CREE LMD300-0040-C900-2020000 Led module driver Datasheet

Cree® LMD300, LMD400 & LMD600 LED Module Drivers
Product Description
Features
Table of Contents
•
Input voltage options: 100‑240 V,
Order Codes.................................................2
100‑277 V, 120‑277 V & 220‑240 V
Characteristics - LMD300 100- to 240‑V
0/1-10 V dimming support for
0/1-10 V Dimming Driver.............................2
reduce luminaire development time and
100‑240 V, 100‑277 V, 120‑277 V &
Characteristics - LMD300 120- to 277‑V
speed time-to-market. Cree LMD300,
220‑240 V options
0/1-10 V Dimming Driver.............................3
DALI + Touch dimming support for
Characteristics - LMD300 220- to 240‑V
220‑240 V option
0/1-10 V Dimming Driver.............................3
Optimized for Cree LMH2 2000‑,
Characteristics - LMD300 220- to 240‑V
3000‑ 4000- and 6000‑lm light
DALI + Touch Dimming Driver.....................4
sources
Characteristics - LMD400 120- to 277‑V
LMD400 enables California Title
0/1-10 V Dimming Driver.............................4
24 compliance
Characteristics - LMD600 100- to 277‑V
Cree
LED
modules
provide
lighting
designers and manufacturers with simple,
easy-to-adopt LED lighting solutions that
LMD400
and
LMD600
LED
module
•
•
drivers are specifically designed to work
with the Cree LMH2 2000-, 3000‑, 4000-
•
and 6000‑lumen light sources to jumpstart the design process for recessed
downlights, wall sconces or pendant
lights in demanding end markets such
•
as retail, museums, hospitality and
0/1-10 V Dimming Driver.............................5
restaurants.
Dimming.......................................................6
CLM-DS14 Rev 3K
LED Module Driver data sheet
Mechanical Dimensions..............................7
Wiring Diagrams........................................ 10
Thermal Design......................................... 13
Emergency Battery Operation.................. 13
Safety and Regulatory Notes.................... 14
www.cree.com/Xlamp
Packaging.................................................. 16
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are
registered trademarks and the Cree logo is a trademark of Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
Cree, Inc.
4600 Silicon Drive
Durham, NC 27703
USA Tel: +1.919.313.5300
LMD300, LMD400 & LMD600 LED Module Drivers
Order Codes
LMD300
Nominal Input
Voltage (VAC)
Frequency (Hz)
Typical Output Current
(mA)
Dimming
Order Code
100-240
50/60
900
0/1-10 V
LMD300-0040-C900-8030000
120-277
50/60
900
0/1-10 V
LMD300-0040-C900-7030000
220-240
50/60
900
0/1-10 V
LMD300-0040-C900-2030000
220-240
50/60
900
DALI + Touch
LMD300-0040-C900-2020000
Nominal Input
Voltage (VAC)
Frequency (Hz)
Typical Output Current
(mA)
Dimming
Order Code
120-277
50/60
940
0/1-10 V
LMD400-0048-C940-7030000
Nominal Input
Voltage (VAC)
Frequency (Hz)
Typical Output Current
(mA)
Dimming
Order Code
100-277
50/60
1700
0/1-10 V
LMD600-0100-C1A7-7030000
LMD400
LMD600
Characteristics - LMD300 100- to 240‑V 0/1-10 V Dimming Driver
Order Code: LMD300-0040-C900-8030000
Characteristics
Unit
Minimum
Input voltage range
VAC
90
Input power
W
40
mA
Output voltage
V
Driver efficiency (@ 55 °C) - with LMH2 2000‑lm light
source
%
85
Driver efficiency (@ 55 °C) - with LMH2 3000‑lm light
source
%
86
900
40
0.95
Power factor - with LMH2 3000‑lm light source
LED driver case temperature
Maximum
264
Output current
Power factor - with LMH2 2000‑lm light source
•
Typical
0.95
°C
0
70
3-D models (.STEP files) for the LMD300 LED module drivers are available on the Cree website by selecting the Documentation tab
on the LMH2 product page.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
2
LMD300, LMD400 & LMD600 LED Module Drivers
Characteristics - LMD300 120- to 277‑V 0/1-10 V Dimming Driver
Order Code: LMD300-0040-C900-7030000
Characteristics
Unit
Minimum
Input voltage range
VAC
108
Input power
Maximum
305
W
40
Output current
mA
900
Output voltage
V
Driver efficiency (@ 55 °C) - with LMH2 2000‑lm light
source
%
85
Driver efficiency (@ 55 °C) - with LMH2 3000‑lm light
source
%
86
40
Power factor - with LMH2 2000‑lm light source
0.95
Power factor - with LMH2 3000‑lm light source
•
Typical
0.95
Dimming current @ 120 V
mA
2.3
Dimming current @ 277 V
mA
2.3
LED driver case temperature
°C
0
70
3-D models (.STEP files) for the LMD300 LED module drivers are available on the Cree website by selecting the Documentation tab
on the LMH2 product page.
