MICROCIRCUIT DATA SHEET Original Creation Date: 05/20/99 Last Update Date: 05/04/01 Last Major Revision Date: MNDS26F32M-X-RH REV 0C0 QUAD DIFFERENTIAL LINE RECEIVERS ALSO AVAILABLE GUARANTEED TO 100K RAD(Si) TESTED TO MIL-STD-883, METHOD 1019.5, CONDITION A General Description The DS26F32 is a quad differential line receiver designed to meet the requirements of EIA Standards RS-422 and RS-423, and Federal Standards 1020 and 1030 for balanced and unbalanced digital data transmission. The DS26F32 offers improved performance due to the use of state-of-the-art L-FAST bipolar technology. The L-FAST technology allows for higher speeds and lower currents by utilizing extremely short gate delay times. The device features an input sensitivity of 200mV over the input common mode range of +7.0V. The DS26F32 provides an enable function common to all four receivers and TRI-STATE outputs with 8.0 mA sink capability. Also, a fail-safe input/output relationship keeps the outputs high when the inputs are open. The DS26F32 offers optimum performance when used with the DS26F31 Quad Differential Line Driver. Industry Part Number NS Part Numbers DS26F32 SEE FEATURES SECTION DS26F32ME/883 DS26F32MER-QML DS26F32MJ-QMLV DS26F32MJ/883 DS26F32MJR-QML DS26F32MJRQMLV DS26F32MW-QMLV DS26F32MW/883 DS26F32MWG/883 DS26F32MWGRQMLV DS26F32MWR-QML DS26F32MWRQMLV Processing Subgrp Description Prime Die M632 Controlling Document 1 2 3 4 5 6 7 8A 8B 9 10 11 MIL-STD-883, Method 5004 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 Features - Military temperature range - Input voltage range of +7.0V (differential or common mode) +0.2V sensitivity over the input voltage range. - High input impedance - Operation from single +5.0V supply - Input pull-down resistor prevents output oscillation on unused channels - TRI-STATE outputs, with choice of complementary enables, for receiving directly on a data bus CONTROLLING DOCUMENTS: DS26F32ME/883 5962-7802005M2A DS26F32MER-QML 5962R7802005Q2A DS26F32MJ-QMLV 5962-7802005VEA DS26F32MJ/883 5962-7802005MEA DS26F32MJR-QML 5962R7802005QEA DS26F32MJRQMLV 5962R7802005VEA DS26F32MW-QMLV 5962-7802005VFA DS26F32MW/883 5962-7802005MFA DS26F32MWG/883 5962-7802005MZA DS26F32MWGRQMLV 5962R7802005VZA DS26F32MWR-QML 5962R7802005QFA DS26F32MWRQMLV 5962R7802005VFA 2 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 (Absolute Maximum Ratings) (Note 1) Storage Temperature Range -65 C < Ta < +150 C Operating Temperature Range -55 C < Ta < +125 C Lead Temperature Soldering, 60 seconds Supply Voltage 300 C 7.0V Common Mode Voltage Range +25V Differential Input Voltage +25V Enable Voltage 7.0V Output Sink Current 50mA Maximum Power Dissipation (Pd) @ +25C (Note 2) 500mW Thermal Resistance (JA) J package W package E package Note 1: Note 2: 100 C/W 142 C/W 87 C/W "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Derate J package 10.0mW/C above +25C, Derate W package 7.1mW/C above +25C, Derate E package 11.5mW/C above +25C Recommended Operating Conditions Operating Temperature -55 C < Ta < +125 C Supply Voltage 4.5V to 5.5V 3 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 Electrical Characteristics DC PARAMETERS: (SEE Note 5) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: Vcc = 5V SYMBOL Iin PARAMETER Input Current CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vcc=4.5V, Vin=15V (Pin under test), other inputs -15V <= Vin <= +15V 2.3 mA 1, 2, 3 Vcc=5.5V, Vin=-15V (Pin under test), other inputs -15V <= Vin <= +15V -2.8 mA 1, 2, 3 Iil Logical "0" Enable Current Vcc = 5.5V, Ven = .4V -360 uA 1, 2, 3 Iih Logical "1" Enable Current Vcc = 5.5V, Vin = 2.7V 10 uA 1, 2, 3 Ii Logical "1" Enable Current Vcc = 5.5V, Vin = 5.5V 50 uA 1, 2, 3 Vik Input Clamp Voltage (Enable) Vcc = 4.5V, Iin = -18mA -1.5 V 1, 2, 3 Voh Logical "1" Output Voltage Vcc = 4.5V, Ioh = -440uA, Delta Vin = 1V, Ven = .8 = Ven V 1, 2, 3 Vol Logical "0" Output Voltage Vcc = 4.5V, Ven = .8V = Ven, Iol = 4mA, Delta Vin = -1V .4 V 1, 2, 3 Vcc = 4.5V, Ven = .8V = Ven, Iol = 8mA, Delta Vin = -1V .45 V 1, 2, 3 2.5 Icc Supply