ISSI IS61LV25616 256K x 16 HIGH SPEED ASYNCHRONOUS CMOS STATIC RAM WITH 3.3V SUPPLY FEATURES ® AUGUST 2000 DESCRIPTION The ISSI IS61LV25616 is a high-speed, 4,194,304-bit static • High-speed access time: — 7, 8, 10, 12, and 15 ns • CMOS low power operation • Low stand-by power: — Less than 5 mA (typ.) CMOS stand-by • TTL compatible interface levels • Single 3.3V power supply • Fully static operation: no clock or refresh required • Three state outputs • Data control for upper and lower bytes • Industrial temperature available RAM organized as 262,144 words by 16 bits. It is fabricated using ISSI's high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields high-performance and low power consumption devices. When CE is HIGH (deselected), the device assumes a standby mode at which the power dissipation can be reduced down with CMOS input levels. Easy memory expansion is provided by using Chip Enable and Output Enable inputs, CE and OE. The active LOW Write Enable (WE) controls both writing and reading of the memory.A data byte allows Upper Byte (UB) and Lower Byte (LB) access. The IS61LV25616 is packaged in the JEDEC standard 44-pin 400-mil SOJ, 44-pin TSOP Type II, 44-pin LQFP and 48-pin Mini BGA (8mm x 10mm). FUNCTIONAL BLOCK DIAGRAM A0-A17 DECODER 256K x 16 MEMORY ARRAY I/O DATA CIRCUIT COLUMN I/O VCC GND I/O0-I/O7 Lower Byte I/O8-I/O15 Upper Byte CE OE WE CONTROL CIRCUIT UB LB ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which may appear in this publication. © Copyright 2000, Integrated Silicon Solution, Inc. Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 1 ISSI IS61LV25616 ® PIN CONFIGURATIONS 44-Pin TSOP (Type II) and SOJ 48-Pin mini BGA 1 2 A17 A16 A15 OE UB LB I/O15 I/O14 I/O13 I/O12 GND Vcc I/O11 I/O10 I/O9 I/O8 NC A14 A13 A12 A11 A10 A17 A16 A15 A14 A13 A12 A11 A10 OE UB LB 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 CE I/O0 I/O1 I/O2 I/O3 Vcc GND I/O4 I/O5 I/O6 I/O7 44 43 42 41 40 39 38 37 36 35 34 33 1 32 2 31 3 30 4 29 5 TOP VIEW 28 6 27 7 26 8 25 9 24 10 23 11 12 13 14 15 16 17 18 19 20 21 22 I/O15 I/O14 I/O13 I/O12 GND Vcc I/O11 I/O10 I/O9 I/O8 NC WE A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A0 A1 A2 A3 A4 CE I/O0 I/O1 I/O2 I/O3 Vcc GND I/O4 I/O5 I/O6 I/O7 WE A5 A6 A7 A8 A9 44-Pin LQFP PIN DESCRIPTIONS 2 3 4 5 6 A0-A17 Address Inputs I/O0-I/O15 Data Inputs/Outputs CE Chip Enable Input OE Output Enable Input A1 A2 N/C WE Write Enable Input A3 A4 CE I/O0 LB Lower-byte Control (I/O0-I/O7) I/O10 A5 A6 I/O1 I/O2 UB Upper-byte Control (I/O8-I/O15) I/O11 A17 A7 I/O3 Vcc NC No Connection I/O12 NC A16 I/O4 GND Vcc Power I/O14 I/O13 A14 A15 I/O5 I/O6 GND Ground G I/O15 NC A12 A13 WE I/O7 H NC A8 A9 A10 A11 NC A LB OE A0 B I/O8 UB C I/O9 D GND E Vcc F Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 ISSI IS61LV25616 ® TRUTH TABLE I/O PIN I/O0-I/O7 I/O8-I/O15 WE CE OE LB UB Not Selected X H X X X High-Z High-Z ISB1, ISB2 Output Disabled H X L L H X X H X H High-Z High-Z High-Z High-Z I CC Read H H H L L L L L L L H L H L L DOUT High-Z DOUT High-Z DOUT DOUT I CC Write L L L