NPC CF5012ANB Low-current consumption crystal oscillator module ic Datasheet

CF5012 series
Low-current Consumption Crystal Oscillator Module ICs
OVERVIEW
The CF5012 series are low-current consumption 3rd-harmonic crystal oscillator module ICs. Internal circuit
optimization means these devices have reduced current consumption in comparison with our existing 3rd-harmonic oscillator devices. The crystal oscillator circuit has a built-in thin-film feedback resistor with good temperature characteristics and built-in capacitors with excellent frequency response, resulting in a stable 3rdorder overtone oscillator with only the connection of a crystal element.
FEATURES
■
■
■
■
■
■
3rd-harmonic oscillation
2.7 to 3.6V operating supply voltage range
30 to 45MHz recommended operating frequency
range
Inverter amplifier feedback resistor built-in
Oscillator capacitors CG , CD built-in
Output three-state function
(high impedance in standby mode)
■
■
■
■
■
fO output frequency (oscillator frequency)
8mA output drive capability (VDD = 2.7V)
6.5mA (typ) low current consumption
(VDD = 3V, CL = 15pF, f = 40MHz)
CMOS output duty level
Chip form (CF5012×××)
SERIES CONFIGURATION
Version
CF5012ANB
Recommended
operating
frequency [MHz]
gm ratio
Built-in capacitance [pF]
30 to 45
1.0
CG
CD
8
15
Rf [kΩ]
3.1
Note: Recommended operating frequency is not the guaranteed value but is measured using NPC’s standard crystal.
ORDERING INFORMATION
Device
Package
CF5012×××–1
Chip form
NIPPON PRECISION CIRCUITS INC.—1
CF5012 series
PAD LAYOUT
(Unit:µm)
VDD
Y
Q
(920,1180)
HA5012ANB
(0,0) INHN XTN
XT
VSS
X
Chip size: 0.92 × 1.18 mm
Chip thickness: 300 ± 30 µm
Chip base: VDD level
PIN DESCRIPTION and PAD DIMENSIONS
Pad dimensions [µm]
Name
I/O
Description
X
Y
INHN
I
Output state control input. High impedance when LOW. Pull-up resistor built in
195
174.4
XT
I
Amplifier input
385
174.4
XTN
O
Amplifier output
575
174.4
VSS
–
Ground
765
174.4
Q
O
Output. Output frequency. High impedance in standby mode
757.6
1017.6
VDD
–
Supply voltage
165.4
1014.6
Crystal oscillator connection pins.
Crystal oscillator connected between XT and XTN
BLOCK DIAGRAM
VDD VSS
XTN
CG
Rf
CD
XT
Q
INHN
Substrate potential: VDD
NIPPON PRECISION CIRCUITS INC.—2
CF5012 series
SPECIFICATIONS
Absolute Maximum Ratings
VSS = 0V
Rating
Unit
Supply voltage range
Parameter
Symbol
VDD
−0.5 to +7.0
V
Input voltage range
VIN
−0.5 to VDD + 0.5
V
VOUT
−0.5 to VDD + 0.5
V
Output voltage range
Condition
Operating temperature range
Topr
−40 to +85
°C
Storage temperature range
Tstg
−65 to +150
°C
Output current
IOUT
25
mA
Recommended Operating Conditions
VSS = 0V, f ≤ 45MHz, CL = 15pF unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
Supply voltage
VDD
2.7
–
3.6
V
Input voltage
VIN
VSS
–
VDD
V
TOPR
−20
–
+80
°C
Operating temperature
Electrical Characteristics
VDD = 2.7 to 3.6V, VSS = 0V, Ta = −20 to +80°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
HIGH-level output voltage
VOH
Q: Measurement cct 1, VDD = 2.7V, IOH = 8mA
2.2
2.4
–
V
LOW-level output voltage
VOL
Q: Measurement cct 2, VDD = 2.7V, IOL = 8mA
–
0.3
0.4
V
VOH = VDD
–
–
10
µA
VOL = VSS
–
–
10
µA
IZ
Q: Measurement cct 2, INHN = LOW,
VDD = 3.6V
HIGH-level input voltage
VIH
INHN
0.7VDD
–
–
V
LOW-level input voltage
VIL
INHN
–
–
0.3VDD
V
Current consumption
IDD
Measurement cct 3, load cct 1, INHN = open, CL = 15pF,
f = 40MHz
–
6.5
13
mA
INHN pull-up resistance
RUP
Measurement cct 4
40
100
250
kΩ
Rf
Measurement cct 5
2.63
3.1
3.57
kΩ
7
8
9
pF
13
15
17
pF
Output leakage current
Feedback resistance
Built-in capacitance
CG
CD
Design value, determined by the internal wafer pattern
NIPPON PRECISION CIRCUITS INC.—3
CF5012 series
Switching Characteristics
VDD = 2.7 to 3.6V, VSS = 0V, Ta = −20 to +80°C unless otherwise noted.
