CY7C1021BN CY7C10211BN 1-Mbit (64K x 16) Static RAM Features Writing to the device is accomplished by taking Chip Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from I/O pins (I/O1 through I/O8), is written into the location specified on the address pins (A0 through A15). If Byte High Enable (BHE) is LOW, then data from I/O pins (I/O9 through I/O16) is written into the location specified on the address pins (A0 through A15). • Temperature Ranges — Commercial: 0°C to 70°C — Industrial: –40°C to 85°C — Automotive-A: –40°C to 85°C Reading from the device is accomplished by taking Chip Enable (CE) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins will appear on I/O1 to I/O8. If Byte High Enable (BHE) is LOW, then data from memory will appear on I/O9 to I/O16. See the truth table at the back of this data sheet for a complete description of read and write modes. — Automotive-E: –40°C to 125°C • High speed — tAA = 10 ns (Commercial) — tAA = 15 ns (Automotive) • CMOS for optimum speed/power • Low active power — 825 mW (max.) • Automatic power-down when deselected • Independent control of upper and lower bits • Available in Pb free and non Pb free 44-pin TSOP II and 44-pin 400-mil-wide SOJ Functional Description[1] The CY7C1021BN/CY7C10211BN is a high-performance CMOS static RAM organized as 65,536 words by 16 bits. This device has an automatic power-down feature that significantly reduces power consumption when deselected. The input/output pins (I/O1 through I/O16) are placed in a high-impedance state when the device is deselected (CE HIGH), the outputs are disabled (OE HIGH), the BHE and BLE are disabled (BHE, BLE HIGH), or during a write operation (CE LOW, and WE LOW). The CY7C1021BN/CY7C10211BN is available in standard 44-pin TSOP Type II and 44-pin 400-mil-wide SOJ packages. Customers should use part number CY7C10211BN when ordering parts with 10 ns tAA, and CY7C1021BN when ordering 12 ns and 15 ns tAA. Logic Block Diagram PinConfigurations 64K x 16 RAM Array 512 X 2048 SOJ / TSOP II Top View SENSE AMPS A7 A6 A5 A4 A3 A2 A1 A0 ROW DECODER DATA IN DRIVERS A4 A3 A2 A1 A0 CE I/O1 I/O2 I/O3 I/O4 VCC VSS I/O5 I/O6 I/O7 I/O8 WE A15 A14 A13 A12 NC I/O1–I/O8 I/O9–I/O16 COLUMN DECODER A8 A9 A10 A11 A12 A13 A14 A15 BHE WE CE OE BLE 1 44 2 3 43 42 4 41 40 39 38 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A5 A6 A7 OE BHE BLE I/O16 I/O15 I/O14 I/O13 VSS VCC I/O12 I/O11 I/O10 I/O9 NC A8 A9 A10 A11 NC Note: 1. For best-practice recommendations, please refer to the Cypress application note “System Design Guidelines” on http://www.cypress.com Cypress Semiconductor Corporation Document #: 001-06494 Rev. *A • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Revised September 28, 2006 [+] Feedback CY7C1021BN CY7C10211BN Selection Guide Maximum Access Time (ns) Maximum Operating Current (mA) Com’l / Ind’l 7C10211B-10 7C1021B-12 7C1021B-15 10 12 15 150 140 130 Automotive-A 130 Automotive-E 130 Maximum CMOS Standby Current (mA) Com’l / Ind’l Com’l / Ind’l (L version) 10 10 0.5 0.5 10 0.5 Automotive-A (L version) 0.5 Automotive-E 15 Pin Definitions Pin Name SOJ, TSOP–Pin Number A0–A15 1–5,18–21, 24–27, 42–44 I/O1–I/O16 7–10, 13–16, 29–32, 35–38 I/O Type Input Description Address Inputs used to select one of the address locations. Input/Output Bidirectional Data I/O lines. Used as input or output lines depending on operation. NC 22, 23, 28 WE 17 Input/Control Write