PM/P/P Cores Halves/EP/TT/PR Cores Series/Type: P 18 x 11 The following products presented in this data sheet are being withdrawn. Ordering Code Substitute Product B65651D0000R026 B65652A50000000 B65659F0001X101 B65651D0000R048 B65659F0001X023 Date of Withdrawal 2002-08-02 2004-10-18 2004-01-23 Deadline Last Orders 2002-12-31 2005-03-31 Last Shipments 2003-03-31 2005-09-30 For further information please contact your nearest EPCOS sales office, which will also support you in selecting a suitable substitute. The addresses of our worldwide sales network are presented at www.epcos.com/sales. P 18 × 11 Core B65651 ■ In accordance with IEC 60133 ■ Pot cores are supplied in sets Magnetic characteristics (per set) with without center hole center hole Σl/A le Ae A min Ve 0,6 25,9 43 — 1 120 mm–1 mm mm2 mm2 mm3 0,57 26,6 46,7 33,9 1 240 Approx. weight (per set) m 6,0 6,6 g Gapped Material A L value nH µe s approx. mm Ordering code 1) -D with center hole -T w. threaded sleeve 40 ± 3 % 1,60 19 B65651-+40-A1 M33 100 ± 3 % 0,60 48 B65651-+100-A33 N48 160 ± 2 % 250 ± 3 % 315 ± 3 % 400 ± 3 % 500 ± 3 % 630 ± 5 % 0,32 0,20 0,15 0,10 0,07 0,05 77 120 151 192 240 302 B65651-+160-G48 B65651-+250-A48 B65651-+315-A48 B65651-+400-A48 B65651-+500-A48 B65651-D630-J48 K1 Ungapped Material A L value µe nH AL1min P V nH W/set Ordering code -D with center hole -W w/o center hole N26 2900 + 30/– 20 % 1380 N30 5900 + 30/– 20 % 2680 B65651-W-R30 T38 12600 + 40/– 30 % 5710 B65651-W-Y38 N87 3600 + 30/– 20 % 1630 2000 B65651-D-R26 < 0,46 B65651-W-R87 (200 mT, 100 kHz, 100 °C) 1) Replace the + by the code letter ”D“ or ”T“ for the required version. 334 08/01 P 18 × 11 Accessories B65652 Coil former Standard: Material: Winding: to IEC 60133 and DIN 41 294 GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C), color code black see “Processing Notes”, page 155 Insulating washer 1 between core and coil former ■ For tolerance compensation and for insulation ■ Polycarbonate spring washer (UL 94 V-0, insulation class to IEC 60085: E 120 °C), 0,04 mm thick Insulating washer 2 between core and terminal carrier ■ For increased dielectric strength ■ Made of polycarbonate (UL 94 V-0, insulation class to IEC 60085: E 120 °C), 0,08 mm thick Coil former Bestellnummer A R value µΩ Sections AN mm2 lN mm 1 16 35,6 87 B65652-B-T1 2 13 35,6 94 B65652-B-T2 Insulating washer 1 (reel packing, PU = 1 reel) B65652-A5000 Insulating washer 2 (bulk) B65652-A5002 Coil former 0,4 ø7,7+0,1 0,5 7_ 0,1 ø8,7 _ 0,1 ø8,7 _ 0,1 2+0,6 14,8 _ 0,2 ø7,7+0,1 AN 0,5 7_ 0,1 FPK0274-7 Insulating washer 1 Insulating washer 2 335 08/01 P 18 × 11 Accessories B65655 Mounting assembly for printed circuit boards ■ The set comprises a terminal carrier and a yoke ■ For snap-in connection Terminal carrier Material: GFR polyterephthalate (UL 94 V-0, insulation class to IEC 60085: F max. operating temperature 155 °C), color code gray Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 °C, 2 s Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 °C, 3,5 s Yoke Spring yoke, made of tinned nickel silver (0,3 mm), with ground terminal Complete mounting assembly (4 solder terminals) Ordering code: B65655-B9 Complete mounting assembly (8 solder terminals) Ordering code: B65655-B10 4 solder terminals 8 solder terminals Ground Erdungspunkt Ground 8 19,9 max. 1 8 5 1 5 4 4 19,9 max. Erdungspunkt *) 20 max. *) 20 max. a b 13,5 max. 13,5 max. a Hole arrangement View in mounting direction c Hole arrangement View in mounting direction 20,7 max. *) a) b) c) Ground Erdungspunkt ø1,3+0,1 ø1,3+0,1 3,5 3,5 Ground Erdungspunkt 2,54 FPK0295-U 20,7 max. 2,54 This recess must be on the side of the grounding pin to ensure that the yoke locks in position. Yoke Terminal carrier with 4 solder terminals Terminal carrier with 8 solder terminals 336 08/01 FPK0296-3 P 18 × 11 B63399 Accessories B65659 Adjusting screw ■ Tube core with thread and core brake made of GFR polyterephthalate Plastic adjusting screwdriver (not shown) Plastic handle for adjusting screwdriver (not shown) Core P 18 × 11 Material Adjusting screw Tube core AL value Fig. ∅ × length nH mm Min. adjusting range Material Color code Ordering code % 40 a 2,62 × 3,6 Si 1 white 13 B65659-F1-X101 M 33 100 a 2,62 × 3,6 Si 1 white 10 B65659-F1-X101 N 48 160 a 2,62 × 3,6 Si 1 white 7 250 a 2,62 × 3,6 K1 green 10 B65659-F1-X1 315 400 b 2,75 × 4,4 N 22 black 16 12 B65659-F3-X23 400 500 c 2,82 × 4,4 N 22 yellow 16 13 B65659-F4-X23 K1 B65659-F1-X101 Adjusting screwdriver B63399-B4 Handle B63399-B5 Adjusting screw a b c 337 08/01 Herausgegeben von EPCOS AG Marketing Kommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND EPCOS AG 2000. Alle Rechte vorbehalten. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet. Mit den Angaben in dieser Broschüre werden die Bauelemente spezifiziert, keine Eigenschaften zugesichert. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschüre ersetzt die vorige Ausgabe. Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen. Published by EPCOS AG Marketing Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY EPCOS AG 2000. All Rights Reserved. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. The information contained in this brochure describes the type of component and shall not be considered as guaranteed characteristics. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. 1