Maxim MAX9094 General-purpose, low-voltage, dual/quad, tiny pack comparator Datasheet

19-6350; Rev 0; 7/12
EVALUATION KIT AVAILABLE
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
General Description
The MAX9092/MAX9093/MAX9094/MAX9095 comparators are pin-for-pin compatible replacements for the
LMX393/LMX393H/LMX339/LMX339H, respectively. The
MAX9093/MAX9095 have the added benefit of internal
hysteresis to provide noise immunity, preventing output
oscillations even with slow-moving input signals.
Advantages of the ICs include low supply voltage, small
package, and low cost. They also offer a wide supply
voltage range, wide operating temperature range, competitive CMRR and PSRR, response time characteristics,
input offset, low noise, output saturation voltage, input
bias current, and RF immunity.
The ICs are available in both 8-pin SOT23/µMAXM and
14-pin TSSOP/SO packages.
Applications
Features
S Guaranteed +1.8V to +5.5V Performance
S -40NC to +125NC Automotive Temperature Range
S Low Supply Current (65µA/Channel at
VDD = +5.0V)
S Input Common-Mode Voltage Range Includes
Ground
S No Phase Reversal for Overdriven Inputs
S Low Output Saturation Voltage (120mV)
S Internal 2mV Hysteresis (MAX9093/MAX9095)
S Fast 100ns Propagation Delay
S Open-Drain Outputs
S 8-Pin SOT23/µMAX and 14-Pin TSSOP/SO
Packages
Mobile Communications
Notebooks and PDAs
Automotive
Battery-Powered Electronics
Ordering Information appears at end of data sheet.
General-Purpose Portable Devices
General-Purpose Low-Voltage Applications
For related parts and recommended products to use with this part,
refer to www.maxim-ic.com/MAX9092.related.
µMAX is a registered trademark of Maxim Integrated Products, Inc.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (VDD to VSS)...................................-0.3V to +6V
All Other Pins except OUT_........... (VSS - 0.3V) to (VDD + 0.3V)
OUT_..................................................................(VSS - 0.3) to 6V
Continuous Power Dissipation (Multilayer Board)(TA = +70NC)
SOT23 (derate 5.1mW/°C above +70°C).................408.2mW
µMAX (derate 4.8mW/°C above +70°C)...................387.8mW
TSSOP (derate 10mW/°C above +70°C).....................796mW
SO (derate 11.9mW/°C above +70°C)........................952mW
Operating Temperature Range......................... -40NC to +125NC
Junction Temperature......................................................+150NC
Storage Temperature Range............................. -65NC to +150NC
Lead Temperature (soldering, 10s).................................+300NC
Soldering Temperature (reflow).......................................+260NC
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
SOT23
Junction-to-Ambient Thermal Resistance (qJA).........196°C/W
Junction-to-Case Thermal Resistance (qJC)................70°C/W
µMAX
Junction-to-Ambient Thermal Resistance (qJA)......206.3°C/W
Junction-to-Case Thermal Resistance (qJC)................42°C/W
TSSOP
Junction-to-Ambient Thermal Resistance (qJA)......100.4°C/W
Junction-to-Case Thermal Resistance (qJC)................30°C/W
SO
Junction-to-Ambient Thermal Resistance (qJA)...........84°C/W
Junction-to-Case Thermal Resistance (qJC)................34°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
DC ELECTRICAL CHARACTERISTICS—2.7V OPERATION
(VDD = 2.7V, VSS = 0V, VCM = 0V, RL = 5.1kI connected to VDD, typical values are at TA = +25NC, unless otherwise noted. Boldface
limits apply at the defined temperature extremes.) (Note 2)
PARAMETER
Input Offset Voltage
SYMBOL
CONDITIONS
MIN
VOS
Input Voltage Hysteresis
VHYST
Input Offset Voltage Average
Temperature Drift
TCVOS
MAX9093/MAX9095
TA = +25NC
Input Bias Current
IB
Input Voltage Range
Voltage Gain
Output Saturation Voltage
Output Sink Current
Supply Current
IOS
VSAT
IO
IS
mV
2
mV
1.5
FV/NC
Q250
±400
TA = -40NC to +125NC
±400
Q0.0003
nA
±50
TA = -40NC to +85NC
±150
TA = -40NC to +125NC
±150
-0.1
nA
V
2
MAX9092/MAX9095
50
V/mV
ISINK P 1mA
25
mV
VO P 1.5V
5
16
mA
MAX9092/MAX9093 (both comparators)
100
180
