Contactless Pushbuttons Series FP01 Distinctive Characteristics Brilliant illumination for highly visible status indication with LEDs and caps in red, green, or amber; subdued illumination for low light requirements with white cap over red, green, or amber LEDs. Photo interrupter, rather than contacts, ensures high reliability and long life of 3 million operations minimum. Rugged construction and smooth actuation allow repeated, rapid actuation force anywhere on cap surface. Snap-in mounting for easy installation. Connector socket with 6 pins for simple connection. Well suited for gaming and vending machines, as well as equipment exposed to corrosive gases used in environments such as chemical or steel manufacturing plants. Actual Size FP01-15 NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 TYPICAL SWITCH ORDERING EXAMPLE FP01 1 5 C PHOTO TRANSISTOR 1 5 C Unshaded (Shaded) C1 A C1 Round HOUSING Black (Momentary Operating Function) F F RECEPTACLE SHAPE Single PHOTO INTERRUPTER A LEDS 6-pin Socket C Red See Plug Options. D Amber F Green ACTUATOR COLORS B White C Red D Amber F Green PLUG OPTIONS C2 Assembled Connector Plug with Wire Leads C3 Unassembled Connector Plug and Pins No Code No Connector Plug Contact factory for custom options. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE FP0115CAC1FF Green Actuator with Green LED Single Photo Transistor with Normally Unshaded Photo Interrupter Round, Black Housing No Connector Plug NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Contactless Pushbuttons Series FP01 ACTUATOR & INTERRUPTER Actuator Position Normal Model FP0115 Down 1 Single Photo Transistor Photo Interrupter Unshaded 5 Schematics Shaded Normally Unshaded with Momentary Shaded status LED connector pins are 5 & 6; interrupter connector pins are 3-4 & 1-2. When shaded, the photo transistor momentarily activates electrical function which signals the external device to change its state. 6 5 4 3 2 1 HOUSING SHAPE & COLOR C A Round Shape Black Housing INTERNAL RECEPTACLE C1 Receptacle Internal male connector socket 6 5 4 3 2 1 SWITCH SPECIFICATIONS Status of Photo Interrupter: Collector Current IC: Status of Photo Transistor: Output Condition of Photo Transistor: Actuator Up Actuator Down Unshaded Shaded 0.8mA minimum 10µA maximum On Off IF = 20mA & VCE = 5V MECHANICAL SPECIFICATIONS Total Travel: Operating Force: Mechanical Life: Operating Temperature Range: .079” (2.0mm) 0.75 N (.169 lbf) 3,000,000 operations minimum –25°C through +50°C (–13°F through +122°F) MATERIALS Actuator: Polyacetal Housing: Polyamide NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series FP01 Contactless Pushbuttons PHOTO INTERRUPTER SPECIFICATIONS Electrical & Optical Characteristics (Temperature @ 25°C) Typical Maximum Condition 1.3V 1.6V IF = 50mA Reverse Current IR: 10µA FR = 5V Collector-Emitter Saturation Voltage VCE sat: 0.4V IF = 20mA & IC = 0.1mA Input Forward Voltage VF: Transmission Absolute Maximum Ratings Input LED Output Photo Transistor Forward Current IF: Reverse Voltage VR: Power Dissipation PD: 50mA Collector-Emitter Voltage VCEO: 30V 5V Emitter-Collector Voltage VECO: 4.5V Collector Current IC: 80mW 30mA Collector Dissipation PC: 80mW Circuit Design Considerations VCC = 5V Output of the infrared LED in the photo interrupter decreases approximately 50% after 100,000 hours. 180Ω RL VOUT Threshold Voltage VHI : 3.8V VLO : 1.0V Recommended load resistance (RL) is 40k ~ 120kΩ for the illustrated circuit. GND ACTUATOR COLORS B C White Red D F Amber Green LED COLORS & SPECIFICATIONS LEDs are an integral part of the switch and not available separately. The electrical specifications shown are determined at a basic temperature of 25°C. If the source voltage exceeds the rated voltage, a ballast resistor is required. R + IF Anode C D F Color Red Amber Green Forward Peak Current IFM 30mA 25mA 25mA Continuous Forward Current IF 20mA 20mA 20mA Forward Voltage VF 1.85V 2.0V 2.25V Reverse Peak Voltage VRM 5V 5V 5V Current Reduction Rate Above 25°C ∆IF 0.38mA /°C 0.28mA /°C 0.40mA /°C Single Element LED VF E Cathode – R = Where: R = E = VF = IF = E – VF IF Resistor Value (Ohms) Source Voltage (V) Forward Voltage (V) Forward Current (A) Ambient Temperature Range –25° ~ +50°C NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series FP01 Contactless Pushbuttons EXTERNAL PLUG OPTIONS C2 AT021 Assembled Connector Plug with Wire Leads AT022 Unassembled Connector Plug and Pins C3 Connector plug body: JST model ZHR-6 Crimp connector pins: JST model SZH-002T-P0.5 Wire leads: 28-26AWG; 12-inch, unstripped; Blue for Pin 1 No Code No Connector Plug 1 connector plug and 8 crimp connector pins only (no wire leads provided). Recommended connector plug for assembly: JST model number ZHR-6 Matching wire leads: 28-26AWG Recommended crimp connector pins: JST model SZH-002T-P0.5 for 28-26AWG wire leads or SZH-003T-P0.5 for 32-28AWG wire leads. TYPICAL SWITCH DIMENSIONS NKK P/N This Side (5.0) .197 Pin 1 (1.1)R Typ .043 (25.1) .988 (19.6) Dia .772 (26.0) Dia 1.024 (22.9) Dia .902 (1.5) .059 (5.3) .209 (21.4) .843 (2.3) .091 (22.8) Dia .898 Recommended Panel Thickness Range: .098” ~ .197” (2.5mm ~ 5.0mm) 6 5 4 3 2 1 Terminal Connector Detail FP0115CAC1FF LEGENDS Easily create and submit your own legends using our new on-line Legend Maker. LM Visit www.nkkswitches.com For other legend support options, customers may either contact the factory or utilize the general information and basic specifications presented below. Suggested Printable Area for FP01 Cap T ER AL Recommended Methods: Pad Print or Laser Etch on cap. Epoxy based ink is recommended. (16.56) Dia .475 (19.6) Dia .772 (1.52) Typ .060 Shaded area is printable area. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07