SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER CURRENT Plastic package has UL Flammability Glassification 94V-0 Glass passivated chip junctions High case dielectric strength of 1500 VRMS High surge current capability High temperature soldering guaranteed 260℃/10 seconds, 0.375”(9.5mm) lead length 29.7-30.3 4.4-4.8 O 3.4-3.8 - 3 .4 O MECHANICAL DATA • • • 2.5±0.2 2.0-2.4 Case: molded plastic body Terminal: Plated leads solderable per MIL-STD-750 Method 2026 Mounting position: Any (Note 3) Mounting Torque: 6 in – 1bs max. Weight: 0.26 ounce, 7.4 gram 2.7-3.1 3.8-4.2 17.0-18.0 • • 10.8-11.2 .1 φ3 19.7-20.3 3.0×45 5.0 • • • • 8.0 Amperes GBJ FEATURES • 50 to 1000 Volts VOLTAGE RANGE GBJ8005 THRU GBJ810 0.6-0.8 0.9-1.1 9.8-10.2 7.3-7.7 7.3-7.7 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS • • • Ratings at 25℃ ambient temperature unless otherwise specified Single Phase, half wave, 60Hz, resistive or inductive load For capacitive load derate current by 20% GBJ SYMBOLS GBJ Maximum Reverse Peak Repetitive Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current, At TC=100℃ (Note 1) Peak Forward Surge Current 8.3ms single half sine wave superimposed on rated load (JEDEC Method) Rating for Fusing (t＜8.3ms) Maximum Instantaneous Forward Voltage drop Per bridge element 4.0A TA=25℃ Maximum DC Reverse Current at rated DC blocking voltage per element TA=125℃ Typical Junction Capacitance, per let (Note 2) Typical Thermal Resistance (Note 4) Operating Junction Temperature Range Storage Temperature Range VRRM VRMS VDC GBJ GBJ GBJ GBJ GBJ 8005 801 802 804 806 808 810 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 100 UNIT Volts Volts Volts I(AV) 8.0 Amps IFSM 170 Amps I2 t 166 A2s VF 1.0 Volts IR 5.0 500 μA CJ RJA TJ TSTG 211.0 94.0 3.5 (-55 to +150) (-55 to +150) Notes: 1. Unit case mounted on 3.2×3.2×0.12” thick (8.2×8.2×0.3cm) A1. Plate heatdink 2. Measured at 1.0MHz and applied reverse voltage of 4.0 Volts 3. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat Transfer with #6 screws 4.Unit mounted in free air, no heat sink on P.C.B. 0.5×0.5”(12×12mm) copper pads 0.375” (9.5mm) lead length E-mail: [email protected] Web Site: www.cnmic.com pF ℃/W ℃ ℃ SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIER 50 to 1000Volts VOLTAGE RANGE GBJ8005 THRU GBJ810 CURRENT 8.0 Amperes RATINGS AND CHARACTERISTIC CURVES GBJ8005 THRU GBJ810 FIG. 2- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 250 10 60 Hz Resistive or Inductive Load PEAK FORWARD SURGE, CURRENT,(A) AVERAGE FORWARD OUTPUT CURRENT (A) FIG. 1- DERATING CURVE OUTPUT RECTIFIED CURRENT 8.0 Heat-Sink Mounting,on 3.2×3.2×0.12"Thk (8.2×8.2×0.3cm)AL.Plate 6.0 4.0 2.0 TJ =150℃ 8.3ms Single Half Sine-Wave (JEDEC Method) 200 150 100 50 0 0 0 20 50 80 120 100 150 1 FIG. 4- TYPICAL REVERSE CHARACTERISTICS PER LEG FIG. 3- TYPICAL FORWORD CHARACTERISTICS PER LGE 500 INSTANTANEOUS REVERSE CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) 100 10 1 0.1 TJ=25℃ Pulse width=300μS 1% Duty Cycle 0.01 0.4 0.6 0.8 1.0 1.2 1.4 1 0.1 TRANSIENT THERMAL IMPEDANCE (℃/W) JUNCTION CAPACITANCE, (pF) 50-400V 600-1000V 10 REVRESE VOLTAGE,(V) E-mail: [email protected] 0 20 60 40 80 100 100 100 10 TJ =25℃ FIG. 6- TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG TJ=25℃ f=1.0MHz Vsig=50mVp-p 1 50-400V 600-1000V PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG. 5- TYPICAL JUNCTION CAPACITANCE PER LEG 0.1 TJ =125℃ 10 0.01 1.6 TJ =150℃ 100 INSTANTANEOUS FORWARD VOLTAGE,(V) 1000 100 10 NUMBER OF CYCLES AT 60 Hz CASE TEMPERATURE, ℃ 100 10 1 0.1 0.01 0.1 1 10 T, HEATING TIME (SEC.) Web Site: www.cnmic.com 100