Characteristics - LMD300 220- to 240‑V 0/1-10 V Dimming Driver
Order Code: LMD300-0040-C900-2030000
Characteristics
Unit
Minimum
Typical
Maximum
Input voltage range
VAC
207
230
264
Input power
W
40
Output current
mA
900
Output voltage
V
Driver efficiency (@ 55 °C) - with LMH2 2000‑lm light
source
%
85
Driver efficiency (@ 55 °C) - with LMH2 3000‑lm light
source
%
86
39
Power factor - with LMH2 2000‑lm light source
0.95
Power factor - with LMH2 3000‑lm light source
LED driver case temperature
•
0.95
°C
0
70
3-D models (.STEP files) for the LMD300 LED module drivers are available on the Cree website by selecting the Documentation tab
on the LMH2 product page.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
3
LMD300, LMD400 & LMD600 LED Module Drivers
Characteristics - LMD300 220- to 240‑V DALI + Touch Dimming Driver
Order Code: LMD300-0040-C900-2020000
Characteristics
Unit
Minimum
Typical
Maximum
Input voltage range
VAC
207
230
264
Input power
W
40
Output current
mA
900
Output voltage
V
Driver efficiency (@ 55 °C) - with LMH2 2000‑lm light
source
%
81
Driver efficiency (@ 55 °C) - with LMH2 3000‑lm light
source
%
85
39
Power factor - with LMH2 2000‑lm light source
0.95
Power factor - with LMH2 3000‑lm light source
LED driver case temperature
•
0.95
°C
0
70
3-D models (.STEP files) for the LMD300 LED module drivers are available on the Cree website by selecting the Documentation tab
on the LMH2 product page.
Characteristics - LMD400 120- to 277‑V 0/1-10 V Dimming Driver
Order Code: LMD400-0048-C940-7030000
Characteristics
Unit
Minimum
Input voltage range
VAC
108
Input power
Maximum
305
W
48
Output current
mA
940
Output voltage
V
Driver efficiency (@ 55 °C) - with LMH2 2000‑lm light
source
%
85
Driver efficiency (@ 55 °C) - with LMH2 3000‑lm light
source
%
86
Driver efficiency (@ 55 °C) - with LMH2 4000‑lm light
source
%
87
22-44
Power factor - with LMH2 2000‑lm light source
0.95
Power factor - with LMH2 3000‑lm light source
0.95
Power factor - with LMH2 4000‑lm light source
•
Typical
0.95
Dimming current @ 120 V
mA
2.3
Dimming current @ 277 V
mA
2.3
LED driver case temperature
°C
0
90
3-D models (.STEP files) for the LMD400 LED module driver are available on the Cree website by selecting the Documentation tab on
the LMH2 product page.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
4
LMD300, LMD400 & LMD600 LED Module Drivers
Characteristics - LMD600 100- to 277‑V 0/1-10 V Dimming Driver
Order Code: LMD600-0100-C1A7-7030000
Characteristics
Unit
Minimum
Input voltage range
VAC
90
Input power
mA
Output voltage
V
Driver efficiency (@ 55 °C) - with LMH2 6000‑lm light
source
%
Maximum
305
W
Output current
102
1700
25-52
87
Power factor - with LMH2 6000‑lm light source
•
Typical
0.95
Dimming current @ 120 V
mA
Dimming current @ 277 V
mA
LED driver case temperature
°C
.05
.05
0
76
3-D models (.STEP files) for the LMD600 LED module driver are available on the Cree website by selecting the Documentation tab on
the LMH2 product page.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
5
LMD300, LMD400 & LMD600 LED Module Drivers
Dimming
The LMH2 2000-, 3000‑ and 4000‑lm light sources can use the LMD300 LED module driver with either DALI + Touch dimming or 0/110 V dimming and use the LMD400 LED module driver with 0/1-10 V dimming. The LMH2 6000‑lm light source can use the LMD600 LED
module driver with 0/1-10 V dimming.