MAX9094/MAX9095 (all four comparators)
220
360
TA = +25NC
Output Leakage Current
UNITS
7
TA = -40NC to +85NC
VCM
AV
MAX
0.4
Q0.0003
TA = +25NC
Input Offset Current
TYP
FA
0.005
TA = -40NC to +85NC
1
TA = -40NC to +125NC
2
FA
2
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
AC ELECTRICAL CHARACTERISTICS—2.7V OPERATION
(VDD = 2.7V, VSS = 0V, VCM = 0V, RL = 5.1kI connected to VDD, typical values are at TA = +25NC, unless otherwise noted. Boldface
limits apply at the defined temperature extremes.) (Note 2)
PARAMETER
SYMBOL
Propagation Delay Output
High to Low (Note 3)
tPHL
Propagation Delay Output
Low to High (Note 3)
tPLH
CONDITIONS
MIN
TYP
Input overdrive = 10mV
70
Input overdrive = 100mV
50
Input overdrive = 10mV
115
Input overdrive = 100mV
100
MAX
UNITS
ns
ns
DC ELECTRICAL CHARACTERISTICS–5.0V OPERATION
(VDD = 5V, VSS = 0V, VCM = 0V, RL = 5.1kI connected to VDD, typical values are at TA = +25NC, unless otherwise noted. Boldface
limits apply at the defined temperature extremes.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TA = +25NC
Input Offset Voltage
VOS
TYP
MAX
0.4
7
TA = -40NC to +85NC
9
TA = -40NC to +125NC
Input Voltage Hysteresis
Input Offset Voltage Average
Temperature Drift
TCVOS
IB
IOS
Input Voltage Range
VCM
Voltage Gain (Note 4)
AV
Output Sink Current
VSAT
IO
IS
FV/NC
Q250
±400
±400
±0.007
±150
TA = -40NC to +125NC
±150
-0.1
20
ISINK P 4mA
50
120
V/mV
400
TA = -40NC to +85NC
700
TA = -40NC to +125NC
700
10
VO P 1.5V
TA = +25NC
35
130
mA
250
TA = -40NC to +125NC
300
250
mV
200
TA = -40NC to +85NC
TA = +25NC
MAX9094/
MAX9095 (all four TA = -40NC to +85NC
comparators)
TA = -40NC to +125NC
nA
V
4.2
MAX9092/MAX9094
nA
±50
TA = -40NC to +85NC
TA = +25NC
Output Leakage Current
1.5
TA = -40NC to +125NC
MAX9092/
MAX9093 (both
comparators)
Supply Current (Note 5)
mV
TA = -40NC to +85NC
TA = +25NC
Output Saturation Voltage
2
Q0.027
TA = +25NC
Input Offset Current
mV
9
MAX9093/MAX9095
TA = +25NC
Input Bias Current
UNITS
FA
400
500
FA
500
0.005
TA = -40NC to +85NC
1
TA = -40NC to +125NC
2
FA
3
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
AC ELECTRICAL CHARACTERISTICS–5.0V OPERATION
(VDD = 5V, VSS = 0V, VCM = 0V, RL = 5.1kI connected to VDD, typical values are at TA = +25NC, unless otherwise noted. Boldface
limits apply at the defined temperature extremes.) (Note 2)
PARAMETER
SYMBOL
Propagation Delay Output
High to Low (Note 3)
tPHL
Propagation Delay Output
Low to High (Note 3)
tPLH
CONDITIONS
MIN
TYP
Input overdrive = 10mV
70
Input overdrive = 100mV
50
Input overdrive = 10mV
110
Input overdrive = 100mV
100
MAX
UNITS
ns
ns
DC ELECTRICAL CHARACTERISTICS—1.8V OPERATION
(VDD = 1.8V, VSS = 0V, VCM = 0V, RL = 5.1kI connected to VDD, typical values are at TA = +25NC, unless otherwise noted. Boldface
limits apply at the defined temperature extremes.) (Note 2)
PARAMETER
Input Offset Voltage
SYMBOL
Input Voltage Hysteresis
Input Offset Voltage Average
Temperature Drift
Input Bias Current
Input Offset Current
Input Voltage Range
CONDITIONS
MAX9093/MAX9095
TYP
MAX
UNITS
0.4
5
mV
2
mV
TCVOS
1.5
FV/NC
IB
0.0016
nA
IOS
0.0003
nA
-0.1
VCM
VSAT
ISINK P 1mA
Power-Supply Rejection Ratio
PSRR
VDD = 1.8V to 5.5V
Output Sink Current
IOUT
IS
V
1
Output Saturation Voltage
Supply Current (Note 5)
MIN
VOS
56
mV
90
dB
VOUT P 1.5V
6.4
mA
MAX9092/MAX9093 (both comparators)
120
170
MAX9094/MAX9095 (all four comparators)
210
340
60
Output Leakage Current
0.001
FA
FA
AC ELECTRICAL CHARACTERISTICS—1.8V OPERATION
(VDD = 1.8V, VSS = 0V, VCM = 0V, RL = 5.1kI connected to VDD, typical values are at TA = +25NC, unless otherwise noted. Boldface
limits apply at the defined temperature extremes.) (Note 2)
PARAMETER
SYMBOL
Propagation Delay Output
High to Low (Note 3)
tPHL
Propagation Delay Output
Low to High (Note 3)
tPLH
Note
Note
Note
Note
2:
3:
4:
5:
CONDITIONS
MIN
TYP
Input overdrive = 10mV
70
Input overdrive = 100mV
60
Input overdrive = 10mV
120
Input overdrive = 100mV
110
MAX
UNITS
ns
ns
All devices are production tested at TA = +25NC, unless otherwise noted. All temperature limits are guaranteed by design.
