Gennum GS9021A Genlinx -tm ii gs9021a edh coprocessor Datasheet

GENLINX ™II GS9021A
EDH Coprocessor
DATA SHEET
DESCRIPTION
• Error Detection and Handling (EDH) according to
SMPTE RP-165
The GS9021A implements error detection and handling
(EDH) according to SMPTE RP-165. Interfacing to the
parallel inputs of either the GS9002, GS9022 or GS9032
serial digital encoders, the GS9021A is primarily used on
the transmit end of the SDI interface. The GS9021A
provides EDH insertion and extraction for 4ƒsc NTSC, 4ƒsc
PAL and all component PAL and NTSC standards including
4:2:2 (13.5MHz and 18MHz luminance sampling), and
4:4:4:4.
• drop-in replacement for the GS9021
• EDH insertion and extraction in one device
• auto-standard operation with override via host
interface
• noise immune extraction of HVF timing signals
• TRS insertion/correction and ANC header correction
for all standards
The GS9021A generates noise immune timing signals such
as horizontal sync, vertical blanking and field ID. In
addition, TRS-ID correction/insertion and data blanking are
implemented for all standards.
• ITU-R-601 output clipping for active picture area
• selectable I²C interface or 8-bit parallel port for access
to EDH flags and device configuration bits
• all error flags available on dedicated output pins
A host interface, configurable as an 8-bit parallel interface
or an I²C (I²C is a registered trademark of Philips) serial
interface allows for communication with a microcontroller.
The interface can be used to read and/or write the
complete set of error flags and override the flag status prior
to re-transmission. A 5-bit flag port provides access to all
error flags on dedicated pins for applications where the
microcontroller is not used. The device automatically
determines the operating standard, but this can be
overridden through the programming interface.
• 24-bit Errored Field counter
• BYPASS mode to bypass EDH insertion/updating
• dynamic blanking control input
• 8-bit or 10-bit compatibility
• up to 54MHz operating frequency
• seamless flag-mapping with GS9020 serial digital
video input processor
APPLICATIONS
ORDERING INFORMATION
EDH processing for SMPTE 259M serial digital interfaces for
composite and component standards including 4:4:4:4 at
540Mb/s; Noise immune digital sync and timing generation.
Source, destination, distribution and test equipment;
General purpose, TRS formatted, blank video stream
generator with EDH.
PART NUMBER
PACKAGE
TEMPERATURE
GS9021ACFU
64 pin LQFP Tray
0°C to 70°C
HOSTIF_MODE FLAG_MAP
EDH FLAG
EXTRACTION
10
DIN
CRC
COMPARISON/
CALCULATION
VBLANKS/L
FLYWDIS
H, V, F
5
HVF
FLYWHEEL
TRS_ ERROR
TRS
DETECTION
TRS
COMPARE
ANCILLARY
CHECKSUM
CALCULATION/
COMPARISON
BLANK_EN
CLIP_TRS
ERRORED
FIELD
COUNTER
DEDICATED
FLAG PORT
8-BIT
PARALLEL
INTERFACE
BYPASS_EDH
FLAGS
10
ERROR FLAGS
&
FORMAT PACKET
MUX
10
LSB_TOP
DATA BUS 10
REVERSAL
ANCILLARY
CHECKSUM
CORRECTION
10
I²C INTERFACE
HOST INTERFACE/
FLAG PORT
CRC_MODE
NEW CRC
CALCULATION
ITU-R-601 CLIPPING
TRS BLANKING
TRS INSERTION/
CORRECTION
DOUT
R/T
10
I²C is a registered
Trademark of Philips
BLOCK DIAGRAM
Revision Date: January 2004
Document No. 19983 - 1
GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3
Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected]
www.gennum.com
GS9021A
FEATURES
ABSOLUTE MAXIMUM RATINGS
PARAMETER
VALUE
Supply Voltage
-0.3V to 6.0V
Input Voltage Range (any input)
-0.3 to VDD + 0.3V
Operating Temperature Range
0°C to 70°C
GS9021A
Storage Temperature
-55°C to 150°C
Lead Temperature (soldering, 10 sec)
260°C
DC ELECTRICAL CHARACTERISTICS
VDD = 5.0V, TA = 0 to 70°C unless otherwise shown.
PARAMETER
SYMBOL
Supply Voltage
VDD
Supply Current Unloaded
ΙDD
TTL Compatible CMOS Inputs
CONDITION
MIN
TYP
MAX
UNITS
4.75
5.0
5.25
V
27MHz
-
39
-
mA
54MHz
-
75
-
mA
VILMAX
-
-
0.8
V
VIHMIN
2.0
-
-
V
-
-
150
µA
-
-
1
-
10
-
ΙIN
VIN = VDD or GND
CIN
TTL Compatible CMOS Outputs
NOTES
1
2
pF
VOLMAX
at ΙOUT
-
-
0.4
V
VOHMIN
at ΙOUT
2.4
-
-
V
-
4
-
mA
3
-
2
-
mA
4
ΙOUT
NOTES
1. The following inputs have internal pull-up resistors: R/T. The following inputs have internal pull-down resistors: FLYWIS, LSB_TOP,
CRC_MODE, RESET, FLAG_MAP, HOSTIF_MODE and DIN[9:0]. To ensure reliable operation these pins should be externally
connected to GND or Vcc.
2. All other inputs.
3. The following outputs have 4mA drivers (typical): S[1:0], FL[4:0], DOUT[9:0], H, V and F[2:0].
4. The following outputs have 2mA drivers (typical): P[7:0].
2 of 26
19983 - 1
AC ELECTRICAL CHARACTERISTICS
VDD = 5.0V, TA = 0 to 70°C unless otherwise shown.
PARAMETER
SYMBOL
CONDITION
MIN
TYP
MAX
UNITS
-
-
54
MHz
Input Clock Frequency
NOTES
tPWL
7.4
-
-
ns
Clock Pulse Width High
tPWH
7.4
-
-
ns
Input Setup Time
tS
3
-
-
ns
1, 2
Input Hold Time
tH
3
-
-
ns
1, 2
Output Delay Time
tOD
with 10pF loading
-
-
15
ns
2
Output Hold Time
tOH
with 10pF loading
5
-
-
ns
2
Output Setup Time
tOS
with 10pF loading
3.5
-
-
ns
2,4
Flag Port Disable Time
tFDIS
with 25pF loading
-
-
15
ns
Flag Port Enable Time
tFEN
with 25pF loading
-
-
16
ns
I²C Clock Frequency
ƒSCL
-
-
400
kHz
Host Interface Setup Time
tHS
6
-
-
ns
Host Interface Hold Time
tHH
6
-
-
ns
Host Interface Output
Enable Time
tHEN
with 25pF loading
-
-
21
ns
Host Interface Output
Disable Time
tHDIS
with 25pF loading
-
-
10
ns
Reset Time Pulse Width
tRESET
100
-
-
ns
tLAT
8
8
8
clks
Device Latency
3
NOTES
1. See section 1.2 for a list of signals synchronous and asynchronous to PCLKIN.
2. See Figures 1 and 2.
3. Latency is defined as the number of clock cycles between the time when the data is latched into the device and when the
corresponding output data is clocked into the next device as shown in Figure 3.
4) Based upon 54MHz clock (18.5ns). Output Setup Time = Clock Period - Output Delay Time
3 of 26
19983 - 1
GS9021A
Clock Pulse Width Low
CLIP_TRS
FLYWDIS
BLANK_EN
LSB_TOP
BYPASS_EDH
VBLANKS/L
CRC_MODE
VDD
GND
R/T
RESET
F2
F1
F0
H
V
PIN CONNECTIONS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
48
47
46
45
44
43
42
GS9021A
41
TOP VIEW
40
39
38
37
36
35
34
33
17 18 19 20 21 22 23 24 25 26 2728 29 30 31 32
DOUT9
DOUT8
DOUT7
DOUT6
DOUT5
DOUT4
DOUT3
VDD
GND
DOUT2
DOUT1
DOUT0
FLAG_MAP
F_R/W
FL4
FL3
SCL/P4
SDA/P3
A2/P2
A1/P1
A0/P0
R/W
A/D
CS
HOSTIF_MODE
VDD
GND
S0
S1
FL0
FL1
FL2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
GS9021A
DIN9
DIN8
DIN7
DIN6
DIN5
DIN4
DIN3
VDD
GND
DIN2
DIN1
DIN0
PCLKIN
P7
P6
P5
PIN DESCRIPTIONS
NUMBER
SYMBOL
TYPE
DESCRIPTION
1-7, 10-12
DIN[9:0]
I
Parallel digital video data inputs.
13
PCLKIN
I
Parallel clock input.
14-16
P[7:5]
I/O
In parallel port mode, these are bits 7:5 of the host interface address/data bus. In
I²C mode, these pins must be set LOW.
17
SCL/P4
I/O
In parallel port mode, this is bit 4 of the host interface address/data bus. In I²C
mode, this is the serial clock input for the I²C port.
18
SDA/P3
I/O
In parallel port mode, this is bit 3 of the host interface address/data bus. In I²C
mode, this is the serial data pin for the I²C port.