L L L X X X L H L H L L DIN High-Z DIN High-Z DIN DIN I CC Mode 1 Vcc Current 2 3 4 5 ABSOLUTE MAXIMUM RATINGS(1) Symbol Parameter Value Unit –0.5 to Vcc+0.5 V VTERM Terminal Voltage with Respect to GND TBIAS Temperature Under Bias –45 to +90 °C VCC Vcc Related to GND –0.3 to +4.0 V TSTG Storage Temperature –65 to +150 °C PT Power Dissipation 1.0 W 6 7 8 Note: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 9 10 OPERATING RANGE Range Commercial Industrial Ambient Temperature 7, 8, 10 ns VCC 12 ns, 15 ns VCC 0°C to +70°C 3.3V +10%, -5% 3.3V ± 10% –40°C to +85°C 3.3V +10%, -5% 3.3V ± 10% Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 11 12 3 ISSI IS61LV25616 ® DC ELECTRICAL CHARACTERISTICS (Over Operating Range) Symbol Parameter Test Conditions Min. Max. Unit VOH Output HIGH Voltage VCC = Min., IOH = –4.0 mA 2.4 — V VOL Output LOW Voltage VCC = Min., IOL = 8.0 mA — 0.4 V VIH Input HIGH Voltage 2.0 VCC + 0.3 V VIL Input LOW Voltage(1) –0.3 0.8 V ILI Input Leakage GND ≤ VIN ≤ VCC Com. Ind. –1 –5 1 5 µA ILO Output Leakage GND ≤ VOUT ≤ VCC, 4 Outputs Disabled Com. Ind. –1 –5 1 5 µA Notes: 1. VIL (min.) = –2.0V for pulse width less than 10 ns. POWER SUPPLY CHARACTERISTICS(1) (Over Operating Range) -7, -8 Min. Max. -10 Min. Max. -12 Min. Max. -15 Min. Max. Symbol Parameter Test Conditions Unit ICC Vcc Dynamic Operating Supply Current VCC = Max., Com. IOUT = 0 mA, f = fMAX Ind. — — 260 300 — — 260 300 — — 240 280 — — 220 250 mA ISB TTL Standby Current (TTL Inputs) VCC = Max., VIN = VIH or VIL CE ≥ VIH, f = fMAX. Com. Ind. — — 85 95 — — 85 95 — — 75 85 — — 65 75 mA ISB1 TTL Standby Current (TTL Inputs) VCC = Max., VIN = VIH or VIL CE ≥ VIH, f = 0 Com. Ind. — — 20 25 — — 20 25 — — 20 25 — — 20 25 mA ISB2 CMOS Standby Current (CMOS Inputs) VCC = Max., Com. CE ≥ VCC – 0.2V, Ind. VIN ≥ VCC – 0.2V, or VIN ≤ 0.2V, f = 0 — — 10 15 — — 10 15 — — 10 15 — — 10 15 mA Note: 1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change. Shaded area product in development CAPACITANCE(1) Symbol Parameter CIN Input Capacitance COUT Input/Output Capacitance Conditions Max. Unit VIN = 0V 6 pF VOUT = 0V 8 pF Note: 1. Tested initially and after any design or process changes that may affect these parameters. 4 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 ISSI IS61LV25616 ® READ CYCLE SWITCHING CHARACTERISTICS(1) (Over Operating Range) Symbol tRC tAA tOHA tACE tDOE tHZOE(2) tLZOE(2) tHZCE(2 tLZCE(2) tBA tHZB(2) tLZB(2) tPU tPD Parameter -7 Min. Max. -8 Min. Max. -10 Min. Max. -12 Min. Max. -15 Min. Max. 1 Unit Read Cycle Time 7 — 8 — 10 — 12 — 15 — ns Address Access Time — 7 — 8 — 10 — 12 — 15 ns Output Hold Time 3 — 3 — 3 — 3 — 3 — ns CE Access Time — 7 — 8 — 10 — 12 — 15 ns OE Access Time — 3.5 — 3.5 — 4 — 5 — 7 ns OE to High-Z Output — 2.5 — 3 — 4 — 5 0 6 ns OE to Low-Z Output 0 — 0 — 0 — 0 — 0 — ns CE to High-Z Output 0 3 — 3 0 4 0 6 0 8 ns CE to Low-Z Output 2.5 — 3 — 3 — 3 — 3 — ns LB, UB Access Time — 3 — 3.5 — 4 — 5 — 7 ns LB, UB to High-Z Output 0 2.5 0 3 0 3 0 4 0 5 ns LB, UB to Low-Z Output 0 — 0 — 0 — 0 — 0 — ns Power