDIL strives for continuous improvement and reserves the right to change the specifications of its products without prior notice. CDIL is a registered Trademark of Continental Device India Limited C-120 Naraina Industrial Area, New Delhi 110 028, India. Telephone + 91-11-579 6150 Fax + 91-11-579 9569, 579 5290 e-mail [email protected] www.cdil.com BC307_9_A_B_C Rev160701 Continental Device India Limited Data Sheet Page 5 of 5