MOP06(W) MOP06(W) SERIES DC-DC CONVERTER 2:1 & 4:1 WIDE INPUT RANGE UP TO 6 WATTS FEATURES APPLICATIONS • REINFORCED INSULATION FOR 300VAC WORKING VOLTAGE • CLEARANCE AND CREEPAGE DISTANCE :6.6mm/2MOOP • 3000VAC INPUT TO OUTPUT 2MOOP ISOLATION • BUILT-IN EMI CLASS A FILTER • 2µA PATIENT LEAKAGE CURRENT • SAFETY MEETS ANSI/AAMI ES60601-1, EN60601-1 AND IEC60601-1 • CE MARK MEETS 2006/95/EC, 2011/95/EC AND 2004/108/EC • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU 3000VAC ISOLATION UVP OCP MEDICAL EQUIPMENT TELECOM/DATACOM INDUSTRY CONTROL SYSTEM MEASUREMENT EQUIPMENT SEMICONDUCTOR EQUIPMENT PV POWER SYSTEM IGBT GATE DRIVER LOW STANDBY POWER OVP SCP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25ºC otherwise noted Model Number MOP06-05S3P3A/B MOP06-05S05A/B MOP06-05S12A/B MOP06-05S15A/B MOP06-05S24A/B MOP06-05D05A/B MOP06-05D12A/B MOP06-05D15A/B MOP06-12S3P3A/B MOP06-12S05A/B MOP06-12S12A/B MOP06-12S15A/B MOP06-12S24A/B MOP06-12D05A/B MOP06-12D12A/B MOP06-12D15A/B MOP06-24S3P3A/B MOP06-24S05A/B MOP06-24S12A/B MOP06-24S15A/B MOP06-24S24A/B MOP06-24D05A/B MOP06-24D12A/B MOP06-24D15A/B MOP06-48S3P3A/B MOP06-48S05A/B MOP06-48S12A/B MOP06-48S15A/B MOP06-48S24A/B MOP06-48D05A/B MOP06-48D12A/B MOP06-48D15A/B Page 1 of 4 Input Range Output Voltage Output Current @ Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 4.5 ~9 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 1800 1200 500 400 250 ±600 ±250 ±200 1800 1200 500 400 250 ±600 ±250 ±200 1800 1200 500 400 250 ±600 ±250 ±200 1800 1200 500 400 250 ±600 ±250 ±200 mA 10 10 15 15 20 25 25 25 10 10 10 10 10 10 10 10 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 81.5 86 86 86 87 84 86.5 87.5 83.5 86 89 89 88.5 84 89 88 83 86.0 89 89 88.5 85 88.5 88 82.5 86.5 88 88.5 88 85 88 88 µF 2100 1500 260 210 75 ± 860 ± 150 ± 110 2100 1500 260 210 75 ± 860 ± 150 ± 110 2100 1500 260 210 75 ± 860 ± 150 ± 110 2100 1500 260 210 75 ± 860 ± 150 ± 110 www.pduke.com 2013/7/9 MOP06(W) Model Number Input Range Output Voltage Output Current @ Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 VDC 3.3 5 12 15 24 ±5 ±12 ±15 3.3 5 12 15 24 ±5 ±12 ±15 mA 1800 1200 500 400 250 ±600 ±250 ±200 1800 1200 500 400 250 ±600 ±250 ±200 mA 6 6 6 6 6 6 6 6 4 4 4 4 4 4 4 4 % 83 86.0 89 89 88.5 85 88.5 88 82.5 86.5 88 88.5 88 85 88 88 µF 2100 1500 260 210 75 ± 860 ± 150 ± 110 2100 1500 260 210 75 ± 860 ± 150 ± 110 MOP06-24S3P3WA/B MOP06-24S05WA/B MOP06-24S12WA/B MOP06-24S15WA/B MOP06-24S24WA/B MOP06-24D05WA/B MOP06-24D12WA/B MOP06-24D15WA/B MOP06-48S3P3WA/B MOP06-48S05WA/B MOP06-48S12WA/B MOP06-48S15WA/B MOP06-48S24WA/B MOP06-48D05WA/B MOP06-48D12WA/B MOP06-48D15WA/B PART NUMBER STRUCTURE MOP06 - Series name 48 S 05 W A Input Voltage (VDC) Output Quantity Output Voltage (VDC) Input Range Pin Connection Option 4.5~9 9~18 18~36 36~75 S: Single 05: 12: 24: 48: D: Dual W: 24: 9~36 48: 18~75 3P3: 05: 12: 15: 24: 05: 12: 15: INPUT SPECIFICATIONS Parameter 3.3 5V 12 15 24 ±5 ±12 ±15 2:1 (W) 4:1 Start-up voltage 2:1 (W) 4:1 Shutdown voltage 2:1 (W) 4:1 Input surge voltage Input filter Remote ON/OFF (Only for B-type Pin connection option) Page 2 of 4 A: A type(Standard) B: B type Conditions Operating input voltage range Start up time : 2:1 W: 4:1 Constant resistive load 3 second, max. 2:1 3 second, max. (W) 4:1 Referenced to - INPUT pin 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48 Vin(nom) 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 5Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) DC-DC ON DC-DC OFF Input current of CTRL pin Remote off input current www.pduke.com - P T Remote On/Off Option Trim Option : No On/Off control P: Remote On/Off (Only for B type Pin connection) : No Trim T: Trim (Only for B type Pin connection) Min. Typ. Max. 4.5 9 18 36 9 18 5 12 24 48 24 48 9 18 36 75 36 75 4.5 9 18 36 9 18 4 8 16 33 8 16 30 30 -0.5 Unit VDC VDC VDC VDC VDC VDC ms 16 25 VDC 50 100 50 VDC 100 Pi type OPEN or 0 ~ 1.2VDC 