Enable Input, active LOW. When selected LOW, a Write is conducted. When deselected HIGH, a Read is conducted. CE 6 Input/Control Chip Enable Input, active LOW. When LOW, selects the chip. When HIGH, deselects the chip. BHE, BLE 40, 39 Input/Control Byte Write Select Inputs, active LOW. BHE controls I/O16–I/O9, BLE controls I/O8–I/O1, . OE 41 Input/Control Output Enable, active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When deasserted HIGH, I/O pins are tri-stated, and act as input data pins. VSS 12, 34 VCC 11, 33 Document #: 001-06494 Rev. *A No Connect Ground No Connects. Not connected to the die. Ground for the device. Should be connected to ground of the system. Power Supply Power Supply inputs to the device. Page 2 of 10 [+] Feedback CY7C1021BN CY7C10211BN Maximum Ratings Static Discharge Voltage............................................ >2001V (per MIL-STD-883, Method 3015) (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ................................. –65°C to +150°C Latch-Up Current ..................................................... >200 mA Operating Range Ambient Temperature with Power Applied............................................. –55°C to +125°C Range Ambient Temperature (TA)[3] VCC 0°C to +70°C 5V ± 10% Supply Voltage on VCC Relative to GND[2] .... –0.5V to +7.0V Commercial DC Voltage Applied to Outputs in High Z State[2] ......................................–0.5V to VCC+0.5V Industrial –40°C to +85°C Automotive-A –40°C to +85°C Automotive-E –40°C to +125°C DC Input Voltage[2] ...................................–0.5V to VCC+0.5V Current into Outputs (LOW) .........................................20 mA Electrical Characteristics Over the Operating Range Parameter -10 Test Conditions Description Min. -12 Max. Min. -15 Max. VOH Output HIGH Voltage VCC = Min., IOH = –4.0 mA VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA VIH Input HIGH Voltage 2.2 6.0 2.2 6.0 VIL Input LOW Voltage[2] −0.5 0.8 –0.5 IIX Input Leakage Current −1 +1 –1 GND < VI < VCC 2.4 2.4 0.4 ICC ISB1 ISB2 VCC Operating VCC = Max., Supply Current IOUT = 0 mA, f = fMAX = 1/tRC Unit V 0.4 V 2.2 6.0 V 0.8 –0.5 0.8 V +1 –1 +1 µA –1 +1 µA –4 +4 µA –1 +1 µA Automotive-A –1 +1 µA Automotive-E –4 +4 µA 130 mA Com’l / Ind’l 0.4 Automotive-A Output Leakage GND < VI < VCC, Current Output Disabled Max. 2.4 Automotive-E IOZ Min. −1 Com’l / Ind’l Com’l / Ind’l +1 150 –1 +1 140 Automotive-A 130 Automotive-E 130 Automatic CE Power-Down Current—TTL Inputs Max. VCC, Com’l / Ind’l CE > VIH Automotive-A VIN > VIH or VIN < VIL, f = fMAX Automotive-E 40 40 40 Automatic CE Power-Down Current— CMOS Inputs Max. VCC, Com’l / Ind’l CE > VCC – 0.3V, Com’l / Ind’l (L) VIN > VCC – 0.3V, or VIN < 0.3V, f = 0 Automotive-A (L) 10 10 10 0.5 0.5 0.5 mA 40 50 mA 0.5 Automotive-E 15 Capacitance[4] Parameter Description CIN Input Capacitance COUT Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC = 5.0V Max. Unit 8 pF 8 pF Notes: 2. VIL (min.) = –2.0V and VIH(max) = VCC + 0.5V for pulse durations of less than 20 ns. 3. TA is the “Instant On” case temperature. 