19-21
A[2:0]/P[2:0]
I/O
In parallel port mode, these are bits 2:0 of the host interface address/data bus. In
I²C mode, these are input bits which define the I²C slave address for the device.
22
R/W
I
Parallel port read/write control. When HIGH, the parallel port is configured as an
output (read mode). When LOW, the parallel port is configured as an input (write
mode). In I²C mode, this pin must be set HIGH.
23
A/D
I
Parallel port address/data bus control. When HIGH, the parallel port is used for
address input. When LOW, the parallel port is used for data input or output. In
I²C mode, this pin must be set LOW.
24
CS
I
Parallel port chip select. When CS is LOW and R/W is HIGH, the GS9021A drives
the address/data bus. When CS is LOW and R/W is LOW, the user should drive
the address/data bus. When CS is HIGH, the address/data bus is in a high
impedance state (Hi - Z). In I²C mode, this pin must be set HIGH.
25
HOSTIF_MODE
I
Host Interface mode select. When HIGH, the host interface is configured for I²C
mode. When LOW, the host interface is configured for parallel port mode.
4 of 26
19983 - 1
PIN DESCRIPTIONS
SYMBOL
TYPE
DESCRIPTION
28, 29
S[1:0]
I/O
Control bits which select whether FF, AP, or ANC EDH flags are active on the EDH
flag data port (FL[4:0]). In FLAG_MAP mode, the S[1:0] pins become outputs
(see device description).
30-34
FL[4:0]
I/O
EDH flag data port to allow access to the EDH flags.
35
F_R/W
I
Flag port read/write control. When HIGH, FL[4:0] are configured as outputs
allowing EDH flags to be read from the device. When LOW, FL[4:0] are
configured as inputs allowing EDH flags to be overwritten into the outgoing EDH
packet. In FLAG_MAP mode this pin must be set HIGH.
36
FLAG_MAP
I
FLAG_MAP mode enable. When HIGH, FLAG_MAP mode is enabled. When
LOW, FLAG_MAP mode is disabled.
37-39, 42-48
DOUT[9:0]
O
Parallel digital video data outputs.
49
V
O
Vertical sync indication.
50
H
O
Horizontal sync indication.
51-53
F[2:0]
O
Field indication. F2 is the MSB.
54
RESET
I
Reset. When LOW, the internal control circuitry is reset.
55
R/T
I
Receive/Transmit mode select. When HIGH, the device operates in receive mode.
When LOW, the device operates in transmit mode.
58
CRC_MODE
I
CRC_MODE enable. When HIGH, CRC_MODE is enabled. When LOW,
CRC_MODE is disabled.
59
VBLANKS/L
I
Vertical blanking interval control. For NTSC signals, when VBLANKS/L is set LOW
the 19 line blanking interval is selected and when set HIGH the 9 line blanking
interval is selected. For PAL D2 signals, when VBLANKS/L is set LOW the 17 line
blanking interval is selected and when set HIGH the 7 line blanking interval is
selected. For PAL component signals VBLANKS/L should be set LOW.
60
BYPASS_EDH
I
Bypass EDH control. When HIGH, the device allows the EDH packet to pass
through unaltered.
61
LSB_TOP
I
Data output LSB position control. When HIGH, the video data output bus is
reversed, placing the LSB at pin 48.
62
BLANK_EN
I
Blanking enable. When LOW, incoming data words are set to appropriate
blanking levels.
63
FLYWDIS
I
Flywheel disable. When HIGH, the internal flywheel is disabled. When LOW, the
internal flywheel is enabled.
64
CLIP_TRS
I
Clip and TRS correction control. When HIGH, the TRS Blanking, ITU-R-601
clipping and TRS insertion features are enabled.
8, 26, 41, 57
VDD
Power supply (nominally +5V).
9, 27, 40, 56
GND
Ground.
5 of 26
19983 - 1
GS9021A
NUMBER
DETAILED DESCRIPTION
The GS9021A EDH coprocessor consists of five major
blocks:
1.2 Parallel Clock Inputs
PIN
1. Data Input/Output Block (with automatic standard
detect)
LOGIC OPR
HOST BIT
PCLKIN
2. Flywheel Block
4. Data Processing Block
5. Host Interface (HOSTIF) Block
The following convention is used to differentiate device pins
from HOST interface table bits.
PIN
LOGIC OPR
XX
The PCLKIN pin is the input used to clock the video data
into the GS9021A, and serves as the reference to which all
synchronous inputs and outputs are timed. The following
table shows which pins are synchronous with PCLKIN and
which are not. Timing for synchronous I/O is found in
Figures 1 and 2.
HOSTIF
SYNCHRONOUS
ASYNCHRONOUS
FL[4:0]
P[7:5]
S[1:0]
SCL/P4
FIFO_RESET
INTERRUPT
DOUT[9:0]
SDA/P3
F[2:0]
A[2:0]/P[2:0]
V
R/W
YY
LOGIC OPR (logic operator) gives the combinational
relationship (if one exists), between pins which also have a
corresponding HOST bit. This operator governs the signal
the GS9021A receives. The following is the list of possible
logic operators and their meaning.
H
A/D
LOGIC OPR
MEANING
ANC_DATA
CS
AND
XX AND YY
BLANK_EN
FLAG_MAP
OR
XX OR YY
F_R/W
RESET
>
XX takes precedence over YY
NO_EDH
CRC_MODE
<
YY takes precedence over XX
STD[3:0]
VBLANKS/L
TRS_ERROR
HOSTIF_MODE
DIN[9:0]
FIFOE/S
1. DATA INPUT/OUTPUT BLOCK
1.1 Parallel Digital Video Data Inputs
FLYWDIS
BYPASS_EDH
PIN
LOGIC OPR
HOST BIT
SDO_MODE
DOUT[9:0]
ANC_CHKSM
CLIP_TRS
Parallel digital video data is supplied to the GS9021A chip
via the DIN[9:0] input pins. The data is clocked into the
GS9021A by the rising edge of PCLKIN.
Eight input signal standards are supported: Composite,
4:2:2 Component with 13.5MHz Y sampling, 4:2:2 16 x 9
wide screen with 18 MHz Y sampling, and 4:4:4:4
Component Single Link with 13.5MHz Y sampling, all in
both NTSC and PAL formats (See Table 1). Both 8 and 10
bit inputs are supported. However, when using 8 bit data,
the 2 LSBs of the input must be tied to GND.
6 of 26
19983 - 1
GS9021A
3. EDH Block
1.3 Parallel Digital Video Data Outputs
PIN
LOGIC OPR
to as much as four frames when switching between PAL
and NTSC standards. If this delay is intolerable, the user
can manually set the standard through the HOSTIF write
table. To set the standard manually, the STD_SEL bit must
be set HIGH and the S bit and STD[3:0] bits set
accordingly. The default standard upon resetting the device
is NTSC 4:2:2 component (13.5MHz Y sampling).
HOST BIT
DOUT[9:0]
LSB_TOP
The default position of the LSB is DOUT0. Asserting the
LSB_TOP pin HIGH on the GS9021A reverses the order of
the output bits, placing the LSB at DOUT9 and simplifying
board layout in some applications. Figure 11 shows a
simple application circuit illustrating the connections to the
GS9032.
The S bit, used for single link data standards only, is
encoded in the TRSID word and indicates if the data is in
RGB or YCRCB format as per SMPTE RP174. In automatic
standard detection mode, the S bit can be read from the
HOSTIF read table. In manual mode, the S bit must be set
in the HOSTIF write table.
2. FLYWHEEL BLOCK
2.1 FVH Flywheel
1.4 Automatic Standard Detection
PIN
LOGIC OPR
HOST BIT
PIN
LOGIC OPR
HOST BIT
FLYWDIS
OR
FLYWDIS
SWITCHFLYW
STD_SEL
STD[3:0]
S
The device automatically detects the incoming video
standard. The detected standard is encoded on the
STD[3:0] bits of the HOSTIF read table as shown in Tables 1
and 4.
TABLE 1
STANDARD NAME
STD[3:0]
NTSC 4:2:2 Component with 13.5MHz Y sampling
0000
NTSC Composite
0001
NTSC 4:2:2 16x9 Widescreen with 18MHz Y
sampling
0010
NTSC 4:4:4:4 Single Link with 13.5MHz Y sampling
0011
PAL 4:2:2 Component with 13.5MHz Y sampling
0100
PAL Composite
0101
PAL 4:2:2 16x9 Widescreen with 18MHz Y sampling
0110
PAL 4:4:4:4 Single Link with 13.5MHz Y sampling
0111
The flywheel’s primary function is to provide accurate field,
vertical, and horizontal output signals in the presence of
noisy or error prone input data. Flywheel synchronization is
based on the TRS words in the incoming data stream. The
FVH flywheel synchronizes to the incoming data stream in
less than two fields once the incoming standard has been
detected. Once synchronized, the TRS words in the
incoming data stream and those generated by the flywheel
are constantly compared to ensure that the flywheel
remains synchronized.
Noise insensitivity is accomplished by re-synchronizing the
flywheel to the data stream only if it is not aligned for long
periods of time. For component signals, four mismatches
between the EAV signal in the incoming and flywheel
generated signals over a window of eight lines will trigger
the flywheel to begin re-synchronization.