Input overdrive is the overdrive voltage beyond the offset and hysteresis-determined trip points.
Guaranteed by design.
Supply current when output is high.
4
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Typical Operating Characteristics
(VDD = 5V, VSS = 0V, VCM = 0V, RL = 5.1kI, CL = 10pF, overdrive = 100mV, TA = +25NC, unless otherwise noted.)
SUPPLY CURRENT vs. SUPPLY VOLTAGE
50
TA = +25°C
40
TA = -40°C
30
20
10
50
40
TA = +25°C
30
TA = -40°C
20
VOUT = LOW
0
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
SUPPLY VOLTAGE (V)
SUPPLY CURRENT vs. FREQUENCY
(VOVERDRIVE = 10mV)
INPUT OFFSET VOLTAGE
vs. TEMPERATURE
VDD = 5V
120
100
80
VDD = 2.7V
VDD = 1.8V
60
40
0.35
VDD = 1.8V
0.30
INPUT OFFSET VOLTAGE (mV)
MAX9092 toc03
SUPPLY VOLTAGE (V)
140
20
0.25
VDD = 5V
VDD = 2.7V
0.20
0.15
0.10
0.05
0
10
100
1k
10k
100k
0
25
50
75
100
INPUT BIAS CURRENT
vs. TEMPERATURE
OUTPUT VOLTAGE LOW
vs. PULLUP RESISTANCE
MAX9092 toc05
VDD = 5V
0.1
0.01
0.001
VDD = 1.8V
0.00001
0
25
50
300
VOL - VEE
250
125
200
150
100
50
VDD = 2.7V
-25
-25
TEMPERATURE (°C)
1
-50
-50
INPUT FREQUENCY (Hz)
10
0.0001
0
1M
OUTPUT VOLTAGE LOW (mV)
1
MAX9092 toc06
SUPPLY CURRENT (µA)
60
10
VOUT = HIGH
0
INPUT BIAS CURRENT (nA)
TA = +85°C
TA = +125°C
MAX9092 toc04
60
70
SUPPLY CURRENT (µA)
SUPPLY CURRENT (µA)
TA = +125°C
MAX9092 toc02
TA = +85°C
70
SUPPLY CURRENT vs. SUPPLY VOLTAGE
80
MAX9092 toc01
80
75
TEMPERATURE (°C)
100
125
0
0.1
1
10
100
PULLUP RESISTANCE (kI)
5
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Typical Operating Characteristics (continued)
(VDD = 5V, VSS = 0V, VCM = 0V, RL = 5.1kI, CL = 10pF, overdrive = 100mV, TA = +25NC, unless otherwise noted.)