Driver
Input Voltage
Dimming
Lowest Light Level
LMD300-0040-C900-8030000
100-240 V
0/1-10 V
10%
LMD300-0040-C900-7030000
120-277 V
0/1-10 V
10%
LMD300-0040-C900-2030000
220-240 V
0/1-10 V
10%
LMD300-0040-C900-2020000
220-240 V
DALI + Touch
10%
LMD400-0048-C940-7030000
120-277 V
0/1-10 V
10%
LMD600-0100-C1A7-7030000
100-277 V
0/1-10 V
1%
The LMH2 2000, 3000‑ and 4000‑lm light sources combined with the LMD300 DALI + Touch driver is a DALI‑certified device for use with
DALI‑compliant dimmers.
Caution - DALI dimming and Touch dimming should not be used on the same luminaire.
Setting Up the LMD300 DALI + Touch Driver in Touch Control Mode
The LMD300 DALI + Touch driver can be used in touch control mode in installations where DALI control is not installed. To set up touch
control mode, wire the driver DALI terminals to 220- to 240‑VAC mains power through a pushbutton (a momentary switch rated for 220
to 240 VAC and 0.5 A) as shown in the Wiring Diagrams section of this data sheet. Multiple LMH2 modules can be connected together to
be controlled by the same pushbutton.
To activate touch control mode, turn on power to the LMH2 LED module without pressing the pushbutton, i.e., the switch is open. After one
(1) second, the driver automatically enters touch control mode and the pushbutton can then be used to control the LMH2.
Touch Control Mode Operation
In touch control mode, a single pushbutton turns the LMH2 LED module on and off and changes its brightness. To turn the module on or
off, press and release the pushbutton quickly (in less than 300 ms). When the module is on, change its brightness by pressing and holding
the pushbutton. The brightness alternately increases or decreases each time the pushbutton is pressed and held. When the desired
brightness is reached, release the pushbutton. The module will remain at this brightness level until the pushbutton is pressed and held
again, even if it is turned off and back on.
Two methods can be used to quickly reach maximum and minimum brightness. For maximum brightness instantly, double-click the
pushbutton when the LMH2 LED module is on. Double-clicking means quickly pressing and releasing the pushbutton twice in succession
(with less than 300 ms between presses). For minimum brightness, press and hold the pushbutton when the LMH2 is off. The LMH2 LED
module turns on at minimum brightness and increases in brightness until the pushbutton is released.
If multiple LMH2 LED modules are controlled by the same pushbutton, the modules can lose synchronization and not all perform the
same action in response to the pushbutton. To synchronize all the modules connected to one pushbutton, press and hold the pushbutton
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
6
LMD300, LMD400 & LMD600 LED Module Drivers
for at least one (1) second and release it, then double-click the pushbutton. All connected modules will then be on at maximum brightness,
regardless of their previous states.
Touch control mode operation is summarized in the following table.
Module Operation in Touch Mode
Pushbutton Operation
Module On
All off
All on at previous brightness
Brightness increases or decreases opposite of
previous press and hold
All on at minimum brightness, increasing brightness
while pushbutton held
Click
Press and hold
Module Off
All on at maximum brightness
Double-click
Mechanical Dimensions
Physical Characteristics of the LMD300, LMD400 & LMD600 Drivers
LMD300
100- to 240-V
Driver
Physical Characteristic
8
LMD300
120- to 277-V
Driver
LMD300
220- to 240-V
Drivers
431.8
LMD400
120- to 277-V
Driver
LMD600
100- to 277-V Driver
440
Weight (g)
195
195
264
280
Maximum height (mm)
37.5
37.5
35
37.5
Maximum length (mm)
90
90
205
90
160
Maximum width (mm)
90
90
80
90
63
7
6
47
5
LMD300 100- to 240‑V and LMD300 & LMD400 120- to 277-V Drivers1
180 ± 10
STRIPPED 10
90
76.6
37.5
30
45
90
30
76.6
20
7.5
7.5
WIRE ROUTING SLOT
TYP 9X
1
40
Tc LOCATION
M3 OR #6
MOUNTING SLOT
TYP 2X
Dimensions for all the diagrams are in mm and are for reference only. For exact dimensions and tolerances, refer to the 3-D models (.STEP files) for
the LMD300, LMD400 and LMD600 drivers available by selecting the Documentation tab on the LMH2 product page.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
7
LMD300, LMD400 & LMD600 LED Module Drivers
LMD300 220- to 240-V Driver - With Standard Covers
205
196
205
185
196
185
80
80 50
50
Tc LOCATION
80
Tc
M3LOCATION
OR #6
MOUNTING SLOT
TYP #6
2X
M3 OR
MOUNTING SLOT
TYP 2X
80
35
35
205
196
LMD300 220- to 240-V Driver - With Optional Conduit Covers 185
205
205
196
196
185
185
80
50
80
80
50
50
80
M3 OR #6
MOUNTING SLOT
TYP 2X
80
80
M3 OR #6 35
M3 OR
#6
MOUNTING
SLOT
MOUNTING
SLOT
TYP
2X
TYP 2X
35
35
40
40
40
20 KNOCKOUT
TYP 4X
20 KNOCKOUT
TYP204XKNOCKOUT
TYP 4X
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
8
LMD300, LMD400 & LMD600 LED Module Drivers
LMD600 100- to 277-V Driver
160
61.6
23
23
50
47
47
Tc
6-32 MOUNTING
MOUNTING
6-32
STUDS
STUDS
39
39
88
WIRE
WIRE LL == 150mm
150mm
TYP.