For composite signals, re-synchronization is triggered by
mismatches in the TRS encoded line numbers or field bits
for seven consecutive lines.
Noise immunity is included to ensure that momentary signal
corruption does not affect the automatic standards
detection function. This built in noise immunity results in
delayed detection time during power up and when
switching between standards. Delays range from as little as
eight lines when switching between component standards
The flywheel can be disabled by asserting the FLYWDIS
control signal HIGH. Disabling the flywheel will remove the
effective noise immunity. In this mode, FVH values will be
decoded directly from the incoming data stream rather than
being decoded from the flywheel. Note that when the
flywheel is disabled, TRS_BLANK and TRS_ INSERT will not
function correctly if enabled. Therefore, if the flywheel is
disabled, then so should TRS_BLANK and TRS_INSERT.
FLYWDIS is available as an input pin and as a bit in the
HOSTIF write table.
7 of 26
19983 - 1
GS9021A
The output of the device is 10-bit digital video data and is
present on the DOUT[9:0] output pins. The latency through
the device is 8 clock cycles and is illustrated in Figure 3.
The lines on which the LOW to HIGH transition occurs
conform to the SMPTE standards.
STANDARD
2.2 Accurate FVH Timing Signals
PIN
LOGIC OPR
F[2:0]
HOST BIT
VBLANKS/L=1
VBLANKS/L=0
NTSC 4:2:2 Component
(13.5MHz Y sampling)
9/272
19/282
NTSC 4:2:2 16x9 Widescreen
(18MHz Y sampling)
9/272
19/282
NTSC 4:4:4:4 Single Link
(13.5MHz Y sampling)
9/272
19/282
PAL 4:2:2 Component
(13.5MHz Y sampling)
22/335
22/335
PAL 4:2:2 16x9 Widescreen
(18MHz Y sampling)
22/335
22/335
PAL 4:4:4:4 Single Link
(13.5MHz Y sampling)
22/335
22/335
F[2:0]
V
H
VBLANKS/L
AND
For composite based standards, the V output signal is
asserted HIGH as described in the table below:
VBLANKS/L
The F[2:0] signals indicate the current field of the video
data. Three F bits are necessary to accommodate the
composite PAL standard which has 8 fields. For component
standards only F0 is used to represent F = 0 or F = 1. The
F[2:0] bits are available on dedicated output pins and via
the HOSTIF read table. Figure 4a and 4b illustrate the
position of the F[2:0] transition within a line for component
and composite signals, respectively. The lines on which the
transitions occur conform to the SMPTE standards.
NTSC
Composite
For component signals, the horizontal (H) signal is HIGH
during the horizontal blanking region of the output signal,
from EAV to SAV inclusive. For composite signals, the H
signal remains HIGH only for the 3FF, 000, 000, 000, and
TRSID words. Figure 4a and 4b illustrate the H output signal
timing for component and composite signals, respectively.
The vertical (V) signal timing is dependent on the incoming
video standard and the VBLANKS/L control signal. The
VBLANKS/L signal is available as an input pin and via the
HOSTIF write table and should be set to indicate the form of
the incoming data stream. This allows the flywheel to
correctly structure the V bit for flywheel synchronization,
TRS insertion, and TRS error indication.
PAL
Composite
VBLANKS/L=1
VBLANKS/L=0
from Line 525/ Sample
768 to Line 9/ Sample
767 inclusive
from Line 525/ Sample
768 to Line 19/ Sample
767 inclusive
AND
AND
from Line 263/ Sample
313 to Line 272/
Sample 767 inclusive
from Line 263/ Sample
313 to Line 282/
Sample 767 inclusive
VBLANKS/L=1
VBLANKS/L=0
from Line 623/ Sample
382 to Line 5/ Sample
947 inclusive
from Line 623/ Sample
382 to Line 15/ Sample
947 inclusive
AND
AND
from Line 310/ Sample
948 to Line 317/
Sample 947 inclusive
from Line 310/ Sample
948 to Line 327/
Sample 947 inclusive
2.3 TRS Errors
PIN
LOGIC OPR
HOST BIT
TRS_ERROR
For component based standards, the transition of the V
output signal within a line is shown in Figure 4a. The line on
which the V output signal transitions from HIGH to LOW is
summarized in the following table.
The flywheel is also used to indicate TRS errors. These
errors are detected by comparing the TRS in the incoming
data stream with the expected TRS based on the internal
flywheel.
8 of 26
19983 - 1
GS9021A
The SWITCHFLYW control signal is used in applications
where the data input to the GS9021A is switched between
two synchronous signals. In this case, the two signals may
be slightly misaligned and would normally require the
flywheel to completely re-synchronize. In this scenario, the
re-synchronization time would be undesirable. Asserting the
SWITCHFLYW bit of the HOSTIF write table HIGH allows the
flywheel to re-synchronize to the new incoming signal at the
end of the switching line. For this functionality to operate
properly, the two signals must both be in the active picture
portion of the switching line at the time of the switch.
If a mismatch occurs, the TRS_ERR signal is immediately
set HIGH and maintained HIGH until a correct TRS occurs.
The types of TRS errors detected are:
PIN
LOGIC OPR
HOST BIT
INCOMING ERROR FLAGS
TRS missing
OUTGOING ERROR FLAGS
•
TRS in wrong location
STICKY IN
•
TRS-ID is different from the one generated by the
flywheel
STICK OUT
GS9021A
•
OVERWRITE VALUES
The TRS_ERR signal is available via the HOSTIF read table.
TRS_ERR signal should only be considered valid if the
flywheel is enabled.
OVERWRITE CONTROL
RO_CTRL
RESERVED WORDS (INCOMING)
3. EDH PROCESSING BLOCK
RESERVED WORDS (OUTGOING)
This section describes the GS9021A’s EDH features and
functionality.
3.1 Receive and Transmit Modes
PIN
LOGIC OPR
HOST BIT
R/T
In normal operation, the GS9021A is configured for one of
two modes, Receive (R/T = HIGH) or Transmit (R/T = LOW)
mode.
Transmit mode is appropriate for equipment which accepts
video that has no EDH packets or source equipment which
must generate a video stream with EDH. Receive mode is
appropriate for equipment where the input data already
contains EDH information. When the GS9021A is configured
in receive mode, the device expects to find an EDH packet
in the incoming data stream. The encoded CRC values in
the incoming data stream are compared with the calculated
CRC values as discussed in more detail below. Error flags
are set based on the results of these comparisons. If no
EDH packet is present, a new EDH packet is inserted (as in
transmit mode) but the UES flags are set to 1. In transmit
mode, no comparison is performed but a new EDH packet
is inserted with the calculated CRC values. All flags are set
to 0, unless set otherwise by the HOSTIF or flag port. See
Table 2 for the effect of the different settings of R/T and
CRC_MODE. Receive or Transmit mode is set via the R/T
control pin.
3.2 Error Flags
All 15 EDH error flags can be read from the HOSTIF read
table. The INCOMING ERROR FLAGS represent the EDH
error flags present in the incoming EDH packet. The
OUTGOING ERROR FLAGS represent the EDH error flags
present in the outgoing EDH packet (after modification by
the GS9021A).
The INCOMING and OUTGOING ERROR FLAGS, the
incoming Validity bits (FFV and APV), and the EDH_CHKSM
bit can be made "sticky". Sticky error flags that detect an
error for a field remain asserted until a HOSTIF read is
performed on those error flags. Sticky mode allows the user
to perform HOSTIF reads on the error flags to detect if any
errors have occurred since the last read, and are
particularly useful when a read cannot be performed after
every field. When STICKY IN is asserted HIGH, the
incoming flags and validity bits are in sticky mode. When
STICKY OUT is asserted HIGH, the outgoing flags and the
EDH_CHKSM bit are in sticky mode. STICKY IN and
STICKY OUT are available in the HOSTIF write table. The
ERROR FLAGS and the EDH_CHKSM bit are sticky HIGH.
That is, once they are set HIGH, they remain HIGH until a
read operation. The validity bits are sticky LOW. That is,
once they are set LOW, they remain LOW until a read
operation.
In some applications, the user may wish to insert user
defined EDH error flags into the outgoing EDH packet. The
desired outgoing error flags are written into the OVERWRITE
VALUES words of the HOSTIF write table and are placed in
the outgoing EDH packet when the corresponding
OVERWRITE CONTROL bit is asserted HIGH. See Table 3
for Host Interface WRITE table.
The GS9021A also allows the user to overwrite the 7
reserved words of the OUTGOING EDH packet. When
RO_CTRL (Reserved Word Overwrite Control) is asserted
HIGH, the GS9021A overwrites the reserved words in the
OUTGOING EDH packet with those specified in the HOSTIF
write table. If RO_CTRL is LOW, the GS9021A does not alter
the reserved words. RO_CTRL is a control bit in the HOSTIF
write table. The reserved words of the INCOMING EDH
packet are also available via the HOSTIF read table.