Current Vcc = 5.5V, All Vin = Gnd, Ven = 0V, Ven = 2V 50 mA 1, 2, 3 Ioz Off-State Output Current Vcc = 5.5V, Vo = .4V, Ven = .8V, Ven = 2V -20 uA 1, 2, 3 Vcc = 5.5V, Vo = 2.4V, Ven = .8V, Ven = 2V 20 uA 1, 2, 3 Rin Input Resistance -15 <= Vcm <= 15V 14 Vth Differential Input Voltage Vcc = 4.5V, -7V <= Vcm <= 7V, Ven = Ven = 2.5V, Vo = 0.45/2.5V 2 -.2 .2 V 1, 2, 3 Vcc = 5.5V, -7V <= Vcm <= 7V, Ven = Ven = 2.5V, Vo = 0.45/2.5V 2 -.2 .2 V 1, 2, 3 .8 V 1, 2, 3 2 V 1, 2, 3 -15 mA 1, 2, 3 mA 1, 2, 3 Vil Logical "0" Input Voltage (Enable) Vcc = 5.5V 2 Vih Logical "1" Input Voltage (Enable) Vcc = 4.5V 2 Isc (min) Output Short Circuit Current Vcc = 4.5V, Vo = 0V, Delta Vin = 1V Isc (max) Output Short Circuit Current Vcc = 5.5V, Vo = 0V, Delta Vin = 1V 4 KOhm 1, 2, 3 -85 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 Electrical Characteristics AC PARAMETERS: PROPAGATION DELAY TIME: (SEE NOTE 5) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: Vcc = 5V SYMBOL PARAMETER tPLH CONDITIONS NOTES Cl = 50pF Cl = 15pF tPHL Cl = 50pF Cl = 15pF tPZH Enable Time Cl = 50pF Cl = 15pF tPZL Enable Time Cl = 50pF Cl = 15pF tPHZ Disable Time Cl = 50pF Cl = 5pF tPLZ Disable Time Cl = 50pF Cl = 5pF 5 PINNAME MIN MAX UNIT SUBGROUPS 4, 5 23 nS 9 4, 5 31 nS 10, 11 3, 5 22 nS 9 3, 5 30 nS 10, 11 4, 5 23 nS 9 4, 5 31 nS 10, 11 3, 5 22 nS 9 3, 5 30 nS 10, 11 4, 5 18 nS 9 4, 5 29 nS 10, 11 3, 5 16 nS 9 3, 5 27 nS 10, 11 4, 5 20 nS 9 4, 5 29 nS 10, 11 3, 5 18 nS 9 3, 5 27 nS 10, 11 4, 5 55 nS 9 4, 5 62 nS 10, 11 3, 5 20 nS 9 3, 5 27 nS 10, 11 4, 5 30 nS 9 4, 5 42 nS 10, 11 3, 5 18 nS 9 3, 5 30 nS 10, 11 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 Electrical Characteristics DC PARAMETERS - DRIFT VALUES (The following conditions apply to all the following parameters, unless otherwise specified.) DC: NOTE::This section applies to -QMLV devices only and shall be read & recorded at TA = +25C before and after each burn-in and shall not change by more than the limits indicated. The delta rejects shall be included in the PDA calculation. SYMBOL Voh Vol Iin PARAMETER CONDITIONS NOTES Logical "1" Output Voltage Vcc = 4.5V, Ioh = -440uA, Delta Vin = 1V, Ven = 0.8V Logical "0" Output Voltage Vcc = 4.5V, Iol = 4mA, Delta Vin = -1V, Ven = Input Current Note Note Note Note Note 1: 2: 3: 4: 5: PINNAME MIN MAX UNIT SUBGROUPS -250 250 mV 1 -45 45 mV 1 Vcc = 4.5V, Iol = 8mA, Delta Vin = -1V, Ven = 0.8V = Ven -45 45 mV 1 Vcc = 4.5V, Vin=15V (Pin under test), other inputs -15V <= Vin <= +15V -0.28 0.28 mA 1 Vcc = 5.5V, Vin=-15V (Pin under test), other inputs -15V <= Vin <= +15V -0.28 0.28 mA 1 = Ven 0.8V = Ven Power dissipation must be externally controlled at elevated temperatures. Parameter tested go-no-go only. Tested at 50pF guarantees limit at 15 & 5pF. Tested at 50pF, system capacitance exceeds 5 to 15pF. Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiaton end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019.5, Condition A. 6 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 Graphics and Diagrams GRAPHICS# DESCRIPTION E20ARE LCC (E), TYPE C, 20 TERMINAL(P/P DWG) J16ARL CERDIP (J), 16 LEAD (P/P DWG) W16ARL CERPACK (W), 16 LEAD (P/P DWG) WG16ARC CERAMIC SOIC (WG), 16 LEAD (P/P DWG) See attached graphics following this page. 7 MICROCIRCUIT DATA SHEET MNDS26F32M-X-RH REV 0C0 Revision History Rev ECN # Originator Changes 0A0 M0003443 08/22/00 Rel Date Rose Malone Initial MDS Release: MNDS26F32M-X-RH, Rev. 0A0 - Added reference to Rad Hard. Archive MNDS26F32M-X, Rev. 0B0, Replace By MNDS26F32M-X-RH, Rev. 0A0. 0B0 M0003730 05/04/01 Rose Malone Update MDS: MNDS26F32M-X-RH, Rev. 0A0 to MNDS26F32M-X-RH, Rev. 0B0. Changed Main Table and Features Section reference to Rad Hard NS Part Numbers and 5962 SMD Drawings for J, E and W Packages. Rad Hard Level from 300K to 100K. 0C0 M0003796 05/04/01 Rose Malone Update MDS: MNDS26F32M-X-RH, Rev. 0B0 to MNDS26F32M-X-RH, Rev. 0C0. Added to Main Table NS Part Numbers Section and Features Section reference to WG package and SMD numbers and Marketing Dwg. to Graphics Section. 8