Rating
Parameter
Symbol
Condition
Unit
min
typ
max
Output rise time
tr
Measurement cct 3, load cct 1, 0.1VDD to 0.9VDD , CL = 15pF
–
2.0
4.0
ns
Output fall time
tf
Measurement cct 3, load cct 1, 0.9VDD to 0.1VDD , CL = 15pF
–
2.0
4.0
ns
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.0V,
CL = 15pF, f = 40MHz
40
–
60
%
–
–
100
ns
–
–
100
ns
Output duty cycle1
Duty
Output disable delay time
tPLZ
Output enable delay time
tPZL
Measurement cct 3, load cct 1, Ta = 25°C, VDD = 3.0V,
CL = 15pF
1. Monitored in sample lots.
Current consumption and Output waveform with NPC’s standard crystal
Cb
L
Ca
f (MHz)
R (Ω)
L (mH)
Ca (fF)
Cb (pF)
40
20.53
11.34
1.396
3.989
R
FUNCTIONAL DESCRIPTION
Standby Function
When INHN goes LOW, the oscillator output on Q goes high impedance.
INHN
Q
Oscillator
HIGH (or open)
fO output frequency
Normal operation
LOW
High impedance
Normal operation
NIPPON PRECISION CIRCUITS INC.—4
CF5012 series
MEASUREMENT CIRCUITS
Measurement cct 1
Measurement cct 4
VDD
C1
Signal
Generator
XT
VDD
Q
R1
R2
VSS
RUP =
VDD
IPR
INHN
VSS
VOH
Q output
0V
IPR
A
2.0VP−P , 10MHz sine wave input signal
C1 : 0.001µF
R1 : 50Ω
R2 : 275Ω
Measurement cct 2
Measurement cct 5
IOL, IZ
VDD
IZ
VDD
XT
A
Q
INHN VSS
Rf =
XTN
V VOL
VDD
IRf
VSS
A
IRf
Measurement cct 3
Load cct 1
A
XT
X'tal
IDD
Q output
CL
VDD
(Including probe capacitance)
Q
XTN
VSS INHN
CL = 15pF
NIPPON PRECISION CIRCUITS INC.—5
CF5012 series
Switching Time Measurement Waveform
Tr , Tf , Duty
Q output
0.9V DD
0.9V DD
0.1V DD
0.1V DD
DUTY measurement
voltage (0.5V DD )
TW
tr
tf
Output duty cycle
DUTY measurement
voltage (0.5V DD)
Q output
TW
DUTY= TW/ T
T
100 (%)
Output Enable/Disable Delay
INHN
VIH
VIL
tPZL
tPLZ
Q output
INHN input waveform tr = tf
10ns
NIPPON PRECISION CIRCUITS INC.—6
CF5012 series
NIPPON PRECISION CIRCUITS INC. reserves the right to make changes to the products described in this data sheet in order to
improve the design or performance and to supply the best possible products. Nippon Precision Circuits Inc. assumes no responsibility for
the use of any circuits shown in this data sheet, conveys no license under any patent or other rights, and makes no claim that the circuits
are free from patent infringement. Applications for any devices shown in this data sheet are for illustration only and Nippon Precision
Circuits Inc. makes no claim or warranty that such applications will be suitable for the use specified without further testing or modification.
The products described in this data sheet are not intended to use for the apparatus which influence human lives due to the failure or
malfunction of the products. Customers are requested to comply with applicable laws and regulations in effect now and hereinafter,
including compliance with export controls on the distribution or dissemination of the products. Customers shall not export, directly or
indirectly, any products without first obtaining required licenses and approvals from appropriate government agencies.
NIPPON PRECISION CIRCUITS INC.
4-3, Fukuzumi 2-chome, Koto-ku,
Tokyo 135-8430, Japan
Telephone: +81-3-3642-6661
Facsimile: +81-3-3642-6698
http://www.npc.co.jp/
Email: [email protected]
NC0111AE 2002.01
NIPPON PRECISION CIRCUITS INC.—7
Similar pages