2.2 ~ 12VDC 1 mA 2.5 mA 2013/7/9 MOP06(W) OUTPUT SPECIFICATIONS Parameter Voltage accuracy Line regulation Load regulation Cross regulation Voltage adjustability Conditions Low Line to High Line at Full Load No Load to Full Load Asymmetrical load 25%/100% FL Single output (Only for B-type Pin connection option) Ripple and noise Dual output Measured by 20MHz bandwidth With a 10µF/25V X7R MLCC With a 4.7µF/50V X7R MLCC Temperature coefficient Transient response recovery time Over voltage protection Single Dual Single Dual Dual 3.3Vout, 5Vout, 12Vout 15Vout, 24Vout ±5Vout, ±12Vout, ±15Vout 3.3Vout, 5Vout 12Vout, 15Vout 24Vout 30 40 50 3.3Vout 5Vout 12Vout 15Vout 24Vout Operating ambient temperature Storage temperature range Thermal impedance Thermal shock Vibration Relative humidity EMC SPECIFICATIONS Parameter EMI (1) ESD Radiated immunity Fast transient (2) Surge (2) Conducted immunity % % % % % % 5.4 7.0 19.6 22.0 32.5 %/ºC µs VDC 150 % Continuous, automatics recovery Conditions Min. Input to Output 3000 240VAC,60Hz 225 6.6 MIL-HDBK-217F Ta=25ºC, Full load (G/B, controlled environment) ENVIRONMENTAL SPECIFICATIONS Parameter +0.02 3.7 5.6 13.5 18.3 29.1 Case material Base material Potting material Dimensions Weight MTBF Unit mVp-p 250 % of Iout rated; Hiccup mode 1 minute Max. +1.0 +0.2 +0.5 +0.2 +1.0 +5.0 +10 +20 +10 -0.02 GENERAL SPECIFICATIONS Parameter Isolation voltage Isolation capacitance Leakage current Switching frequency Clearance/Creepage Design meet safety standard Typ. -1.0 -0.2 -0.5 -0.2 -1.0 -5.0 -10 -10 -10 25% load step change Continuous clamp Over load protection Short circuit protection Min. Conditions Without derating With derating Min. , Natural convection (20LFM) Typ. Max. VAC pF µA 250 kHz mm ANSI/AAMI ES60601-1 IEC60601-1, EN60601-1 Non-conductive black plastic Non-conductive black plastic Silicon (UL94-V0) 1.25 X 0.80 X 0.40 Inch (31.8×20.3×10.2 mm) 14g (0.48oz) 1.115 x 106 hrs 12 17 2 275 Typ. Max. -40 +88 -55 Unit +88 +105 +125 ºC ºC ºC ºC/W MIL-STD-810F MIL-STD-810F 5% to 95% RH 18 Conditions Unit Level EN55011,EN55022 and FCC Part 18 Air ± 8kV EN61000-4-2 Contact ± 6kV EN61000-4-3 10 V/m EN61000-4-4 ± 2kV EN61000-4-5 ± 2kV EN61000-4-6 10 Vr.m.s Class A ,Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: The MOP06 (W) series can meet EMI Class A with no external filter. And Class B only with external components. For more detail information, please contact with P-DUKE. 2. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The MOP06-05S recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 1000µF/25V). And a reverse diode (Vishay V10P45) to connect in parallel. The MOP06-12&24S recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 470µF/50V). The MOP06-48S recommended an aluminum electrolytic capacitor (Nippon Chemi-con KY series, 330µF/100V). CAUTION: This power module is not internally fused. An input line fuse must always be used. 1. Page 3 of 4 www.pduke.com 2013/7/9 MOP06(W) CHARACTERISTIC CURVE MOP06-48S05WA Derating Curve MOP06-48S05WA Efficiency VS Input Voltage MOP06-48S05WA Efficiency VS Output Load MECHANICAL DRAWING A type Pin connection (Standard) DIP PIN CONNECTION PIN SINGLE DUAL 1 + INPUT + INPUT 11 NO PIN COMMON 12 13 -OUTPUT +OUTPUT NO PIN -OUTPUT 15 NO PIN +OUTPUT 23 - INPUT - INPUT 24 - INPUT - INPUT 1. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) B type Pin connection DIP PIN CONNECTION PIN SINGLE DUAL 1 2 CTRL (Option) - INPUT CTRL (Option) - INPUT 10 11 TRIM (Option) NO PIN / NC (＊＊) TRIM (Option) -OUTPUT 14 +OUTPUT +OUTPUT 16 -OUTPUT COMMON 22 +INPUT +INPUT 23 +INPUT +INPUT ＊＊： 1. The Pin 11 is ”NO PIN” when single output with Trim option (Suffix: -T). The Pin 11 is ”NC” when single output without TRIM pin. All dimensions in Inch (mm) Tolerance: X.XX±0.02 (X.X±0.5) X.XXX±0.01 (X.XX±0.25) Page 4 of 4 www.pduke.com 2. Pin pitch tolerance ±0.01 (0.25) 3. Pin dimension tolerance ±0.004 (0.1) 2013/7/9