Up Time 0 — 0 — 0 — 0 — 0 — ns Power Down Time — 7 — 8 — 10 — 12 — 15 ns 2 3 4 5 Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0V to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Shaded area product in development 6 7 AC TEST CONDITIONS Parameter Input Pulse Level Input Rise and Fall Times Input and Output Timing and Reference Level Output Load Unit 0V to 3.0V 3 ns 1.5V 8 See Figures 1 and 2 9 AC TEST LOADS 10 319 Ω ZO = 50Ω 3.3V 50Ω 11 1.5V OUTPUT OUTPUT 30 pF Including jig and scope Figure 1 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 5 pF Including jig and scope 353 Ω 12 Figure 2 5 ISSI IS61LV25616 ® AC WAVEFORMS READ CYCLE NO. 1(1,2) (Address Controlled) (CE = OE = VIL, UB or LB = VIL) t RC ADDRESS t AA t OHA t OHA DOUT DATA VALID PREVIOUS DATA VALID READ1.eps READ CYCLE NO. 2(1,3) tRC ADDRESS tAA tOHA OE tHZOE tDOE tLZOE CE tACE tHZCE tLZCE LB, UB DOUT VCC HIGH-Z tBA tLZB tHZB tRC DATA VALID tPU 50% Supply Current tPD ICC 50% ISB UB_CEDR2.eps Notes: 1. WE is HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE, UB, or LB = VIL. 3. Address is valid prior to or coincident with CE LOW transition. 6 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 ISSI IS61LV25616 ® WRITE CYCLE SWITCHING CHARACTERISTICS(1,3) (Over Operating Range) Symbol Parameter -7 Min. Max. -8 Min. Max. -10 Min. Max. -12 Min. Max. -15 Min. Max. tWC Write Cycle Time 7 — 8 — 10 — 12 — 15 — ns tSCE CE to Write End 5 — 5.5 — 8 — 8 — 10 — ns tAW Address Setup Time to Write End 5 — 5.5 — 8 — 8 — 10 — ns tHA Address Hold from Write End 0 — 0 — 0 — 0 — 0 — ns tSA Address Setup Time 0 — 0 — 0 — 0 — 0 — ns tPWB LB, UB Valid to End of Write 5 — 5.5 — 8 — 8 — 10 — ns tPWE1 WE Pulse Width 5 — 5.5 — 8 — 8 — 10 — ns tPWE2 WE Pulse Width (OE = LOW) 7 — 5 — 10 — 12 — 12 — ns tSD Data Setup to Write End 3.5 — 4 — 6 — 6 — 7 — ns tHD 1 Unit Data Hold from Write End 0 — 0 — 0 — 0 — 0 — ns (2) tHZWE WE LOW to High-Z Output — 3 — 3.5 — 5 — 6 — 7 ns (2) tLZWE WE HIGH to Low-Z Output 2 — 2 — 2 — 2 — 2 — ns 2 3 4 5 Notes: 1. Test conditions assume signal transition times of 3 ns or less, timing reference levels of 1.5V, input pulse levels of 0V to 3.0V and output loading specified in Figure 1. 2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested. 3. The internal write time is defined by the overlap of CE LOW and UB or LB, and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the write. Shaded area product in development 6 7 8 9 10 11 12 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 7 ISSI IS61LV25616 ® AC WAVEFORMS WRITE CYCLE NO. 1 (CE Controlled, OE is HIGH or LOW) (1 ) t WC VALID ADDRESS ADDRESS t SA t SCE t HA CE t AW t PWE1 t PWE2 WE t PBW UB, LB t HZWE DOUT DATA UNDEFINED t LZWE HIGH-Z t SD DIN t HD DATAIN VALID UB_CEWR1.eps Notes: 1. WRITE is an internally generated signal asserted during an overlap of the LOW states on the CE and WE inputs and at least one of the LB and UB inputs being in the LOW state. 2. WRITE = (CE) [ (LB) = (UB) ] (WE). 