PROPAGATION DELAY vs. TEMPERATURE
(VOVERDRIVE = 100mV)
PROPAGATION DELAY vs. CAPACITIVE LOAD
(VOVERDRIVE = 100mV)
500
tPLH
400
300
200
tPHL
80
60
tPHL
40
0
0
20
40
60
80
100
-25
0
25
50
75
100
TEMPERATURE (°C)
PROPAGATION DELAY
vs. INPUT OVERDRIVE (tPLH)
PROPAGATION DELAY
vs. INPUT OVERDRIVE (tPHL)
80
70
TA = +125°C
TA = +85°C
50
90
PROPAGATION DELAY (ns)
TA = -40°C
TA = +25°C
40
30
TA = +125°C
80
TA = +85°C
70
60
TA = +25°C
50
TA = -40°C
40
30
20
20
10
10
0
125
100
MAX9092 toc09
100
60
-50
CAPACITIVE LOAD (pF)
110
90
120
MAX9092 toc10
0
PROPAGATION DELAY (ns)
tPLH
20
100
0
0
200
400
600
800
1000
1200
0
200
400
600
800
INPUT OVERDRIVE (mV)
INPUT OVERDRIVE (mV)
INPUT HYSTERESIS VOLTAGE
vs. TEMPERATURE
PROPAGATION DELAY
100mV OVERDRIVE
1000
1200
MAX9092 toc12
MAX9092 toc11
3.0
INPUT HYSTERESIS VOLTAGE (mV)
MAX9092 toc08
100
PROPAGATION DLEAY (ns)
600
PROPAGATION DELAY (ns)
120
MAX9092 toc07
700
2.5
VIN
VDD = 5V
2.0
1.5
VDD = 1.8V
1.0
VDD = 2.7V
0.5
VOUT
0
-50
0
50
100
150
1µs/div
TEMPERATURE (°C)
6
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Typical Operating Characteristics (continued)
(VDD = 5V, VSS = 0V, VCM = 0V, RL = 5.1kI, CL = 10pF, overdrive = 100mV, TA = +25NC, unless otherwise noted.)
PROPAGATION DELAY
(10mV OVERDRIVE)
250kHz RESPONSE
(100mV OVERDRIVE)
MAX9092 toc13
MAX9092 toc14
VIN
VIN
VOUT
VOUT
400ns/div
1µs/div
250kHz RESPONSE
(10mV OVERDRIVE)
100kHz RESPONSE
(100mV OVERDRIVE)
MAX9092 toc15
VIN
MAX9092 toc16
VIN
VOUT
VOUT
400ns/div
2µs/div
100kHz RESPONSE
(10mV OVERDRIVE)
POWER-UP RESPONSE
MAX9092 toc18
MAX9092 toc17
VIN+
200mV/div
VIN
VDD
2V/div
VOUT
2V/div
VOUT
2µs/div
4µs/div
7
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Pin Configurations
TOP VIEW
OUTB 1
OUTA
1
INA-
2
INA+
VSS
+
+
MAX9094/MAX9095
OUTA 2
MAX9092/MAX9093
A
3
8
VDD
VDD 3
7
OUTB
INA- 4
INB-
INA+ 5
INB+
INB- 6
6
B
4
5
INB+ 7
SOT23/µMAX
14 OUTC
13 OUTD
12 VSS
A
D
B
C
11 IND+
10 IND9
INC+
8
INC-
TSSOP/SO
Pin Description
PIN
NAME
FUNCTION
MAX9092/MAX9093
MAX9094/MAX9095
1
2
OUTA
2
4
INA-
Comparator A Inverting Input
3
5
INA+
Comparator A Noninverting Input
4
12
VSS
5
7
INB+
Comparator B Noninverting Input
6
6
INB-
Comparator B Inverting Input
7
1
OUTB
Comparator A Output (Open Drain)
Negative Supply (Connect to Ground)
Comparator B Output (Open Drain)
8
3
VDD
Positive Supply
—
8
INC-
Comparator C Inverting Input
—
9
INC+
Comparator C Noninverting Input
—
10
IND-
Comparator D Inverting Input
—
11
IND+
Comparator D Noninverting Input
—
13
OUTD
Comparator D Output (Open Drain)
—
14
OUTC
Comparator C Output (Open Drain)
8
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Detailed Description
The MAX9092/MAX9093/MAX9094/MAX9095 are lowcost, general-purpose comparators that have a singlesupply +1.8V to +5V operating voltage range. The
common-mode input range extends from -0.1V below the
negative supply to within +0.8V of the positive supply.
They require approximately 65FA per comparator with a
5V supply and 50FA with a 2.7V supply.
The MAX9093/MAX9095 have 2mV of hysteresis for noise
immunity. This significantly reduces the chance of output
oscillations even with slow moving input signals. The ICs
are ideal for automotive applications because they operate from -40NC to +125NC. See the Typical Operating
Characteristics.
Applications Information
Hysteresis
Many comparators oscillate in the linear region of operation because of noise or undesired parasitic feedback.
This tends to occur when the voltage on one input is
equal or very close to the voltage on the other input. The
MAX9093/MAX9095 have internal hysteresis to counter
parasitic effects and noise.