9 of 26
19983 - 1
3.3 CRC Calculation And Updating
PIN
LOGIC OPR
HOST BIT
INCOMING FF CRC
OUTGOING FF CRC
OUTGOING AP CRC
Since the device has the potential of modifying the full-field
and active picture data with features like ITU-R-601 clipping
and TRS insertion, the full field and active picture CRC
values must be calculated for both the incoming and
outgoing data streams. The calculated CRC values based
on the incoming data stream are used for comparison with
the embedded CRC values. However, the calculated CRC
values based on the outgoing data stream are the ones
inserted into the data stream. As a result, the CRC values in
the outgoing data stream correctly reflect the contents of
the outgoing data stream.
The INCOMING FF and AP CRC values for the Full Field
(FF) and Active Picture (AP) regions can be read from the
HOSTIF read table. Similarly, the OUTGOING (calculated)
FF and AP CRC values for the Full Field and Active Picture
regions can be read from the HOSTIF read table.
3.4 Validity Bit
PIN
LOGIC OPR
HOST BIT
FFV
APV
The VALIDITY (V) bits (as per SMPTE 165) present in the
incoming EDH packet are used to indicate whether the CRC
values are valid or invalid. If the V bit is HIGH, the CRC
value is considered valid. In this case, the incoming CRC
value is compared with the calculated CRC value to identify
errors. If the V bit is LOW, the incoming CRC is invalid and a
CRC comparison is not performed. If the device receives an
EDH packet with the V bit set LOW it behaves as follows:
1. EDH = 0 (Not asserted for an invalid CRC)
2. EDA = EDAin "OR" EDHin (EDA calculated as usual)
3. A new calculated CRC value replaces the invalid one in
the output EDH packet
4. The V bit will be set HIGH in the output EDH packet
The incoming V bits for the Full Field and Active Picture
regions are available in the HOSTIF read table as FFV and
APV, respectively. Outgoing full field (FFV) and active
picture (APV) validity bits are set HIGH unless explicitly
over-written through the HOSTIF write table or the flag port.
3.5 Ancillary Checksum Verification
PIN
LOGIC OPR
HOST BIT
ANC_CHKSM
EDH_CHKSM
For each received ANC packet in the incoming data, the
device compares the calculated checksum value to the
embedded checksum for that ANC packet.
If the
checksum values do not match for any ANC packets within
a field, an error is reported via the ANC EDH flag in the EDH
packet. In addition, if the ANC_CHKSM input pin or
HOSTIF write table bit is asserted HIGH, the ancillary
checksum correction block is enabled and the checksum in
the ANC packet is replaced with the calculated one. This
update is required to prevent the ANC data error from being
flagged at every downstream EDH chip.
When implementing applications which use the EDH core
(ie. BYPASS_EDH set LOW), the ANC_CHKSM function will
indicate a downstream FF/AP EDH error when an illegal/
non-allowed (3FCH-3FFH) ANC_CHKSM input value is
detected. As such, these values should not be present in
the incoming data and the corresponding FF/AP EDH errors
should not occur. However, if the user wishes to disable the
ANC_CHKSM function, it can be deactivated by setting
both the ANC_CHSKM pin and the ANC_CHKSM host
interface bit LOW.
If the chip is receiving ANC EDH flag information through
the flag port or the HOSTIF, then the ANC EDH flag
generated by the ancillary checksum verification block will
be overwritten. However, the additional FF/AP EDH flag will
still appear at the next downstream chip if an illegal
checksum of 3FCH-3FFH was detected and the
ANC_CHKSM function was enabled.
If a checksum error is detected in the EDH packet itself, an
additional separate error flag, EDH_CHKSM is set HIGH in
the HOSTIF read table.
10 of 26
19983 - 1
GS9021A
INCOMING AP CRC
5. Depending on whether one or both of FFV or APV is low,
the Unknown Error Status (UES) flag corresponding to
either FF or AP or both, is set HIGH in the output data.
(No CRC check could be performed, so the data may or
may not contain errors).
3.6 UES Error Flag Updating
3.7 No EDH
PIN
LOGIC OPR
HOST BIT
NO_EDH
Some input data streams may lack the EDH packet. In such
cases, the NO_EDH bit in the HOSTIF read table is
asserted HIGH. If only a few fields lack the EDH packet, the
NO_EDH bit will be asserted only for those fields.
PIN
LOGIC OPR
HOST BIT
ERRORED FIELD COUNTER
CLR[1:0]
ERROR SENSITIVITY BITS
CLR0
MODE OF OPERATION
0
0
Normal
0
1
Reset Counter to Zero
1
0
Auto Reset
1
1
Hold Counter at Zero
reset to zero and begins counting again. The mode of
operation will immediately return to 00 (normal mode) once
the counter resets. In "Auto Reset" mode, the counter
behaves in the normal fashion, except that it resets to zero
every time a HOSTIF read of the lowest 8 bits of the error
counter (address 17) is performed. This functionality allows
the chip to count the number of errors since the last read.
The “Hold Counter at Zero” mode instantly freezes the
counter at zero until it is moved into one of the other modes.
3.9 Flag Port
In determining if the input data stream contains an EDH
packet, the GS9021A looks for two things. First, the
presence of an ANC packet with the header 000 3FF 3FF
1F4 and second, that the ANC header is in the right spot for
the video standard detected. The NO_EDH signal is a
logical NAND of these two cases. If either one is false, the
NO_EDH flag is set.
3.8 Errored Field Counter
CLR1
PIN
LOGIC OPR
HOST BIT
>
OVERWRITE VALUES
F_R/W
S[1:0]
FL[4:0]
In addition to the HOSTIF tables, the EDH error flags can
also be read and written via the synchronous flag port. The
five flag port pins, FL[4:0], allow access to all 15 error flags.
The select pins S[1:0] control which flags are read/written
as outlined below. If the flag port is not going to be used, it
is best to set F_R/W HIGH, leave FL[4:0] unconnected and
set S[1:0] to any value desired but not floating.
3.9.1 Write Mode
The device has a 24 bit ERRORED FIELD COUNTER. The
counter increments by one on the occurrence of one or
more error flags in an OUTGOING EDH packet. The error
flags that can increment the counter are user-selectable
through the 16 ERROR SENSITIVITY bits in the HOSTIF
write table.
The error flag SENSITIVITY bits are active LOW, so that If a
particular sensitivity bit is set LOW, the counter is sensitive
to errors of that type in the OUTGOING EDH packet. The
EDH_CHKSM SENSITIVITY bit is active HIGH.
There are four methods of counter operation. The mode is
set through 2 bits in the HOSTIF write table, denoted CLR1
and CLR0.
In "Normal" mode the counter operates as previously
discussed, such that the counter increments on detection of
any error for which the sensitivity flags are set HIGH. If
“Reset Counter to Zero” mode is selected, the counter is
When the F_R/W pin is LOW, the flag port is in write mode
and the FL[4:0] pins are configured as inputs. After writing
to the flag port, the GS9021A inserts the written flags into
the next outgoing EDH packet. Note that external flag
overwriting via the flag port takes precedence over HOSTIF
overwriting but the flag port write only affects the next
outgoing EDH packet. Following this, if the flag port is not
written to again, flag operation is returned to normal EDH
functionality (unless it is being overwritten through the
HOSTIF).
The data present on the FL[4:0] output pins, as controlled
by the S[1:0] pins, is summarized below.
In addition to overwriting the 15 error flags, the outgoing
validity bits for the active picture (APV) and full field (FFV)
can be overwritten via the flag port.
11 of 26
19983 - 1
GS9021A
In receive mode, a UES flag is set HIGH in the outgoing
EDH packet if the corresponding UES flag was HIGH in the
incoming packet or if the corresponding V bit was LOW.
(For example, if the incoming Active Picture V bit is LOW,
the outgoing Active Picture UES bit will be HIGH). If there is
no EDH packet in the incoming data, all three UES flags
(ANC, AP, FF) are set HIGH.
Write Mode, F_R/W = 0
FL4
FL3
FL2
FL1
FL0
00
FF UES
FF IDA
FF IDH
FF EDA
FF EDH
01
AP UES
AP IDA
AP IDH
AP EDA
AP EDH
10
ANC
UES
ANC
IDA
ANC
IDH
ANC
EDA
ANC
EDH
11
IN/OUT
APV
FFV
0
0
The IN/OUT bit has no effect on writes to the error flags. IN/
OUT is a control bit used to determine if the flags read from
the flag port during flag port read cycles represent
incoming or outgoing EDH flags. If this bit is set HIGH, all
subsequent reads are from the incoming EDH packet. If this
bit is set LOW, then all subsequent reads are from the
updated outgoing packet. When the IN/OUT bit is written to,
the value remains latched until it is reprogrammed. The IN/
OUT bit is set LOW upon reset of the chip.
3.9.2 Read Mode
When the F_R/W pin is HIGH, the flag port is in read mode
and the FL[4:0] pins are configured as outputs. The data
present on the FL[4:0] output pins, as controlled by the
S[1:0] pins, is summarized below.
Read Mode, F_R/W = 1
S[1:0]
FL4
FL3
FL2
FL1
FL0
00
FF UES
FF IDA
FF IDH
FF EDA
FF EDH
01
AP UES
AP IDA
AP IDH
AP EDA
AP EDH
10
ANC UES
ANC
IDA
ANC
IDH
ANC
EDA
ANC
EDH
11
EDH_
CHKSUM
APV
FFV
S
Note that the 15 error flags can be read from the incoming
or outgoing EDH packet (see IN/OUT control bit above).
