ETC2 EIX501NPCSS-5 Proximity sensors inductive stainless steel housing Datasheet

Proximity Sensors Inductive
Stainless Steel Housing
Types EI, Ø 4, 5 x 5 mm
• Miniature stainless steel housing Ø 4,
aluminium 5 x 5 mm
• Sensing distance: 1 mm
• Power supply: 10 to 30 VDC
• Output: Transistor NPN/PNP, make or break switching
• Protection: Short-circuit, reverse polarity and overload
• LED-indication for output ON
• 2 m PUR cable or M8 plug
Product Description
Miniature inductive proximity
sensor available as Ø 4 and
5 x 5 mm types. Output configuration for NPN/PNP with
both NO and NC types as
standard. Housing materials
Ordering Key
are stainless steel for Ø 4 and
aluminium for the 5 x 5 mm
type. Cabled models utilise 2
meters of PUR cable and
plug versions features a
bright ring LED.
EI 0401 PPO SS-5
Type
Housing diameter (mm)
Rated operating dist. (mm)
Output type
Housing material
Housing type
Connection type
Type Selection
Housing
diameter
Rated
operating
dist. (Sn)
Connection
type
Ordering no.
Transistor NPN
Make switching
Ordering no.
Transistor NPN
Break switching
Ordering no.
Transistor PNP
Make switching
Ø 4 mm
Ø 4 mm
0.8 mm 1)
0.8 mm 1)
Cable
Plug
EI 0401 NPOSS
EI 0401 NPOSS-5
EI 0401 NPCSS
EI 0401 NPCSS-5
EI 0401 PPOSS
EI 0401 PPCSS
EI 0401 PPOSS-5 EI 0401 PPCSS-5
5 x 5 mm
5 x 5 mm
0.8 mm 1)
0.8 mm 1)
Cable
Plug
EI X501 NPOSS
EI X501 NPCSS
EI X501 NPOSS-5 EI X501 NPCSS-5
EI X501 PPOSS
EI X501 PPCSS
EI X501 PPOSS-5 EI X501 PPCSS-5
1)
Ordering no.
Transistor PNP
Break switching
For flush mounting in metal
Specifications
Rated operational volt. (UB)
Ripple
Rated operational current (Ie)
Continuous
No-load supply current (Io)
10 to 30 VDC (ripple included)
≤ 10%
≤ 150 mA @ + 25°C (+75°F)
≤ 2.1 mA
OFF: 1.5 mA
ON: 10 mA
Voltage drop (Ud)
<1V
Protection
Reverse polarity,
short-circuit, overload
Transient voltage
≤ 1 kV/0.5 J (prepared)
Power ON delay
Ca. 500 µs
Frequency of operating cycles (f) 1000 Hz
Indication for output ON
LED, yellow
Assured operating dist. (Sa)
0 to 0.52 mm
Repeat accuracy (R)
± 0.01 mm
Hysteresis (H)
(Differential travel)
3 to 15% of sensing distance
0.9 x Sn ≤ Sr ≤ 1.1 x Sn
Effective operating dist. (Sr)
Specifications are subject to change without notice (20.08.01)
Usable operating dist. (Su)
Ambient temperature
Operating
Storage
Degree of protection
Connection
Cable
Plug
Housing material
Body
Ø4
5 x 5 mm
Cap
Weight
Tightening torque
CE-marking
0.85 x Sr ≤ Su ≤ 1.15 x Sr
-25° to +70°C (-13° to +158°F)
-30° to +80°C (-22° to +176°F)
Plug versions: IP 65
Cable versions: IP 67
(Nema 1, 3, 4, 6, 13)
2 m, 3 x 0.14 mm2
grey PUR, oil proof
M8, CONH5A-xxx Serie
Stainless steel (1.4301)
Aluminium
Plastic
Cable versions: 25 g
Plug versions: 4 g
1 Nm
Yes
1
EI, Ø 4, 5 x 5 mm
Dimensions
27
2000
41
20
Ø3
15.4
A
21
A
1(+)
Ø6.9
M8 x 1
Ø4
Ø4
3(-)
LED
4(OUT)
LED
EI 0401 xPxSS
EI 0401 xPxSS-5
46
21
Ø6.9
5x5
5x5
2.8
SENSING FACE
2.8
SENSING FACE
2 x M1.6
2 x M1.6
LED
A
3(-)
1(+)
1.5
A
2.6
M8 x 1
25
2000
Ø3
25
5.5
5.5
14
EI X501 xPxSS
14
4(OUT)
LED
EI X501 xPxSS-5
Wiring Diagrams
1 BN
+
+
1 BN
1 BN
+
1 BN
+
4 BK
2 WH
2 WH
4 BK
3 BU
3 BU
-
NPN - Make switching
-
NPN - Break switching
3 BU
3 BU
PNP - Make switching
PNP - Break switching
Installation Hints
To avoid interference from inductive voltage/
current peaks, separate the prox. switch power cables from any other power cables, e.g.
motor, contactor or solenoid cables
Relief of cable strain
Protection of the sensing face
Switch mounted on mobile carrier
A proximity switch should not serve as
mechanical stop
Any repetitive flexing of the
cable should be avoided
Incorrect
Correct
The cable should not be pulled
Power Supplies
Power supplies VDC:
Power supplies with amplifier relays:
2
> SS 130/140.
> SV 190.
Specifications are subject to change without notice (20.08.01)
Similar pages