The hysteresis in a comparator creates two trip points:
one for the rising input voltage and one for the falling
input voltage (Figure 1). The difference between the trip
points is the hysteresis. When the comparator’s input
voltages are equal, the hysteresis effectively causes
one comparator input to move quickly past the other,
thus taking the input out of the region where oscillation
occurs. This provides clean output transitions for noisy,
slow-moving input signals.
1) Find output voltage when output is high:
VOUT(HIGH) = VDD - ILOAD x RL
2) Find the trip points of the comparator using these
formulas:
VTH = VREF + ((VOUT(HIGH) - VREF)R2)/(R1 + R2)
VTL = VREF(1 - (R2/(R1 + R2)))
where VTH is the threshold voltage at which the comparator switches its output from high to low as VIN rises above
the trip point, and VTL is the threshold voltage at which
the comparator switches its output from low to high as
VIN drops below the trip point.
3) The hysteresis band is:
VHYST = VTH - VTL = VDD(R2/(R1 + R2))
In this example, let VDD = 5V, VREF = 2.5V, ILOAD =
50nA, and RL = 5.1kI.
VOUT(HIGH) = 5.0V - (50 x 10-9 x 5.1 x 103I) ≈ 5.0V
VTH = 2.5 + 2.5(R2/(R1 + R2))
VTL = 2.5(1 - (R2/(R1 + R2)))
Select R2. In this example, choose 1kI.
Select VHYST. In this example, choose 50mV.
Solve for R1.
VHYST = VOUT(HIGH)(R2/(R1 + R2))V
0.050V = 5(1000/(R1 + 1000))V
where R1 ≈ 100kI, VTH = 2.525V, and VTL = 2.475V
VDD
THRESHOLDS
IN+
IN-
Additional hysteresis can be generated with two resistors using positive feedback (Figure 2). Use the following
procedure to calculate resistor values:
VHYST
HYSTERESIS
BAND
RL
R1
VTH
VTL
R2
VREF
VDD
IN+
OUT
VIN
VOUT
IN-
MAX9093/MAX9095
VSS
OUT
Figure 1. Threshold Hysteresis Band (Not to Scale)
Figure 2. Adding Hysteresis with External Resistors
9
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Chip Information
Choose R1 and R2 to be large enough as not to exceed
the amount of current the reference can supply.
The source current required is VREF/(R1 + R2).
The sink current is (VOUT(HIGH) - VREF) x (R1 + R2).
Choose RL to be large enough to avoid drawing excess
current, yet small enough to supply the necessary current to drive the load. RL should be between 1kI and
10kI. Choose R1 to be much larger than RL to avoid
lowering VOUT(HIGH) ir raising VOUT(LOW).
Board Layout and Bypassing
Use 0.1FF bypass capacitors from VDD to VSS. To maximize performance, minimize stray inductance by putting
this capacitor close to the VDD pin and reducing trace
lengths. For slow-moving input signals (rise time > 1ms),
use a 1nF capacitor between IN+ and IN- to reduce high
frequency noise.
PROCESS: BiCMOS
Ordering Information
PART
TEMP RANGE
PINPACKAGE
TOP
MARK
MAX9092AKA+
-40°C to +125°C 8 SOT23
+AESO
MAX9092AUA+*
-40°C to +125°C 8 FMAX
—
MAX9093AKA+
-40°C to +125°C 8 SOT23
+AESP
MAX9093AUA+*
-40°C to +125°C 8 FMAX
—
MAX9094ASD+*
-40°C to +125°C 14 SO
—
MAX9094AUD+*
-40°C to +125°C 14 TSSOP
—
MAX9095ASD+*
-40°C to +125°C 14 SO
—
MAX9095AUD+*
-40°C to +125°C 14 TSSOP
—
+Denotes a lead(Pb)-free/RoHS-compliant package.
*Future product—Contact factory for availability.
Package Information
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
“+”, “#”, or “-” in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
8 SOT23
K8+5
21-0078
90-0176
8 µMAX
U8+1
21-0036
90-0092
14 SO
S14+1
21-0041
90-0112
14 TSSOP
U14+1
21-0066
90-0113
10
MAX9092/MAX9093/MAX9094/MAX9095
General-Purpose, Low-Voltage,
Dual/Quad, Tiny Pack Comparators
Revision History
REVISION
NUMBER
REVISION
DATE
0
7/12
DESCRIPTION
Initial release
PAGES
CHANGED
—
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied.
Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical
Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
©
2012 Maxim Integrated Products
11
Maxim is a registered trademark of Maxim Integrated Products, Inc.