4. Tested initially and after any design or process changes that may affect these parameters. Document #: 001-06494 Rev. *A Page 3 of 10 [+] Feedback CY7C1021BN CY7C10211BN Thermal Resistance[4] Parameter ΘJA Description Test Conditions 44-pin SOJ 44-pin TSOP-II Unit 64.32 76.89 °C/W 31.03 14.28 °C/W Thermal Resistance Test conditions follow standard test methods (Junction to Ambient) and procedures for measuring thermal Thermal Resistance impedance, per EIA / JESD51. ΘJC (Junction to Case) AC Test Loads and Waveforms R 481Ω 5V R 481Ω 5V OUTPUT ALL INPUT PULSES 3.0V 90% OUTPUT R2 255 255Ω 30 pF R2 255 255Ω 5 pF INCLUDING JIG AND SCOPE (a) INCLUDING JIG AND SCOPE (b) OUTPUT Equivalent to: THÉVENIN EQUIVALENT 167 90% 10% 10% GND Rise Time: 1 V/ns Fall Time: 1 V/ns 1.73V 30 pF Switching Characteristics[5] Over the Operating Range 7C10211B-10 Parameter Description Min. Max. 7C1021B-12 Min. Max. 7C1021B-15 Min. Max. Unit Read Cycle tRC Read Cycle Time tAA Address to Data Valid tOHA Data Hold from Address Change tACE CE LOW to Data Valid 10 12 15 ns tDOE OE LOW to Data Valid 5 6 7 ns tLZOE OE LOW to Low 10 Z[6] 10 3 tHZOE OE HIGH to High CE LOW to Low Z[6] 12 5 15 6 ns 7 3 ns ns tHZCE CE HIGH to High tPU CE LOW to Power-Up tPD CE HIGH to Power-Down 10 12 15 ns tDBE Byte Enable to Data Valid 5 6 7 ns tLZBE Byte Enable to Low Z tHZBE Byte Disable to High Z 0 6 ns ns 0 3 5 ns 3 0 3 Z[6, 7] 15 3 0 Z[6, 7] tLZCE 12 0 0 0 0 5 7 ns 0 6 ns ns 7 ns Notes: 5. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0 to 3.0V, and output loading of the specified IOL/IOH and 30-pF load capacitance. 6. At any given temperature and voltage condition, tHZCE is less than tLZCE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any given device. 7. tHZOE, tHZBE, tHZCE, and tHZWE are specified with a load capacitance of 5 pF as in part (b) of AC Test Loads. Transition is measured ±500 mV from steady-state voltage. Document #: 001-06494 Rev. *A Page 4 of 10 [+] Feedback CY7C1021BN CY7C10211BN Switching Characteristics[5] Over the Operating Range (continued) 7C10211B-10 Parameter Write Cycle Description Min. 7C1021B-12 Max. Min. Max. 7C1021B-15 Min. Max. Unit [8] tWC Write Cycle Time 10 12 15 ns tSCE CE LOW to Write End 8 9 10 ns tAW Address Set-Up to Write End 7 8 10 ns tHA Address Hold from Write End 0 0 0 ns tSA Address Set-Up to Write Start 0 0 0 ns tSD Data Set-Up to Write End 5 6 8 ns tHD Data Hold from Write End 0 0 0 ns 3 3 3 ns [6] WE HIGH to Low Z tLZWE [6, 7] tHZWE WE LOW to High Z tBW Byte Enable to End of Write 5 7 6 7 8 9 ns ns Switching Waveforms Read Cycle No. 1[9, 10] tRC ADDRESS tAA tOHA DATA OUT PREVIOUS DATA VALID DATA VALID Read Cycle No. 2 (OE Controlled)[10, 11] ADDRESS tRC CE tACE OE tHZOE tDOE BHE, BLE tLZOE tHZCE tDBE tLZBE DATA OUT HIGH IMPEDANCE tLZCE VCC SUPPLY CURRENT tHZBE HIGH IMPEDANCE DATA VALID tPD tPU 50% IICC CC 50% IISB SB Notes: 8. The internal write time of the memory is defined by the overlap of CE LOW, WE LOW and BHE / BLE LOW. CE, WE and BHE / BLE must be LOW to initiate a write, and the transition of these signals can terminate the write. The input data set-up and hold timing should be referenced to the leading edge of the signal that terminates the write. 9. Device is continuously selected. OE, CE, BHE and/or BHE = VIL. 10. WE is HIGH for read cycle. Document #: 001-06494 Rev. *A Page 5 of 10 [+] Feedback CY7C1021BN CY7C10211BN Switching Waveforms (continued) Write Cycle No. 1 (CE Controlled)[12, 13] tWC ADDRESS CE tSA tSCE tAW tHA tPWE WE tBW BHE, BLE tSD tHD DATA I/O Write Cycle No. 2 (BLE or BHE Controlled) tWC ADDRESS BHE, BLE tSA tBW tAW tHA tPWE WE tSCE CE tSD tHD DATA I/O Notes: 11. Address valid prior to or coincident with CE transition LOW. 12. Data I/O is high impedance if OE or BHE and/or BLE= VIH. 13. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high-impedance state. Document #: 001-06494 Rev. *A Page 6 of 10 [+] Feedback CY7C1021BN CY7C10211BN Switching Waveforms (continued) Write Cycle No. 3 (WE Controlled, OE LOW) tWC ADDRESS tSCE CE tAW tHA tSA tPWE WE tBW BHE, BLE tHZWE tSD tHD DATA I/O tLZWE Truth Table CE OE H X X X X High Z High Z Power-Down Standby (ISB) L L H L L Data Out Data Out Read - All bits Active (ICC) L H Data Out High Z Read - Lower bits only Active (ICC) H L High Z Data Out Read - Upper bits only Active (ICC) L L Data In Data In Write - All bits Active (ICC) L H Data In High Z Write - Lower bits only Active (ICC) H L High Z Data In Write - Upper bits only Active (ICC) L X WE L BLE BHE I/O1–I/O8 I/O9–I/O16 Mode Power L H H X X High Z High Z Selected, Outputs Disabled Active (ICC) L X X H H High Z High Z Selected, Outputs Disabled Active (ICC) Document #: 001-06494 Rev. *A Page 7 of 10 [+] Feedback CY7C1021BN CY7C10211BN Ordering Information Speed (ns) Package Diagram Ordering Code 10 12 CY7C10211BN-10ZXC 51-85087 44-pin TSOP Type II Commercial CY7C1021BN-12VC 51-85082 44-pin (400-Mil) Molded SOJ Commercial CY7C1021BN-12VXC 44-pin (400-Mil) Molded SOJ (Pb-Free) CY7C1021BN-12ZC 51-85087 CY7C1021BN-12ZXC 44-pin TSOP Type II 44-pin TSOP Type II (Pb-Free) CY7C1021BN-12VI 51-85082 CY7C1021BN-12VXI 15 Operating Range Package Type 44-pin (400-Mil) Molded SOJ Industrial 44-pin (400-Mil) Molded SOJ (Pb-Free) CY7C1021BN-15VC 51-85082 CY7C1021BN-15VXC 44-pin (400-Mil) Molded SOJ Commercial 44-pin (400-Mil) Molded SOJ (Pb-Free) CY7C1021BNL-15VXC CY7C1021BN-15ZC 44-pin (400-Mil) Molded SOJ (Pb-Free) 51-85087 44-pin TSOP Type II CY7C1021BN-15ZXC 44-pin TSOP Type II (Pb-Free) CY7C1021BNL-15ZC 44-pin TSOP Type II CY7C1021BNL-15ZXC CY7C1021BN-15VI 44-pin TSOP Type II (Pb-Free) 51-85082 44-pin (400-Mil) Molded SOJ 51-85087 44-pin TSOP Type II CY7C1021BN-15VXI Industrial 44-pin (400-Mil) Molded SOJ (Pb-Free) CY7C1021BN-15ZI CY7C1021BNL-15ZI 44-pin TSOP Type II CY7C1021BN-15ZXI 44-pin TSOP Type II (Pb-Free) CY7C1021BNL-15ZXI 44-pin TSOP Type II (Pb-Free) CY7C1021BNL-15ZSXA 51-85087 44-pin TSOP Type II (Pb-Free) Automotive-A Automotive-E CY7C1021BN-15VXE 51-85082 44-pin (400-Mil) Molded SOJ (Pb-Free) CY7C1021BN-15ZSXE 51-85087 44-pin TSOP Type II (Pb-Free) Package Diagrams 44-pin (400-Mil) Molded SOJ (51-85082) 44 23 DIMENSIONS IN INCHES MIN. MAX. 0.395 0.405 0.435 0.445 22 1 SEATING PLANE 1.120 1.130 0.095 0.115 0.045 MAX. 0.128 0.148 0.023 0.033 0.013 0.023 Document #: 001-06494 Rev. *A 0.082 MIN. 0.007 0.013 0.004 0.050 TYP. 0.025 MIN. 0.365 0.375 0°-10° 51-85082-*B Page 8 of 10 [+] Feedback CY7C1021BN CY7C10211BN Package Diagrams (continued) 44-Pin TSOP II (51-85087) 51-85087-*A All products and company names mentioned in this document may be the trademarks of their respective holders. Document #: 001-06494 Rev. *A Page 9 of 10 © Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. [+] Feedback CY7C1021BN CY7C10211BN Document History Page Document Title: CY7C1021BN/CY7C10211BN (64K x 16) Static RAM Document Number: 001-06494 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 423877 See ECN NXR New Data Sheet *A 505726 See ECN NXR Removed IOS parameter from DC Electrical Characteristics table. Added Automotive products Updated ordering Information table Document #: 001-06494 Rev. *A Page 10 of 10 [+] Feedback