TYP.
1144
..44
50.8
63
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
9
LMD300, LMD400 & LMD600 LED Module Drivers
Wiring Diagrams
Electrical Connection
For the 100- to 240‑V, 100- to 277‑V and 120- to 277‑V LED module drivers, LMH2 LED module operation is accomplished by connecting
the AC mains to the two (2) lead wires (line and neutral) from the driver and connecting the driver output wires to the input leads on the
Cree LMH2 light source, as indicated in the following wiring diagrams. For the 220- to 240‑V LED module drivers, module operation is
accomplished by connecting the AC mains to the appropriate terminal block pins.
The 100- to 240‑V and 120- to 277‑V LED module driver lead wires are 152.4 mm long, 18 AWG with the ends stripped 10 mm. The 100- to
277‑V LED module driver lead wires are 150 mm long, 18 AWG with the ends stripped 10 mm. The 220- to 240‑V LED module drivers have
poke‑in terminals.
LMD300 100- to 240‑V Driver
0/1-10V CONTROL
BLK - HOT
RED
WHT - NEU
BLK
TO LIGHT
SOURCE
VIO
GRY
BLK - HOT
RED
WHT - NEU
BLK
TO LIGHT
SOURCE
VIO
GRY
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
10
LMD300, LMD400 & LMD600 LED Module Drivers
LMD300 & LMD400 120- to 277‑V Drivers
LMD300/
LMD400
LMD300/
LMD400
LMD300 220- to 240‑V 0/1 - 10 V and DALI + Touch Dimming Drivers - Touch Operation Not Required
TO DALI BUS OR 0/1-10 V
LMD300
LMD300
LMD300
LMD300
LMD300
LMD300
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
11
LMD300, LMD400 & LMD600 LED Module Drivers
LMD300 220- to 240-V DALI + Touch Driver
LMD300
LMD300
LMD300
LMD300
LMD300
LMD300
LMD600 100- to 277‑V Driver
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
12
LMD300, LMD400 & LMD600 LED Module Drivers
Wiring Strain Relief
LMD300, LMD400 and LMD600 LED module drivers must not be suspended directly by the leads. Though the wiring from the LMD300,
LMD400 and LMD600 LED module drivers is internally strain relieved, additional strain relief methods must be employed if the luminaire
is to be suspended solely by the wiring, as in a pendant luminaire.
Thermal Design
Expected LMD300 Lifetime versus Temperature at Tc Point
Tc (°C) @ 25 °C Room Ambient
Expected Operation Life (Hours)
LMD300
100- to 240-V 0/1-10 V
Dimming Driver
LMD300
120- to 277-V
0/1-10 V Dimming Driver
LMD300
220- to 240-V
0/1-10 V Dimming Driver
LMD300
220- to 240-V
DALI + Touch Dimming
Driver
35,000
70
70
70
70
50,000
65
65
65
65
Expected LMD400 Lifetime versus Temperature at Tc Point
Tc (°C) @ 25 °C Room Ambient
Expected Operation Life (Hours)
LMD400
120- to 277-V
0/1-10 V Dimming Driver
35,000
90
50,000
80
Expected LMD600 Lifetime versus Temperature at Tc Point
Tc (°C) @ 25 °C Room Ambient
Expected Operation Life (Hours)
LMD600
100- to 277-V
0/1-10 V Dimming Driver
50,000
76
Emergency Battery Operation
The LMD300, LMD400 and LMD600 LED module drivers are constant‑current supplies. Interrupting the driver current with a battery supply
is an acceptable method of emergency or power outage operation. An acceptable installation should also include a switching mechanism
that prevents the battery power from entering the driver through the DC output leads. Confirming backup power supply compatibility is
the responsibility of the luminaire manufacturer or installer. Please refer to the backup power supply manufacturer’s instructions for
installation and further product information.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
13
LMD300, LMD400 & LMD600 LED Module Drivers
Safety and Regulatory Notes
The following tables show the safety and regulatory certifications for the LMD300 and LMD400 LED module drivers.