8 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 ISSI IS61LV25616 ® AC WAVEFORMS WRITE CYCLE NO. 2 (WE Controlled. OE is HIGH During Write Cycle) (1,2) 1 t WC ADDRESS VALID ADDRESS 2 t HA OE CE 3 LOW t AW t PWE1 WE t SA 4 t PBW UB, LB t HZWE DOUT t LZWE 5 HIGH-Z DATA UNDEFINED t SD t HD DATAIN VALID DIN 6 UB_CEWR2.eps 7 WRITE CYCLE NO. 3 (WE Controlled. OE is LOW During Write Cycle) (1) t WC ADDRESS OE 8 VALID ADDRESS t HA LOW 9 CE LOW t AW 10 t PWE2 WE t SA t PBW 11 UB, LB t HZWE DOUT DATA UNDEFINED t LZWE HIGH-Z t SD DIN 12 t HD DATAIN VALID UB_CEWR3.eps Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 9 ISSI IS61LV25616 ® AC WAVEFORMS WRITE CYCLE NO. 4 (LB, UB Controlled, Back-to-Back Write) (1,3) t WC ADDRESS t WC ADDRESS 1 ADDRESS 2 OE t SA CE LOW t HA t SA WE UB, LB t HA t PBW t PBW WORD 1 WORD 2 t HZWE DOUT t LZWE HIGH-Z DATA UNDEFINED t HD t SD DIN DATAIN VALID t HD t SD DATAIN VALID UB_CEWR4.eps Notes: 1. The internal Write time is defined by the overlap of CE = LOW, UB and/or LB = LOW, and WE = LOW. All signals must be in valid states to initiate a Write, but any can be deasserted to terminate the Write. The t SA, t HA, t SD, and t HD timing is referenced to the rising or falling edge of the signal that terminates the Write. 2. Tested with OE HIGH for a minimum of 4 ns before WE = LOW to place the I/O in a HIGH-Z state. 3. WE may be held LOW across many address cycles and the LB, UB pins can be used to control the Write function. 10 Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 ISSI IS61LV25616 ORDERING INFORMATION Commercial Range: 0°C to +70°C Speed (ns) Industrial Range: –40°C to +85°C Order Part No. Package 1 IS61LV25616-8TI IS61LV25616-8KI IS61LV25616-8LQI IS61LV25616-8BI TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) 2 10 IS61LV25616-10TI IS61LV25616-10KI IS61LV25616-10LQI IS61LV25616-10BI TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) 3 TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) 12 IS61LV25616-12TI IS61LV25616-12KI IS61LV25616-12LQI IS61LV25616-12BI TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) IS61LV25616-12T IS61LV25616-12K IS61LV25616-12LQ IS61LV25616-12B TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) 15 IS61LV25616-15TI IS61LV25616-15KI IS61LV25616-15LQI IS61LV25616-15BI TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) IS61LV25616-15T IS61LV25616-15K IS61LV25616-15LQ IS61LV25616-15B TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) Order Part No. Package IS61LV25616-7T IS61LV25616-7K IS61LV25616-7LQ IS61LV25616-7B TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) 8 8 IS61LV25616-8T IS61LV25616-8K IS61LV25616-8LQ IS61LV25616-8B TSOP (Type II) 400-mil SOJ LQFP Mini BGA (8mm x 10mm) 10 IS61LV25616-10T IS61LV25616-10K IS61LV25616-10LQ IS61LV25616-10B 12 15 7 ® Speed (ns) 4 5 6 Shaded area product in development 7 Shaded area product in development 8 9 ® 10 Integrated Silicon Solution, Inc. 11 ISSI 2231 Lawson Lane Santa Clara, CA 95054 Tel: 1-800-379-4774 Fax: (408) 588-0806 E-mail: [email protected] www.issi.com Integrated Silicon Solution, Inc. — 1-800-379-4774 Rev. B 09/29/00 11 12