However, the EDH_CHKSM flag available on pin FL4 when
S[1:0] = 11 is only valid if IN/OUT is LOW. Also, the APV
and FFV bits available on pins FL[3:2] when S[1:0] = 11 are
only valid when IN/OUT is HIGH (that is, the validity bits are
always read from the incoming EDH packet). The S bit is
available regardless of the state of the IN/OUT bit.
3.9.3 Flag Port READ/WRITE Timing
Figure 5a shows a FLAG PORT write cycle followed by a
FLAG PORT read cycle and illustrates the read/write timing
requirements.
A write cycle is initiated by changing the F_R/W signal from
HIGH to LOW.
A delay time, tFDIS, is necessary to change the FL[4:0] pins
from output mode to input mode as defined in the AC timing
table (See Fig.5b). The external controller can begin to
drive the FL[4:0] bus after this delay time. A simple way to
allow for this is to wait one clock cycle before starting to
drive the FL[4:0] port and thus prevent bus contention (but
set the S[1:0] inputs when F_R/W goes LOW so the flags
are not unintentionally affected).
At t5, the F_R/W pin is sampled HIGH, indicating a read
operation. Also at this time, the device reads in the
information on the S[1:0] pins. Upon sampling a read
operation, the device will begin driving the FLAG PORT
after a delay, tFEN, (see Fig. 5c), with invalid data. The
requested information is output on the FL[4:0] pins on the
subsequent clock, t6, plus an output delay time, (see AC
timing table and Fig. 2). That is, there is a one clock latency
between sampling of the S[1:0] pins and when the
corresponding output information is presented on the
FL[4:0] pins. In this example, the S[1:0] pins begin at "00"
and are incremented each clock cycle to read all the error
flags, EDH_CHKSM, validity, and S bits.
The FLAG PORT is synchronous to the clock pin (PCLKIN)
and hence adequate setup and hold times must be
provided as indicated in the AC timing information and Fig.
1. FLAG PORT read/write cycles, relative to the data stream,
should take place as outlined in section 5.3 (HOST
INTERFACE READ/WRITE TIMING)
3.10 CRC_MODE and FLAG_MAP Mode
PIN
LOGIC OPR
HOST BIT
OR
FLAG_MAP
CRC_MODE
FLAG_MAP
A common configuration is to have an input EDH chip that
checks for errors at the input of a piece of equipment,
followed by a processing block that manipulates the data,
followed by an output EDH chip that updates the CRC
values in the EDH packet before the data exits the
equipment. Because the processing block changes the
data values, the CRC values in the EDH packet no longer
represent the data stream. The output EDH chip updates
12 of 26
19983 - 1
GS9021A
S[1:0]
The first time the device samples the F_R/W LOW (at t0) it is
instructed to stop driving the FL[4:0] pins. On each
subsequent rising clock edge (and F_R/W LOW) the device
latches in the data present on S[1:0] and FL[4:0] (at t1, t2, t3
and t4). In this example, the S[1:0] pins begin at "00" and
are incremented each clock cycle to update all the error
flags, validity bits, and the IN/OUT control bit. Note that if a
write cycle is performed to update, say the FF error flags
(S[1:0] = 00), only the FF flags are updated, and the others
are unaffected.
the CRC values to correctly reflect the newly modified data.
To prevent the output EDH chip from indicating erroneous
CRC errors on each field, the GS9021A has two special
modes of operation, CRC_MODE and FLAG_MAP MODE.
3.10.1 CRC_MODE
CRC_MODE is applicable when the processing circuitry
does not corrupt the EDH packet, as illustrated in Figure 6a.
In this configuration, the input EDH chip operates in normal
mode while the output EDH chip is in CRC_MODE. In this
scenario, the input IC receives the EDH packet and does
normal EDH processing. The output IC updates the EDH
packet with new CRC values but passes the EDH flags
through unaltered. Because of this, erroneous EDH flag
handling by the second GS9021A is not performed.
3.10.2 FLAG_MAP Mode
In FLAG_MAP mode, the FLAG PORT is used to read EDH
flags from the GS9021A and write them to another EDH
chip. To enable FLAG_MAP mode, the FLAG_MAP mode
pin and the F_R/W pin must be asserted HIGH (set F_R/W
at least one cycle ahead of FLAG_MAP). After a delay of
tFEN, the FL[4:0] and S[1:0] pins of the FLAG PORT become
outputs and can be connected to the chip which you wish
the GS9021A to write the FLAG data to. In this mode the
GS9021A automatically increments the value of S[1:0] and
subsequently displays the appropriate flags on the FL[4:0]
port, synchronous to the rising edge of PCLKOUT. This is
illustrated in Figure 5d.
Figure 5d displays three properties of the FLAG PORT in
FLAG_MAP mode.
First, each data is present on the FLAG PORT for two clock
cycles to eliminate any setup time violations that might
occur due to clock data skew between chips placed far
apart. However, the designer must still ensure that the hold
time is satisfied. Second, the S[1:0] pins never cycle to the
value of "11" in FLAG_MAP mode since the values
contained in the FL[4:0] register when S[1:0] ="11" are not
considered EDH flags. Also, the chip cycles S[1:0] in the
sequence "01", "00", "10" since this is the order in which the
flags are stored and subsequently decoded from the EDH
For reliable data output on the FLAG PORT, switching the
FLAG_MAP pin when an EDH packet is exiting the device is
not advised. Also, if the EDH core is bypassed by asserting
the BYPASS_EDH pin HIGH, the flag port will always display
zeros. This is because the incoming flags (which will be
decoded and written to the HOSTIF table) will not be updated to reflect the condition of the input data, and as a
result no outgoing flags will be generated (the FLAG PORT
only displays the outgoing EDH flags).
FLAG_MAP mode can be used to write EDH flags to any
chip, the most common use being applicable when the
processing circuitry following the EDH chip corrupts the
EDH packet. In this case, the FLAG_MAP mode can be
used to route the EDH flags from an input EDH chip around
the processing core and write them to an output EDH chip.
In this configuration, the input IC is in FLAG_MAP mode. It
receives the EDH packet, does normal EDH processing and
transfers the new EDH flags to the output IC. The output IC,
which is not in FLAG_MAP mode but is in write mode
(FLAG_MAP and F_R/W stay LOW) receives these flags as
they are written to it by the EDH chip. The output EDH chip
then updates the EDH packet with the new CRC values and
inserts the preserved EDH flags that have been transferred
from the input IC. A diagram of this can be found in Figure
6b.
Because the flags are output as soon as they are decoded,
the maximum processing latency supported between the
two EDH chips is the number of clock cycles in the shortest
field of the standard minus 15 clock cycles.
For example, D1 has one field of 262 x 1716 = 449592
clock cycles, and one field of 263 x 1716 = 451308 clock
cycles. Thus the maximum latency for D1 is 449592 - 15 =
449577 clock cycles.
Any additional latency requires that the flags be delayed
before they can be piped to the output chip. Since writing to
the flag port takes precedence over the HOSTIF writing, if
any of the flags need to be forced at the output EDH chip,
external logic in the routing path must be added.
Alternately, the HOSTIF of the EDH chip can be used to
perform any additional flag masking.
13 of 26
19983 - 1
GS9021A
In CRC_MODE, the CRC values in the EDH packet are
updated by the chip but the error flags are preserved and
unaltered, unless they are overwritten via the HOSTIF or the
FLAG PORT. This mode should be used by the output EDH
chip to prevent the newly processed data from creating
misleading EDH errors due to CRC mismatches. The
CRC_MODE pin takes precedence over the R/T pin in the
GS9021A with respect to the handling of the EDH flags.
Thus when CRC_MODE is HIGH, no flags are set or altered
(unless overwritten by the flags or HOSTIF port) regardless
of the state of the R/T pin. See Table 2 for the effect of the
different settings of R/T and CRC_MODE. The device is
placed in CRC_MODE by asserting the CRC_MODE pin
HIGH.
packet. Finally the S[1:0] pins only change value after
receipt of an EDH packet and are thus static between
packets. During this inter-packet time, the S[1:0] pins
display a value of "01" and the FL[4:0] pins display the ANC
EDH flags from the preceding EDH packet.
3.11 Bypass EDH Processing
PIN
LOGIC OPR
HOST BIT
BYPASS_EDH
OR
BYPASS_EDH
Similarly, if TRS_BLANK is enabled and TRS_INSERT is not,
then there may be 0 TRS per line during a switch. In most
applications, these features should be either both enabled
or both disabled to maintain only two TRSs per line. TRS
blanking will function incorrectly if the flywheel is disabled.
Thus if the flywheel is disabled the TRS_BLANK function
should be disabled as well.
4. DATA PROCESSING BLOCK
The GS9021A contains advanced data processing features
that can simplify system design requirements. These
include:
4.2 ITU-R-601 Clipping
PIN
LOGIC OPR
HOST BIT
601_CLIP
This feature operates on the active picture portion (as
defined in RP165) of the data stream only. When the
601_CLIP bit of the HOSTIF write table is asserted HIGH,
the device remaps all reserved data words in the active
picture to values compliant with ITU-R-601. That is, 000-003
is clipped to 004 and 3FCH -3FFH is clipped to 3FBH.