LMD300 100- to 240‑VAC Driver
Standard
J61347-1 (H20)
J61347-1 (H21)
Safety
File Number
CJP2012109004-0578
EN 61347-1
EN 61347-2-13
CE SELV equivalent
CJP2012109004-0578
IP-20
EN 55015
Electromagnetic
compatibility
IEC 61000-3-2
IEC 61000-3-3
CJP2012109004-0578
IEC 61547
Environmental
RoHs
LMD300 & LMD400 120- to 277‑VAC Drivers
Standard
LMD300 220- to 240‑VAC Driver
File Number
Standard
File Number
UL®/cUL recognized (UL8750)
Class 2 power supply
UL – Damp rated
E333437
Air handling (plenum)
Safety
5VA flame rating
EN 61347-1
EN 61347-2-13
CE SELV equivalent
EN 61347-1
RZCE2012-0221LVD
101342922CHI-001
IP-20
Electromagnetic
compatibility
EN 61347-2-13
CE SELV equivalent
IP-20
EN 55015
EN 55015
IEC 61000-3-2
IEC 61000-3-2
IEC 61000-3-3
IEC 61547
RZCE2012-0205LVD
RZCE2012-0512LVD
RZCE2012-0574LVD-M1
RZCE2012-0221EMC
R10051625-EMC
IEC 61000-3-3
RZCE2012-0205EMC
RZCE2012-0512EMC
RZCE2012-0574EMC-M1
IEC 61547
FCC 47 CFR Part 15 Class B/
ICES 03
Regulatory
Environmental
IEEE C.62.41-1991 Class A (surge)
NEMA 410
RoHS
RoHs
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
14
LMD300, LMD400 & LMD600 LED Module Drivers
LMD600 100- to 277‑VAC Driver
Standard
File Number
UL/cUL recognized (UL8750)
Class 2 power supply
UL – Damp rated
E333437
Air handling (plenum)
Safety
5VA flame rating
EN 61347-1
EN 61347-2-13
CE SELV equivalent
101564185CHI-001
IP-20
EN 55015
IEC 61000-3-2
Electromagnetic
compatibility
IEC 61000-3-3
R10273893-EMC
IEC 61547
FCC 47 CFR Part 15 Class B/
ICES 03
Environmental
RoHS
Safety Certification
Together, the LMH2 light source combined with the LMD300, LMD400 or LMD600 LED module driver is “suitable for damp locations;
covered ceilings.” Final luminaire designs should go through safety certification as required, which is the responsibility of the luminaire
manufacturer.
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
15
LMD300, LMD400 & LMD600 LED Module Drivers
Packaging
LMD300 100- to 240–V LED module drivers are packaged in boxes of 10, which are then combined in cartons of 5 boxes, or 50 LMD300
120- to 240–V drivers.
LMD300 and LMD400 120- to 277–V LED module drivers are packaged in boxes of 10, which are then combined in cartons of 5 boxes, or
50 LMD300 or LMD400 120- to 277–V drivers.
LMD300 220- to 240‑V LED module drivers are packaged in boxes of 5, which are then combined in cartons of 10 boxes, or 50 LMD300
220- to 240‑V drivers.
LMD600 100- to 277–V LED module drivers are packaged in boxes of 5, which are then combined in cartons of 5 boxes, or 25 LMD600
100- to 277–V drivers.
Box and carton sizes are as follows.
Box of 10 LMD300 100- to 240-V LED module drivers: 255 x 194 x 98 mm
Carton of 5 LMD300 100- to 240-V driver boxes: 509 x 275 x 222 mm
Box of 10 LMD300 or LMD400 120- to 277-V LED module drivers: 255 x 194 x 98 mm
Carton of 5 LMD300 or LMD400 120- to 277-V driver boxes: 509 x 275 x 222 mm
Box of 5 LMD300 220- to 240‑V LED module drivers: 285 x 211 x 91 mm
Carton of 10 LMD300 220- to 240‑V driver boxes: 588 x 471 x 243 mm
Box of 5 LMD600 100- to 277‑V LED module drivers: 490 x 235 x 90 mm
Carton of 5 LMD600 100- to 270‑V driver boxes: 510 x 510 x 255 mm
Copyright © 2013-2016 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree® and XLamp® are registered trademarks and the Cree logo is a trademark of
Cree, Inc. UL® and the UR logo are registered trademarks of UL LLC.
16
Similar pages