200KP295CVCL and 200KP295CA AIRCRAFT AC POWER BUS PROTECTION SCOTTSDALE DIVISION APPEARANCE Microsemi’s 200 kW bidirectional Transient Voltage Suppressor (TVS) protects 120 volt ac airborne electronic equipment from harsh lightning environments per RTCA/DO-160D Section 22 and is compatible with Section 16 for 180 volt ac 100 ms highline surges. Microsemi also offers a broad spectrum of other TVS products to meet your needs. IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com FEATURES • • • • • • • APPLICATIONS / BENEFITS • Symmetrical bidirectional TVS construction Available as either low clamp with “CVCL” suffix or normal clamping features with “CA” suffix. Suppresses transients up to 200 kW @ 10/40 us Fast response with less than 5 ns turn-on time. Optional 100% screening for avionics grade is available by adding MA prefix to part number for added 100% temperature cycle -55oC to +125oC (10X), surge (3X) in each direction, 24 hours HTRB in each direction, and post test (VZ and IR) Options for screening in accordance with MILPRF-19500 for JAN JANTX, JANTXV, and JANS are also available by adding MQ, MX, MV, or MSP prefixes respectively to part numbers Moisture classification is Level 1 with no dry pack required per IPC/JEDEC J-STD-020B • • • • • MAXIMUM RATINGS • • • • • • Pin injection protection per RTCA/DO-160D up to Level 4 for Waveform 4 (6.4/69 µs) and Level 3 for Waveform 5A (40/120 μs) Compatible with “abnormal surge and variation from a controlled steady-state level” as described in 16.5.3.3 of RTCA/DO-160D. The 200KP295CVCL is designed for low clamping protection of 400V transistors, MOSFETs and IGBTs in off-line switching power supplies. The 200KP295CA normal clamp device is for use in less sensitive applications including RFI/EMI filters and general across-the-line protection. Secondary lightning protection per IEC61000-4-5 with 12 Ohms source impedance for Class 1,2, 3 and 4 Secondary lightning protection per IEC61000-4-5 with 2 Ohms source impedance for Class 2 and 3 WWW . Microsemi .C OM DESCRIPTION MECHANICAL & PACKAGING • o Steady-state power dissipation: 7 W @ TA = 25 C Peak Pulse Power at 25oC: 200 kW at 10/40 µs (linear derate to zero @ 150oC) Repetition rate: 0.01% max. Operating & storage temperatures: -55oC to +150oC Temperature coefficient of voltage: +0.100%/oC max o Solder Temperatures: 260 C for 10 s maximum • • • • • CASE: Inner Shell – Epoxy Encapsulated. Exterior Shell – Diallyl Phthallate, glass filled Meets UL 94V-0 flammability requirements FINISH: Tin-Lead plated readily solderable per MIL-STD-750, method 2026 Polarity: No band required for bidirectional MARKING: Manufacturers logo and part number Add prefix MA, MQ, MX, etc., for screened parts Package dimensions: See last page ELECTRICAL PARAMETERS @ 25oC Devices are Bi-directional 200KP295CVCL 200KP295CA Copyright © 2004 8-08-2004 REV B I(BR) mA Peak Pulse Current IPP @ 10/40 μs Amps 5 5 410 460 300 300 Maximum Standby Current ID @ VWM μA Minimum Breakdown Voltage VBR @ I(BR) Volts Breakdown Current 295 295 5 5 300 300 Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 1 200KP295CVCL and 200KP295CA MICROSEMI PART NUMBER Maximum Clamping Voltage VC @ IPP Volts Working Standoff Voltage VWM V max 200KP295CVCL and 200KP295CA AIRCRAFT AC POWER BUS PROTECTION SCOTTSDALE DIVISION Peak Pulse Power (PPP) or continuous o Power in % of 25 C rating PPP Peak Pulse Power vs. Pulse Time – kW Non-Repetitive Pulse NOTE: This PPP vs. Time graph allows the designer to use these parts over a broad power spectrum using the guidelines illustrated in App Note 104 on Microsemi’s website. Aircraft transients are described with exponential decaying waveforms. For suppression of square waveforms, derate power and current to 66% of that for exponential decay. tp – Pulse Time – sec. TL Lead Temperature oC FIGURE 1 Peak Pulse Power vs. Pulse Time To 50% of Exponentially Decaying Pulse FIGURE 2 DERATING CURVE Correct FIGURE 3 INSTALLATION FIGURE 4 Copyright © 2004 8-08-2004 REV B Wrong FIGURE 5 200KP295CVCL and 200KP295CA TVS devices used across power lines are subject to relatively high magnitude surge currents and are more prone to adverse parasitic inductance effects in the mounting leads. Minimizing the shunt path of the lead inductance and their V= -Ldi/dt effects will optimize the TVS effectiveness. Examples of optimum installation and poor installation are illustrated in figures 3 through figure 6. Figure 3 illustrates minimal parasitic inductance with attachment at end of device. Inductive voltage drop is across input leads. Virtually no “overshoot” voltage results as illustrated with figure 4. The loss of effectiveness in protection caused by excessive parasitic inductance is illustrated in figures 5 and 6. Also see MicroNote 111 for further information on “Parasitic Lead Inductance in TVS”. WWW . Microsemi .C OM GRAPHS FIGURE 6 Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 2 200KP295CVCL and 200KP295CA AIRCRAFT AC POWER BUS PROTECTION SCOTTSDALE DIVISION WWW . Microsemi .C OM t t – time Note: frequency is 1MHz t – time FIGURE 7 – Waveform 3 t - Time FIGURE 8 – Waveform 4 FIGURE 9 – Waveform 5a NOTE: The 1MHz damped oscillatory waveform (3) has an effective pulse width of 4 μs. Equivalent peak pulse power for the 200KP295CVCL and 200KP295CA at each of the pulse widths represented in RTCA/DO-160D for wave forms 3, 4 and 5a (above) have been determined referencing Figure 1 herein as well as Application Notes 104 and 120 (found on Microsemi’s website) and are listed below. WAVEFORM NUMBER 3 4 5a PULSE WIDTH PEAK POWER μs 4 6.4/69 40/120 kW 500 150 120 Note: High current fast rise-time transients of 250 ns or less can more than triple the VC from parasitic inductance effects (V= -Ldi/dt) compared to the clamping voltage shown in the initial Electrical Characteristics on page 1 as also described in Figures 5 and 6 herein. DIMENSIONS 200KP295CVCL and 200KP295CA Copyright © 2004 8-08-2004 REV B Microsemi Scottsdale Division 8700 E. Thomas Rd. PO Box 1390, Scottsdale, AZ 85252 USA, (480) 941-6300, Fax: (480) 947-1503 Page 3