4.3 Data Blanking
•
TRS Blanking,
•
ITU-R-601 Clipping
•
Data Blanking,
•
TRS Insertion, and
•
ANC Header updating
It is important to note that these processing functions occur
in the GS9021A in the order listed above.
When implementing applications which use the EDH core
(ie. BYPASS_EDH set LOW), TRS blanking, data blanking,
and TRS insertion will indicate a downstream FF/AP EDH
error when a 3FCH-3FFH input data value is blanked out or
overwritten to a value less than 3FBH. As such, users may
wish to disable data blanking, TRS blanking and TRS
insertion by setting the BLANK_EN pin HIGH, the CLIP_TRS
pin LOW, and leaving the corresponding host interface bits
at their power-on default values.
LOGIC OPR
HOST BIT
BLANK_EN
AND
BLANK_EN
Asserting the BLANK_EN pin or the corresponding HOSTIF
write table bit LOW causes the corresponding input data to
be forced to blanking levels. This is a dynamic control
allowing the user to individually select which data words are
to be blanked as shown in Figure 7. TRS and EDH insertion
occurs after data blanking so if all these features are being
used, the output data stream continues to have TRS words
and EDH packets present, even if the BLANK_EN is
constantly held LOW.
The outgoing EDH packet will contain the correct CRC
values for the blanked fields since the CRC values are
calculated and inserted just prior to the data exiting the
device.
The blanking values in hexi-decimal notation for each
standard are as follows:
4.1 TRS Blanking
PIN
PIN
LOGIC OPR
HOST BIT
NTSC/PAL 4:2:2
200 040 200 040 (CB:Y:CR:Y)
NTSC 4ƒsc
0F0
PAL 4ƒsc
100
TRS_BLANK
When asserted HIGH, TRS_BLANK (HOSTIF write table) will
blank out any incorrectly positioned TRS words with respect
to the flywheel. The blanking values used will be
appropriate for the detected video standard as described
below in the Data Blanking section. When TRS_INSERT is
enabled and TRS_BLANK is not, there may be 4 TRSs per
line in the outgoing data stream during a standard switch.
NTSC/PAL 4:4:4:4
040 040 040 040 (B:G:R:A)
200 040 200 040 (CB:Y:CR:A)
14 of 26
19983 - 1
GS9021A
EDH processing can be bypassed by asserting the
BYPASS_EDH pin or HOSTIF write table bit HIGH. When
bypassed, EDH packets pass through the chip unaltered.
Overwriting information in the EDH packet via the HOSTIF
write table or the FLAG PORT has no effect. Data
processing in the chip (as described below) can still occur
even if BYPASS_EDH is asserted. In this case, valid
incoming error flags can be read via the I²C or parallel port
interface. However, reading outgoing error flags via the host
port or the flag port returns values of 0.
These three functions can also be turned on individually
through the HOSTIF as described above. THE CLIP_TRS
pin is logically ORed with each of the three bits from the
HOSTIF table. As a result, as long as the CLIP_TRS pin is
asserted, these functions cannot be turned off via the
HOSTIF.
4.6 Ancillary Header
PIN
LOGIC OPR
4.4 TRS Insertion
PIN
ANC_HEADER
LOGIC OPR
HOST BIT
TRS_INSERT
TRS words, based on the internal flywheel, can be inserted
into the outgoing data stream by asserting HIGH the
TRS_INSERT bit of the HOSTIF write table. Note that for
proper TRS insertion, the incoming standard must be
detected and the flywheel synchronized. That is, the
GS9021A does NOT provide proper TRS insertion for
unformatted video data (video without TRS words).
In the case where the input signal disappears, TRSs will
continue to be inserted based on the last detected
standard. Further, if a TRS is already in the correct location,
it will be overwritten which may have the effect of correcting
the TRSID word.
TRS insertion will function incorrectly if the flywheel is
disabled. Thus if the flywheel is disabled the TRS_INSERT
function should be disabled as well.
PIN
LOGIC OPR
HOST BIT
CLIP_TRS
OR
601_CLIP
TRS_BLANK
TRS_INSERT
Asserting the CLIP_TRS pin HIGH turns on three features
described previously:
2. TRS Blanking, and
3. TRS Insertion
Updating of the ANC headers can occur to facilitate 8-bit to
10-bit conversion. If the ANC_HEADER bit of the HOSTIF
write table is set HIGH, all 3FC-3FF data values
corresponding to component ANC headers are remapped
to 3FF in the output data stream. For example, if 8 bit data
is input to the device, the ANC header of 00, FF, FF will
appear as 000, 3FC, 3FC and will be remapped to 000, 3FF,
3FF by the GS9021A.
5. HOST INTERFACE TABLES
PIN
LOGIC OPR
HOST BIT
HOSTIF_MODE
The HOST INTERFACE TABLES (HOSTIF) refer to memory
locations within the GS9021A which store functional
information about the device. There are two tables, a write
table and read table.
The write table is organized into 15 word locations (each 8
bits wide) as shown in Table 3 and is used to set various
configuration/flag bits. The read table is organized into 23
word locations (each 8 bits wide) as shown in Table 4 and is
used to read status information from the device.
4.5 Clipping And TRS Blanking/Insertion
1. ITU-R-601 Clipping,
HOST BIT
The HOSTIF tables can be accessed via an I²C (InterIntegrated Circuit) serial interface or an 8-bit parallel
interface. The HOSTIF_MODE pin selects which interface is
used. If the HOSTIF_MODE pin is HIGH, the HOSTIF
operates in I²C mode. If the HOSTIF_MODE pin is LOW, the
HOSTIF operates in parallel mode.
Note that many bits stored in the tables are also available
as device pins. Bits in the write table that have a default
value of 0, are logically ORed with the corresponding pin.
Write table control bits VBLANKS/L and BLANK_EN, which
have a default value of 1, are logically ANDed with the
corresponding pin.
15 of 26
19983 - 1
GS9021A
Note that normally the device must first detect the incoming
standard in order for the proper blanking values to be
inserted. However, by setting BLANK_EN low, CLIP_TRS
high and forcing the standard in the HOST write table, the
GS9021A can be used to generate a blank, TRS formatted
video stream (with or without EDH), just by supplying a
clock to the device. The frequency of the clock being
supplied should be less than or equal to the standard
selected. The outgoing stream will just be a frequency
scaled version of that standard.
If the HOST interface is not going to be used, the best way
to set the related pins is as follows:
HOSTIF_MODE = LOW
The asynchronous parallel interface consists of an 8-bit
multiplexed address/data bus (P[7:0]), a chip select pin
(CS), a read/write pin (R/W), and an address/data pin (A/D).
The following should be noted when interfacing to the
parallel port:
CS = HIGH
R/W = HIGH
P[7:0] = N/C
B) Signals are "strobed" into/out of the parallel port on the
falling edge of the CS signal. Setup and hold times, as
defined in the AC timing tables, are relative to this edge
and must be met (see Figure 8a)
5.1 I²C Serial Interface
PIN
LOGIC OPR
HOST BIT
SCL
SDA
A[2:0]
The I²C interface consists of a bi-directional serial data pin
(SDA) and a serial clock input pin (SCL). In addition, 3 input
pins, A[2:0] are provided to assign the chip one of eight
possible I²C addresses (0001A2A1A0).
During an I²C write operation, the first byte written to the
chip (after the device has been addressed) is interpreted
as the starting HOSTIF write table address for the
communication. The next byte is interpreted as data to be
written to the specified address. The address then
automatically increments so that the following bytes are
written to subsequent addresses.
When executing a read operation, a write must be performed first to load the desired starting address. After this,
bytes read from the chip will begin at this address and will
auto-increment. If the read operation is halted and
communication with the chip is later established for another
read, the chip will resume reading at the next HOSTIF
memory address.
In I²C mode, P[7:5] and A/D must be set LOW while R/W
and CS must be set HIGH.
5.2 Parallel Interface
PIN
LOGIC OPR
HOST BIT
C) The GS9021A drives the P[7:0] bus when the R/W pin is
HIGH and the CS pin is LOW. At all other times, the
P[7:0] port is in a high impedance state. The host
interface enable and disable times are shown in Figure
8b and are specified in the AC timing information. In this
figure, the rising/falling edges of R/W and CS are not
aligned to illustrate that the state of the P[7:0] I/Os is
only a combinatorial function of the R/W and CS pins.
A write cycle to the parallel interface is shown in Figure 8c.
The starting address of the operation is written to the chip
by putting the R/W pin LOW (indicating write) and the A/D
pin high (indicating ADDRESS). At t0, the falling edge of CS
strobes in the information. Following this, the A/D line
should be asserted LOW indicating data. The R/W line
remains LOW indicating a write operation and at t1 the data
is strobed into the device.
A read example follows the write cycle. Note that the read
cycle begins with a write operation to indicate the starting
address. At t2, R/W is LOW (indicating write), A/D is HIGH
(indicating address) and P[7:0] represent the starting
address for the read cycle. After sufficient hold time, the
microcontroller releases the P[7:0] bus and the R/W is
asserted HIGH to indicate a read operation. At t3, the CS is
asserted low causing the GS9021A to present the required
data on the P[7:0] bus.
If two consecutive data read/write operations are
performed, the device will automatically increment the
address. However, for a completely random-access
operation, the address can be specified prior to every data
read/write operation.
P[7:0]
A/D
R/W
CS
16 of 26
19983 - 1
GS9021A
A) Read/Write cycles via the parallel interface are
completely independent and asynchronous to the
parallel clock PCLKIN.
A/D = DON'T CARE (BUT NOT FLOATING)
5.3 Host Interface Read/Write Timing
Figure 9 illustrates valid times for reading/writing information
from the HOSTIF tables. Figure 9 represents two fields of
video data entering and exiting the GS9021A. The relative
position of the EDH packet in the data stream is also shown.
(Note that the EDH packet entering the device at t0, EDH
F0, represents the EDH information from the previous field,
FIELD 0).
It is safe to read or write EDH information at least two lines
after an EDH packet exits the chip but before the
subsequent EDH packet enters the chip. Reading during
the time interval shown will show values from EDH F0.
Writing during the time interval shown will affect EDH F1.
In applications where a board-level reset is not available, a
circuit similar to figure 10b can be used to ensure correct
reset on power-up. The RESET pin will typically take 1.4ms
to reach 2.5V on power up, but can take longer for power
supplies with slower rise times. A bleed resistor such as
the one shown (20k) will assist the capacitor to discharge
once power is removed. The user should allow the
capacitor to discharge to at least 0.5V before power is
reapplied, to permit a full internal reset. The time taken by
the RESET pin to reach 0.5V on power down, is dependent
upon the fall time of the power supply.
Note that the above read/write timing should also be
observed when reading/writing flag information via the
FLAG PORT.
6.0 RESET
PIN
LOGIC OPR
HOST BIT
RESET
Setting the RESET input pin LOW re-initializes the internal
control circuitry including returning all HOST interface
programming values to their original default values. The
data pipe is not affected by the reset, so data continues to
tH
SYNCHRONOUS
INPUTS
tS
PCLKIN
Fig. 1 Input Setup & Hold Times (Synchronous Inputs)
SYNCHRONOUS
OUTPUTS
DATA
VALID
tOS
tOH
PCLKIN
tOD
Fig. 2 Output Delay & Hold Times (Synchronous Outputs)
17 of 26
19983 - 1
GS9021A
flow through the chip unprocessed during resetting. An
internal power-on-reset cell is also present in the device so
that device initialization occurs on power-up. Figure 10a
illustrates the reset circuitry. The internal power-on reset
circuit of the GS9021A is sensitive to the rise time of the
power supply, hence an external power on reset chip or
board level reset line is strongly recommended.
When
using this technique, the user must ensure that a minimum
pulse width of 100ns is present on the reset line.
TABLE 2: GS9021A Case Table
MODE
TX MODE
RX MODE
R/T
CRC_MODE
EDH
PACKET
1
0
0
NO
2
0
0
YES
3
X
1
4
X
5
6
RESULTS
COMMENTS / SUGGESTIONS
No EDH comparison is performed.
A new EDH packet is inserted into
the data stream with all the EDH
flags cleared unless overwritten by
the dedicated flag port or the host
interface. The EDH packet will
include CRC values calculated
from the data stream.
Use this MODE if you wish to
insert EDH if it is not present. If
EDH is present, clear all flags and
update CRC.
NO
Same results as Case #1
1
YES
No EDH comparison is performed
(i.e. no attempt is made to detect
errors). The CRC is updated and
all flags preserved or unaltered
unless overwritten by the
dedicated flag port or host
interface.
Use this MODE on the output EDH
chip when mapping flags from an
input EDH chip around a
processing core (which would
alter the picture data) to an output
EDH chip so that EDH errors are
not generated. You can also use
this mode when you simply want
to update the CRC values after
processing, if the processing
does not corrupt the EDH packet.
In both cases, the EDH flags are
preserved.
1
0
NO
New EDH packet inserted into
data stream with all error flags
cleared and all UES flags set high
unless overwritten by the
dedicated flag port or the host
interface.
Use this MODE when you wish to
detect errors in the data stream,
or on an input EDH chip when
mapping flags around a
processing core (that would alter
the picture data) to an output EDH
chip so that EDH errors are not
generated due to the data
processing.
1
0
YES
EDH comparison performed and
error flags set and mapped
appropriately unless overwritten
by the dedicated flag port or the
host interface. The CRC is
updated and the EDH packet is reinserted.
Use this MODE when you want to
insert EDH if it is not present or
update CRC values and preserve
the flags in an existing EDH
packet.
NOTE
1. “X” in the table above means ‘don’t care’ (but not left floating).
DIN [9:0]
1
2
3
4
5
6
7
8
1
DOUT [9:0]
2
3
tLAT
PCLK IN
Fig. 3 Data Latency through the GS9021A
18 of 26
19983 - 1
GS9021A
CRC MODE
CASE
NUMBER
0
0
0
0
0
11
12
13
14
15
0
0
9
10
0
0
7
8
0
6
0
5
RW7 B3
RW6 B5
RW5 B7
RW3 B3
RW2 B5
RW1 B7
AP UES
FF UES
AP UES
FF UES
AP UES
FF UES
601_CLIP
0
0
0
0
0
0
0
0
0
0
0
0
1
1
0
6
RW7 B2
RW6 B4
RW5 B6
RW3 B2
RW2 B4
RW1 B6
AP IDA
FF IDA
AP IDA
FF IDA
AP IDA
FF IDA
BLANK_EN
VBLANKS/L
STICKY OUT
NOTE: 1. Superscripts denote default settings upon reset.
RESERVED
(OUTGOING)
ERROR
SENSITIVITY BITS
OVERWRITE
CONTROL
0
3
4
0
2
OVERWRITE
VALUES
0
1
CONFIGURATION
7
STICKY IN
0
ADDRESS
WRITE Table
TABLE 3: GS9021A Host Interface Write Table
0
0
0
0
0
0
0
0
0
0
RO_CTRL
RW6 B3
RW5 B5
RW4 B7
RW2 B3
RW1 B5
AP IDH
FF IDH
AP IDH
FF IDH
1
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
ANC_HEADER
STD SEL
CLR1
1
0
0
0
5
FFV
RW6 B2
RW5 B4
RW4 B6
RW2 B2
RW1 B4
AP EDA
FF EDA
AP EDA
FF EDA
AP EDA
FF EDA
BYPASS_EDH
S
CLR0
4
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
APV
RW7 B7
RW5 B3
RW4 B5
RW3 B7
RW1 B3
AP EDH
FF EDH
AP EDH
FF EDH
AP EDH
FF EDH
FLAG_MAP
STD3
SWITCH FLYW
3
RW7 B6
RW5 B2
RW4 B4
RW3 B6
RW1 B2
ANC EDA
ANC UES
ANC EDA
ANC UES
AND EDA
ANC UES
ANC_CHKSM
STD2
FLYWDIS
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
2
RW7 B5
RW6 B7
RW4 B3
RW3 B5
RW2 B7
ANC EDH
ANC IDA
ANC EDH
ANC IDA
ANC EDH
ANC IDA
TRS_INSERT
STD1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
GS9021A
19 of 26
19983 - 1
TRS_BLANK
STD0
ANC IDH
RW7 B4
RW6 B6
RW4 B2
RW3 B4
RW2 B6
EDH_CHKSM
ANC IDH
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
0
RESERVED
WORDS
(INCOMING)
ERRORED FIELD
COUNTER
AP CRC
OUTGOING
AP CRC
INCOMING
FF CRC
OUTGOING
FF CRC
INCOMING
OUTGOING
ERROR FLAGS
b23
b15
b7
RW1 B7
RW2 B5
RW3 B3
RW5 B7
RW6 B5
RW7 B3
16
17
18
19
20
21
22
23
b7
b15
b7
b15
b7
b15
b7
b15
15
14
13
12
11
10
9
8
7
AP UES
6
AP UES
4
FF UES
FF UES
3
5
NO_EDH
2
INCOMING
ERROR FLAGS
F2
1
CONFIGURATION
7
ADDRESS
READ Table
TABLE 4: GS9021A Host Interface Read Table
RW7 B2
RW6 B4
RW5 B6
RW3 B2
RW2 B4
RW1 B6
b6
b14
b22
b6
b14
b6
b14
b6
b14
b6
b14
AP IDA
FF IDA
AP IDA
FF IDA
EDH_CHKSM
F1
6
0
RW6 B3
RW5 B5
RW4 B7
RW2 B3
RW1 B5
b5
b13
b21
b5
b13
b5
b13
b5
b13
b5
b13
AP IDH
FF IDH
AP IDH
FF IDH
TRS_ERR
F0
5
0
RW6 B2
RW5 B4
RW4 B6
RW2 B2
RW1 B4
b4
b12
b20
b4
b12
b4
b12
b4
b12
b4
b12
AP EDA
FF EDA
AP EDA
FF EDA
FFV
S
4
0
RW7 B7
RW5 B3
RW4 B5
RW3 B7
RW1 B3
b3
b11
b19
b3
b11
b3
b11
b3
b11
b3
b11
AP EDH
FF EDH
AP EDH
FF EDH
APV
STD3
3
0
RW7 B6
RW5 B2
RW4 B4
RW3 B6
RW1 B2
b2
b10
b18
b2
b10
b2
b10
b2
b10
b2
b10
ANC EDA
ANC UES
ANC EDA
ANC UES
0
STD2
2
0
RW7 B5
RW6 B7
RW4 B3
RW3 B5
RW2 B7
b1
b9
b17
b1
b9
b1
b9
b1
b9
b1
b9
ANC EDH
ANC IDA
ANC EDH
ANC IDA
0
STD1
1
GS9021A
20 of 26
19983 - 1
0
RW7 B4
RW6 B6
RW4 B2
RW3 B4
RW2 B6
b0
b8
b16
b0
b8
b0
b8
b0
b8
b0
b8
0
ANC IDH
0
ANC IDH
0
STD0
0
tOD tOS
tOS tOH
CLOCK
3FF
000
000
3FF
EAV
000
000
GS9021A
DOUT [9:0]
SAV
F [2:0]
V
H
Fig. 4a FVH Timing for Component Video
tOD tOS
tOH tOS
CLOCK
DOUT [9:0]
3FF
000
000
000
TRS-ID
F [2:0]
H
Fig. 4b F and H Timing for Composite Video
READ CYCLE
{
{
WRITE CYCLE
F_R//W
FL[4:0]
XX
FF
AP
ANC
XX
t0
t1
t2
t3
t4
t5
t6
t7
t8
XX
00
01
10
11
00
01
10
11
S11
FF
AP
ANC
S11
PCLKIN
S[1:0]
Fig. 5a Flag Port Read/Write Timing
21 of 26
19983 - 1
F_R/W
F_R/W
tFEN
FL [4:0]
FL [4:0]
tFDIS
PCLKIN
GS9021A
PCLKIN
Fig. 5c Flag Port Enable Time
Fig. 5b Flag Port Disable Time
PCLKIN
F_R/W
X
FLAGMAP
FL[4:0]
XX0 XX1 XX 2
AP
FF
ANC
ANC
AP
FF
ANC
S[1:0]
XX 0 XX 1 XX 2
01
00
10
10
01
00
10
t
Flags held at ANC between EDH packets
FEN
Double clocking
Fig. 5d Flag Port Timing in FLAG_MAP Mode
GS9020A
or
GS9021A
CRC_MODE = 0
R/T = 1 (GS9021A)
GS9021A
PROCESSING
WHICH DOES NOT
AFFECT THE
EDH PACKET
CRC_MODE = 1
Fig. 6a Example of CRC_MODE Implementation
GS9020A
or
GS9021A
CRC_MODE = 0
FLAG MAP = 1
F_R/W = 1
R/T = 1 (GS9021A)
GS9021A
PROCESSING
CORRUPTS
EDH PACKET
FL [4:0]
S [1:0]
FLAG MAP = 0
F_R/W = 0
7
Fig. 6b Example of FLAG_MAP Mode Implementation
22 of 26
19983 - 1
DIN[9:0]
1
2
3
4
5
6
7
8
9
10
BLANKED SAMPLES
{
DOUT[9:0]
1
2
9
10
GS9021A
BLANK_EN
Fig. 7 Illustration of Data Blanking
tHS
tHH
P [7:0]
A/D
R/W
CS
Fig. 8a HOSTIF Parallel Port Input Setup & Hold Times
tHEN
P[7:0]
tHDIS
GS9021A DRIVING
R/W
CS
Fig. 8b HOSTIF Parallel Port Output Enable and Disable Times
READ CYCLE
{
{
WRITE CYCLE
P[7:0]
ADDRESS
DATA IN
ADDRESS
DATA
DATA
R/W
A/D
CS
t0
t1
t2
t3
t4
Fig. 8c HOSTIF Parallel Port Read/Write Cycles
23 of 26
19983 - 1
FIELD 0
DIN[9:0]
FIELD 1
FIELD 2
E
D
H
F1
E
D
H
F0
t0
GS9021A
E
D
H
F1
E
D
H
F0
DOUT[9:0]
2 LINES
VALID TIME TO READ/WRITE
EDH INFORMATION TO/FROM GS9021A
Fig. 9 Host Interface Read/Write Timing
tMAX = 25µs
INTERNAL
POWER on
RESET CELL
INTERNAL
RESET
SIGNAL
RESET
PIN
tRESET
Fig. 10a Reset Circuitry
~1.4 mS
VDD
VDD
5V
2k
0V
t
RESET
RESET
Manual
Reset
Switch
(Optional)
5V
1uF
20k
0V
t
Fig. 10b Acceptable external reset circuit when a master reset is not available
24 of 26
19983 - 1
VIDEO DATA & CLOCK INPUT
PCLK
DIN0
DIN1
DIN2
DIN3
DIN4
DIN5
DIN6
DIN7
DIN8
100nF
C161 VDD
I2C INTERFACE
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
64
A0
A1
A2
SDA
SCL
P5
P6
P7
PCLKIN
DIN0
DIN1
DIN2
GND
VDD
DIN3
DIN4
DIN5
DIN6
DIN7
DIN8
DIN9
CLIP_TRS
17 SCL/P4
DIN9
FLYWDIS
FLYWDIS
63
18 SDA/P3
CLIP_TRS
BLANK_EN
62
19 A2/P2
BLANK_EN
LSB_TOP
61
20 A1/P1
60
BYPASS_EDH
21 A0/P0
BYPASS_EDH
VDD
100nF
GS9021A
VDD
23 A/D
VDD
100nF
C176
VDD
FVH INDICATION
See Figure 10b
11
36
RTERMINATION
10
37
33
34
35
9
38
7
6
5
8
100nF
C166
VDD
4
3
2
1
39
40
41
42
43
44
45
46
47
48
FLAG PORT I/O
FL3
FL4
F_R/W
FLAG_MAP
DO0
DO1
D02
GND
VDD
D3
D4
D5
D6
D7
D8
D9
VDD
100nF
C176
PCLK
PD0
PD1
PD2
PD3
PD4
PD5
PD6
PD7
PD8
PD9
USERSELECTABLE
43
R/T
24 CS
59
VBLANKS/L
22 R/W
58
CRC_MODE
57
VDD
56
GND
25 HOSTIF_MODE
55
R/T
26 VDD
54
RESET
27 GND
53
FIELD2
28 S0
52
FIELD1
29 S1
GS9032
VDD
100nF
C179
373
R198
36
VBLANKS/L
31 FL1
51
FIELD0
30 FL0
50
HBLANK
49
VBLANK
32 FL2
41
LF-
44
SYNC DIS
VEE
12
VEE
VCC
13
42
LF+
NC(COSC)
14
SS2
15
USERSELECTABLE
40
LBWC
39
VCC
17
VEE
18
SS1
16
VEE
38
RVCO
37
NC(CBG)
35
VDD
100nF
C180
Q10
R202
75
LED70
54R9
R200
RESET 33
32
A/M
31
BYPASS_EN
30
AMP1
29
VEE
28
SDO1
27
SDO1
26
VEE
25
SDO0
24
SDO0
23
VEE
20
R25
SD1_EN
19
RVCO+
21
SS0
1k
LOCK
VEE
34
VCC
AMP0
22
USER SELECTED
SETTINGS
220
R201
C181
100nF
VDD
VDD
R203
75
VDD
GS9021A
Fig. 11 GS9021A - GS9032 Application Circuit
25 of 26
19983 - 1
C184
L16 8.2nH
1µF
1µF
L15 8.2nH
R205
75
C183
R204
75
J7
J6
PACKAGE DIMENSIONS
16.00 BSC
14.00 BSC
64
0.20 MIN
0.08/0.20 RADIUS
16.00 BSC
14.00 BSC
GS9021A
12 ±1
1
7 MAX
0 MIN
12 ±1
0.60
±0.15
0.08 MIN
RADIUS
1.0
REF
All dimensions in millimetres
1.40 ±0.05
64 pin LQFP
1.60 MAX
0.80 BSC
0.37 ±0.08
CAUTION
ELECTROSTATIC
SENSITIVE DEVICES
DO NOT OPEN PACKAGES OR HANDLE
EXCEPT AT A STATIC-FREE WORKSTATION
DOCUMENT IDENTIFICATION
REVISION NOTES:
DATA SHEET
The product is in production. Gennum reserves the right to make
changes at any time to improve reliability, function or design, in order to
provide the best product possible.
Modified ordering information.
GENNUM CORPORATION
MAILING ADDRESS:
P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3
Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946
SHIPPING ADDRESS:
970 Fraser Drive, Burlington, Ontario, Canada L7L 5P5
GENNUM JAPAN CORPORATION
Shinjuku Green Tower Building 27F, 6-14-1, Nishi Shinjuku,
Shinjuku-ku, Tokyo, 160-0023 Japan
Tel. +81 (03) 3349-5501, Fax. +81 (03) 3349-5505
GENNUM UK lIMITED
25 Long Garden Walk, Farnham, Surrey, England GU9 7HX
Tel. +44 (0)1252 747 000 Fax +44 (0)1252 726 523
Gennum Corporation assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement.
© Copyright September 2001 Gennum Corporation. All rights reserved. Printed in Canada.
26 of 26
19983 - 1
Similar pages